Conservation of Mahadeva Temple Koothattukulam, Ernakulam District, Kerala

CIVIL WORKS

DISMANTLING

Dismantling tiled roofing with battens, boarding etc. complete including stacking of serviceable material and disposal of unserviceable material within 50 metres lead.

Dismantling roofing including ridges, hips, velleys and gutters etc., and stacking the material within 50 metres lead of :G.S. Sheet

Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead.

Demolishing R.C.C. work manually / by mechanical means including stacking of steel bars and disposal of unserviceable material with in 50 metres lead as per direction of Engineer -in-Charge.

Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Demolishing lime concrete manually / by mechanical means and disposal of material within 50 metres lead as per direction of Engineer - in- Charge.

Dismantling doors, windows and clerestory windows (steel or wood ) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead:Of area 3 sq. metres and below

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

Raking out joints of stone masonry surface to the required width and depth, with due care and precaution, by mechanical / manual means, including preparing and cleaning the surface for re pointing / refilling of joints, including disposal of rubbish to the dumping ground with in 50 metre lead.

Applying two or more coat of Ethyl Silicate chemical as approved by Archaeological Survey of India / Engineer -in-Charge, of approved brand and manufacturer, with brush or spray on the existing stone masonry surface till there is no further absorption of chemical by stone surface, including protecting the applied surface from direct sunlight by suitable means during application, all complete as per direction of the Engineer-in-Charge ( The rate is inclusive of all materials & labours involved except scaffolding )

Disposal of building rubbish/ malba/ similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved

Dismantling and removing the wrought and framed work of timbers in roof,brackets doors,windows and floors including removing cleats and wooden nails end of balustrades including lowering, stacking the useful materials and disposal of debris etc including extra lowering charge and scaffolding charges complete within a distance of 150m.

Dismantling and removing any thickness of walls in laterite or bricks in lime or cement mortar including disposal of debris and stacking useful materials within a distance of 150 m .

Removing the paint from old timber surfaces using chemical paint remover like methylene chloride etc (not with sodium hyroxide) method and cleaning surfaces with sand paper, cotton waste, etc. including cost and conveyance of all materials ,labour charges,scaffolding etc

Removing the paint from old timber surfaces using flame method and cleaning surfaces with sand paper, cotton waste, etc.

Thoroughly scrubbing, scrapping and cleaning the thickly white washed surface in several layers over the lime plastering using proper tools and different grade sand papers without making any damages in the wall surface and rectifying the petty damages wherever seen using proper materials to match the existing surface

WOOD WORK

Fixing available well seasoned second class teak wood roof members in places of damaged one and already removed from position such as door and window frames, rafters, ridge, wall plate, collar, collar pin, flooring joists etc including all labour for ornamental cutting, steps, moulding etc. wherever necessary as per the existing size and shape using already dismantled departmental roof members including all scaffolding charges.

Supplying and fixing 12 mm thick teak wood planks for ceiling/flooring below the joists ,rafter already fixed using necessary GI screws after removing the decayed ceiling planks etc. complete as per the direction of Engineer in Charge

Providing and fixing 25 mm thick well seasoned first class country wood planks ( deodar) approved by consultant over roof up to a height of 20 m in conical shape including 50 mm nails and finishing smooth and filling the joints with wooden filler, for receiving the copper sheet roofing as per site condition and including scaffoldingup to 20 m height complete direction of the engineer in charge

Fixing available second class teak wood reepers(as per existing pattern) using departmental reepers after cutting, sizing making columb/special lap joint and providing the same in position with new nails including all cost of fixing etc as directed by Engineer in charge.

Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in charge.

Providing and fixing bright finished brass parliamentary hinges with necessary screws etc. complete:150x125x27x5 mm

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete:200x10 mm

Providing and fixing bright finished door latch with necessary screws etc. complete:300x16x5 mm

Providing and fixing 150x10 mm passivated bolt with 50mm x 4mm passivated rod welded to bolt head for holdfast including fixing to frame embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Strengthening the existing wooden beams,columns etc by inserting steel plates, angles flats etc. as per drawing, including cost and conveyance of steel plates, nuts, bolts, screw, fabricating, fixing complete as directed by Engineer-in-charge.

Making joints with available wood work like rafter, beams,wall plate of cross sectional area upto 100 sq. centimetres including cutting and making Half-lap joints upto 45 cm lapping including drilling 10mm dia holes for receiving bolts for reusing old timber work.complete job as per the direction of Engineer in charge

Making joints with available wood work like rafter, beams,wall plate of cross sectional area beyond 100 sq. centimetres upto 600 sq.centimetres including cutting and making Half-lap joints upto 60 cm lapping including drilling 10mm dia holes for receiving bolts for reusing old timber work.complete job as per the direction of Engineer in charge.

Labour charge for fixing roof Mughappu and doing decorative works in traditional style as listed below but not limited to the following using good quality well seasoned second class Teak wood

Providing and fixing well seasoned second class teak wood roof members in places of damaged one and already removed from position such as door and window frames, rafters, ridge, wall plate,collar, collar pin, flooring joists,eve boards etc as per site condition/approved design including all labour for ornamental works, cutting, steps, moulding etc. wherever necessary as per the existing size and shape including all scaffolding charges. Wooden members has to undergo seasoning

Providing and fixing second class teak wood column of size 300 mm X 300 mm necessary materials & per the existing design including charges for fixing as directed by Engineer in Charge.

Supplying and fixing up to 40 mm thick teak wood planks for ceiling/flooring over the joists and secondary already fixed using 60 mm GI screws and removing the decayed ceiling planks etc. Complete.

Providing and fixing second class teak Solid wooden door and window shutter having 60 mm thick with necessary wooden pivot / oxidised iron butt hinges with necessary screws planks jointed with 25 X 80 mm reepers with necessary iron screws complete job as per the direction of Engineer in Charge.

Providing and fixing second quality teak wood reepers (as per existing pattern) of required size after cutting, shaping,making Columb/special lap joint and providing the same in position including cost of all materials as directed by Engineer in charge

Providing and fixing second class teak Solid wooden door and window shutter having 35 mm thick with necessary wooden pivot / oxidised iron butt hinges with necessary screws planks jointed with 25 X 80 mm teak wood reepers with necessary iron screws complete job as per the direction of Engineer in Charge.

Providing and fixing second class teak wood Eve boards of size 250 mm X 32 mm at the edges of rafter roof with necessary screws & per the existing design including charges for scaffolding charges as directed by Engineer in Charge.

MASONRY WORK

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

Laterite masonry in lime mortar 1:2:9(1cement:2 lime:9 fine sand ) using existing size or nearest available size of laterite for superstructure., including cost and conveyance of all materials, labour,scaffolding, curing, lead lift , etc complete at all levels and as directed by Engineer-in-charge. Preparation of lime may be as per specification 6.0 attached

ROOFING WORK

Cleaning MP tiles, hip and ridge tiles by removing water weeds, fungi etc using wire brush and lime water including extra lowering charge and scaffolding charges(considered only resuable tile)

Labour charge for Roofing with departmentaly supplied MP roofing tiles including extra labour with raised up mughappu, false ceiling, obstructions, additional works in valleying areas etc. including necessary scaffolding complete as per the instruction of engineer in charge

Providing and fixing 24 gauge Copper plate on roof upto 20 m height in conical shape with side moulding and interlocking each other and fixing with 20 mm copper nail. Overlapping should not be less than 0.6 of the area of the sheet. Water tightness should be at all level the purity of the copper plate has to be tested in lab get approved by the authority before fixing. The entire exposed area has to be painted with metalic paint 2 or more coat including a base coat of Etch primer. The cost including material, nails and scaffoldingup to 20 m height complete job as per the direction of the engineer in charge.

Providing and laying approved make, MP tiles of 320 mm or nearest size over reeper bands (already done) to correct lines and levels including the cost, conveyance of all materials etc. Including extra lowering charge and scaffolding charges complete as directed by Engineer-in-charge.

Providing & fixing on ceiling factory pressed clay decorative floral tile (under mangalore tile roof) of 320mm x 200 mm x 12mm and as per approved pattern on timber frame work complete including extra lowering charge and scaffolding charges as directed by Engineer-in- Charge.(Timber frame work to be paid separately).

Providing valley by using 20 gauge plain Aluminium sheet or equivalent quality with necessary overlaps at ends,with necessary steel nails ,eve plate etc including necessary scaffolding complete as per the instruction of engineer in Charge

Labour charge for Laying available departmental MP hip and ridge tiles set in lime mortar (1: 1/2:8) including finishing edges using red oxide powder etc. including necessary scaffolding complete as per the instruction of engineer in charge.

Providing and laying MP hip and ridge tiles 1st class set in surki mortar (1: 1/2:8) including finishing edges, etc. complete as directed by Engineer-in-Charge.

FLOORING WORKS

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge :Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III)derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Providing and applying flooring with white cement/cement plaster 1:3 (1cement and 3 fine sand) 15mm thick in two coats including a flushing coat of cement @ 2.2 kg/SQM)including mixing of approved quality red/black oxide powder (as per manufactures specification or Engineers direction) .including cost and conveyance of all materials,labour, curing, etc.as directed by the Engineer-in-charge at all levels.

Supplying and fixing 40 mm thick two line dressed Saderhally grey granite stone of size 300x300mm over a layer of 6mm aggregate 75mm thick. The 20mm wide joints shall be filled with PCC 1:1.5:3 using 6mm aggregates and finished with ruled pointing using CM 1:3. The edges of granite shall be 10-15mm machine cut from top and bottom side and the rest area shall be dressed vertically .The rate shall include labour charges for granite fixing and cutting to size,stone dressing charges , cost and conveyance of all materials,lead, lift, etc. complete as per drawings and as directed the Engineer-in Charge at all levels.(The sample shall be approved by the Architect)

Providing and laying decorated basement (Height of basement 72 cm, top width 48 cm) in traditional style with "Panchavarga", using good quality of black granite with hand dressed 2 line finish jointed with lime mortar as per the instruction of Engineer in charge and standard practice followed traditionally.

Providing and fixing single black granite Stone pillar of required size with hand dressed 2 line finish with all decorative works specified therein using hard granite stone as per the instruction of Engineer-in-charge

Providing and laying "Talakkallu"- unpolished granite stone slabs of minimum thickness 7.5 cm handdressed 2 line finish , for flooring inside Balikkalpura and around as the plinth Protection as per the instruction of Engineer-in charge

Providing and laying "Shobanam"- Hand dressed granite stone of size 1.2m x 0.23m x 0.72m with 2 line dressed finish with carving , for Side of the steps as per the instruction of Engineer-in charge

Providing and laying stone masonry with Hand dressed finished stone of 240mm thick , for above the floor level using good quality of black granite with hand dressed 2 line finish jointed with lime mortar as per the instruction of Engineer in charge and standard practice followed traditionally.

Providing and laying pressed clay tiles (as per approved pattern 14 mm nominal thickness of approved size) on floors jointed with white cement mortar 1:4 (1 white cement : 4 coarse sand) mixed with pigment to match the shade of tile , laid over a bed of 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including machine rubbing and floor polishing complete as per the direction of engineering in charge.

Supplying and paving 50 mm thick natural stone hand or chisel cut dressed well on top for paving in floor of walkway laid over 50mm thick compacted bed of sand etc to complete as per the direction of engineer in charge. Size of Stone 60cm x 60cm

Renovating lawns including weeding, cheeling the grass, forking the ground, top dressing with sludge or manure, mixing the same with forked soil, watering and maintaining the lawn for 30 days or more till the grass forms a thick lawn free from weeds and fit for mowing and disposal of rubbish as directed, including supplying good earth if needed but excluding the cost of sludge or manure (the good earth shall be paid for separately).

FINISHING WORKS

Plastering with lime mortar 1:2:9,(1cement:2 lime:9 fine sand )12mm thick using lime mortar and adequate quantity of herbals such as Jaggery, kadukka water and etc for old surface for traditional works including cost and conveyance of all materials, labour,scaffolding, curing, lead lift , etc complete at all levels and as directed by Engineer-in-charge.

Filling the major cracks by providing and applying approved products like Asian Paints-Smartcare Hybrid PU Sealant in proportion recommended by the manufacturer into cracks/honey-comb area of concrete/masonry by suitable method including cutting of nipples after curing etc. complete as per directions of Engineerin Charge.

Removing Rust using Rustolin or Equivalent at all locations by applying as per manufacturer's specifications and cleaning thoroughly etc complete On steel work

Aplying Sealer compound in new and old wood work after Preparing the surface/cracks with suitable wooden fillets(Saw dust mixed with fevicol or equivalent where ever required) then smoothing the entire surface and grooves with special chisel/tools without disturbing all wooden details and curving finally sand papering smoothly.The prepared surface has to be approved by the consultant before applying final coat.Then the entire surface will be applied with three or more coat of sealer compound in four hours intervals to obtain a uniform finish and visible of wooden grains (MRF, sheenlac)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :One or more coats on old work

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work

Applying white or colour wash by mixing glue & indigo as per requirement three or more coats to surfaces such as walls,columns, ceiling etc, after scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete including cost and conveyance of all materials, labour, scaffolding etc. complete as directed by Engineer-in-charge. Preparation of lime may be as per standard specification and test certificate of lime may be produced by the agency

Applying sealer compound in the new and old wood work like rafter, purlin, wall plates and other roofing members upto 10m height with minimal preparation.Clean the surface using a broom to remove dirt, dust and loose debris.Cracks with suitable wooden fillets ( saw dust mixed with fevicol or equivalent where ever required). Lightly sand only rough or splintered areas as needed.The entire surface will be applied with two coats of sealer compound in four hours intervals to obtain a uniform finish and visible of wooden grains ( MRF/ Sheenlac)

RCC WORKS

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size derived from natural sources)

Reinforced cement concrete work in beams, suspended floors, roofs, having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand (Zone III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo - Mechanically Treated bars of grade Fe-500D or more

Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:1½:3 (1 Cement: 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

STEEL WORKS

Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings/ wooden frames with rawl plugs screws etc

MISCELLANEOUS WORKS

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.All kinds of soil

Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

Providing and fixing double scaffolding system (cup lock type) on the exterior side, upto seven story hight made with 40 mm dia. M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staricase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after. The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required location with essential safety features for the workmen etc. complete as per directions and approval of Engineer- in Charge. The elevational area of the scaffolding shall be measured for payment purpose. The payment will be made once irrespective of duration of scaffolding. Note:- This item to be used for maintenance work judicially, necessary deduction for scaffolding in the existing item to be done .

Supplying and laying good quality red earth from approved source, spreading & compacting to fill up and level including watering and thorough consolidation to the standards and instruction of the engineer in charge.The rate Includes cost of materials conveyance, stacking charge, spreading, watering and consoldation as per the direction of Engineeer in charge

Supplying chemical emulsion in sealed containers including delivery as specified. BiFlex TC

Diluting and injecting chemical emulsion for POSTCONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :Along the external wall below

Providing anti-termite treatment to the useable members of wooden doors, windows and reapers, beams and rafters of roof ceiling etc. with two coat Biflex TC chemical diluted with kerosene or Turpentine after properly cleaning the wooden members etc complete conforming to manufacturer's specifications and as directed by the Engineer-in-charge.

Removal of tree growth from walls and floors of the building by using a chemical mix combination as specified.Phenol=250gms,Sodium Hydroxide=250gms,Caseine=200gms,Arsenic Trioxide=500gms.These chemicals are to be mixed thoroughly and applied to the roots of the trees and wait for a period of three months to ensure that the trees has died and shrunk and make good the damaged portions.complete as per the instruction of Engineer in charge.

Protecting timber by fungicide treatment by brush application of a 5% solution in white spirit of Biotin R and let set for one week.Gentle removal by brush of the accretions and dead micro vegetations .Impregnation by brush application of wood worm destroyer Perxil 10 on the entire surface and injectedd in the core by drilling 2mm holes if required,to reach all the infested portions.Consolidation by brush application of Rexil till rejection,dilute it till 50% if it remain visible but leave the surface dry removing all the excess of Rexil and let set for 1 day.

Trimming the tree branches shading to the existing building top upto 15m height by manual/mechanical means with necessary precautions and safety measures including stacking of servicable materials and disposal of unserviceable materials within a lead of 150 m

ELECTRICAL

POINT WIRING

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group C

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Group C

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 X 1.5 sq.mm

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 2.5 sq. mm

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 4 sq. mm

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.32 mm

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.50 mm

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.15/16 amp switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 amp socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.6 pin 15/16 amp socket outlet

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.3 Module (100mmX75mm)

Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.

MCCB, MCB AND DBS

Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required4 way (8+12) - three phase double cover (IP 42/43)

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer ) as required .(Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)4 WAY(4+12), DOUBLE DOOR

Supplying and fixing 5A to 32 A rating, 240/415 volts, 10 kA, ""C"" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Supplying and fixing 5A to 32 A rating, 240/415 volts, 10 kA, ""C"" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Triple pole

Supplying and fixing 6A to 32A rating, 240/415 V, 10 kA, C curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Four pole

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 milli Amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 25 amps

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 milli Amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

LT CABLE SUPPLY, LAYING AND TERMINATION

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.Upto 35 sq. mm (clamped with 1mm thick saddle)

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.Upto 35 sq. mm

Supply of one number PVC insulated and PVC sheathed / XLPE armoured Aluminium power cable of 1.1 KV grade of following sizes as required. 4C 10 sqmm XLPE Cable

"Supply of one number PVC insulated and PVC sheathed / XLPE armoured Copper power cable of 1.1 KV grade of following sizes as required. 3C 1.5 sqmm XLPE Cable

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 10 sq. mm (25mm)

Supplying and making end termination with brass compression gland and copper lugs for following size of PVC insulated and PVC sheathed / XLPE copper conductor cable of 1.1 KV grade as required.3C 1.5 sqmm XLPE Cable

Supply & laying of DWC pipe in ordinary soil 0.75m below ground level including excavation50/38 mm or nearest size

Supplying, laying and jointing of the following sizes of double wall corrugated (DWC) pipes made out of HDPE conforming to IS 14930 Part II for mechanical protection to underground power cables with all required accessories in ground in the existing trench50/38 mm or nearest size

Supply and fixing of thermoplastic polycarbonate cable junction box IP66/67 in accordance with IEC60529 environment friendly, recyclable, UV resistant, halogen & silicon free, anti acid & anti corrosive, shockproof with 5 pole terminals suitable to terminate upto 2.5sqmm

Supply and making end termination of 3core 1.5/2.5 sq mm unarmoured copper cable with (IP68) thermoplastic polyamide cable gland with appropriate size lock nut including all accessories as required.

EARTHING

Earthing with G.I. earth pipe 3 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (but with charcoal/ coke and salt) as required.

Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required 3.15 mm copper conductor (10 SWG)

Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.3.15 mm (10 SWG)

CABLE TRAY

Supply and fabrication of Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer and finishing with Epoxy paint (two or more coats) at all locations prepared and applied using structural steel etc. as required, all complete.

LIGHT FIXTURES AND FANS

Supply of 22±2W surface mounted LED tube light fixture, 4000K-5700K colour temperature, minimum 100 lumen/Watt, working on 240V AC etc as required. Make: Philips- Smartbright or equivalent.

Supply, installation, testing and commissioning of 8+/-2W decorative type Hanging light fixture, with lantern and chain made of black colour shockproof resin material body and transparent plastic( pmma) diffuser, with a colour temperature of 4000K with E27 Holder and lamp is with UV-rays stablized, rust and corosion free suitable for outdoor applications etc. as required. Make -Fumagali Sichem Cefa or equivalent

Supply of 8+/-2W wall mounted decorative light fixture (IP55) made of shockproof resin material, UV-rays stabilized, rust and corrosion-free, 2700-4000K colour temperature, with minimum 100 lumen/Watt, working on 240V AC, E27 base ,suitable for outdoor applications, including 9W LED bulb and all connections etc. as required. Make: Fumagalli- Bisso Cefa or equivalent.

Supply, installation, testing and commissioning of LED light with profile (IP54), 9W/m, 3000K colour temperature, including all connections etc as required. Make: Hybec or equivalent.

Supply, installation, testing and commissioning of 8±2W LED Bollard light fixture (IP 55) of body height 0.8metre have black finished body and opal diffuser, 3000K colour temperature , E27 base suitable for outdoor applications, including all connections etc. as required. Make: Fumagalli Amelia or equivalent

Supply, installation, testing and commissioning of LED drive of 60W Input Voltage: 200-250VAC Output Voltage: 12V or 24V IP rating :IP20 including all connections etc. as required.

Supply of 1200mm sweep ceiling fan complete with 300mm down rod , canopies, shackles and blades, excluding resistance type regulator working on 230V/240V single phase AC. Make : Crompton or equivalent

Installation, testing and commissioning of pre - wired, fluorescent fitting/ compact fluorescent fitting of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq.mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

Conveyance installation testing and commissioning ceiling fan of all sizes using standard accessories excluding resistance type regulator wiring the down rod with 16/0.20mm PVC insulated and PVC sheathed 650/1100V grade 3 core round copper conductor flex wire or extending the original wiring etc. as required.

Supplying and fixing extra down rod of 10 cm length G.I. pipe, 15 mm dia, heavy gauge including painting etc. as required. (Note: More than 5 cm length shall be rounded to the nearest 10 cm and 5 cm or less shall be ignored)

Supply and installation of suitable size MS rod type fan clamp in the RCC slab as per IS 732 as required.

Numbering of ceiling fan / exhaust fan/ fluorescent fittings as required.

PANEL BOARD

Supply, installation, testing and commissioning of following wall mounting, indoor meter panel suitable for operation on 3 phase and neutral, 415 V, 50Hz AC system including fixing it and making good the damages etc. as required. Meter Panel Incomer: 63A TPN Isolator - 1 no 40A Cut Out Fuse - 3 Nos. Provision for fixing 3Phase 4Wire 10-63A direct energy meter - 1Nos Provision for fixing FP RCCB- 1 Nos Busbar: Al busbar suitable for 63A

MISCELLANEOUS WORKS

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

DISMANTLING

Dismantling carefully Electric supply lines and pipe fittings including stacking serviceable materials within 50 meter lead as directed by Engineer in charge

DOCUMENT APPROVAL

Preparation of all drawings, submitting and getting approval arranging inspection from KSEB, obtaining power allocation and permanent power connection etc and commissioning of the additional installation in the premises. All statutory payments will be reimbursed on production of the original receipts

CCTV SURVILLENCE SYSTEM

Supplying and drawn of UTP 4 pair CAT 6 LAN cable in the existing surface/recessed steel/PVC conduit as required1 run of Cable

Supply and laying of Outdoor Cat 6 UTP Cable through exisiting conduits

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.32 mm

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.1 or 2 Module (75mmX75mm)

Supply & Fixing the following types/ sizes of boxes suitable for modular accessories in surface/ recess including making good the damages, colour washing etc as required (RoHS compliant )2 module moulded plastic box on surface

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.1 or 2 Module

Supply and installation of Information Outlet Category 6 , RJ-45 Information Outlet with IDC Connector terminations Preferred Make: Molex/Commscope/Belden/Schneider/3c3

Supply and installation of Cat 6 RJ 45 Connectors with boot. Preferred Make: Molex/Commscope/Belden/Schneider/3c3

Supply and installation of 1 Meter Cat 6 UTP Patch Cord Preferred Make: Molex/Commscope/Belden/Schneider/3c3

Supply and installation of 2 Meter Cat 6 UTP Patch Cord Preferred Make: Molex/Commscope/Belden/Schneider/3c3

Supply and installation of Cat6 UTP , Patch Panel - 24 ports fully loaded patch panel with rear strain release bar. Preferred Make: Molex/Commscope/Belden/Schneider/3c3

Supply & Fixing the following types/ sizes of boxes suitable for modular accessories in surface/ recess including 3x3 or suitable size moulded plastic Camera Co box on surface

Supply and fixing of 4x4 Camera Co Box-Weather proof-IP66

Supply and installation of Ethernet PoE Surge protection device for camera.

Supply & Fixing of the Weatherproof Junction of Box with necessary accessories for Pole mounting for placing the Surge Protection Devices.

Supply,installation,testing and commissioning of GI pole of 6m height, 3 inch Diameter, Class B, Fixed in concrete footing with properly finished with painting as required,Pole drilling for cable entry,Base plate etc.

Supply and Installation of Pole Mounting Accessories for camera

Supplying and laying of following size DWC HDPE pipe lSI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 em below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc. , complete as required. 40 mm Size

Supply and installation of 15U rack with 550X500 Glass Door, Side Panels, 1 No of Horizontal shelfs, 2 No of Rack Air Circulation module, 1 No of Rack mountable Horizontal PDU, 2 No of Horizontal Cable Manager , Lock & Key and Mounting Accessories.

Supply and installation of 9U Outdoor Rack with 500X600 , Galvanized steel folded,wielded 19'' Out door Rack IP56 Rated with Power distribution unit 3Soc 5A 1Ph, One U Shelf one Number,Cooling fan with necessary mounting accessories.

Supply and installation of Layer 2 Managed 8 Port PoE switch with Minimum 2x1G SFP Port. Preferred Make: Cisco/Netgear/Allied Telsis/HP

Supply and installation of Layer 2 manageable PoE switch with Non blocking switch fabric having 24 Port 10/100/1000Mbps PoE & 2x1G SFP port. Three year warranty. Preferred Make: Cisco/Netgear/Allied Telsis/HP

Supply and installation of 1G Single Mode SFP Module

Supply and installation of 6 core Single Mode OS2 armoured fibre cable Preferred Make: Molex/Commscope/Belden/Schneider/3c3

Supply and installation of 6 port rack mountable LIU fully loaded with LC duplex adaptor, couplers, 1.5mtr SM OS2 LC pigtails, blank plates with rack mounting accessories. Preferred Make: Molex/Commscope/Belden/Schneider/3c3

Supply and installation of Fiber Optic Patch Cord LC-LC, Duplex, Single Mode, 3 metre Preferred Make: Molex/Commscope/Belden/Schneider/3c3

Splicing Charges

Supply of 4MP IP Dome Camera, 2.8mm or optional fixed lens , H.265 /H.264 encoding, Day/Night(ICR), DWDR, IR LEDs Length 30m or higher Ip66, PoE. Preferred Make: Dahua/UNV/CP-Plus/Matrix/Hikvision

Supply of 4MP IP Bullet Camera, 3.6mm or optional fixed lens , H.265 /H.264 encoding, Day/Night (ICR), 120WDR, IR LEDs Length 30m, Onvif, IP66 or Higher, PoE. Preferred Make: Dahua/UNV/CP-Plus/Matrix/Hikvision

Supply of 32 Channel NVR support upto 8MP at 160 Mbps incoming bandwidth or higher , Supports 4K, 4 HDD SATA supports upto 8TB each , HDMI,VGA support, H264/H.265 Compression, Onvif profile. Preferred Make: Dahua/UNV/CP-Plus/Matrix/Hikvision

Supply and installation of 6 TB Surveillance hard disk Preferred Make: WD/Toshiba/Seagate

Supply and installation of Wireless Mouse

Supply Installation Testing and Commissioning of 32-inch TV with LED-backlighted LCD screen, Including HDMI, USB, LAN, WIFI connectivity, and mounting accessories.

Supply and Installation of 5 Meter HDMI Cable

PA SYSTEM

Supply and Installation of 30W Horn Speaker with Frequency Response 250 Hz - 10 kHz,Sound Pressure Level 113 dB. Preferred Make: Toa/Bosch/Equivalent

Supply and Installation of 240W Mixer Amplifier with Frequency Response 50 20,000 Hz,Signal to Noise Ratio Over 60 dB. Preferred Make: Toa/Bosch/Equivalent

Supply and Installation of Table top Microphone with frequency response 50Hz 16kHz,Sensitivity –41dB ±3 dB,Impedance 750, balanced. Preferred Make: Toa/Bosch/Equivalent

Supply and Installation of 2Cx 1.5 Sqmm Armoured Speaker Cable

FIRE PROTECTION SYSTEM

Supply, Installation, Testing & Commissioning of ABC Type Fire Extinguishers 6kg capacity. Make: Kanex/Safex/Equivalent