Providing LIS from River Beas to Village Tandoo Mehar Pakhari Dawardu and Bhatog in Tehsil Sadar Distt Mandi HP

Amount

Excavation in foundation and trenches etc. in earth work in all kind of soil such as pick work jumper work,saturated soil including bailing or pumping out water, blasting soft/hard rock, chiseling soft/hard rock where blasting is prohibited in all lifts including trimming and dressing of sides, levelling of bed, stacking the excavated soil clear from the edge of excavation and then returning the excavated soil in 15cm. layers including consolidating each deposited layer by ramming , watering and then disposing of all surplus excavated soil as directed in all leads/lifts and shoring strutting,timbering and dewatering where ever required as per direction of the Engineer-in-Charge.

Providing and laying cement concrete 1 : 2: 4 (1Cement : 2 Sand : 4 graded stone aggregate 20mm nominal size)and curing complete excluding cost of form work and re-inforcement for reinforced concrete work in

Suspended floor ,roofs, lendings and shalves and thier suports balconies, beem griders and bressumers and cantiliver upto floor two level with in all leads and lifts.

Providing and laying cement concrete 1: 3 : 6 (1Cement : 3 Sand : 6 graded stone aggregate 40mm nominal size) and curing complete excluding cost of form work in foundation and plinth with in all leads and lifts.

Providing and laying cement concrete 1:1.5:3 (1cement:1.5 sand : 3graded stone aggregate 20mm nominal size)and curing complete excluding cost of form work and re-inforcement for reinforced concrete work in:-

Wall (any thickness but not less than 0.1 m thickness) attached pillasters, buttresses, plinth and string courses, etc. from top of foundation level upto floor two level complete with in all leads and lifts as per direction of the Engineer-in-Charge.

Foundation , footing basis of columns & the like and mass concrete complete in all respect and as per the direction of Enginer-in-Charge

Columns, pillars, posts and struts upto floor to level.

Suspended floor ,roofs, lendings and shalves and thier suports balconies, beem griders and bressumers and cantiliver upto floor two level with in all leads and lifts.

Arches upto floor to level.

Random rubble masnory/ polygonal rubble masonry(uncoursed/brought to courses) with hard stone of apporved quailty in foundation &plinth including levelling up with cement concrete 1:6:12(1Cement :6 sand :12greded stone aggregate) in cement mortor 1:6 complete in all respect and as per the direction of Enginer-in-Charge

Providing and laying cement concrete 1:6:12 (1cement:6 sand:12 graded stone aggregate 40mm nominal size) and curing complete excluding cost of from work in foundation and plinth complete in all respect with in all leads and lift and as per the entire satisfaction of Engineer-in Charge.

Providing and laying cement concrete 1:5:10 (1Cement : 5 Sand : 10 graded stone aggregate 40 mm nominla size) with 15% plum and curing complete excluding cost of form work in retaining wall, the size of plum shall usually be 150 mm to 300 mm as per HPPWD specification with all leads and lifts.

Providing form work with steel plates3.15mm thick welded with Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm so as to give a fairfinish I/c centring , shuttering , strutting and proping etc.with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4m and removal of the same for insitu- reinforced concrete & plain concrete work in :-

Vartical surface such as walls (any thickness) portion and the like including attached pillers,buteress plinth and staircases and the like.

Flat surfaces such as soffits of suspended fioors roofs landing and the like . Floors etc up to 200mm in thickness.

In foundation, footings & Buttresses etc. in all leads and lifts

Beams ,cantilevers, girders and lintels up to floor to level with in all leads and lift.

Providing form work of ordinary timber plankings so as to give a rough finish including centering shuttering, propping etc. hight of propping and centering below supporting floor to ceiling not exceeding 4 metres and removal of the same for-in-situ reinforced concrete and plain concrete work in:- arches, domes, baults upto all span in all leads and lifts.

Providing tor steel reinforcement for reinforced cement concrete work including bending, binding in position complete upto floor two level complete in all respect and as per the direction of Engineer-in-Charge

Providing and fixing M.S. Foot rest with in all leads and lift.

Providing 40x3 mm flate iron hold fast 40 CM long including fixing to frame with 10 mm dia meters bolts and nuts and wooden plug and ambeding in cement concrete block 30x10x15 (1:3:6 1: cement 3: sand 6: graded stone aggregate 20 mm nominal size ) as per direction of the Engineer-in-Charge.

Steel work welded in built up sections,trusses and framed work including cutting,hoisting, fixing in position and applying a priming coat of red lead paint in all leads and lifts.

Providing of chain hoist (chain pully) of 5 MT capacity confirming to IS:3832-1987 with grade 80 alloy steel lead chain testing to 25% over load with 3 mtrs. Chain lift operated with in and down batrope on pannel with cord of reputed make like indef/deep, white horse /load mate as per specification /ISI marked complete in all respect with carriage in all leads and lifts and to the entire satisfaction of Engineer-in-Charge.

Laying, jointing, testing in trenches and carriage of GMS tubes (light grade) including tube fittings (earth work to be measured and paid for separately) complete in all respect in all lead and lifts.

a) 150 mm dia

Providing and Fixing Cast Iron Sluice Valve ( with hand wheel) as per IS: 780-1984 class-1 upto 300 mm dia including brass spindle and as per 2906-1984 class-II for dia more than 300 mm complete with Nuts & Bolts rubber in sertion etc.complete in all leads and lifts and to the entire satisfaction of the Engineer-in-Charge in all leads and lifts.

150 mm diameter

Providing and fixing tube settler media with in all leads and lifts.

Providing in RCC work smooth finishing of the exposed surface with cement mortor 1 : 3 ( 1 : cement 3 : sand ) with in all leads and lift.

Constructing chamber for sluice valve with CI surface box 100 mm top dia, 160mm bottom dia and 180 mm deep (inside with chained lid RCC top 1:2:4 mix (1 : cement 2: sand 4: graded stone aggrigate 20 mm nominal size) 100 mm thick foundation concrete 1:5:10 mix (1: cement 5: sand 10: graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortor 1:3 ( 1:cement 3: sand ) finished with a floating cost of neat cement including curing complete 600x600x750 mm inside size with 150 mm thick wall of RCC 1:2:4 (1:cement 2: sand 4: graded stone aggregate 20 mm nominal size) complete with form work and rainforcement with 6 mm bars at not exceeding 150 mm centres both ways with in all leads and lifts.

Providing and fixing manhole cover of size 60x60 cm made of angle iron frame size 40x40x5 mm thick covered with MS sheet 2.00 mm thick and welded with angle iron frame 35x35x3 mm thick including hings, handle, 8 Nos. hold fast and locking arrangement alongwith lock and key of standered make, primer two coat with redoxide paint, complete and mainhole cover fixed in storage tank/intake with cement concrete 1:1.5:3 for nut and bolt 16 mm dia and dismentalling of RCC work nad as per direction of Engineer-in-Charge.

Providing MS railing along centilever slab around the dome with in all leads and lifts.

Boulder filling behind retaining wall within all leads and lifts.

Sand filling under floor including watering ramming consolidating and dressing complete, as per direction to the entire satisfaction of Engineer-in-Charge.

Brick work using common burnt clay building bricks in foundation and plinth in cement mortar 1:6 ( 1 Cement : 6 Sand ) second class bricks with in all leads and lifts.

Half brick masonry in common brunt clay building bricks in cement mortar 1 :4 ( 1 Cement : 4 Sand ) second class bricks with in all leads and lifts.

Providing plinth protection 50mm thick in cement concrete 1:3:6 (1 cement :3sand: 6 graded stone aggregate 20mm nominal size) including finishing the top surface of concrete smooth complete in all respect and as per direction of Engineer-in-Charge.

Supply and fixing rolling shutter of approved make made of 80 mmx1.25mm MS laths interlocked together through their entire plinth and joint together at the end by hand locks mounted on specially designed pipe shaft, with brackets side guides and arrangements for inside and outside licking with push pull operation complete including the cost of the top cover and spring with in all leads and lifts.

Providing and fixing anodised alluminium work for doors, windows and ventilations with in all leads and lifts.

Providing and fixing anodised alluminium shutters for doors, windows and ventilations with in all leads and lifts.

Providing and fixing wire gauge shutters using anodised alluminium of IS gage designation 85 G with wire of dia 0.56 mm for doors, windows and clerestrey windows including bright finished black enameled iron hinges with necessary screws with in all leads and lifts.

Providing 40x3 mm flate hold fast 40 CM long including fixing to frame with 10 mm dia meters bolts and nuts and wooden plug and imbeding in cement concrete block 30x10x15 ( 1: 3: 6 1: ecment 3: sand 6; graded stone aggregate 20 mm nominal size) as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing & fixing M.S. grils of required pattern in wooden frame of window etc. with M.S. flats square or round barswith round headedbolts and nuts by screws plan grils complete in all respect and as per the direction of Engineer-in-charge

Providing and fixing Oxidized M S Handlewith necessary srews etc complete in all respect and as per direction of Engineer-in-Charge.

Providing and fixing anodised M.S. Tower bolts (Barrel type) with necessary screws etc.complete in all respect and as per direction of Engineer-in-charge..

Providing and fixing oxidized M.S. sliding door bolts with nuts and screws etc. complete 300x16 mm

6mm cement plaster to ceiling in cement mortar 1:3 (1cement:3sand) complete in all respect and as per the direction of Engineer-in-charge.

15 mm cement plaster in single coat on rough side of brick / concrete / stone walls for interior plastering upto floor two level including arrises internal rounded angles, chamfers and or rounded angles not exceeding 80 mm in girth and finished even and smooth in cement mortor 1 : 3 (1 Cement : 3 Sand) with in all leads and lifts.

20 mm cement plaster in single coat on rough side of brick/ concrete / stone walls for interior plastering upto floor two level including arrises internal rounded angles, chamfers and or rounded angles not exceeding 80mm in girth and finished even and smooth in cement mortor 1 : 6 (1 Cement :6 Sand) with in all leads and lifts.

White glazed tiles 6 mm thick in flooring cement mortar 1 : 3 (1 Cement : 3 Sand) finished with flush pointing in white cement all leads and lifts and to the entire satisfaction of the Engineer-in-Charge.

Providing and fixing 0.60 mm thick prepainted steel sheet in roofing with hot dipped metailic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 micron over 5 micron primer coating to back coat of polyster of 5 micron over 5 micron primer coating i/c fixing with prepainted iron J or L-hooks, bolts and nuts 6 mm dia meters with prepainted limpet rubber washers complete in all accessories as per direction of the Engineer-in-Charge.

Providing ridges or hips 60 cm over all in plain GI sheet with galvanised iron J or L hocks bolts and nuts 8 mm dia GI limpet and bitumen wash here complete:- 0.63 mm thick sheet with in all leads and lifts.

Applying priming coat on new steel and steel based surfaces after and including preparing the surface by thoroughly cleaning oil, grease, dirt,and other foreign matter , sand papering and knotting ready mixed paint brushing wood primer pink complete in all respect and as per direction of Engineer-in-charge.

Painting two coats ( excluding priming coat ) on new wood and wood based surfaces with enamel paint to give even shade including cleaning the surface of dust and other foreign matter, sand preparing and stopping with enamel paint other than white complete in all respect and as per direction of Engineer-in-charge.

White washing with lime on un-decorated wall surfaces (with two coats) to give an even shade including thoroughty brooming the surface to remove all dirt,dust,mortor dirt and other foreign mattercomplete in all respect and as per direction of Engineer-in-charge

Providing and fixing flood light in all accessories complete with in all leads and lifts as per entire satisfaction of Engineer-in-Charge.

Providing and fixing 5 Ton chain pully /gantry of approved ISI make electrically operated alongwith all allied accessories complete with in all leads and lifts as per entire satisfaction of Engineer-in-Charge.

Providing and fixing power blocks in 250 sqmts with in all leads and lifts as per direction of Engineer-in-Charge

Providing wood work in frames of door and windows and clerestory windows complete in all respect 2nd class DD Wood.

Providing and fixing panneled glazed or panneled and glazed shutters for doors, windows and clerestory windows, including black enamelled iron butt hinges with necessary screws 40 mm thick 2nd class deodar wood complete in all respect and as per the direction of Engineer-in-Charge

Distempering with oil bond distemper of approved brand and manufacture (two coats) and of required shade on undecorated wall surfaces to give an even shade sand papered smooth.

Providing and fixing automatic flushing cistern with a pair of C.I. or M.S. brackets complete with fittings including C.I. syphonic apparatus mosquito proof lid, C.P. brass unions and coupling for connections with inlet, outlet and overflow pipes including cutting holes and making good the same (overflow pipe to be measured and paid for separately) vitreous China 5 litres capacity with in all leads and lifts and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing vitreous China wash down, water closet (European type, W.C. pan) with integral "P" or "S" trap including jointing the trap with soil pipe in cement mortar 1 : 1 (1 Cement : 1 Sand) (Seat and cover to be measured and paid for separately) white colour with in all leads and lifts and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing 100 mm size P or S trap for water closet (Squatting Pan) including jointing the trap with the pan and soil pipe in cement mortar 1 : 1 (1 Cement : 1 Sand) sand cast iron with in all leads and lifts.

Providing and fixing viterous china wash basin with single hole for pillar tap with CI or MS bracket painted white including cutting hole including good the same excluding fitting Cera sanitary work (cornet) white 550x400 white with in all leads and lifts.

Providing and fixing viterous china padestral for wash basin complete recessed at the basic for reception of pipe and fittings Cera sanitary work (carnet) white (viterous China in white colour) with in all leads and lifts

Providing and fixing of water storage tank sintex having of capacity 500 litres with necessary fittings including over flow pipes, scour pipes etc. inlet and outlet and inside paint of required size for inlet or outlet and inside paint of approved quality complete including hoisting complete in all respect with in all leads and lifts.

Providing and fixing on wall face PVC (D-Plast) rain water pipes of working pressure not less than 4.5 Kg/Sqcm including fitting the joints with approved adhesive complete with in all leads, lifts and carriage of materials 110 mm nominal bore within all leads and lifts.

Providing and fixing on wall faces PVC door bend (D-Plast) with oval access door, insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including fixing with approved adhesive complete 75 mm nominal bore within all leads and lifts.

Providing and Fixing to wall ceiling and floor galvanised mild steel tubes (Medium grade) tube fittings and clamp including making good the wall ceiling and floor in all leads and lifts 15 mm nominal bore.

Providing and fixing Gun Metal full way wheel valve 15 mm dia with in all leads and lifts.

Providing and fixing C.I. Cow 100 mm dia with in all leads and lifts.

Providing and fixing brass bib tap (Superior quality or heavy type) 15 mm dia with in all leads and lifts.

Providing and fixing CP brass soap dish with CP brackets fixed to wooden plugs with CP brass screws complete in all respect in all leads and lifts.

Wiring for light point / fan point / exhaust fan / call bell point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in PVC casing & capping and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required.

Group C.

Wiring for circuit / sub-main with following size PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in PVC casing & capping along with 1 No.HRFRLS/PVC insulated single core copper conductor cable of same size for earthing as required.

2 x 1.50 Sq. mm.

2 x 2.50 Sq. mm.

a) Supplying and fixing 3 pin 5/6 amps. Socket outlet on the exists switch box/covers including connections etc. as required.

Supplying and fixing 2 way 5/6 amps. Tumbler/piano type switch on the existing switch box on the switch box/cover including connections etc. as required.

a) Supplying and fixing 3 pin 15/16 amps. Socket outlet on the exists switch box/covers including connections etc. as required.

Supplying and fixing 15/16 amps. Tumbler/piano type switch on the existing switch box on the switch box/cover including connections etc. as required.

Supplying and fixing wooden box of following size (nominal) on surface or recess with suitable size of phenolic laminated sheet cover of in front as required.

229 mm.x 102 mm.x 60 mm. deep

203 mm.x152 mm.x 60 mm. deep

Providing and fixing of CFL 1x23 watt of reputed make in all leads and lifts.

Providing and fixing of CFL 1x5 watt of reputed make in all leads and lifts.

Supplying and Fixing 5 Amps to 32 Amps rating, 240 Volts, L series miniature circuit breaker of following poles in the existing MCBDB complete with connections, testing and commissioning etc. as required Cat - A. (Single Pole)

AMIT CHOUDHARY

Vijay kumar kushwaha