Incinerator

For Supply, Installation, Testing & Commissioning Nowaste Fuel Free Incinerator With Emission Control Device (Model-STNW-100ECD)

COMBUSTION CHAMBER-PRIMARY

Material: Boiler Grade Steel Plate Thermal Insulation : A)Inner phase:IS:8 Grade Premium Quality Fire Bricks&Ceramic clay B) Outer Phase:With 50mm Thick Glass wool C)Protected With 0.7mm Thick Aluminum Sheet Dimension: Dia 1200mm, Height:1250mm,Thickness 4mm.(Cylindrical part).Upper and Bottom conical area thickness 6mm and 4mm Erection : Erected upon four leegs made of high quality TATA Stel pipe of dia.76mm and thickness 4mm at 600mm from ground level. Other Features: waste loadingdoor,cleaning door,Acss ladder,peep hole,Ash chamber with door. Volume : 1cubic meter/35CFT Capacity : per day 1MT/10 Hours Efficiency : 99.3% Fuel Consumption: for Incinrator is Nil For wet scrubber system-Full day Power supply to run a 1HP Pump Dry wet Ratio: 2:1(60% Dry and 40% wet garbage)

SECONDARY CHAMBER

Secondary burning with the help of additional air inlet tubes Material : MS Pipe Dimension : Dia.458mm, Height: 3000mm, Thicknss:10mm Thermal Insulation: Tri-cast ceramic clay Coating,Thickness:50mm

EMISSION CONTROL SYSTEM

ECD is an air Pollution control devices that are used to remove particulate matter from flue gas. Emission Control Device: wet scrubbing system water consumption: 60 Ltrs/Day

CHIMNEY

Material : Seamless Carbon Steel Pipe Dimension: Dia.254mm,Thick:8mm Additional Features: 1.Port hole and access ladder for routine maintenance and emission tests 2.Speecially designd diffuseer prevents rain water entering the chamber

Fountation Footing

Earthwork excavating and depositing on bank with an initial lead of 10m & initial lift of 2m in hard stiff clay, stiff black cotton, hard red earth shales, muram, graverl stoney earth & earth mixed with small size boulders & hard gravelly soil as per S.S 20B as Per Standard Specification.

Plain Cement Concrete 1:4:8 Mix (one part cement, Four part sand and Eight part of aggrigate) using 40mm size ISS HBG metal machine crushed from approved quarry including cost and conveyance of all materials to site, loading and unloading charges and labour charges for mixing, laying and curing etc. complete. Complying with std. specifications.as Per Standard Specification.

Supplying and erecting centering for sides and soffits including supports and strutting upto 3.00m height for plane surface such as RCC Slab, Rectangular Beams, Tee (or) ELL Beams, Lintel Bed Block, Slabs, Landing Slabs, Beams Canopy, Side Slab (or) Square (or) Round columns etc., as detailed below with all cross branching using M.S. Sheets of size 80cm x 60cm and B.G. 10 stiffended with welded M.S. Angles of size 25 x 25 x 3mm for boarding laid over silver oak or country wood joints of 10cm to 30cm to dia spaced at 75cm c/c etc., complete complying with standard specifications as directed by departmental officers etc., complete.as Per Standard Specification.

Plain Cement Concrete 1:2:4 (One Cement, Two sand and Four broken stone jelly) using 40mm size hard broken stone jelly for dummy columns, excluding cost of centering shuttering reinforcement grills and fabrication charges but including curing etc. complete. (Reinforced Cement Concrete 1:2:4 for slab to be extended upto top of splashing with pressed tiles and future extension rods to be embedded in CC 1:2:4 (One Cement, Two sand and Four broken stone jelly). Dummy columns should be at least 1 metre height)

Supply and fabrication of steel using TMT rods for all Reinforced cement concrete works including cost and conveyance of all materials and all labour charges for cutting, bending and placing the rod in position and tying up the rods with binding wire and other incidental charges etc., complete. as per standard specification SS 86 & 86A V,VI, VII (S6) 7,3

Please Enable Macros to View BoQ information