SPL REPAIR TO BLDG NO P 24 DWARKA VIHAR AND PROVN OF CATTLE FENCING AT MIL STN GANDHINAGAR

Amount

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc. complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exc. 15cm thickness (below or above ground level) all as specified and directed.

Demolition of reinforced cement concrete of any description etc complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and directed

Taking down cement plaster on brick or stone wall etc. including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed.

Excavation in trenches n exc 1.5m wide and n,exc 1.5 m in depth for foundation,etc or shafts, wells, cessipts,manholes,pier holes,etc n exc 10 sq m inplan and getting out in soft/loose soil.

M&L M S steel gate, of angle or other section with gusset plates ,rails comforming to Fe-41--W (Gde-E-250) including for hanging or sliding with and including either hooks and hinges with locking arrangements, (2.30m wide and 2.00 High) etc completed all as specified and as directed.

Excavation of post holes (or similar holes) each not execeeding 0.5cum and getting out in soft/loose soil returning filling in and ramming earth of broken rubble mixes with earth around in layers complete all as specified and directed.

M&L PCC (1:4:8) C-2 using 40mm graded stone aggregate as in foundation filling and mass concrete as in foundation filling and mass concrete all as completed as directed.

M&L Reinforced cement concrete (1:2:4) type B-1 (uing 20mm graded stone aggregate) in precast posts, fencing posts,straining or terminal posts, struts etc for fencing average sectional area exc 100 and n exc 250 sq cm, with or wittout chamferd angles and flat, splayed, rounded or mitred tops as directed and fixed.etc completd all as specified and directed.

M&L Preperation of new steel surfaces over 10cm or girth and applying two coats of synthetic enemalled paint over a coat of red oxide zing chrome primer etc complete all as specified and as directed.

Removing excvaated soil nexc 50m and depositing where directed at a level n exc 1.5 m above the stating point soil etc completed all as specified and as directed.

M&L Galvanished, 2 strand,steel barbed wire 2.24mm dia barbed with 2mm barvs dia barbs at 75mm spacinges and straining and fixing to any type of standard rails strin-ing bolts including secuting or tying at crossinges with and provision of galvanished mild steel wire stapples or steel pins,etc complected all as directd and as specified (Note : Each raw of wire to be measurede)

M&L for fly ash Brick work with old size, sub class 'B' bricks, straight or curved on plan exc. 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

Cutting chases, pinning in, for brick walls, making good to facings for concealed water tubing etc. cutting exceeding 10cm but not exceeding 20cm girth complete all as specified and directed.

Taking down steel window/ventilator including grills of any description, n. exc 1.5 Sqm each complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 sqm each complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutter from the frames) exc. 1.5 sq.m but not exc. 4 sq.m each complete all as specified and directed.

Taking down old shutters of any description exc. 1 sqm but not exc. 2 sqm each complete all as specified and directed.

Resecuring or easing & adusting without taking down of shutters exc 1.0sqm and n.exc 2.0sqm and adjusting with out taking down

S&F, in repair, pre-painted galvalume aluminium zinc coating GI based plain steel sheet, 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F, powder coated Aluminium windows/ ventilators with one or more rebates including joining cleat for fixing etc complete with frames, shutters and grills of size directed by Engineer-in-charge including handles, tower bolts, grills, etc complete all as specified and directed. Note:- sheet glass, wire cloth, shall be measured and paid seperately.

S&F, factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site complete all as specified and directed.

S&F, solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, supplying and fixing in opening as per specifications complete all as specified and directed.

S&F, 35 mm thick, 2nd class hard wood, factory made, glazed & skeleton shutters, open rebated and prepared to receive glass, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. Sizes of members of shutters as specified in SSR Part I, Section 8, Clause 8.24 (a) complete all as specified and directed.

S&F, 35 mm thick 2nd class hard wood plain framed panelled shutter (two panel) with lock rail and panel of 12 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS 1003 (Part -I), Klin seasoned and chemically treated and complete all as specified and directed.

S&F, single action spring hinges (ISI MarK), mild steel with steel wire spring, stove enameled black, size of spring hinge 150mm all as specified and directed.

Supply & fixing 100 mm long Butt hinges, extrucded aluminium alloy with brass/bronze hinge pin, anodised type B-21 , bright polished type B-11.

S&F, butt hinges, medium weight, cold rolled, mild steel of size 100 mm complete all as specified and directed.

S&F, Mild steel barrel tower bolts, stove enameled black with bright bolt of 200 mm complete all as specified and directed

S&F in repair Mild steel barrel tower bolts, stove enameled black with bright bolt of 200 mm complete all as specified and directed

S&F, aluminium anodised, barrel tower bolts of extruded section with length of bolt 150 mm and fixed complete all as specified and directed

S&F 250 mm long mild steel sliding door bolts, enamelled black with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed.

S&F in repair 250 mm long mild steel sliding door bolts, enamelled black with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed.

S&F extruded aluminium alloy handles, fabricated type, anodised of size 125 mm complete all as specified and directed.

S&F Mild steel pressed handles,oval type stove enamelled black of size 125mm complete all as specified and directed.

S&F in repair Mild steel pressed handles,oval type stove enamelled black of size 125mm complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring fixed in floor of 150mm complete all as specified and directed.

S&F in repair floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring fixed in floor of 140mm complete all as specified and directed.

S&F, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F 4 mm thick, black tinted glass panes fixed to aluminium windows/vents with necessary rubber gaskets complete all as specified and directed.

S & F 3 mm thick figured sheet glass, ordinary quality and glazing not exceeding 0.5 Sqm in each pane fixed complete all as specified and directed.

M&L for cutting holes into or through brick walls built in cement mortar or cement lime mortar and making good in cement mortar 1:3 or cement concrete 1:2:4, type B-l as required, superficial area not exceeding 150 sq. cm including necessary scaffolding, if required complete all as specified and directed.

M&L Mild steel tmt bars10mm dia and over, cut to length, bend to shape required, including crancking, bending for hooplig for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc completed all as specified and as directed.

M&L 5 mm and over upto and including 10mm dia in stirripus, spacers and binders cut to length,bend to shape required including crancking, bending spirally for hooping for columns, hoocking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc completed all as specified and as directed.

M&L Rolled mild steel sections conforming to Gde Fe-410-0 or Fe-310-0 as in framing for cladding, glazing and the like including door frames/ chowkats, coolerstand etc fixed with angle cleats and connecting plates, etc complete all specified and directed.

S&F framed work such as grills, grating etc with ends of bars shoulderd or rivetted or forcged into spikes ,framed guard bars ,barred iron doors congirming to FE 290 Gde E-165 complete all as specified.

M&L 16 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.

Rounding to edges of stone slabs one edge, such as steps, cooking platform, and other similar situations complete all as specified and directed.

M&L for 25mm thick cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate as in flooring finished fair and even to receive floor finishes complete all as specified and directed.

M&L for 75mm thick cement concrete 1:3:6 type C1, using 40mm graded stone aggregate as in plinth protection, finishing cement concrete surfaces even and smooth without using extra cement, Joints of plinth protection shall be filled with bitumen mastic (1:3) complete all as specified and as directed.

M&L for cutting uneven surfaces of concrete & cutting reinforcement from drops of fins & facias (thickness not exceeding 50mm) using necessary scaffolding and making good the disturbed portion with 5mm thick rendering in CM 1:3 finished even and smooth without using extra cement etc. complete all as specifeid and directed.

M&L for non skid coloured tiles any colour 7 to 8 mm thick (square/ rectangular), area of each tile exceeding 0.11 Sqm and not exceeding 0.18 Sqm each in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match tiles, over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L for non skid coloured tiles any colour 7 to 8 mm thick (square/ rectangular), area of each tile exceeding 0.11 Sqm and not exceeding 0.18 Sqm each as in vertical surfaces such as skirting/ dado over set and jointed in neat cement slurry and pointed in coloured cement to match tiles, and including rendering 10 mm thick in CM (1:4) compelete.

M&L for glazed ceramic coloured tiles any coloured / shed of size 450mm x 300mm x 6 to 7mm on vertical surface such as skirting, dados, risers to steps etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, laid over and including rendering 10mm thick in cement mortar (1:4) , complete all as specified and directed.

M&L for rendering cement plaster 10mm thick in cement mortar (1:6) on brick work or concrete surfaces of walls, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering cement plaster 12mm thick in cement mortar (1:4) on brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering cement plaster 5mm thick in cement mortar 1:3 on fair faces of concrete in ceilings, chajjas, fins facia etc. finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of old decorated plastered or unplastered ceiling surfaces including brooming down or steel wire brushging, scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of white wash complete all as specified and directed.

M&L for preparing new plastered or un-plastered ceiling surfaces and applying three coats of white wash complete all as specified and directed.

M&L for two coats of oil bound distemper over one coat of 1mm thick wall care putty ( Make : Birla/JK White) base on newly plastered surfaces of wall including preparation of surfaces complete all as specified and directed.

M&L for complete removal of existing treatment (any no of layer) of wall and applying two coats of oil bound distemper over one coat of 1mm thick wall care putty (Make : Birla/JK White) base on old treated surface including preparation of surfaces complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of white cement as primer complete all as specified and directed.

M&L for preparation of old decorated plastered or unplastered wall surfaces including brooming down or steel wire brushging, scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of cement base paint complete all as specified and directed.

M&L for preparation of old painted wooden surface of any description, over 10cm width or girth and applying one coats of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new wooden surface of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

M&L for preparation of new steel surface of any description exc. 10cm width or girth and applying two coats of synthetic enamel paint over a coat of primer complete all as specified and directed.

M&L for writing letters or figures (block, roman, Italic or Indian) not exc. 30cm high with synthetic enamel paint complete all as specified and directed.

Taking up or down steel tubing and connections for 15mm bore of pipe complete all as specified and directed.

Taking up or down steel tubing and connections for 20mm bore of pipe complete all as specified and directed.

Supply and laying of 20 mm outer dia CPVC pipe SDR 11 fitting on walls /ceiling or laying in floors including connection to old GI pipe if required complete all as specified and directed.

S&F of 20 mm outer dia CPVC elbow (3/4x 1/2) with brass thread at one end for fixing of taps etc and other end plain complete all as specified

S&F of 20mm outer dia CPVC Tee with brass thread at one end for fixing of taps etc and other end plain complete all as specified

S&F of 20 mm outer dia CPVC adopter with female brass thread at one end for fixing of taps etc and other end plain complete all as specified

S&F, steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 15mm bore of pipe complete all as specified and directed.

S&F, steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 20mm bore of pipe complete all as specified and directed.

Refixing old serviceable steel tubing and connections in new or old position (walls, ceilings, floors etc.) for 20mm bore of pipe complete all as specified and directed.

S&F in repair Gun metal globe or gate valve, with iron wheel head, screwed both ends for iron pipe for 20 mm bore of pipe complete all as specified and directed.

Dismantling of cast iron, PVC or reinforced concrete drain pipes jointed in cement mortar for 110mm and 75mm bore of pipe from wall/floors etc complete all as specified and directed.

S&F, 75mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints fixed to walls including MS Z stack clamp complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints laid in trenches or floor complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints fixed to walls including stack clamp complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints laid in trenches or floor complete all as specified and directed.

S&F, 75mm bore PVC (SWR) bend, any radius with access door complete all as specified and directed.

S&F, 75mm bore PVC (SWR) bend, any radius complete all as specified and directed.

S&F, 110mm bore PVC (SWR) bend, any radius with access door complete all as specified and directed.

S&F, 110mm bore PVC (SWR) bend, any radius complete all as specified and directed.

S&F 110mm bore PVC (SWR) Tee equal or unequal any radius with access door complete all as specified and directed.

S&F, 110mm bore PVC vent cowl complete all as specified and directed.

Disconnecting, setting aside (or lowering if required) and Cleaning & removing all scale and dirt etc from HDPE water tanks of 500 litres capacity (Tanks placed on top of roof) and from mouths of circulating pipes etc including washing the tank with bleaching powder and hoisting, reconnecting and re-fixing in position including complete, all as specified and directed.

Supply, hoisting, fixing in position and connecting, in repairs, 500 litres capacity rotational moulded polyethylene water storage tank double layered (cylindrical, vertical with closed top), ISI marked,including dismantling of old PVC/AC tanks of 500 litre capacity and fixing arrangement for inlet/outlet/over flow and vent pipe of standard size all as specified in SSR Part-I complete all as specified and directed. Note- The water tank etc shall be contractor's supply.

S&F, 20mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed complete all as specified and directed.(Minimum weight -210 Gms)

S&F, in repair, 20mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed complete all as specified and directed.(Minimum weight -210 Gms)

S&F in repair vitreous China squatting pan 'Orissa pattern' size 580x440 mm, white with integral foot rest including 'P' or 'S' trap front or back inlet excluding flushing cistern and flush pipe including connection to trap and flushing pipe etc and making good to floor complete all as specified and directed.

S&F, in repair kitchen sink with drainage board made of stainless steel 1mm thick including supply and fix 32mm CP waste coupling, plug, washer, 32 mm bore and 60cm long PVC waste pipe including cantilever brackets made of mild steel angle iron 30x30x4mm and flat iron 25x3mm both duly painted with two coats of synthetic enamel paint over a coat of red oxide primer, cutting for and pinning in ends of brackets to errecting stand into wall and making good disturbed portion in cement mortar 1:2 or in PCC 1:2:4, type B-1 using 20mm graded stone aggregate and connecting union to pipe, over all size 915mm x 460mm and bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F, in repair, 0.63 mm thick, heavy duty stainless steel plate rack of size 24x30x10 inch complete all as specified and directed.

S&F, in repair, 10 litres capacity, PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet ball valve, float and handle including brackets and connection to pipe or lever etc. complete all as specified and directed.

S & F in repairs chromium plated with long shank and cup (concealed type) 15 mm bore Stop valves, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as directed.

S & F in repairs chromium plated Stop Valves (Angle type) fancy type 15 mm bore Stop valves, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as directed.

S & F in repair Bib taps long body cast copper alloy chromium plated with crutch or butterfly handle, fancy type, screwed down, screwed for iron pipe or for brass ferrule 15 mm bore complete.

Supply only PVC connection 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed.

S&F, in repair, brass chromium plated shower rose with or without swivel joint, 125mm size complete all as specified and directed.

S&F in repair bathroom corner self super clean (transparent) unbreakable heavy duty set of 3 pieces (7",9" & 11") (As per sample)

S&F, in repair, plastic unbreakable heavy duty wall mounted square shelf tray of 450mm with decorative railing complete all as specified and directed.

M&L for machine cut kota stone slab, 18-20mm thick as in flooring laid over and including cement mortar screed bed of 15mm thick in CM (1:6), laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for machine cut kota stone slab 18-20 mm thick as in riser of steps, skirting, dado and pillar laid over and including rendering 10mm thick in cement mortar (1:4), jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

S&F,in repair brass chromium plated, tubular towel rail 20mm dia, D type, 600mm long complete all as specified and directed.

S & F in repair Soap dish, stainless steel, standard size Soap dish, any type, fixed to plugs with chromium plated brass screws complete.

S&F in repair 25mm dia, 1mm wall thickness stainless steel fancy type heavy duty curtain rod with decorative ball type side brackets (as per sample) fix with wooden gutties complete all as specified and directed.

S&F, in repair, PVC (SWR) floor trap, with chromium plated grating including jointing with solvent cement, dia of outlet 75mm complete all as specified and directed.

S&F, in repair, 40mm bore, low density polyethelene pipe (LDPE) of pressure rating 6kgf/sq.cm fixed to walls, ceilings or in floors etc. complete all as specified and directed.

Taking down carefully copper/aluminum point wiring (light, fan,socket or power) complete,including fixture and fitting such as as switches, ceiling roses, pendants, regulators, sockets,etc excluing light fittings etc,removing materials to store for keeping in safe custudy or for taking credit ( credit for above items should be made as per conditions separately) and making good disturbed surface of walls, ceiling, floor etc to match with the existing surface complete all as specified and directed.

M&L for wiring with and including multi stranded copper conductor 1.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed, FRLS cable, 1100 volts grade, ISI marked with valid CML number, drawing through in and including, rigid non metallic, PVC concealed conduit of 20mm bore and including cutting chases for conduits and sinkings for boxes, its accessories & including with multi stranded copper conductor 1.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed, FRLS cable, 1100 volts grade, ISI marked with valid CML number as continuity earth wire terminating with provision sunken concealed terminal boxes complete all as specified and directed for the following :-

(a) One light/fan /Exhaust point controlled by one switch

(b) One multi purpose socket 5 Amps, Independent board.

(c) One multi purpose socket 5 Amps, on the same board.

M&L for wiring with and including multistranded copper conductor 2.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number drawn in and including medium grade PVC concealed conduit of 20mm bore fire resistant, ISI marked including with its fittings and fixtures such as tees, bends, elbows, junction boxes, etc. including multistranded copper conductor 2.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number as continuity earth wire and including pressed steel sunken concealed terminal box complete all as specified and directed.

S&F, lamp holder insulated body with back plate for battern fittings complete all as specified and directed.

S&F, in repair, switch piano, flush button single pole, one way 5 Amps complete all as specified and directed.

S&F, in repair, switch piano, flush button single pole, one way 15 Amps complete all as specified and directed.

S&F, in repair, socket outlet multipurpose, 3 pin, 5 & 15 Amps flush type complete all as specified and directed.

S&F, in repair, socket outlet 2 in 1, 3 pin, 5 Amps, flush type complete all as specified and directed.

S&F, Ceiling rose, PVC/poly carbonate,isolated body three terminals,complete all as specified and directed.

S&F, in repair Distribution Board SPN 4 way, 240 volts, factory made powder coated, double door with neutral and earth link, suitable for fixing MCB,s complete including connecting all as specified and directed.

S & F in repair MCB’s single pole, 6 to 32 Amps 240 volts with ‘C’ curve, fixed in sheet metal board complete including connecting.

S & F in repair MCB’s SPN 40 Amps 240 volts with ‘C’ curve, fixed in sheet metal board complete including connecting.

Fixing only, LED light fitting, 1 x 20 watt 220V, AC, decorative box type with driver , holder , including LED tube light complete set flexible three core copper conductor cable of suitable size and testing on completion all as specified and directed.

Taking down existing fan and depositing in MES store yard for keeping in safe custody and refixing the same after completion of works, complete all as specified and directed.

Taking down existing electric meter and keeping in safe custody and refixing the same after completion of work, complete all as specified and directed.

JIYA CONSTRUCTION