MP-LBC Providing screw gear shutters to LB Main canal Ch18/000 to 19/500 km and Kadalakurissi, Edathara branches from 0/000 to TD - Phase 2

Amount

DISMANTLING and STACKING the existing damaged shutter, hoisting girder, base & nut and Screw rod and stacking at convenient place. Providing BUND for carrying out concrete works.

od36535/2020_2021/MH : Taking out the mud debris and cleaning the bay, removing the plastic and bio waste and disposing at a suitable place 50m away from site

od36540/2020_2021/MH : Dismantling of shutters ( where there is road acess to the point) from the grooves and stacking including cost of all machinery, labour all incidental and conveyance charges etc. complete as per directions of departmental officers at site (weight of unservicable shutters and embedded parts may be calculated as 60% and unserviceable hoisting units as 80%)_..

od36536/2020_2021/MH : Providing BUND - putting up bund , 1m bottom width and 0.5 m height using empty gunny bar polythene bag filled with earth for an total length of 1 m includinglabour.Vol. of bund 1*0.5*1=0.5m3No. of bags 0.5/0.027 =19nos

od36537/2020_2021/MH : Removing BUND - 1m bottom width and 0.5 m height using empty gunny bar polythene bag filled with earth for an total length of 1 m.Vol. of bund 1*0.5*1=0.5m3No. of bags 0.5/0.027 =19nos

DEMOLISHING the existing Concrete for C GROOVE and SILL BEAM

15.2.1 : Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

FORM WORK, PCC and PLASTERING for C groove and Sill level

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.1.2 : Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

Supply, fabrication, erection of MS and SS EMBEDDED PARTS

85.101 : Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges

85.102 : Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges

od36288/2020_2021/MH : Fabrication, Supply, erection and assembling in correct position and alignment by welding SS EMBEDDED PARTS in 304L Grade like roller track, seal track,Seal seat etc as per approved specifications, drawings and directions of deptl officer at site including cost of all materials,labour,machinery for planing, welding,shearing, grinding etc,lead and lift, conveyance, incidental and handling etc complete

od36291/2020_2021/MH : Fabrication and supply of Embedded parts of CANAL GATE ( Less than 2 tonne weight ) and accessories as per approved specifications, drawings and directions of deptl officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc complete but excluding cost of material already supplied

od36289/2020_2021/MH : ERECTION of the EMBEDDED PARTS of CANAL SHUTTER ( Less than 2 Tonne weight ) including . in correct alignment ; setting and aligning complete including cost of all labour, machinery, incidental and conveyance , lead and lift charges etc complete but excluding cost of materials already supplied

Supply of MS SHUTTER

85.101 : Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges

85.102 : Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges

Providing SCREW ROD and BASE & NUT

od36295/2020_2021/MH : Providing base and nut arrangement for hoisting the shutter including cost of all materials labour etc. complete_..

od36296/2020_2021/MH : Providing EN-8 square threaded screw rod 7.5 tonne capacity 4.00 M lift screw hoist having 1No of EN-8 screw shaft having a lifting speed of around 5cm/min for 24RPM of hand operation including cost of all materials, labour, hire charges and conveyance.._

od36297/2020_2021/MH : THREAD LESS portion of the screw rod (per metre rate)

od36298/2020_2021/MH : SUPPLYING and APPLYING GREASE on NEW SCREW ROD for CANAL GATE

od25325/2018_2019/MH : supply of bolt and nut upto 300 mm length including cost of conveyance

Supply of HOISTING BRIDGE unit

85.101 : Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges

85.102 : Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges

85.107 : Supply of MS round bar including cost of conveyance charges

Fabrication, painting and erection of MS SHUTTER and HOISTING BRIDGE

od36299/2020_2021/MH : FABRICATION and supply of structural steel canal shutters ( Up to 2 tonne weight) / HOISTING BRIDGE / Platform and accessories etc. for the same as per approved specifications, drawings and directions of deptl officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc complete but excluding cost of material already supplied.._

85.114 : Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site

od36300/2020_2021/MH : ERECTION of the CANAL SHUTTER ( Up to 2 tonne weight )/ HOISTING BRIDGE /PLATFORM including handrails , ladder etc. for the same includng alignment correcting and setting complete including cost of all labour, machinery, incidental and conveyance , lead and lift charges etc complete but excluding cost of materials already supplied.._

ROLF ENGINEERING CO.

Bidder Name

ROLF ENGINEERING CO.

P.Damodaran, G.R.Industries