Providing LWSS group of panchyat phase II in GP Jaral in Tehsil Nihiri Distt Mandi

Amount

Excavation in foundation trenches etc. in earth all kinds of soil such as pick work jumper work blasting soft or hard rock or by chiselling soft or hard rock where blasting is prohibited in all leads and lifts including trimming/ chiselling of sides and bed stacking the excavated soil clear from the edge of excavation and returning the excavated soil after completion of work in 15cm layers when required into plinth sides of foundation etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil complete in all respect as per the direction and to the entire satisfaction of the Engineer-in-charge.

Providing and laying cement concrete 1:6:12(1cement: 6 sand: 12 graded stone aggregate 40mm nominal size) and curing complete excluding the cost of form work in foundatioin and plinth in all leads and lifts

Providing and laying cement concrete 1:2:4(1cement:2 sand: 4graded stone aggregate 20mm nominal size) and curing complete excluding the cost of form work in foundation and plinth in all leads and lifts.

Randum rubble masonary polygonal rubble masonary (uncoursed brought to courses in walls with hard stone of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (1cement: 6 sand: 12 graded stone aggregate 20mm nominal size) in cement mortar 1:6 (1cement: 6 sand) in breast wall and retaining wall including all leads and lifts.

Brick work using common burnt clay building bricks masonary in in foundtion and plinth in cement mortor 1:6(1cement :6sand) 2nd class bricks

Half bricks masonary in common burnt clay building bricks in foundation and plinth incement motor 1:4( 1cement : 4sand) in all leads and lifts.

Providing wood work in frames of doors, windows, clerestory windows and other frames wrought , framed and fixed in position in all leads and lifts.(a) 2nd class deodar wood.

Providing and fixing panelled glazed or panelled and glased shutters for doors, windows and clerestory window including black enamelled iron but hinges with necessary screws(40mm thick) 2nd class dedoar wood in all leads and lifts..

Providing form work with steel plates 3.15mm thick welded with angles iron in frame 30x30x5mm so as to give a fair finish including centring shuttering strutting and propping etc. with wooden battens and ballies height of propping and centring below supporting floor to ceiling not exceeding 4 mtrs and removal of the same for in-situ reinforced concrete & plain concrete work in:-(a) Foundation footing bases of columns etc and mass concrete as directed in all leads and lifts and to the entire stisfaction of the Engineer -in -Charge.

(b) flat surfaces such as soffits of suspended floors,roofs, landings and the like in(a) floor etc. upto 200mm thickness.

(c) Beam, cantilivers, girders and lintels side and soffits of beam haunches cantilivers girder bressumers and lintle not exceeding 1 mtr in depth in all leads and lift.

Providing and laying cement concrete 1:2:4(1Cement :2 sand:4 graded crushed stone aggregate 20mm nominal size and curing completre excluding the cost of form work and reinforcement for reinforced concrete in beas cantilevers etc. (a)Suspended floors, roofs, landing, shelves and their supports balconies, lintels, beams girders bresmers and cantilevers upto all floor two level .

Providing Tor steel reinforcement for RCC work including bending, binding including cost of binding wire and placing in position complete upto floor two level in all leads and lifts.

6mm cement plaster to ceiling in cement mortar 1:3 (1 cement : 3 sand) in all leads and lifts.

15mm cement plaster in single coat on rough side of brick/ concrete/ stone walls for interior plastering upto floor two levels including arrises internal rounded angles chamfers and / or rounded angles not exceeding 80mm in girth and finished even and smooth in cement mortar 1:6 (1cement:6sand) in all leads and lifts.

Providing and fixing MS grills of required pattern in wooden frames of windows etc. with MS flats, square or round bar with roundheaded bolts and nuts or by screws (Plain grills)

Providing and fixing wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designatioin 85G with wire of dia 0.56mm for doors, windows and clerestory including bright finished black enamelled iron hinges with necessary screws 40mm thick 2nd class deodar wood.

Boulder filling under floor in all leads and lifts.

Providing and laying cement concrete 1:4:8(1cement:4 sand: 8graded stone aggregate 20mm nominal size) and curing complete excluding the cost of form work in foundation and plinth in all leads and lifts.

Cement concrete flooring 1:2:4 (1cement:2sand: 4 graded crushed stone aggregate 20mm nominal size) laid in one layer finished with a floating coat of neat cement in all leads and lifts. (a) 40mm thick

Providing plinth protection 50mm thick in cement concrete 1:3:6 (1cement:3 sand: 6 graded crushed stone aggregate 20mm nominal size) in all leads and lifts.

White washing with lime on undecorated wall surfaces two coats give an even shade including thoroughly brooming the surface to remove all dirt dust and other forign matter in walls in all leads and lifts.

Distempering with dry distemper of approved brand and manufacture (two coats) on previous distemper of required shade on decorated wall surfaces to give an even shade after thoroughly brushing the surface clean of grease dust, loose, pices of sealed including preparing the surface even and sane papered smooth and one subsequent coat in all leads and lifts.

Finishing wall with water proofing cement paint of approved brand and manufacture and of required shade on un-decorated walls surfaces (two coats to give an even shade after throughly finishsing the surface to remove all dirt and remains of loose powdered materials.

Providing and fixing anodized MS sliding door bolts with nuts and nuts screw etc. complete in all leads and lifts.(i) 300x16mm

Providing and fixing oxidized MS tower bolts (barrel type) with screws etc. complete in all leads and lifts. (i) 250x10mm

Providing and fixing MS handles with necessary screws etc. complete in all leads and lifts.(i)100mm

Applying priming coat on new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease , dirt and other foreign matters, sand papering and knotting ready mixed paint brushing wood primer pink in all leads and lifts.

Painting two coats (excluding priming coat) on new wood and wood based surfaces with enamel paint to give an even shade including cleaning the surface of dirt, dust and other foreign matters sand papering and stopping with readymade paint other than white in all leads and lifts.

Naresh Kumar

Tulsi Ram

Ramesh Kumar