Tender for RMU Installation, Testing and commissioning of 11/22KV, SCADA Compatible, RRLL/RRL type-3/4 Way, RMU including Construction of plinth for RMU as per approved drawing by DGVCL at VARIOUS sub division under RANDER Division.

Name of Work:Tender for Installation, Testing and commissioning of 11/22KV, SCADA Compatible, RRLL/RRL type-3/4 Way, RMUincluding Construction

of plinth for RMU as per approved drawing by DGVCL at VARIOUS sub division under RANDER Division.

SR.NO DESCRIPTION UNIT RATE IN RS QTY

1 9925000001 Labour charge for excavation of cable Meter

trench of 400mm width x 1200mm depth, in any type of soil for laying of cable

of size up to 240 mm2 (For additional cable 200 mm additional width shall be

considered i.e. half trench length is to be considered

2 9925000002 Labour charge for excavation of cable Meter

trench of 600mm width x 1200mm depth, in any type of soil for laying of cable

of size up to 240 mm2 (For additional cable 200 mm additional width shall be

considered i.e. half trench length is to be considered

3 9925000003 Labour charge for excavation of cable Meter

trench of 400mm width x 1500mm depth, in any type of soil for laying of cable

of size up to 240 mm2 (For additional cable 200 mm additional width shall be

considered i.e. half trench leng th is to be considered

4 9925000004 Labour charge for laying of 11kV / 22 kV Meter

XLPE Cable of size up to 240 mm2 & preparation of sand layer 100mm thick, in the

cable trench & covering the cable with 150 mm dia (Inner), thickness 25 mm,

meter long RCC half round muffs and providing and fixing of 4inch width yellow

colour polyethylene tape with printing"CAUTION ELECTRIC CABLE BELOW' at

0.75 m depth from ground surface after laying cable in trench. This will provide

indication that electric cable is passing underground so as to protect cable from

mechanical injuries, refilling the same, as per Instruction of E gineer in Charge

5 9925000005 Labour charge for horizontal drilling Meter

using Auger machine without damage to surface road at max 2.0 mtrs depth & putting

of 6.11 kg/cm2 , class-4,Green color, 110mm 0.D. 8.5mm thickness

H.D.P.E. pipe confirms to IS 4984- 1987(3rd revision) and BIS certification and

laying of 11KV/22KV XLPE cable of size up to 240 mm2 in HDPE pipe, as per Site

Condition (excluding cost of pipe). The detail map obtained from HDD machine

and excel sheet hard and soft copy) indicating the respective depth and distance

from adjacent landmark for each segment for HDD is must require to be submitted.

HDD to be carried out at depth 1.5 mtrs to 2.0 mtrs as per site conditions and as

er instruction of EIC.

6 9925000006 Labour charge for horizontal drilling Meter

manually without damage to surface road at max 2.0 mtrs depth & putting of

6.11 kg/cm2 , class-4,Green color, 110mm O.D. , 8.5mm thickness

H.D.P.E. pipe confirms to IS 4984- 1987(3rd revision) and BIS certification and

laying of 11KV/22KV XLPE cable of size up to 240 mm2 size, as per Site Condition

(excluding cost of pipe). The detail map and excel sheet (hard and soft copy)

indicating the respective depth and distance from adjacent landmark for each

segment of cable to be submitted. Drilling to be carried out at depth Minimum 1.2 mtrs

to 2.0 mtrs as per site conditions as per instruction of EIC.

7 9925000007 Supply of 6.11kg/cm2 , class-4,Green Meter

color, 110mm O.D. , 8.5 mm thickness

H.D.P.E. pipe confirms to IS 4984 and BIS certification for laying of

underground 11KV/ 22KV XLPE cable up to 240 mm 2 size.

8 9925000008 Labour work for RCC concreting on CMT

disputed location and repairing of damage portion of road crossing for the work

carried out for roads crossing as well as concreting & muffing of poles including all

9 9925000009 Providing & fixing concrete stone route No

marker of 300 mm width x 150 mm thick x 650 mm height embedded in earth at least

300 mm below & 350 mm above ground level respectively at distance approx.

meters along the length of cable. The RCC concreting (1:2:4) (all necessary

materials will be in bidder's scope) of route marker is to be carried out 300 mm

width x 150 mm thick x 300 mm below ground level as per instruction of EIC. The

route marker should be with name of company with approved yellow colour-DGVCL.

The distance from marker to cable and cable depth with feeder name etc., marked with

arrow sign is to be painted on it. The route marker is to be fixed at location

near to any fixed permanent location (not necessary to fix exact on top of cable) as

per instruction of EIC.

10 9925000010 Erection of D.P. (double pole) structure No

using 9 / 11 Mtr. RSJ pole with cable connection arrangement along with fitting

of necessary fabrication for 11KV cable including excavation of pit & refilling of

earth as per instruction of EIC. (Exclusive of concreting & muffing of poles)

11 9925000011 Erection of Single pole structure using 9 No

/ 11 Mtr RSJ pole with cable connection arrangement along with fitting of

necessary fabrication for 11KV/22 KV cable including excavation of pit & refilling of

earth as per instruction of EIC. (Exclusive of concreting & muffing of poles

12 9925000012 Erection of D.P. (double pole) structure No

using 8.0 Mtr. PSC pole with cable connection arrangement along with fitting

of necessary fabrication for 11KV cable including excavation of pit & refilling of

earth as per instruction of EIC. (Exclusive of concreting & muffing of poles

13 9925000013 Erection of Single pole structure using No.

8.0 Mtr PSC pole with cable connection arrangement along with fitting of

necessary fabrication for 11KV/22 KV cable including excavation of pit & refilling of

earth as per instruction of EIC. (Exclusive of concreting& muffing of poles

14 9925000014 Labour charge for erecting of 11kV / 22 per job

kV XLPE cable of size up to 240 mm 2 on DP Structure with fixing of 02 Nos polymer

cleats on top and middle part. Polymer cleats, nut bolts etc. fixing material to be

provided by contractor.

15 9925000015 Providing & fixing of 6.11kg/cm2 , perJob

class4,Green color, 110mm O.D. 8.5mm thickness H.D.P.E. pipe confirms to IS 4984 and

BIS certification on the erected DP structure for the mechanical protection of

cable by inserting the cable inside HDPE pipe. The HDPE pipe shall be erected in such a

way that 300mm shall be below the ground level and the rest 2700 mm shall be

supported on the DP Structure with 01 No Polymer cleat. All materials including polymer

cleat and Nut bolt to be provided by contractor.

16 9925000016 Providing and fixing of pipe type earthing No

from 80 mm dia class-B GI pipe with pit to be filled with salt & coke and

construction of chamber as per DGVCL Drg. No. dg /100 for DP and cable. The earthing

pit should be joined with cable by G.I. strip of size 1" width & 2 mm thick. All

material GI pipe, Coke Salt etc will be supplied by bidder.

17 9925000017 Supply & fixing of heat shrink type end No

terminations (outdoor) for up to 11kV 3C x 185 mm2 size XLPE cable as per DGVCL

technical specification

18 9925000018 Supply & fixing of heat & shrinkable end No

terminations (outdoor) for up to 22 kV 3C x 185 mm 2 size XLPE cable ( as per DGVCL

technical specification)

19 9925000019 Supply & fixing of heat shrinkable type No

end terminations (indoor) for up to 11kV 3C x 185 mm 2 size XLPE cable as per DGVCL

technical specification

20 9925000020 Supply & fixing of heat & shrinkable end No

terminations (indoor) for up to 22 kV 3C x 185 mm 2 size XLPE cable as per DGVCL

technical specification

21 9925000021 Supply & fixing of heat shrinkable No

straight through joint for up to 11kV 3C x

185 mm 2 size XLPE cables as per DGVCL technical specification.

22 9925000022 Supply & fixing of heat shrinkable No

straight through joint type for up to 22kV 3C x 185 mm 2 size XLPE cable as per DGVCL

technical specification

23 9925000023 Labour charge for excavation of No

2100mm long x 1200mm wide x 1200 mm deep joint pits for installation of 11kV

/ 22kV Straight through joints as per instruction of engineer-in-charge & covering

the cable with 150 mm dia (Outer), thickness 25 mm, 1.0 meter long RCC half

round muffs & refilling same as per instruction of EIC .

24 9925000024 Providing and fixing of insulating bus No

bar, made from 11KV/22KV XLPE cable after removal of semi conducting layer and

applying of PVC heat shrinkable antitracking core insulating tubing (1.1KV), on

both end terminal using Aluminium long barrel heavy duty up to

240 sq mm lugs, Aluminium bus connector. Taping with PGclamp for bus

conductor as per drawing and as per instruction of EIC. The Allurninium lugs and PG

clamp shall be covered with 11KV/22KV HT insulating tapes. (11KV/22KV XLPE

cable will be in scope of DGVCL while all other materials will

be in bidder's scope.

25 9925000025 Testing of cable at various points and commissioning the feeder as per No

instruction of engineer-in-charge.Test result shall be submitted by contractor with

26 9925000026 Preparation and submission of 6 (six) copies, of complete layout drawings with GIS Set

mapping as per actual cable routing showing road crossing, HDPE pipe sleeving,

jointing locations, markers etc.

27 9925000027 Providing and fixing of Sign Board at junction point Made out of 2 mm No

aluminium sheet size 750x300 mm (2.5 x 1 ft) rectangle, as per design,

pretreated with phosphate process and acid etching coated with one coat of epoxy

primer and two coats of best quality paints, reflectorized with Hi Intensity

retro — reflective sheeting as per the latest and frame fabricated from suitable size iron

angle. The Sign Board is to be fixed on the base prepared from channel and bracing

angles which is grouted by means of cement concreting of 1:2:4 for size of 300 mm

dia x 800 mm height (500 mm to be grouted in ground). The details to be displayed

on sign board will be given by InchargeEngineer. (a) Hi intensity Micro

prismatic Grade

28 9925000028 Providing and fixing of Sign Board (Danger Board) on Distribution No

Transformer Centers Made out of 2mm aluminium sheet size 300x300mm (1X1 ft)

as per design, pre treated with phosphate process and acid etching coated with

one coat of epoxy primer and two coats of best quality paints, reflectorized

with Hi-Intensity retroreflective sheeting as per the latest and frame fabricated

from suitable size iron angle. The Sign Board (Danger Board is to be fixed at the

location as per instruction of In-charge Engineer.

(a) Hi intensity Micro prismatic Grade

29 9925000029 Providing & fixing of aluminium tag of size 250 mm (L) x 75 mm (W) from 3 mm No

aluminium sheet along with 1.0 mm dia aluminium binding wire for fixing of aluminium

tag near end termination joint at DP structure for identifying the cable. The details of

feeder i.e. 11 / 22 KV with feeder name should be punched on the tag by letter punch of

size 16 mm as per instruction of In-charge Engineer.

30 9925000030 Supply & fixing of heat shrink type end terminations (outdoor) for 11kV 3C x 240 Nos

mm2 size XLPE cable as per DGVCL technical specification.

31 9925000031 Supply & fixing of heat & shrinkable end terminations (outdoor) for 22 kV 3C x 240 Nos

mm2 size XLPE cable as per DGVCL technical specification

32 9925000032 Supply & fixing of heat shrink type end terminations (indoor) for 11kV 3C x 240 mm2 Nos

size XLPE cable as per DGVCL technical specification

33 9925000033 Supply & fixing of heat & shrinkable end terminations (indoor) for 22 kV 3C x 240 mm2 Nos

size XLPE cable as per DGVCL technical specification

34 9925000034 Supply & fixing of heat shrinkable straight through joint for 11kV 3C x 240 mm2 Nos

size XLPE cables as per DGVCL technical s ecification.

35 9925000035 Supply & fixing of heat shrinkable straight through joint type for 22kV 3C x 240 Nos

mm2 size XLPE cable as per DGVCL technical s ecification

36 9925000038 Installation, Testing and commissioning of 11 KV,630 A SCADA Compatible, RRL Nos

type3 Way RMU including Two numbers of earthings as per Drawing (material is in

bidder's scope) and as per DGVCL Technical specification.

37 9925000039 Installation, Testing and commissioning of 11 KV,630 A SCADA Compatible, RRLL Nos

type4 Way RMU including Two numbers of earthings as per Drawing (material is in

bidder's scope) and as per DGVCL Technical specification.

38 9925000040 Installation, Testing and commissioning of 22KV,630 A SCADA Compatible, RRL type-3 Nos

Way, RMU including Two numbers of earthings as per Drawing (material is in

bidder's scope) and as per DGVCL Technical specification.

39 9925000041 Installation, Testing and commissioning of 22KV,630 A SCADA Compatible, RRLL Nos

type-4 Way, RMU including Two numbers of earthings as per Drawing (material is in

bidder's scope) and as per DGVCL Technical specification.

40 9925000042 Construction of plinth for 11KV, RRL type- 3 Way( i.e Two numbers of Isolator & One Nos

number of Breaker) Ring Main Unit as per DGVCL's technical specification

mentioned in drawing no: Drg. 11kv-01. All required material will be supplied by

41 9925000043 Construction of plinth for 11KV, RRLL type4 Way (i.e Two numbers of Isolator & Two Nos

number of Breaker)Ring Main Unit as per DGVCL's technical specification

mentioned in drawing no:Drg. 11kv-02.AlI required material will be supplied by

42 9925000044 Construction of plinth for 22KV, RRL Nos

type- 3 Way (i.e Two numbers of Isolator & One number of Breaker) Ring Main Unit

as per DGVCL's technical specification mentioned in drawing no: Drg. 22kv-01.

All required material will be supplied by contractor.

43 9925000045 Construction of plinth for 22KV, RRLL type4 Way (i.e Two numbers of Isolator & Two Nos

number of Breaker)Ring Main Unit as per DGVCL's technical specification

mentioned in drawing no:Drg. 22kv-02.All required material will be supplied by

44 9925000046 Modifications e.g. Providing and fixing of Terminal protectors i.e. Re-use able boot (HT no

Side 11/22KV, LT Side 1.1KV) including 11/22 KV insulating taps and L.T.(I.I KV)

insulating taps ,Busbar, Tapping from Bus Bar (11/22 KV XLPE cable) through P.G.

Clamp for H.T. Jumper to D.O. Fuse to bushings of Transformer Center, providing

& Fixing of jumper and providing & fixing of Heat Shrinkable Anti Tracking CoreInsulating

Tubing (Insulation Level 11/22 KV) in H.T. jumper , Clamping arrangement of cable

support frame on both side of existing Over Head type Distribution Transformer

to utilize in Under Ground cable network as per drawing & as per instruction of

Engineer incharge. All live parts i.e. PGClamp, connections of D.O.fuses, HT

bushings etc . shall be covered with fixing of 11/22 KV HT insulating tapes. ( 11/22

KV XLPE cable will be in scope of DGVCL while all other materials will be in bidder's scope )

45 9925000047 Laying of any size of 11/ 22 KV XLPE/PILCCable in readymade trench or in open per cable

46 9925000060 Labour charges for Lying of O/H XLPE cable pole to pole (Including all KM

47 Dismental OF 100MM2 AAAC CONDUCTOR KM

48 9926000064 Binding of messanger Conductorat with a distance not more than 0.75 mtr with 6 turns NO

minimum on XLPE Cable with single strand binding wire (including cost of binding

49 Supply and fixing of Suspenssion clamp to Hold the cable (J-Hook) no

Rates are exclusive of all taxes.

TDS, GST will be applicable as per Govt. rules and regulations.

Exe. Engineer (O&M)

% Above /Below of Estimate Amount DGVCL, Rander Division

Stamp/Sign of Contractor