SPL REPAIR OF 08 X OR MD ACCN OF NO. 2 TRG BN AT BEG AND CENTRE UNDER GE ROORKEE

Amount

Demolition of cement concrete (reinforced) of any position not otherwise specifically provided for and including reinforcement required to facilitate demolition upto and including fourth story and on the roof top/mumty/parapet and removal of debris and rubbish off premises outside MoD land complete all as specified and directed.

M&L for mild steel TMT bars of 10 mm dia and over cut to length bent to shape required including cranking, bending etc and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L for providing pre-cast reinforced cement concrete (1:2:4) type B-1 using 20 mm graded crushed stone aggregate and set in CM (1:4) as in shelfs and directed.

M&L for providing reinforced cement concrete (1:2:4) type B-1 using 20 mm graded crushed stone aggregate as in Chajjas complete all as specified and as directed.

M&L for reinforced cement concrete (1:1½ :3) type A-1 (using 20 mm graded stone aggregate) as in beams, cantilevers, lintels over 1.5 m span, bressumers and the like complete all as specified and directed.

Form work to sides and soffits of shelves etc including supports such as kitchen shelves, platforms and similar works rough finish surface of concrete (the thickness of slab/shelves n.exc. 100 mm) complete all as specified and directed.

Formwork to chullah hoods, chajjas, troughs and similar items including edges all as specified.

Demolition of cement concrete (un-reinforced) in Ground floors and paving n.exe 15cm thickness ( below or above ground level ) including removal of rubbish out side complex (MOD land), complete all as specified and directed.

M&L 75mm thick cement concrete 1:3:6 type C2 (using 40mm graded stone agg).as in Plinth protection laid to a slope of 1 in 24 in alternate bays system. Each bay shall not exceed 3m in length. 12mm wide & 75mm deep joint shall be formed between the bays which shall be filled with mastic filling to full depth comprising a mixture of 1 part of hot blow bitumen 85/25 portion and two parts of heated badrapur sand (by volume) etc complete all as specified and directed.

M&L for 75mm thick cement concrete (1:4:8)type D-2,using 40mm graded stone aggregate as in sub base of floor/handstanding/path complete all as specified and directed.

M&L Cement concrete 1:2:4 type B0(using 12.5mm graded crushed stone agg) as in roof leveling, finished even and fair, complete all as specified and directed

M&L for PCC (1:2:4) Ty B-0 using 12.5mm thick course aggregate as in cills, steps, parapets,, copings, and the like including weathering, slightly rounded or chamfered angles and throating, as directed

M&L Cement concrete type B1-1:2:4 (using 20 mm graded crushed stone agg) in roof kerbs or mud stop rounded or chamfered on edge etc complete all as specified and directed

M & L 100mm thick cement concrete type C-2, 1:3:6 (40mm graded aggregate), as in sub base complete all as specified & directed

M&L 75mm thick Cement concrete type D- 2, 1:4:8 (40mm graded aggregate) as in sub base/leveling course etc complete all as specified and as directed.

Demolition of brick work built in cement mortar in any description and position complete all as specified and directed.

M & L brick work with sub class "B" bricks straight or curved on plan exc 6 m mean radis built in CM 1:6 complete all as specified and directed

M&L for Brick work with "B" bricks straight or curved on plan to any radius in half brick thick wall built in CM 1:4 complete all as specified and directed.

Dismantling of Cast Iron pipe/PVC pipe up to 100 mm bore complete all as specified and directed.

Dismantling of Cast Iron pipe/ RCC drain pipe/PVC pipe exceeding 100mm and up to 150 mm bore complete all as specified and directed.

S&F PVC (SWR) pipes of 110 mm nominal outside diameter (Type B with wall thickness 3.20 to 3.80 mm) single socketed in any length with rubber ring joints including all fittings/fixtures fixed on wall or in trenches or in floor complete all as specified and directed.

All as per item No.21 above but 75mm nominal outside diameter.

S& F PVC (SWR) vent cowl suitable for 75 mm pipe

S&F 110 mm bore PVC (SWR) bends/shoes any radius complete all as specified and directed

All as per item No. 24 above but 75 mm bore.

S&F in repair PVC (SWR) 110 mm Nahani trap with stainless grating including jointing to waste pipe in cement concrete complete all as specified and directed.

S&F in repair PVC branch piece single (equal or unequal) 110 mm bore ordinary or inverted (spigot or socket type) or with parallel branches incl access door a complete all as specified and directed

S&F PVC (SWR) reducers 110mm dia, complete all as specified and directe

S&F in repair 110 mm pipe stack clamps make out of 50mmx 5 mm flat iron including bolts and nuts and securing ends of stays to walls or roof complete all as specified and directed.

All as per item No. 29 above but 75 mm bore pipe.

S&F PVC (SWR) junction, 110mm dia (Single T) or unequal provided with access door complete all as specified and directed.

S&F PVC (SWR) 75mm dia (Double T) or unequal provided with access door complete all as specified and directed.

Cutting into existing manholes for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 or 3/4 section ) in cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate finished smooth and reforming benching as required for 100/150mm dia pipes complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) laid bedded and pointed in any mortar and removal of old tiles from premises complete all as specified and directed.

M&L Non - skid coloured joint ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, set and jointed in neat cement slurry and pointed in white or coloured cement over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed

M&L Coloured Glazed ceramic tiles 300x600 x 7 to 8mm thick, as in vertical surfaces of wall such as dado/skirting, set and jointed in neat cement slurry and pointed in white or coloured cement over and including 10mm thick rendering in CM 1:4 complete all as specified.

S&F joint free non skid ceramic tiles coloured of 7 to 8 mm (squre/ rectungular ) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floors set and jointed in neat cement slurry and pointed with white or coloured cement over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

All as per item No 37 above but as in skirting over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M & L for 16-18 mm thick mirror polished Machine cut kota stone slab of size 22''x22'' for flooring over cement screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab laid over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L kota stone mirror polished slab with uniform texture of 16-18 mm thick in tread (Edge polished) of steps (to be flushed and provided with three Nos of grooves at the end on each step), riser of steps, skirting, dado and pillars in one single piece (size decided by Engineer-in-Charge) laid over and including cement screed backing coat of 10mm thick in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing , bevelled edge of corner etc complete all as specified and directed.

M&L for 18 to 20 mm thick Udaipur green Stone factory made bull nosed, pre polished (table rubbed and polished) as in jambs, window cills, cooking platform and the like etc in cement mortar 1:4 including pointing in white cement (1:2) using marble dust and admixture of pigment to match with shade of stone over and including 10 mm thick rendering in cement mortar 1:4 including rounding of edges, making hole for gas pipe and including suitable dia PVC sleacve complete all as specified and directed.

Dismantling of Brick tiles or terracing tiles, single layer on roofs, kerbs, aprons, etc. (each layer) and removal of rubbish out of defence land complete all as specified and directed.(Note : All roots of plant on either on wall or roof shall be removed and making good the disturbed surfaces. The rate quoted be the contractor shall be deemed to be included in the unit rates.)

Demolition of Mud Phuska in roofs,any thickness including plastering and leeping of any thickness upto 30cm deep complete all as specified and directed.(Note: All roots of plant on either on wall or roof to be removed and making good the distributed surfaces. The rate quoted by the contractor is deemed to be included in the unit rates including removal of mud phuska outside defence land.)

M&L for 40mm thick brick tiles laid on 15mm rhick cement mortar (1:6) and joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement on RCC surface complete complete all as specified and directed.

All as per item 44 above but except tiles.

M&L for cleaning of concrete or plastered roof surfaces and applying priming coat using bituminous primer @ 0.30 kg per sqm followed evenly a tack coat @ 1.2 Kg per sqm using 85/25 grade industrial hot blown bitumen over it laid 3 mm thick APP modified polymeric water proofing membrane minimum weight 3.6 Kg per sqm reinforced with non-woven polyester fabric (weight not less than 160 gm per sqm) rolled & bonded to substrate with side and end laps 75mm & 100mm as per manufacturer's instruction and applying over it a tack coat using industrial hot blown bitumen 85/25 grade @ 1.20 Kg per sqm and finally finished the top of polymeric water proofing membrane complete all as specified and directed. (Note:- Dismantling & Romoval of existing old water prrofing menbrane deemed to be included in quoted rate of this item)

Material & labour for cleaning of concrete or plastered surfaces of roof and applying priming coat using with bituminous primer @ 0.30kg per Sqm followed evenly by a tack coat @ 1.20 kg per Sqm using 85/25 grade industrial hot blown bitumen , over it laid with 3mm thick APP modified polymeric water proofing membrane minimum weight 3.6 Kg per Sqm reinforced with non-woven polyester fabric (weight not less than 160 Gm per Sqm) unrolled & bonded to substrate with side and end laps 75mm & 100mm as per manufacturer’s instruction and applying over it a tack coat using 85/25 grade industrial hot blown bitumen @ 1.20 kg per Sqm and finally finished the top of polymeric water proofing membrane with a coat of bituminous aluminum paint @ 0.20 kg per Sqm as per manufacturer’s instructions over, complete all as specified & directed Note: The rate quoted by contractor shall be deemand to (including removal of existing membrane and removal of scrape from site)

Taking down chowkhat or frames exc. 1.5 Sqm and n.exc 4 Sqm each with shutters (without taking off shutters from frames) complete all as specified and directed.

Taking down chowkhat or frames not exc. 1.5 Sqm each with shutters (without taking off shutters from frames) complete all as specified and directed.

Supply & fixing pressed steel frames for doors with one or more rebates including necessary fitting lugs, 6 No 125mm MS cold rolled, butt hinges, lock strike plates etc completed size of frame 165x60mm made out of 1.25mm MS sheets including PCC 1:2:4 Ty B0 using 12.5mm graded stone aggregate filling in frame complete all as specified & directed.

S&F factory made 35mm thick partly panelled and partly Glazed and skeleton shutters using second class hard wood, open rebated and prepared to receive glass, gauze, etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); for kitchen supplied and fitted to chowkats complete all as specified & directed.

S&F 35mm thick factory made Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides.

M&L for built in steel cup board with pressed steel frame of size 75 mmx45mmx1.25 mm th with pressed steel shutter 1mm th Godrej pattern fixed to masonry wall by hold fast made out of 25x3 mm flat iron including MS hanging rod of 10 mm dia with bracket fixed on inner side of one leaf of shutter and on other leaf provision of MS peg set of 3 pegs including locking arrangement brass lock 4 level spray paint over one coat or red oxide primer all around on steel surface of frame & shutter and making good disturbed portion in cm 1:3 or pcc 1:2:4 complete all as specified.

S&F factory made gauged shutter shall be made out of angle iron 35x35x5mm (outer frame) and 25x25x5mm (middle rail 2 nos, 150 mm apart from each other) and 1.0mm thick steel sheet covering on middle rail, 10mm Square bars @ 100mm C/C fixed vertical as grill complete with stainless steel fly proof wire mesh having 0.63mm nominal dia wire and 1.4mm average with aperture, with locking arrangement including two coats of synthetic enamel paint over a coat of red oxide prime as shown on drawing all specified and directed by Engr-in -charge.

S&F Fiber glass reinforced plastic (FRP) Flush door in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF) polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameter of FRP, laminate confirming to table 3 of IS -14856 Complete all as specified by the manufacturer and as per direction of Engineer -in- charge.

S&F FRP door frames three legged of cross section 90x45mm having single rebate 32mmx15mm. The laminated door frame moulded with fire retardant grade unsaturated polyester resin and chopped mat. Door frame laminated shall be 2mm thick, frame shall be covered with fiber glass from all sides ms flat iron 25x3mm shall be provided at the bottom to steady the frame including PCC 1:2:4 Ty B0 using 12.5mm graded stone aggregate as in frame, complete all as specified and directed.

S&F 100 mm long (size) butt hinges, mild steel,cold rolled complete all as specified and directed.

S&F 75 mm long (size) butt hinges, stainless AISI 304 grade with brass/bronze hinge pin , complete all as specified and directed.

S&F 300mm long, stainless steel of AISI 304 grade, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts complete all as specified and directed.

S&F Stainless steel of AISI-304 grade barrel tower bolt 200 mm long, extruded section complete all as specified and directed.

All as per item No.60 above but 75 mm long.

S&F extruded Stainless steel handles, fabricated type, anodised of size 150mm size long complete all as specified and directed.

S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor of 140mm long complete all as specified and directed.

M&L Preparation of new or previously untreated wood and wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L Preparation of new or previously untreated steel and steel based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of redoxide complete all as specified and directed.

M&L for powder coated aluminium window sliding type (3 shutter type) aluminium sections weighing 0.55 Kg/m(min) including stainless steel wire mesh , necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws suitable anodised fittings such as, hinges, handles, including anodised aluminium frame, including S&F 5 to 6 mm thick plain glass and all as specified & directed by Engr-in-charge. 'Note:- wire gauze/glass shall be measured and paid separately'

M&L for powder coated (50 micron thick) aluminium ventilator fixed type (partly glazed and partly gauzed) with gasket, glazing clip etc, weight of frame not less than 0.55 Kg/RM and weight of shutter frame not less than 0.425 Kg/RM including necessary joining cleats,rubber packing, anodised aluminium snap beading, screws suitable anodised fittings such as, hinges, including S&F 3 to 4 mm thick pin headed glass complete all as specified and directed. 'Note:- wire gauze/glass shall be measured and paid separately'

M&L for ply board 18 to 19 mm thick of density not less than 600 Kg/Cum fixed with screws & approved adhesive of good quality for cabinet car case and shelves as per sketch approved and all exposed surface covered with 0.80 mm thick decorative laminates, 'Mica" type 1 of surface finished,colour and pattern as approved by GE and the surface alongwith to wall shall be provided with 4mm thick PVC sheet in lieu of lamination sheet complete all as specified & directed. 'Note:- Ply board area shall be merasured for payment purpose.

S&F Auto hinges for cabinet case (Make ; KARF / HETICH) complete all as specified & directed.

S&F 100 mm size stainless steel bright finish handle for cabinet shutter complete all as specified & directed.

M&L Frame work as in door chowkhat with angle iron welded together ends of angle shouldered and fixed to opening and welding 3 Nos 100mm sixe mild steel cold rolled butt hinges, and 6 nos hold fasts made out of FI 25x3 mm 30 cm long for fixing of chowkhat complete all as specified and directed

Taking down cement plaster, terrazzo dado in any thickness from brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc including removal of rubbish, vegetation etc outside complex (MOD land) complete all as specified and directed.

M&L Rendering 5mm thick plastering in cement mortar 1:3 as in ceiling finished even and smooth without using extra cement to match with existing surface complete all as specified and directed.

M&L Rendering 12 mm thick in cement mortar 1:6 on fair face of brick work/ concrete surfaces (either surfaces) of wall and finished even and smooth without using extra cement complete all as specified and directed.

M&L Rendering 5 mm thick in cement mortar 1:4 laid over a layer of 10mm thick rendering in cement mortar 1:6 on fair face of brick work/ concrete surfaces of wall with water proofing admixture in topping layer @ 2% Wt of cement finished even and smooth without using extra cement complete all as specified and directed. (WPC will be measured and paid separatly)

Supply only liquid water proofing compound complete all as specified and directed.

Preparation of new plastered surface or old treated surface of wall by applying 2mm thick wall care putty and making the surface smooth and applying two coat of oil emulsion distemper using roller for painting complete all as specified & directed.

M& L preparing plastered new surfaces of ceiling and applying three coats of white wash on ceiling surface

All as per ser item no.78 above but two coat on ceiling surface.

M&L Preparation of newly/old plastered surfaces of walls and applying two coats of colour wash on walls complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connections, including cleaning and refixing old steel tubing and connections in new or old position (Walls, ceiling, floors, etc.)

All as per item No 81 but 20mm bore

S&F 15mm bore GI tubing medium grade with all fittings and fixed to wall and ceiling concealled or laid in floors etc complete all as specified and directed.

All as per item No 83 above but 20 mm bore.

M&L for cutting chases on brick or concrete surface for concealed water tubing or girth n.exc 10cm including making good of disturbed surfaces with PCC 1:2:4 type B0 using 12.5 mm graded aggregate and cement mortar 1:3 complete all as specified and directed.

Dismantling of RCC/ PVC water tanks exc 250 liters and n.exc 500 liters capacity of any condition or type complete all as specified and directed.

S&F white colour Rotational moulded polyethylene water storage tank 500 liters capacity, ISI Marked white triple layer construction (cylindrical vertical closed top), hoisted & fixed in position including inlet/outlet nipple all fittings ISI Marked complete all as specified and as directed.

S&F in repair Gun-metal globe or gate valves 20mm bore with iron wheel head, screwed both ends for iron complete all as specified and directed.

S&F 20 mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed (Minimum weight 210 gms) complete all as specified and directed. Sprarsh Pearl Mod No BCC-302

S&F in repair vitreous chinaware coloured wash hand basin (WHB) size 550mm x 400mm, Ist quality, including provision of pair of mild steel angle iron brackets of suitable size duly painted and cutting for and pinning in ends of brackets in walls & making good & including providing and fixing of suitable heavy duty waste pipe and waste fitting complete all as specified and directed.

S&F in repairs PVC duel action symphonic action type flushing cistern 10 ltr capacity, low level, white with inlet, ball valve and float including brackets and flush pipe complete all as specified and directed.

S&F in repair sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed.

S&F sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe,overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm Complete all as specified and directed.

S&F in repair brass tubuler towel rail, 25mm dia,'D' type 60cm long between flanges of brass cat part PTMT fixed with brass screws complete all as specified and directed .

M & L for PCC 1:2:4, Type B0, using (12.5mm graded aggregate) as in coving over chajja including using 2% water profing compound by weight of cement , finished even and fair complete all as specified and as directed.

S&F in repair Stainless steel cromium plated Soap dish of sixe/cat part No as directed and fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F in repairs 15mm bore Pillar tap of brass Chromium plated high pressure screwed for iron pipe and fixed etc. complete all as specified and directed.

Supply and fix glass corner shelf fancy type made of 6 to 7 mm thick sheet glass of size 250mmx250mm of approved shape fixed with chromium plated brackets complete all as specified and directed. Make : fortune or equivelent

S&F Stainless steel 4 shelf wall mounted kitchen utensils rack, Dish rack with plate,& cutlery stand of size 24"x24" (inches), fixed to wall plugs and chromium plated brass screws complete all as specified and directed.

S & F in repairs vitreous china wash down water closet pan (Pedestal pattern) white incl 'P' or 'S' trap (Make : Parryware/Hindware) and making good the disturbed surface to match with the existing complete all as specified and as directed.

S & F Magic eye piece to door shutter complete all as specified and directed.

S&F in repair stainless steel peg set of six complete all as specified and directed.

S&F in repair 15 mm dia stop cock/angle cock cast copper alloy chromium plated screwed down high pressure with crutch or butterfly handle,with long shank and cup (concealed type), flench screwed both ends for iron or for union.fixed in repair (make: Cera new cat no F2002201, Jaquar cat no CON-CHR-053 KN, Pearl cat no ARI-004 ) . sparsh pearl Mod No ACC-320

S&F in repair bib taps brass cromium plated 15 mm bore size screwed down screwed for iron pipe or for brass ferrule (make: Cera cat no F1015151, Jaquar cat nocontinental CON-CHR-047 KN, Pearl cat no ARI-003 ) Sparsh Prarl Mod No Nova-2400

S&F in repair Stainless steel grating 100mm dia of best quality as approved by GE including fixing in CM 1:4 to floor/nahani traps etc complete all as specified and directed.

S&F in repair PVC connection 15 mm bore and 45cm long with brass check nuts washers complete all as specified and directed. Make Sprrsh Pearl Mod No CPS-153 & Equipment

Supply and fix MS rolled section as in fixing for cooler stand and like fixed with angle iron cleats including making suitable holes in brick work / concrete and filling with PCC 1:2:4 type B0(using 12.5mm graded stone aggregate and finishing with cement mortar 1:3 complete all as specified and directed. Note : Weight of Mild steel section only be measured for payment.

S & F 25mm Stain steel curtain rod covered with fancy type braket and end caps complete all as specified and directed.

S&F 25mm thick factory made Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised with width of flap 40mm complete all as specified and directed.

S&F 100 Hasp and staple, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws complete all as specified and directed.

M & L for cutting of bushes small trees (Peepal small plants etc) trunks shrubs of any dia and girth from roof projection, chajjas , wall junction parapet etc at any height by necessary demoliton of brick work etc if requried and making good distrubed surfaces to match with existing finishes with and incl material and labour in CM 1:4 mixed with WPC /PCC 1:3:6 type B0 /Bk work in CM 1:4 as required at site and as directed by Engr-in-Charge

Supply and fixing PVC heavy duty waste pipes of 40/32mm bore suitable for wash hand basins/sinks/flushing cistern complete all as specified & directed. Make Sparsh Pearl Mod No WP-129 & Equipment

Taking down old existing water proofing treatment from the top of RCC / arch slab, including taking down exsiting PCC padding or plaster and hacking the top of RCC slab, cleaning with water and disposal of rubbish off the premises complete all as specified and directed

Supply and laying sand (25 mm thickness ) for cushioning to interlocking paver block complete all as specified and directed.

M&L for 60 mm thick Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of M-35 Grade made with grey cement and pigment complete all as specified and directed (Make:-ECO/KRISHNA) .

S & F Health Faucet 8 mm dia 1.2 mtr long flexible tube & wall hook complete all as specified and directed (Model : ALD-573, Make : Jaguar OR EQUIVALENT RANGE OF MARC, JOHNSON) / Sparsh Pearl Mod No HF-133

Dismantling of floor of WC and bath not exc 300mm deep and removing out the cinder/concrete from sunken portion, cleaning of RCC surface to remove dust, loose particle with compressed air or any other suitable method depending on site conditions, grinding any sharp edges etc complete all as specified and directed. (b) Cleaning of RCC surface to remove dust, loose particle etc with compressed air or any other particles or any other suitable techniques on site conditions etc.(c) M&L for a glass fiber reinforced acrylic modified cementitious coating system with base coat @ 1.50 Kg/Sqm glass fiber reinforcement and top coat with Sika Top® Seal-107 @ 1.50 Kg/Sqm or equivalent of Fosroc or MC Bauchemie India Pvt Ltd.(d) M&L for protection plaster 15mm thick in cement mortar 1:3 admixed with appropriate integral water proofing compound with as specified by manufacture.(e) M&L for providing 25mm dia GI pipe spout projecting at least 150mm beyond outer face of wall.(f) M&L for sunken portion filled with 40 mm graded brick bats and finished with 50 mm thick PCC 1:2:4 type B1 all as specified and directed.(g) The area of Each WC portion is n.exc 2.00 Sqm each.(h) Cost of the above aspect shall be deemed to be included in the quoted rates of the respective item and nothing extra shall be paid on this account.Note : (i) The work will be executed by authorised manufacturers/applicator. (ii) Plan area only be measured for payment purpose.

S & F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm complete all as specified and as directed.

preparation of new /old plastared surface of walls by appying 2mm thick wall care putty and appying 2 coats of weather coat paint and approved make over a coat of primer complete all as specified and directed.

S&F factory made mild steel shutter shall be made out of angle iron 35x35x5mm, 1 for outer frame and 3 nos 25x25x3mm as cross support in frame of door and covered with 1.00mm thick MS sheet, running welding with frame, with locking arrangement including two coats of synthetic enamel paint over a coat of red oxide primer as shown on drawing all specified and directed by Engr-in -charge.

S&F stainless steel grade 304 grill made of 12mm square hollow SS tube section including welding, grinding buffing & polishing fixed to Aluminium window complete all as specified and directed.

Supply and fix pressed steel frames for doors with one or more rebates including necessary fittings , lugs hinges, lock strike plates etc completed, size of frame 105 x 60mm made out of 1.25mm thick MS sheets including PCVC 1:2:4 type B0 filling as in frame complete all as specified and directed

S & F brass CP mixer ( basin mixer) for mixing hot & cold water screwed down for 15 mm dia iron pipe complete all as specified and directed (Model : 8951 Make : Prayag OR EQUIVALENT RANGE OF Jaquar, JOHNSON). Sparsh Pearl Mod No Nova 2416

S & F plastic water closet (EWC) seat cover white closed pattern with flat bottom and cover incl mild steel chromium plated hinging device complete all as specified and directed. (Make : Parryware/ Hindware). Sparsh Pearl Mod No SC-020

Taking down copper/aluminium point wiring (light, fan, socket or power) complete incl fixtures and fittings suze as swithes, ceiling rose, pendant, regulator, ssockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (Credit for above items should be as per conditions separately) and making good disturbed surfaces of walls, floors etc

M & L for concealed Point wiring with 1.5 Sqmm(Nominal area) PVC insulated, unsheathed FRLS multi stranded copper conductor single core cable 1100 Volt grade drawn through and including PVC conduit of 20 mm dia ISI marked with complete accessories, including modular type galavanised iron steel sunken boxes suitable for switches, sockets, also including PVC insulated and unsheathed single core multi stranded copper conductor cable of size 1.5 sqmm green in colour as earth continuity conductor connected to common earth dolly, including taking down of existing point wiring and their connected fittings & fixtures like switches, sockets, Ceiling rose, fan regulator etc and making good disturbed surface with white wash or any type distemper as per existing colour of building complete all as specified and directed for the following :- Note for Point wiring:- (i) The quoted rate deemed to include the price of G I sunken box,hylam sheet for fixing switches, sockets etc of any size & shape.

(a) One light / fan / exhaust fan / bell point controlled by one one way switch

(b) One light point controlled by one two way switch

(c) One 3/5 pin socket outlet 5 Amp on the same board with other swithes.

(d) One 3/5 pin 5 Amps socket outlet on independent board.

All as per item No 2 above but with 2.5 Sqmm (nominal area) FRLS cable PVC for the 15 Amp 3/5 pin socket power point including 2.5 Sqmm copper conductor green as colour for earth continuity all as specified & directed.

Taking down old sub main wiring and S & F Sub main wiring with two runs of single core FRLS PVC insulated and unsheathed multistranded, copper conductor cable of size 6.0 sqmm LT, 1100V grade, down trhough and incl adequate sizes PVC non metallic conduit of 20mm/approprite dia with accessories and fittings and one run of 6.0 sq mm single core multi stranded copper conductor cable as earth continuity conductor. Two runs of cable one run of earth wire and one run of PVC non metallic conduit of 20mm/approprite dia shall be measured as one run length, Cable required for connection to DBs shall deemed to be included and shall not be measured separately. Earth wire shall run inside the conduit pipe (Note :- Extra length of cable required for connection to MCBs shall deemed to be included in unit rate.)

S&F switch piano flush type polycarbonate single pole one way 5 Amps all as specified & directed. Make: Havells / Anchor (Penta) / Legrand

S&F switch piano flush type polycarbonate single pole one way 15 Amps all as specified & directed. Make: Havells / Anchor (Penta) /Legrand

S&F switch piano flush type polycarbonate single pole two way 05 Amps all as specified & directed. Make: Havells / Anchor (Penta) /Legrand

S&F socket outlet polycarbonate 2 in 1, 3 pin 5 Amps flush type all as specified & directed. Make: Havells / Anchor (Penta) /Legrand

S&F socket outlet polycarbonate 2 in 1, 3 pin 5/15 Amps flush type all as specified & directed. Make: Havells / Anchor (Penta) /Legrand”

S&F Bell Push switch piano flush type polycarbonate, all as specified & directed. Make: Havells / Anchor (Penta) /Legrand”

S&F Bell electric Ding-dong type single phase, operated on 230 Volts. Make: Cona / Anchor / Havells

M&L for Ceiling rose in poly carbonate 3 terminal brass flush type 6 Amps,250 volts AC ISI marked, fixing on 3 mm thick sunmica hylam plastic laminated round sheet 75mm dia complete all as specified and directed. Make: Havells (ROHS)cat part No . AHLHXCW000 or equivalent in Anchor (Penta) /Legrand

S&F electronic fan regulator 230 volts , step type (5 step) socket type ,hum free 100/300 watt complete all as specified and directed. Make: Anchor(Penta) / Havells(REO) / Legrand

Supply & Fixing Angle holders (metal ring) PVC / polycarbonate type B-22 with back plate, complete with LED bulb 12 watts all as specified and directed. Make: Havells(ROHS) or equivalent in Anchor( Penta)/ Legrand

Supply and fix in replacement of old unserviceable LED T5 tube light fitting 20 watts with aluminium housing and polycarbonate diffuser with integrated electronic driver with all accessories including connecting up with pvc insulated and pvc sheathed twisted three core flexible copper wire of 0.5sqmm from ceiling rose to connector of fitting complete all as specified. Make : Bajaj Cat No- BCLAB20WLEDP,Havells Cat No- LUMILINEPLUSBS20WLED865SPCSS, Crompton Cat No- CCS1002065HL2DPNWH

S & F In replacement of old unserviceable light fittings LED tube light fitting Integral 9/10watts LED Tube light fitting internally prewired and incl connecting up with two core wire od suitable size complete all as specified. Make as per Havells Cat No.-LUMILINEBS9WLED865SPCWH, Wipro Cat No- D571065, Eveready Cat No-LBT-10SQ.

S & F In replacement of old unserviceable Building security light fitting versatile pressure die-cast aluminium with high power LED 30 W as light source complete with LED 30 W 5700K including brackets made out of GI pipe light grade pipe bent to shape incl 02 Nos MS flate clamps incl nut bolts connection complete all as specified and directed . Make : Eveready Cat No-LEDSL03015-PC, Crompton Cat No-TRP-400-30-57-SL-LM-NSR, Havells Cat No- ENDURAPEARLSL30WLED757SASYTOPCMP

S & F In replacement of old unserviceable bulk head light fittings with new LED bulk head IP 65 with prismatic diffuser 1x10 Watt including LEB bulb 10/12 watts white complete with all accessories internally prewired and incl connecting up three core single wire complete all as specified and directed . Make : Eveready cat part No. LEDBK01015-01, Crompton Cat No-LBHP-10-CDL, Havells Cat No-HEXAFT10WLED857SSYMBOPC

S & F In replacement of old unserviceable Distribution board (DB) made out of sheet metal enclosure (CRCA sheet) dust and vermin proof SPN 8 way IP 43 (double door) with 200 Amps rated copper bus bar neutral bar ,earth bar ,single pole and neutral 250 volts ,flush to wall complete all as specified and directed Make-Legrand / ABB / Havells

S & F in replacement of unserviceable TPN DB- VTPN for independent mounting fixed on wall, flush mounted, 4 way, IP 43, IK 09 with 250 Amp Bus bar complete all as specified and directed. Make - Legrand Cat No-5077 45 or L&T Cat No - DBVTL004DD or INDOASIAN Cat No - 811888

S & F in replacement of unserviceable MCCB 100 Amp four pole, 415 volt, 16kA fixed overload and fixed short cicuit setting, including necessary connection complete all as specified and directed by Engr-in-Charge.

S & F In replacement of old unserviceable MCB single pole, 6 to 32 Amp 240 volt, 'C' curve complete all as specified and directed . Make-Legrand / ABB / Havells

S & F In replacement of old unserviceable MCB single pole and neutral, 63 Amp,10kA 240 volt, complete all as specified and directed. Make-Legrand/ABB/Havells

Supply, Installed & fix maintenance free earthing copper bonded steel earth rod of 10 feet long having diameter of 17.2mm with copper bonding thickness of 250 micron,UL listed,CPRI Tested at 25 KA fault current for one second and is provided with universal clamp made of SS earth enhancing compound shall be of 30kg/pit(resistivity is less than 0.12 Ohm meter) tested as per IEC 62561-7.The above arrangements shall be provided with heavy duty earth poly plastic pit cover of 6000 kg load bearing capacity (Size:270 x 240 x 200mm) and FRLS insulated copper conductor of size 6 sqmm, single core cable drawn through and including suitable dia of medium grade GI pipe upto 7 mtr incl cutting and chases on wall and floor complete all as specified and directed. Note: The rate quoted above shall be deemed to be included for excavation and earth work, refilling, removal of surplus earth and making good the surface around chemical earthing.

Supply, laying & testing XLPE insulated armoured heavy duty electric cable with aluminium conductor, 1100V grade, cross sectional area 4 Core 35 Sqmm, complete all as specified and directed by Engr-in-Charge.

Excavation in trenches in soft/disintegrated soil not exc 1.5 m wide and not exceeding 1.5m in depth for laying UG cable/foundation etc complete all as specified and directed.

Returning filling in soft/disintegrated soil including spreading levelling watering and well ramming in layers n.exc 25cm each layer complete all as specified and directed.

Removal of excavated surplus soft/disintegrated soil to a distance not exc 50 mtr and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified and directed.

Supply and laying clean dry river sand for cushioning in layers, 8 cm before lying of cable and 15 cm after lying of cable (total 23 cm) in trenches complete all as specified and directed. Note:- Thickness of sand cushioning shall be measured as 18 cm after punning for payment)

Supply and laying old size sub class ‘B’ bricks for cable protection, laid dry flat adjacent to each other across the length of cable complete all as specified and directed.

S&F in replacement, 32mm dia bore GI tubing, light grade with all fittings for cable protection including GI clamps, nut & bolts and washers or burried in ground complete all as specified and directed.

Supply and fixing Geyser horizontal type, as per site requirement, of capacity 25 litres, Single phase, 240 Volts, with auto cut-off and adjustable temperature including making fixing arrangement on existing wall with 15mm bolt fastner of suitable length-04 Nos, PVC connection pipe 600 mm long, including cooper connector, PVC connector and 01 plug top 15 Amps complete all as specified and directed. Make : Havells / Bajaj / Recold

Supply and fix modular MCB protected plug and socket board in sheet steel enclosure with 25 Amp MCB and 3 pin plug, 240 V, 50 Hz complete including cutting the wall surfaces for flush mounting of socket board and making good with cement plaster, putty and paint to match with the existing surface complete all as specified and directed.

Supply and fix Angle valve 15mm bore, chromium plated, screwed ,cast copper alloy, with capstan heads, for iron pipe, complete all as specified and directed .

Supply and fix ceiling fans (BLDC) without remote complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with BEE, Five star rated with brushless direct current motor, complete all as specified and directed.

M&L for making ceiling fan hook made out MS flat iron of size 40mm x 5mm, suitable for hanging ceiling fan, complete all as specified and directed.

M&L for 40mm dia bore MS pipe, medium grade including painting with white synthetic enamel over a coat of primer and grouting in walls, making good to disturbed surface to match with existing finished walls, complete all as specified and directed.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers. including making suitable size of holes in wall for fixing the fan & making good including making electrical connection with ceiling rose, complete all as specified and directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm, including making suitable size of holes in wall for fixing the fan & making good including making electrical connection with ceiling rose, complete all as specified and directed.

M & L for Circuit/submain wiring with single core FRLS PVC insulated copper stranded conductor cable drawing into existing PVC rigid conduit surface /concealed/ casing caping as required at site, of size 1.5 Sqmm for Inverter wiring, including taking down unserviceable existing wiring etc complete all as specified and directed.

M/s MAA SHAKTI CONSTRUCTIONS AND SUPPLIERS

nautiyalandcompany

M/S MSD & Associate

AMAR NATH SHARMA

M/S TRIVENDRA KUMAR

AMAN MATERIAL AND LABOUR CONTRACTOR

Mudit Interior and Developer

M/s Chitter Mal & Co.