Construction of 03 Nos., 2X12.5MVA, 33/11KV substations on Turnkey Basis Including Civil Works And AMC of Project for 5 Years

Amount

MS Round 32mm dia 6.21 Kg/mtr for earth mat, electodes for earth mat & delta earthing

GI Angle 65x65x6mm

G.I. strip 65x6mm

G.I. strip 50x6mm

GI Channel 125X65x6mm

GI angle 40x40x5mm

Wire mesh fencing with 4mtr and 1mtr wide gate duly painted on both sides.

33 KV,10 KA Lightening Arrester

33 KV 800 A outdoor Type 3P gang operated complete, off load Isolator with earth switch and suitable for D/P structure mounting operated. (i) Incommer

(ii) Outgoing

33 KV Polymer Disc insulator B&S type

Disc fitting B&S 120 KN

Rail 90 Lbs

GI angle 50x50x6 mm

MS Bar, 12 mm Dia for Steel reinforcement

T/F 33/11 KV 12.5 MVA

GI angle 75X75X8 mm

33 KV Fuse Set

GI bolts & nut with washers.

G.I. Plate 300x300x8 mm.

33 KV/110 V O/D type PT

Junction box for 33 KV PT

G.I. Plate 400x400x8 mm.

ST pole SP- 33, 9.0 mtr long (Bottom portion hot dip galvanised)

Earthing rod 20x2500mm

33 KV Aluminium 3Cx50 sq. mm. XLPE

LT XLPE Cable 3.5x70 Sq.mm. for Stn. T/F to ACDB.

ACSR Dog conductor

33/0.433 KV, 63 KVA Station Transformer

G.I. Channel 100x50mm

33 KV off load Vertical type isolator

G.I./MS Bolt & Nut off size

PP clamp with bolts & nuts made by GI

G.I.Strip 35x4mm

Alu lug for T/F HT & LT side.

PG clamp for Panther to Dog Conductor

PG clamp for Bus isolator,Fuse Set suitable for Dog Conductor

Clamp of required size for holding cable supporting channel, pipe, cable etc.

Name plate for station transformer with clamp, nut & bolt

33 KV Danger board with clamp

Stone Pad 300x300x75

GI pipe 4" dia. 3mtr long

Cable jointing kit outdoor type suitable for 3Cx50 sq. mm. XLPE cable 33 KV.

S.T. Pole 11 mtr. Long SP-55 (Bottom Portion hot dip Galvanized)

11 KV Polymer disc insulator B & S

11 KV disc fitting for Rabbit/weasal

11 KV TPMO complete

Stay Set GI 16x1800mm

Stay wire 7/10

GI Wire 6 SWG

9KV 5KA lightening arrestor (Polymer)

11 KV fuse set.

Stay clamp for ST Pole

Clamp of required size for holding cable supporting angle, cable & TPMO handle

Name plate of feeder

11 KV Danger board with clamp

36 KV, 1250A Gang operated, Permanent Magnetic actuator operated outdoor compact, V.C.B. including in-built epoxy resin cast dry type CT both side bus bar etc. (SCADA OPERATED) (i) Incomer

(ii) Outgoing

Control & Relay Panel with SCADA operated and relay for 33 KV (i) Incomer

(ii) Outgoing

12 KV, 1250A Gang operated, Permanent Magnetic actuator operated outdoor, compact, V.C.B. including in-built epoxy resin cast dry type CT, PT both side bus bar etc. (SCADA OPERATED) (i) 12KV, 1250 A, 26.3KA/3 sec.(BIL 38/95 KV). For Incomer

(ii) 12KV, 1250 A, 26.3KA/3 sec.(BIL 38/95 KV). For outgoing feeder

(iii) 12KV, 1250 A, 26.3KA/3 sec.(BIL 38/95 KV). For capacitor Panel

(iv) 12KV, 1250 A, 26.3KA/3 sec.(BIL 38/95 KV). For Bus coupler

Control & Relay Panel with SCADA operated and relay for 11 KV (i) For Incomer

(ii) For Feeders

(iii) For Capacitor Panel

(iv) For Bus coupler

Cable Aluminium 3Cx400 sq. mm. XLPE 11KV

11 KV 1Cx630 Sq mm AL XLPE cable

Cable jointing kit indoor type suitable for 3Cx400 sq. mm. XLPE cable 11 KV

33 KV alluminium cable 1Cx630 sq mm XLPE

33 KV cable jointing kit 1Cx630 sq mm O/D type

33 KV cable jointing kit 1Cx630 sq mm I/D type

Cable jointing kit outdoor type suitable for 1Cx630 sq. mm. XLPE cable 11 KV

Cable jointing kit indoor type suitable for 1Cx630 sq. mm. XLPE cable 11 KV

HT Cable warning tape

GI pipe 6" dia, 3mtr long

Clamp of MS Flat 50x6 mm. of suitable size for holding 6" & 4" dia. Pipe

PG Clamp for L.A.

10C x 2.5 Sq. mm. LT Control Cable

4C x 2.5 Sq. mm. LT Control Cable

2C x 2.5 Sq. mm. LT Control Cable

MS Angle 50x50x6mm for cable trench

MS Angle 40x40X5mm for cable trench

MS Bar, 10 mm

(i) 400 mm width Perforated tray for cable trench

(ii) 200 mm width Perforated tray for cable trench

(iii) 100 mm width Perforated tray for cable trench

8mtr long ST pole SP-10 (Bottom portion hot dip)

LT PVC cable 4x10 sq. mm.

LT PVC cable 2x6 sq. mm. armed

Iron clad 30 Amps water proof switch on the ST pole.

250W LED lamp with control gear & mounting accessories

DC Distribution box

24 V DC 200 Amp hr Lithium Battery Li,Fe P04 Battery Pack

Float cum boost cum inverter 24V with Trickle Charging arrengment with all meters AC/DC

Instruction board 3’x2½’ of Flex board duly printed.

Single line diagram of size 3’x2½’ on flex board, duly printed.

Maximum & tripping display board of size 5’x3’ of mica board moulded with frame duly painted & writing.

Sub-station named board (Size 3'x2' of MS sheet & MS angle 45x45x5 mm, Height 1.5 mtr. Above ground level ), duly painted

Name plate of equipment TG, LI, BI, PI, BG, CT, PT, CB, LA etc. (Size 9"x5" with white base, red border & letter written in red color)

Sundries items Cable tie, Alu lug, Copper lug & HT, LT tape, pvc compound, ferrule, pvc flexible pipe, paint writing on panels, HT LT diff size cable gland.

IP CC TV camera 8 nos with monitor (AI based)

Steel office table of size 5'x3' reputated company make

Steel office table of size 4'x2.5' reputated company make

Steel Almirah reputated company make

Steel cabinet reputated company make

Steel office chair reputated company make

1400 mm sweep ceiling fan with Regulator

Padestal fan

Doormat (5'x3')

Dust bin

Shock treatment chart

Danger board

Shut down / Break down board (Bi-lingual Hindi & English)

HT Hand Gloves

Wall Clock

Insulated electrical Plier Taparia

D-Spanner Set Taparia

3 cells Torch

Pipe wrench, 12" Taparia

First aid Box

Earth chain brass 12 mtr. Length

5 KV Megger Digital reputated company make

2.5 KV Megger Digital reputated company make

Earth Megger Digital reputated company make

Rubber mat 1 mtr. wide x 2 mtr long and 12 mm thick to withstand 11 KV dielectric strength as per IS 5424-1969 along the all equipments in Control Room.

Carbon dioxide (CO2) type fire extinguishers conforming to IS 2878 - 1976 and cylinders fully charged of 4.5 Kg capacity.

Foam type fire extinguishers, Portable type 5 lit capacity hanged on wall with bracket complete as required

Metal Fire bucket Filled with sand

Fire bucket stand of Chuggi type of MS angle 50x50x6 mm with top covered by MS sheet 2 mm. thickness and Duly painted with red color including cost of all material, fabrication etc. complete work

9KV, 10KA lightening arrestor

LT Control Cable 6C x 2.5 Sq. mm.

Cable Aluminium 3Cx120 sq. mm. XLPE 11KV

Cable jointing kit outdoor type suitable for 3Cx120 sq. mm. XLPE cable 11 KV

Cable jointing kit indoor type suitable for 3Cx120 sq. mm. XLPE cable 11 KV

12.65KV 4800 KVAr 3 phase 50hz housed in outdoor type IP 5X CRCA Panel Capacitor bank having seven variable step of 150+300+450+600+ 900+1200+1200 KVAr tobe insttaled at substation. Bank shall be complete with capcitor unit of 400/300/200/150/100/50 Kvar, alluminium bus bar, Pin & post insulator, HRC fuses etc outdoor type CRCA panel shall be accomodating capacitors, series reactor, vaccuum contractor, surge succsessor, fuses, RVT etc.

11KV,630Amp off load Isolator with earth switch and mounting structure

Indoor type automatic power factor controller pannel for seven step

Lugs/thimble junction box, 2 nos cable support structure etc.

Cable box of 2mm thick CRCA sheet of dimension 1000x600x500mm (HXWXD) with associated accessories like bus bars,insulators,holding clamp for cable etc.

CT outdoor with mounting structure (1Set=3 Nos)

GI Earthing strip 35x6mm

ACSR Panther conductor

Disc fitting B&S type 90 KN for Panther

PG clamp Panther to Panther

PG clamp Panther to Dog

Wedge connector for panther to panther

Wedge connector for panther to dog

Connectors suitable for Panther for Lightening Arrestor

Connectors suitable for Panther for Isolator

Connectors suitable for Panther for 33 KV VCB

Connectors suitable for Panther for 33 KV PT

Connectors suitable for Panther for T/F HT side

Connectors suitable for Panther for T/F LT side

Flexible copper connection on neutral bushing of power & station transformer 500X50 mm heavy duty with copper lug at ends.

M.S. Angle 65x65x6 for bracing set, 2.7mtr.x2

M.S. Channel 100x50mm for top channel & dropper channel & TPMO handle

M.S. Angle 75x75x8 mm for TPMO & Fuse set (4 nos.x2.24 mtr.)

M.S. Angle 50x50x6 mm for cable support 2.24 mtr.x3No

MS plate 300x300x8 mm

P.P. & Clamps for S.T. Pole

MS Channel 125x65 mm

Description of Work / Item(s)

Amount

Erection of Earth Mat & Earthing work of all equipment and structures of 33/11 KV Sub-Station. (i) Excavation of earth

(ii) Straightening and laying of Earth mat of 32 mm M S round 0.6 mtr or 1 mtr deep in mixed soil according to drawing or as per UPCL direction or/and as per site requirement. Making T-joints, cross joint and Lap joints by welding of M S round bar together using cleats of MS Angles 65x65x6 mm, chipping the slag and painting of the joints with black bitumen paint (including supply of paint) to avoid rusting. Cutting & making electrode 2.5 mtr long with conical pointed bottom and driving of the electrode in ground so that the top of electrode remains 450 mm below ground level. Backfilling of soil in trenches, ramming and leveling of trench properly after completion of eartmat and earthing work is complete. Making of Delta/Bridge earthing for structure/panels i.e. 33 KV LA, 11 KV LA, 33 KV panels, 11 KV panels, ACDB, DCDB, Neutral of power & station transformer.

(iii) Fabrication of GI items

(iv) Earthing of structures using G.I. strips including strengthening, cutting, bending & welding with structure and equipments.

(v) Special earthing by treatment of soil with highly conducted material like combination of bentonite, conductive cement, coke dust, sodium carbonate, MgSo4, NACL & CaCL2 as per ISS 3043-1987.

(vi) Earthfilling in yard

(vii) Supply and spreading of 75mm thick layer of Gravels of size 20mm to 25mm.

Construction of Toe wall and fixing of wire mesh fencing around the switch yard. (i) Excavation of mixed soil

(iii) RR 1:6 below ground level

(iv) CC 1:2:4 on top of RR masonary

(v) Brick work, 1:4

(vi) Cement Plaster 1:4

(vii) Fabrication and Erection of stays post of 40x40x5 mm angle 2.5 mtr long. with required CC 1:4:8 work of size .5x.5x.5

(viii) Fabrication & Erection of RS Joist 175x85x6mm for fixing of wire mesh gate including grouting of the pillar.

(ix)Erection of wiremesh fencing with 4mtr and 1mtr wide gate.

Febrication and erection of 33KV Terminal Gantry. Febrication and erection charges of 33KV Terminal D/P 8.5mtr long of RS joist 150x150mm with double top channel GI 125x65mmx3.2 mtr with bracing set and suitable channel mounted for fixing 33KV Vertical isolator and Lightening arrestor including supply of all materials.

Febrication and erection of 33KV Bus Gantry. Febrication and erection charges of 33KV Bus D/P 8.5mtr long of RS joist 150x150mm with double top channel GI 125x65mmx3.2 mtr with bracing set and suitable channel mounted including supply of all materials.

Construction of Power Transformer Plinth. (i) Fabrication of Rail 90 Lbs, cutting of GI angle 50x50x6 mm and MS Bar 12 mm

(ii) Excavation of earth in mixed soil

(iii) CC 1:4:8

(iv) Brick work in 1:4

(vi) Plaster in 1:4

Erection and Fixing of Power Transformer on Plinth. (i) Shifting of transformer from road side to transformer plinth through chain pully, lift pully and slippers etc.

(ii) Erection of transformer by fixing all accessories, tank, filling of transformer oil etc.

(iii) Fabrication & erection of neutral structure including excavation & grouting in CC 1:4:8

Erection and fixing of 33 KV Fuse Set. (i) Fabrication charges of structure as per approved drawing

(ii) Excavation of earth in mixed soil

(iii) Grouting of structure with C.C. in 1:3:6 ratio

(iv) Cement Plaster 1:4, on top & side walls

(v) Erection charges of structure

(vi) Fixing and erection charges of Fuse set

Erection and Fixing of 33 KV Lightening Arrestor. (i) Fabrication charges of structure as per approved drawing

(ii) Excavation of earth in mixed soil

(iii) Grouting of structure with C.C. in 1:3:6 ratio

(iv) Cement Plaster 1:4, on top & side walls

(v) Erection charges of structure

(vi) Fixing and erection charges of Lightening arrestor

Erection and Fixing of 33 KV Potential Transformer. (i) Fabrication charges of MS item

(ii) Erection charges of structure

(iii) Fixing and erection of equipments.

Erection and Fixing of 33/0.433KV,63 KVA Station Transformer. (i) Excavation of earth

(ii) Cement concreting of Double pole 1:4:8

(iii) Cement Plaster in 1:4

(iv) Fabrication charges of channels

(v) Erection of Double pole complete with all fittings, channels etc. complete work

(vi) Labour charge for pit digging 0.6mtr below GL for earthing rod making delta for T/F neutral and then welding with GI strip and taking out 1 for T/F Neutral ,1 for T/F Body and 1 for L.A. including cost of welding and N&B.

(vii) Painting of structure with one coat of red oxide paint and two coat of Aluminium paint of best quality I.S.I. mark Dulux, Burger, Asian make including cost of red oxide, paint.

(viii) Erection of 33/0.433 KV station transformer on double pole with all accessories complete work

(ix) Laying, spreading & jointing of LT cable by using propers ties, lugs, connectors, cable glands in cable trench and equipments..

(x) Digging open trench 120cm deep and 45cm wide and prepare 10 cm thick fine sand cushion and then Laying of 33KV 3X400Sqmm cable over this cushion,then covered the cable with another 10cm thick sand layer.The trench is then covered with brick and other material covering all around cable protected on sides and top as per site requirement.

(xi) Filling/Fixing of cable jointing kit 33 KV indoor and outdoor type

(xii) Erection of vertical 33 KV isolator on double pole SP-33 complete by assembeling, fixing of operating handle, pipe, clamps, pins etc for smooth operation of the isolator.

Erection and Fixing of Double Pole Structure of outgoing 11KV Feeder. (i) Excavation of earth

(ii) Cement concreting of Double pole 1:4:8

(iii) Cement Plaster in 1:4

(iv) Fabrication charges of channels & angle

(v) Erection of Double pole complete with all fittings, accessories, stays & earthing.

(vi) Painting of structure with one coat of red oxide paint and two coat of Aluminium paint of best quality I.S.I. mark Dulux, Burger, Asian make including cost of red oxide, paint.

Erection and Fixing of 33 KV Circuit Breaker and C&R Panel. (i) Cartage of all panels from road side to SGR

(ii) Placing of panels on specific place over SGR trench on MS Channels and fixing of pannels with nut & bolts.

(iii) Making electrical connection of panels by control wiring complete with & VCB etc.

Erection and Fixing of 11 KV Circuit Breaker and C&R Panel. (i) Cartage of all panels from road side to SGR

(ii) Placing of panels on specific place over SGR trench on MS Channels and fixing of pannels with nut & bolts.

(iii) Making electrical connection of panels by control wiring complete with & VCB etc.

Laying of 33KV/11KV XLPE Cable. (i) Laying of 33 KV/ 11 KV Cable by excavation of cable trench in mixed soil, filling of the sand upto the height 250mm from the bottom most level of the cable trench thereafter properly laying of the cable by placing bricks on both side of the cable than re-filling of the sand from the top so as to cover the cable completely and then placing the bricks on the top of the covered cable, spreading of cable warning tape & covering of the trench completly with mixed soil including cost of sand, bricks, etc.

(ii) Filling of cable jointing kit 33 KV indoor & outdoor type

(iii) Filling of cable jointing kit 11 KV indoor & outdoor type

(iv) Fabrication charges of MS items

(v) Fixing of GI Pipes

(vi) Erection of cable supporting MS Channel & angle

Construction of cable trench and laying of LT control cable. (i) Fabrication charges of MS item

(ii) Making cable trench including fabrication, fixing of MS angle 50x50x6 mm size (excluding the cost of MS Angle/ MS bar) on side edge with all excavation, CC work, brick work, fixing of cable support angle one/two tier as required with stopper arrangement at 0.5 mtr gap throughout the length of the trench, making of cable trench covers with MS Bar welded mesh angle frame of MS angle 40x40x6 mm. with lifting hooks, fixing of perforated tray complete as per drawing including cost of sand, cement, bricks, metal (gitti) etc.

(iii) Laying, spreading & jointing of LT control cable by using propers ties,lugs, connectors, cable glands in cable trench and equipments..

Fixing and Erection of Lights at Yard and S.G.Room. (i) Excavation of earth

(ii) Cement concreting in 1:4:8 ratio

(iii) Erection of ST Pole SP-10 and fitting of accessories.

(iv) Painting of ST Pole with one coat of red oxide primer and two coat of Aluminium paint.

(v) Erection of 250 watt lighting equipment & all its accessories

(vi) Laying of LT PVC cable 4x10 sq. mm. in soil & back filling of sand.

Fixing, placing and erection of Misc Items. (i) Erection of 24 V Battery Set

(ii) Erection of Battery Charger

(iii) Erection of DCDB

(iv) Erection of ACDB

(v) Erection of Name plates, instruction board, SLD, Max., Min. board etc.

(vi) Erection of substation name board by grouting in CC 1:4:8 ratio

(vii) Erection & fixing of CCTV camera including required material for complete work

Fixing, placing and erection of T&P and furniture material

Installation/Mounting of Fire Extinguishers

Erection and Fixing of 11KV Capacitor Bank. Civil work (including foundation,plinth of capacitor cubical etc as per RESPO Drawing) (i) Earth work

(ii) Brick work 1:6 Sub Structure

(iii) Brick work 1:6 Super Structure

(iv) Cement plaster 1:6 (12mm thick) on plinth

(vii) CC 1:1.5:2

(viii) Steel Reinforcement

(ix) Fixing and erection of capacitor bank with complete accessories.

(x) Fixing and erection of 11KV,630Amp off load Isolator with earth switch and mounting structure

(xi) Filling of cable jointing kit 11 KV indoor & outdoor type

Cable trench in size 30x20cm for laying of power/control cable including cost of all material.

Laying of power and control cable in trench including all connections.

Supply & fixing of electrode chemical earthing and GI strip 50x6 mm for equpments

Erection and Fixing of Bua Bar & Connectors. (i) Fixing of Flexible copper connection on neutral bushing of power & station transformer .

(ii) Labour charges for drawing bus-bar & making connection in each equipment, main & auxilary bus bar.

Testing of S/s

Description of Work / Item(s)

Amount

Annual Maintenance Charges (AMC) of Project for 5 years on per year basis.

Description of Work / Item(s)

Amount

Construction of S G R Building Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50m. All kinds of soil.

Supplying and filling in plinth with Jamuna sand under floors, including watering, ramming, consolidating and dressing complete.

Supplying and stacking at site.Good earth

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer’s specification.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :sand: 3 graded stone aggregate 20 cm nominal size).1:1.5:3 (1 cement : 1.5coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)C1

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting propping etc. and removal of form for: Foundations footings, bases of columns, etc. For mass concrete.

Centering and shuttering including strutting propping etc. and removal of form for: Suspended floors, roofs, landings, balconies and access platform.

Centering and shuttering including strutting propping etc. and removal of form for: Shelves (Cast in situ)

Centering and shuttering including strutting propping etc. and removal of form for: Lintels, beams, plinth beams girders, bressumers and cantilevers,

Centering and shuttering including strutting propping etc. and removal of form for:. Columns, Pillars, Piers, Abutments, Posts and Struts.

Centering and shuttering including strutting propping etc. and removal of form for. Weather shade, Chaffas, corbels etc. including edges.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:4 (1 cement :4 coarse sand)

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade Area of slab upto 0.50 sqm

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite of any colour and shade Area of slab over 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge Granite work

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.35 mm thick including ISI marked Stainless Steel butt hinges with necessary screwsmatched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hingeswith necessary screws

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete :250x16 mm

Providing and fixing ISI marked oxidised M.S. tower bolt black finish (Barrel type) with necessary screws etc. complete : 200x10 mm

Providing and fixing ISI marked oxidised M.S. tower bolt black finish (Barrel type) with necessary screws etc. complete : 150x10 mm

Providing and fixing ISI marked oxidised M.S. tower bolt black finish (Barrel type) with necessary screws etc. complete : 100x10 mm

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete :125 mm

Providing and fixing aluminium sliding door bolts, ISI marked anodised anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 250x16 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :(200x10mm)

Providing and fixing aluminium tower door bolts ISI marked anodised (Anodic coating not less than grade AC 10 as per IS:1868)transparent or dyed to required colour or shade with nuts and screws etc. complete: (150x10mm)

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :100x10 mm

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :125mm

Providing and fixing aluminium handles floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary scerews etc. complet: Single rubber stopper

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Twin rubber stopper

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.With stainless steel cover plate minimum 1.25 mm thickness

Providing and fixing wire gauge shutters using stainless steel grade 304 wire gauge with wire of dia 0.5 mm and average width of aperture 1.4 mm in both directions for doors, windows and clerestory windows with necessary screws : 35 mm thick shutters with ISI marked M.S. pressed butt hinges bright finished of required size Second class teak wood

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer.

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strikeplate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineerin-charge:Profile B Fixing with adjustable lugs with split end tail to each jamb

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strikeplate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineerin-charge:Profile C Fixing with adjustable lugs with split end tail to each jamb

Steel work in built up tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard rawing.surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete. Galvanised M.S. Wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with :5.5 mm thick glass panes

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate20mm nomnal sxe stone aggregate).

Providing and fixing glass strips in joints of terrazo/ cement concrete floors. 40 mm wide and 4 mm thick

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados,over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 oarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigments etc., complet

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 600x600 mm

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600x600 mm

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. (75mm diameter)

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.( 110mm diameter)

12mm cement plaster of mix: 1:4 (1cement : 4coarse sand)

12mm cement plaster of mix: 1:6 (1cement :6coarse sand)

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water tinnable priming coat with cement primer.

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/ 10 sqm

Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:1½:3 (1 Cement: 1½ coarse sand: 3 graded stone aggregate 20 mm nominal size)

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing terminal guard : 75 mm Sand cast iron S&S as per IS - 1729

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 100 mm inlet and 100 mm outlet Sand cast iron S&S as per IS: 3989

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall : 15 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 15 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 20mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 25 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 40 mm dia nominal bore

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making ecessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.(15 mm nominal bore)

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore 15mm nominal bore

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

P/Fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side

Engazing suitable carpenter for petty works (basic rates labour )

Engazing suitable beldar for petty works ( basic rates labour )

Engazing suitable fitter for electrical works ( basic rates labour )

Construction of S G R Building (For Electrical Items) Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required. GROUP C

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required2*2.5 Sq.M*1*2.5Sq.M

Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including nnections but excluding modular plate etc. as required.

Supply and Installation 1.00HP water pump Havells and equivalent make all compl.as per direction of E.I.

Supply of 1200 mm sweep ceiling fan of approved quality ( Bajaj,USHA, Havells or equilent make) without regulator.

Supplying of Exaust Fan 450 mm sweep of orient or equivalent make as apporoved by E.I

(1.41) Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

(1.50.1)Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required Upto 450 mm sweep

Supply and Installation 1.00HP water pump Havells and equivalent make all compl.as per direction of E.I.

Supply of 20 watt LED Tubelight Philips or equivalent make approved by E.I.

Supplying of Exaust Fan 450 mm sweep of orient or equivalent make as apporoved by E.I

(1.41) Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

(1.50.1)Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required Upto 450 mm sweep

Supply ,Installation,Testing and Commissioning 1200 mm sweep, BEE 5 star rated,ceiling fan with brush less direct current (BLDC)Motor,class of insulation:B, 3 no. blades, 30 cm long down rod ,2 nos canopies,shakle kit,safety rope,copper winding ,power factor not less then 0.9,service value(cmm/w)minimum 6.85,aire delivery minnimum 215 cmm, 350 rpm(tollerance as per IS : 374/219),THD less then 10%,remote of electronic regulator unit 4 speed controll and all remaining accesories including safety pin ,nut bolts,washers,temperature rise equal to75 degree c (max), insulation resistance more then 2 mega ohm ,suitable for 230 v ,50 Hz ,single phase AC supply , earthing etc complete as required.

Construction of boundary wall Earth work in excavation by mechanical means (Hydraulic excavator ) manual means in foundation tranches (not exceeding 1.5m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50m. (All kinds of soil). For wall & pillers

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering -All work up to plinth level:1:4 :8 (1 Cement :4 coarse sand: 8 graded stone aggregate 40 mm nominal size)

Brick work with F.P.S. bricks of class designation 75 in foundation and plinth in: Cement mortar 1:6 ( 1 cement : 6 coarse sand)

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement- All work up to plinth level: 1:2:4 (1 cement : 1.5 coarse sand: 3 graded stone aggregate 20 cm nominal size).

Reinforced cement concrete working beams, suspended floors, roofs having slope up to 1.5 landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral/ stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement with 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting propping etc. and removal of form for: Lintels, beams, plinth beams girders, bressumers and cantilevers,

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. (Cold twisted bars ).

Brick work with F.P.S. Bricks of class designation 75 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 ( 1 cement : 6 coarse sand)

Steel work welded in built up sections/ framed work including cutting, hoisting fixing in position and applying a priming coat of approved steel primer susing structural steel etc. as required. (In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.)

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.( 110mm diameter)

12mm cement plaster of mix: 1:6 (1cement :6coarse sand) In wall

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20kg/ 10 sqm)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved prand and manufacture.

Filling available excavated earth (excluding rock) in trenches, plinth sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5m

Land Development Works (Construction of C.C road ) Earth work in excavation by mechanical means (Hydraulic excavator ) manual means in foundation tranches (not exceeding 1.5m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50m. (All kinds of soil) For Toe Wall

Supplying and filling in plinth with Jamuna sand under floors, including watering, ramming, consolidating and dressing complete. Filling for site

Supplying and stacking at site.Good earth

P/laying in position cement concrete of specified grade excluding the cost of centering and shuttering -All work up to plinth level:1:4 :8 (1 Cement :4 coarse sand: 8 graded stone aggregate 40 mm nominal size)In Yard for turffing

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:4 (1 cement :4 coarse sand)

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate20mm nomnal sxe stone aggregate).

Cement concrete pavement with 1:2:4 including finishing complete. Road c.c.

steel work in builtup sections/framed work in frames,guard bars,railings,gates,similar work.railings

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes (110mm diameter)

12mm cement plaster of mix: 1:6 (1cement :6coarse sand)

Providing and laying 60mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.

Stone Aggregate (Single size) : 20 mm nominal size In Yard

Construction of Collection Room Earth work in excavation by mechanical means (Hydraulic excavator ) manual means in foundation tranches (not exceeding 1.5m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5m, (All kinds of soil). Columns Footing F1

Filling available excavated earth (excluding rock) in trenches, plinth sides of foundations etc. in layers not exceeding 20 cm in depth,

Supplying and filling in plinth with Jamuna sand under floors including. Watering, ramming consolidating and dressing complete. .

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering -All work up to plinth level:1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering -All work up to plinth level:1:4 :8 (1 Cement :4 coarse sand: 8 graded stone aggregate 40 mm nominal size)

Providing and laying damp-proof course 40 cm thick with cement concrete 1:2:4 ( 1 cement :2 coarse sand: 4 graded stone aggregate 12.5 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement .All work up to plinth level: 1:1:5:3 (1 cement : 1.5 coarse sand: 3 graded stone aggregate 20 cm nominal size).

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, posts reinforcement. 1:1:5:3 (1 cement : 2 coarse sand 4 graded stone aggregate 20 cm nominal size). Columns

Reinforced cement concrete working beams, suspended floors, roofs having slope up to 1.5 landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral/ of centering, shuttering, finishing and reinforcement with 1:1.5:3

Centering and shuttering including strutting propping etc. and removal of form for: Foundations footings, bases of columns, etc. For mass concrete. Cols Footings

Centering and shuttering including strutting propping etc. and removal of form for: Suspended floors, roofs, landings, balconies and access platform.

Centering and shuttering including strutting propping etc. and removal of form for: Shelves (Cast in situ)Sheleves bottom

Centering and shuttering incl. strutting propping etc. and removal of form for: Lintels, beams, plinth beams and cantilevers,

Centering and shuttering including strutting propping etc. and removal of form for:. Columns, Pillars, Piers, Abutments, Posts and Struts. Columns

Centering and shuttering including strutting propping etc. and removal of form for. Weather shade, Chaffas, corbels etc. including edges.

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. (Cold twisted bars ).

Brick work with F.P.S. bricks of class designation 75 in foundation and plinth in: Cement mortar 1:4( 1 cement : 4 coarse sand)

Brick work with F.P.S. bricks of class designation 75 in foundation and plinth in: Cement mortar 1:6 ( 1 cement : 6 coarse sand)

Brick work with F.P.S. Bricks of class designation 75 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 ( 1 cement : 6 coarse sand)

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade Area of slab upto 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge Granite work

Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing ISI marked oxidised M.S. tower bolt black finish (Barrel type) with necessary screws etc. complete : 100x10 mm

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete :125 mm

P/fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners,all necessary fittings complete, including applying a priming coat of approved steel primer. Using flats 30x6mm for diagonal braces and central cross piece Store Door

Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately) Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately)

steel work welded in built up sections/ framed work including cutting, hoisting fixing in position and applying a priming coat of approved steel primer susing structural steel etc. as required. Ventilators

Providing & fixing fly proof wire gauze to windows, clerestory windows &doors with M.S. Flat 15x3 mm and nuts & bolts complete. Galvanised M.S. Wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides

Providing & fixing glass panes with putty and glazing clips in steel doors,windows, clerestory windows, all complete with :5.5 mm thick glass panes FOR WINDOW

Cement concrete flooring 1:2:4 (1 cement : 2coarse sand : 4 gradd stone aggregate) finished with a floating coat of neat cement including cement slurry, (40 mm thick with 20mm nomnal sxe stone aggregate).

P/ fixing glass strips in joints of terrazo/cement concrete floors. (40mm wide and 4mm thick)

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS:15622 (thickness to be specified by the manufacturer), of approved make,in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados,over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), including pointing the joints with white cement and matching pigment etc, complete.

Providing and laying vitrified floor tiles in different sizes(thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar1:4(1cement:4 coarse sand),including grouting the joints with white cement and matching pigments etc.,completeSize of Tile 600x600 mm

Providing and fixing 100mm diameter and 60cm long rain water spolut in cement mortar 1:4 (1cement ;4fine sand).

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. (75mm diameter)

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.( 110mm diameter)

12mm cement plaster of mix: 1:4 (1cement : 4coarse sand)

12mm cement plaster of mix: 1:6 (1cement : 6coarse sand)

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

Distempering with oil bound washable distemper or approved brand and manufacture to give an enen shade . New work (two or more coats ) over and including priming coat with cement primer.

Finishing walls with Acrylic Smooth exterior paint of required shade New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20kg/ 10 sqm)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved prand and manufacture. For Door

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing terminal guard : 75 mm Sand cast iron S&S as per IS - 1729

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 20 mm nominal outer dia Pipes metre

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.External work 15 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.External work 20 mm nominal outer dia Pipes

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making ecessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore 15mm nominal bore

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Engazing suitable carpenter for petty works ( basic rates labour )

Engazing suitable beldar for petty works ( basic rates labour )

Engazing suitable fitter for petty works ( basic rates labour )

Engazing suitable Assistant Fitter or 2nd class Fitter for petty works ( basic rates labour )

Description of Work / Item(s)

Amount

MS Round 32mm dia 6.21 Kg/mtr for earth mat, electodes for earth mat & delta earthing

GI Angle 65x65x6mm

G.I. strip 65x6mm

G.I. strip 50x6mm

GI Channel 125X65x6mm

GI angle 40x40x5mm

Wire mesh fencing with 4mtr and 1mtr wide gate duly painted on both sides.

33 KV,10 KA Lightening Arrester

33 KV 800 A outdoor Type 3P gang operated complete, off load Isolator with earth switch and suitable for D/P structure mounting operated. (i) Incommer

(ii) Outgoing

33 KV Polymer Disc insulator B&S type

Disc fitting B&S 120 KN

Rail 90 Lbs

GI angle 50x50x6 mm for J-hooks

MS Bar, 12 mm Dia for Steel reinforcement

T/F 33/11 KV 12.5 MVA

GI angle 75X75X8 mm 4.5 M long for neutral structure

33 KV Fuse Set

GI bolts & nut with washers.

GI Channel 125x65x6 mm

GI Angle 75x75x8mm

GI Angle 50x50x6 mm

G.I. Plate 300x300x8 mm.

33 KV/110 V O/D type PT

Junction box for 33 KV PT

G.I. Plate 400x400x8 mm.

ST pole SP- 33, 9.0 mtr long (Bottom portion hot dip galvanised)

Earthing rod 20x2500mm

33 KV Aluminium 3Cx50 sq. mm. XLPE

LT XLPE Cable 3.5x70 Sq.mm. for Stn. T/F to ACDB.

ACSR Dog conductor

33/0.433 KV, 63 KVA Station Transformer

G.I. Channel 100x50mm

33 KV off load Vertical type isolator

G.I./MS Bolt & Nut off size

PP clamp with bolts & nuts made by GI

G.I.Strip 35x4mm

Alu lug for T/F HT & LT side.

PG clamp for Panther to Dog Conductor

PG clamp for Bus isolator,Fuse Set suitable for Dog Conductor

Clamp of required size for holding cable supporting channel, pipe, cable etc.

Name plate for station transformer with clamp, nut & bolt

33 KV Danger board with clamp

Stone Pad 300x300x75

GI pipe 4" dia. 3mtr long

Cable jointing kit outdoor type suitable for 3Cx50 sq. mm. XLPE cable 33 KV.

S.T. Pole 11 mtr. Long SP-55 (Bottom Portion hot dip Galvanized)

11 KV Polymer disc insulator B & S

11 KV disc fitting for Rabbit/weasal

11 KV TPMO complete

Stay Set GI 16x1800mm

Stay wire 7/10

GI Wire 6 SWG

9KV 5KA lightening arrestor (Polymer)

11 KV fuse set.

Stay clamp for ST Pole

Clamp of required size for holding cable supporting angle, cable & TPMO handle.

Name plate of feeder

11 KV Danger board with clamp

36 KV, 1250A Gang operated, Permanent Magnetic actuator operated outdoor compact, V.C.B. including in-built epoxy resin cast dry type CT both side bus bar etc. (SCADA OPERATED) (i) Incomer

(ii) Outgoing

Control & Relay Panel with SCADA operated and relay for 33 KV (i) Incomer

(ii) Outgoing

12 KV, 1250A Gang operated, Permanent Magnetic actuator operated outdoor, compact, V.C.B. including in-built epoxy resin cast dry type CT, PT both side bus bar etc. (SCADA OPERATED) (i) 12KV, 1250 A, 26.3KA/3 sec.(BIL 38/95 KV). For Incomer

(ii) 12KV, 1250 A, 26.3KA/3 sec.(BIL 38/95 KV). For outgoing feeder

(iii) 12KV, 1250 A, 26.3KA/3 sec.(BIL 38/95 KV). For capacitor Panel

(iv) 12KV, 1250 A, 26.3KA/3 sec.(BIL 38/95 KV). For Bus coupler

Control & Relay Panel with SCADA operated and relay for 11 KV (i) For Incomer

(ii) For Feeders

(iii) For Capacitor Panel

(iv) For Bus coupler

Cable Aluminium 3Cx400 sq. mm. XLPE 11KV

11 KV 1Cx630 Sq mm AL XLPE cable

Cable jointing kit indoor type suitable for 3Cx400 sq. mm. XLPE cable 11 KV

33 KV alluminium cable 1Cx630 sq mm XLPE

33 KV cable jointing kit 1Cx630 sq mm O/D type

33 KV cable jointing kit 1Cx630 sq mm I/D type

Cable jointing kit outdoor type suitable for 1Cx630 sq. mm. XLPE cable 11 KV

Cable jointing kit indoor type suitable for 1Cx630 sq. mm. XLPE cable 11 KV

HT Cable warning tape

GI pipe 6" dia, 3mtr long

Clamp of MS Flat 50x6 mm. of suitable size for holding 6" & 4" dia. Pipe

PG Clamp for L.A.

10C x 2.5 Sq. mm. LT Control Cable

4C x 2.5 Sq. mm. LT Control Cable

2C x 2.5 Sq. mm. LT Control Cable

MS Angle 50x50x6mm for cable trench

MS Angle 40x40X5mm for cable trench

MS Bar, 10 mm

(i) 400 mm width Perforated tray for cable trench

(ii) 200 mm width Perforated tray for cable trench

(iii) 100 mm width Perforated tray for cable trench

8mtr long ST pole SP-10 (Bottom portion hot dip)

LT PVC cable 4x10 sq. mm.

LT PVC cable 2x6 sq. mm. armed

Iron clad 30 Amps water proof switch on the ST pole.

250W LED lamp with control gear & mounting accessories

DC Distribution box

24 V DC 200 Amp hr Lithium Battery Li,Fe P04 Battery Pack

Float cum boost cum inverter 24 V with Tricle Charging arrengment with all meters AC/DC

Instruction board 3’x2½’ of Flex board duly printed.

Single line diagram of size 3’x2½’ on flex board, duly printed.

Maximum & tripping display board of size 5’x3’ of mica board moulded with frame duly painted & writing.

Sub-station named board (Size 3'x2' of MS sheet & MS angle 45x45x5 mm, Height 1.5 mtr. Above ground level ), duly painted

Name plate of equipment TG, LI, BI, PI, BG, CT, PT, CB, LA etc. (Size 9"x5" with white base, red border & letter written in red color)

Sundries items Cable tie, Alu lug, Copper lug & HT, LT tape, pvc compound, ferrule, pvc flexible pipe, paint writing on panels, HT LT diff size cable gland.

IP CC TV camera 8 nos with monitor (AI based)

Steel office table of size 5'x3' reputated company make

Steel office table of size 4'x2.5' reputated company make

Steel Almirah reputated company make

Steel cabinet reputated company make

Steel office chair reputated company make

1400 mm sweep ceiling fan with Regulator

Padestal fan

Doormat (5'x3')

Dust bin

Shock treatment chart

Danger board

Shut down / Break down board (Bi-lingual Hindi & English)

HT Hand Gloves

Wall Clock

Insulated electrical Plier Taparia

D-Spanner Set Taparia

3 cells Torch

Pipe wrench, 12" Taparia

First aid Box

Earth chain brass 12 mtr. Length

5 KV Megger Digital reputated company make

2.5 KV Megger Digital reputated company make

Earth Megger Digital reputated company make

Rubber mat 1 mtr. wide x 2 mtr long and 12 mm thick to withstand 11 KV dielectric strength as per IS 5424-1969 along the all equipments in Control Room.

Carbon dioxide (CO2) type fire extinguishers conforming to IS 2878 - 1976 and cylinders fully charged of 4.5 Kg capacity.

Foam type fire extinguishers, Portable type 5 lit capacity hanged on wall with bracket complete as required

Metal Fire bucket Filled with sand

Fire bucket stand of Chuggi type of MS angle 50x50x6 mm with top covered by MS sheet 2 mm. thickness and Duly painted with red color including cost of all material, fabrication etc. complete work

9KV, 10KA lightening arrestor

LT Control Cable 6C x 2.5 Sq. mm.

Cable Aluminium 3Cx120 sq. mm. XLPE 11KV

Cable jointing kit outdoor type suitable for 3Cx120 sq. mm. XLPE cable 11 KV

Cable jointing kit indoor type suitable for 3Cx120 sq. mm. XLPE cable 11 KV

12.65KV 4800 KVAr 3 phase 50hz housed in outdoor type IP 5X CRCA Panel Capacitor bank having seven variable step of 150+300+450+600+ 900+1200+1200 KVAr tobe insttaled at substation. Bank shall be complete with capcitor unit of 400/300/200/150/100/50 Kvar, alluminium bus bar, Pin & post insulator, HRC fuses etc outdoor type CRCA panel shall be accomodating capacitors, series reactor, vaccuum contractor, surge succsessor, fuses, RVT etc.

11KV,630Amp off load Isolator with earth switch and mounting structure

Indoor type automatic power factor controller pannel for seven step

Lugs/thimble junction box, 2 nos cable support structure etc.

Cable box of 2mm thick CRCA sheet of dimension 1000x600x500mm (HXWXD) with associated accessories like bus bars,insulators,holding clamp for cable etc.

CT outdoor with mounting structure (1Set=3 Nos)

GI Earthing strip 35x6mm

ACSR Panther conductor

Disc fitting B&S type 90 KN for Panther

PG clamp Panther to Panther

PG clamp Panther to Dog

Wedge connector for panther to panther

Wedge connector for panther to dog

Connectors suitable for Panther for Lightening Arrestor

Connectors suitable for Panther for Isolator

Connectors suitable for Panther for 33 KV VCB

Connectors suitable for Panther for 33 KV PT

Connectors suitable for Panther for T/F HT side

Connectors suitable for Panther for T/F LT side

Flexible copper connection on neutral bushing of power & station transformer 500X50 mm heavy duty with copper lug at ends.

M.S. Angle 65x65x6 for bracing set, 2.7mtr.x2

M.S. Channel 100x50mm for top channel & dropper channel & TPMO handle

M.S. Angle 75x75x8 mm for TPMO & Fuse set (4 nos.x2.24 mtr.)

M.S. Angle 50x50x6 mm for cable support 2.24 mtr.x3No

P.P. & Clamps for S.T. Pole

MS plate 300x300x8 mm

MS Channel 125x65 mm

Construction of 33 KV Line Cable AL 3X400 Sq.mm XLPE 33KV

Cable jointing kit for 33 KV XLPE 3x400 Sqmm Outdoor

MS Channel 100x50mm (3.2X4X10Kg/mtr)

Holding PP Clamp with nut& Bolt

Straight Through Cable jointing kit for 33 KV XLPE 3x400 Sqmm

Description of Work / Item(s)

Amount

Erection of Earth Mat & Earthing work of all equipment and structures of 33/11 KV Sub-Station. (i) Excavation of earth

(ii) Straightening and laying of Earth mat of 32 mm M S round 0.6 mtr or 1 mtr deep in mixed soil according to drawing or as per UPCL direction or/and as per site requirement. Making T-joints, cross joint and Lap joints by welding of M S round bar together using cleats of MS Angles 65x65x6 mm, chipping the slag and painting of the joints with black bitumen paint (including supply of paint) to avoid rusting. Cutting & making electrode 2.5 mtr long with conical pointed bottom and driving of the electrode in ground so that the top of electrode remains 450 mm below ground level. Backfilling of soil in trenches, ramming and leveling of trench properly after completion of eartmat and earthing work is complete. Making of Delta/Bridge earthing for structure/panels i.e. 33 KV LA, 11 KV LA, 33 KV panels, 11 KV panels, ACDB, DCDB, Neutral of power & station transformer.

(iii) Fabrication of GI items

(iv) Earthing of structures using G.I. strips including strengthening, cutting, bending & welding with structure and equipments.

(v) Special earthing by treatment of soil with highly conducted material like combination of bentonite, conductive cement, coke dust, sodium carbonate, MgSo4, NACL & CaCL2 as per ISS 3043-1987.

(vi) Earthfilling in yard

(vii) Supply and spreading of 75mm thick layer of Gravels of size 20mm to 25mm.

Construction of Toe wall and fixing of wire mesh fencing around the switch yard. (i) Excavation of mixed soil

(iii) RR 1:6 below ground level

(iv) CC 1:2:4 on top of RR masonary

(v)Brick work, 1:4

(vi) Cement Plaster 1:4

(vii) Fabrication and Erection of stays post of 40x40x5 mm angle 2.5 mtr long. with required CC 1:4:8 work of size .5x.5x.5

(viii) Fabrication & Erection of RS Joist 175x85x6mm for fixing of wire mesh gate including grouting of the pillar.

(ix)Erection of wiremesh fencing with 4mtr and 1mtr wide gate.

Febrication and erection of 33KV Terminal Gantry. Febrication and erection charges of 33KV Terminal D/P 8.5mtr long of RS joist 150x150mm with double top channel GI 125x65mmx3.2 mtr with bracing set and suitable channel mounted for fixing 33KV Vertical isolator and Lightening arrestor including supply of all materials.

Febrication and erection of 33KV Bus Gantry. Febrication and erection charges of 33KV Bus D/P 8.5mtr long of RS joist 150x150mm with double top channel GI 125x65mmx3.2 mtr with bracing set and suitable channel mounted including supply of all materials.

Construction of Power Transformer Plinth. (i) Fabrication of Rail 90 Lbs,cutting of GI angle 50x50x6 mm and MS Bar 12 mm.

(ii) Excavation of earth in mixed soil

(iii) CC 1:4:8

(iv) Brick work in 1:4

(vi) Plaster in 1:4

Erection and Fixing of Power Transformer on Plinth. (i) Shifting of transformer from road side to transformer plinth through chain pully, lift pully and slippers etc.

(ii) Erection of transformer by fixing all accessories, tank, filling of transformer oil etc.

(iii) Fabrication & erection of neutral structure including excavation & grouting in CC 1:4:8

Erection and fixing of 33 KV Fuse Set. (i) Fabrication charges of structure as per approved drawing

(ii) Excavation of earth in mixed soil

(iii) Grouting of structure with C.C. in 1:3:6 ratio

(iv) Cement Plaster 1:4, on top & side walls

(v) Erection charges of structure

(vi) Fixing and erection charges of Fuse set

Erection and Fixing of 33 KV Lightening Arrestor. (i) Fabrication charges of structure as per approved drawing

(ii) Excavation of earth in mixed soil

(iii) Grouting of structure with C.C. in 1:3:6 ratio

(iv) Cement Plaster 1:4, on top & side walls

(v) Erection charges of structure

(vi) Fixing and erection charges of Lightening arrestor

Erection and Fixing of 33 KV Potential Transformer. (i) Fabrication charges of MS item

(ii) Erection charges of structure

(iii) Fixing and erection of equipments.

Erection and Fixing of 33/0.433KV,63 KVA Station Transformer. (i) Excavation of earth

(ii) Cement concreting of Double pole 1:4:8

(iii) Cement Plaster in 1:4

(iv) Fabrication charges of channels

(v) Erection of Double pole complete with all fittings, channels etc. complete work

(vi) Labour charge for pit digging 0.6mtr below GL for earthing rod making delta for T/F neutral and then welding with GI strip and taking out 1 for T/F Neutral ,1 for T/F Body and 1 for L.A. including cost of welding and N&B.

(vii) Painting of structure with one coat of red oxide paint and two coat of Aluminium paint of best quality I.S.I. mark Dulux, Burger, Asian make including cost of red oxide, paint.

(viii) Erection of 33/0.433 KV station transformer on double pole with all accessories complete work

(ix) Laying, spreading & jointing of LT cable by using propers ties, lugs, connectors, cable glands in cable trench and equipments..

(x) Digging open trench 120cm deep and 45cm wide and prepare 10 cm thick fine sand cushion and then Laying of 33KV 3X400Sqmm cable over this cushion,then covered the cable with another 10cm thick sand layer.The trench is then covered with brick and other material covering all around cable protected on sides and top as per site requirement.

(xi) Filling/Fixing of cable jointing kit 33 KV indoor and outdoor type

(xii) Erection of vertical 33 KV isolator on double pole SP-33 complete by assembeling, fixing of operating handle, pipe, clamps, pins etc for smooth operation of the isolator.

Erection and Fixing of Double Pole Structure of outgoing 11KV Feeder. (i) Excavation of earth

(ii) Cement concreting of Double pole 1:4:8

(iii) Cement Plaster in 1:4

(iv) Fabrication charges of channels & angle

(v) Erection of Double pole complete with all fittings, accessories, stays & earthing.

(vi) Painting of structure with one coat of red oxide paint and two coat of Aluminium paint of best quality I.S.I. mark Dulux, Burger, Asian make including cost of red oxide, paint.

Erection and Fixing of 33 KV Circuit Breaker and C&R Panel. (i) Cartage of all panels from road side to SGR

(ii) Placing of panels on specific place over SGR trench on MS Channels and fixing of pannels with nut & bolts.

(iii) Making electrical connection of panels by control wiring complete with & VCB etc.

Erection and Fixing of 11 KV Circuit Breaker and C&R Panel. (i) Cartage of all panels from road side to SGR

(ii) Placing of panels on specific place over SGR trench on MS Channels and fixing of pannels with nut & bolts.

(iii) Making electrical connection of panels by control wiring complete with & VCB etc.

Laying of 33KV/11KV XLPE Cable. (i) Laying of 33 KV/ 11 KV Cable by excavation of cable trench in mixed soil, filling of the sand upto the height 250mm from the bottom most level of the cable trench thereafter properly laying of the cable by placing bricks on both side of the cable than re-filling of the sand from the top so as to cover the cable completely and then placing the bricks on the top of the covered cable, spreading of cable warning tape & covering of the trench completly with mixed soil including cost of sand, bricks, etc.

(ii) Filling of cable jointing kit 33 KV indoor & outdoor type

(iii) Filling of cable jointing kit 11 KV indoor & outdoor type

(iv) Fabrication charges of MS items

(v) Fixing of GI Pipes

(vi) Erection of cable supporting MS Channel & angle

Construction of cable trench and laying of LT control cable. (i) Fabrication charges of MS item

(ii) Making cable trench including fabrication, fixing of MS angle 50x50x6 mm size (excluding the cost of MS Angle/ MS bar) on side edge with all excavation, CC work, brick work, fixing of cable support angle one/two tier as required with stopper arrangement at 0.5 mtr gap throughout the length of the trench, making of cable trench covers with MS Bar welded mesh angle frame of MS angle 40x40x6 mm. with lifting hooks, fixing of perforated tray complete as per drawing including cost of sand, cement, bricks, metal (gitti) etc.

(iii) Laying, spreading & jointing of LT control cable by using propers ties,lugs, connectors, cable glands in cable trench and equipments..

Fixing and Erection of Lights at Yard and S.G.Room. (i) Excavation of earth

(ii) Cement concreting in 1:4:8 ratio

(iii) Erection of ST Pole SP-10 and fitting of accessories.

(iv) Painting of ST Pole with one coat of red oxide primer and two coat of Aluminium paint.

(v) Erection of 250 watt lighting equipment & all its accessories

(vi) Laying of LT PVC cable 4x10 sq. mm. in soil & back filling of sand.

Fixing, placing and erection of Misc Items. (i) Erection of 24 V Battery Set

(ii) Erection of Battery Charger

(iii) Erection of DCDB

(iv) Erection of ACDB

(v) Erection of Name plates, instruction board, SLD, Max., Min. board etc.

(vi) Erection of substation name board by grouting in CC 1:4:8 ratio

(vii) Erection & fixing of CCTV camera including required material for complete work

Fixing, placing and erection of T&P and furniture material

Instalation/Mounting of Fire Extinguishers

Erection and Fixing of 11KV Capacitor Bank. Civil work (including foundation,plinth of capacitor cubical etc as per RESPO Drawing) (i) Earth work

(ii) Brick work 1:6 Sub Structure

(iii) Brick work 1:6 Super Structure

(iv) Cement plaster 1:6 (12mm thick) on plinth

(vii) CC 1:1.5:2

(viii) Steel Reinforcement

(ix) Fixing and erection of capacitor bank with complete accessories.

(x) Fixing and erection of 11KV,630Amp off load Isolator with earth switch and mounting structure

(xi) Filling of cable jointing kit 11 KV indoor & outdoor type

(xii) Cable trench in size 30x20cm for laying of power/control cable including cost of all material.

(xiii) Laying of power and control cable in trench including all connections.

(xiv) Supply & fixing of electrode chemical earthing and GI strip 50x6 mm for equpments

Erection and Fixing of Bua Bar & Connectors. (i) Fixing of Flexible copper connection on neutral bushing of power & station transformer .

(ii) Labour charges for drawing bus-bar & making connection in each equipment, main & auxilary bus bar.

Shifting of Existing Transformer on newly constructed plinth including dismentalling and all necessary work/items to energization of T/F complete work.

Testing of S/s

33 KV Line Erection Work (i) Fabrication Charges of MS items

(ii) Digging open trench 120cm deep and 45cm wide and prepare 10 cm thick fine sand cushion and then Laying of 33KV 3X400Sqmm cable over this cushion,then covered the cable with another 10cm thick sand layer.The trench is then covered with brick and other material covering all around cable protected on sides and top as per site requirement.

(iii) Laying of cable for loop etc.

(iv) Supply and fixing of GI Pipe (with Socket) 4or 5 inch dia at points of road crossing, cable rising etc ( B Class)

(v) Fixing of 33 KV 3core XLPE Outdoor cable jointining kit of 400 Sqmm

(vi) Fixing of MS Channel,Holding clamp for cable support.

(vii) Making pit of size 5X2X2 mtr for filling and fixing of 33KV Straight through joint kit with back filling,ramming and compaction upto complete restoration.

Description of Work / Item(s)

Amount

Annual Maintenance Charges (AMC) of Project for 5 years on per year basis.

Description of Work / Item(s)

Amount

Construction of Boundary wall Earth work in excavation by mechanical means (Hydraulic excavator ) manual means in foundation tranches (not exceeding 1.5m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50m. (All kinds of soil). For wall

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering -All work up to plinth level:1:4 :8 (1 Cement :4 coarse sand: 8 graded stone aggregate 40 mm nominal size)

Brick work with F.P.S. bricks of class designation 75 in foundation and plinth in: Cement mortar 1:6 ( 1 cement : 6 coarse sand)

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement- All work up to plinth level: 1:2:4 (1 cement : 1.5 coarse sand: 3 graded stone aggregate 20 cm nominal size).

Reinforced cement concrete working beams, suspended floors, roofs having slope up to 1.5 landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral/ stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement with 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting propping etc. and removal of form for: Lintels, beams, plinth beams girders, bressumers and cantilevers,

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. (Cold twisted bars ).

Brick work with F.P.S. Bricks of class designation 75 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 ( 1 cement : 6 coarse sand)

Steel work welded in built up sections/ framed work including cutting, hoisting fixing in position and applying a priming coat of approved steel primer susing structural steel etc. as required. (In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.)

12mm cement plaster of mix: 1:6 (1cement :6coarse sand) In wall

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved prand and manufacture.

Filling available excavated earth (excluding rock) in trenches, plinth sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5m

Construction of SGR Building Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50m. All kinds of soil.

Supplying and filling in plinth with Jamuna sand under floors, including watering, ramming, consolidating and dressing complete.

Supplying and stacking at site.Good earth

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :sand: 3 graded stone aggregate 20 cm nominal size).1:1.5:3 (1 cement : 1.5coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting propping etc. and removal of form for: Foundations footings, bases of columns, etc. For mass concrete.

Centering and shuttering including strutting propping etc. and removal of form for: Suspended floors, roofs, landings, balconies and access platform.

Centering and shuttering including strutting propping etc. and removal of form for: Shelves (Cast in situ)

Centering and shuttering including strutting propping etc. and removal of form for: Lintels, beams, plinth beams girders, bressumers and cantilevers,

Centering and shuttering including strutting propping etc. and removal of form for:. Columns, Pillars, Piers, Abutments, Posts and Struts.

Centering and shuttering including strutting propping etc. and removal of form for. Weather shade, Chaffas, corbels etc. including edges.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:4 (1 cement :4 coarse sand)

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade Area of slab upto 0.50 sqm

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite of any colour and shade Area of slab over 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge Granite work

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.35 mm thick including ISI marked Stainless Steel butt hinges with necessary screwsmatched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hingeswith necessary screws

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete :250x16 mm

Providing and fixing ISI marked oxidised M.S. tower bolt black finish (Barrel type) with necessary screws etc. complete : 200x10 mm

Providing and fixing ISI marked oxidised M.S. tower bolt black finish (Barrel type) with necessary screws etc. complete : 150x10 mm

Providing and fixing ISI marked oxidised M.S. tower bolt black finish (Barrel type) with necessary screws etc. complete : 100x10 mm

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete :125 mm

Providing and fixing aluminium sliding door bolts, ISI marked anodised anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 250x16 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :(200x10mm)

Providing and fixing aluminium tower door bolts ISI marked anodised (Anodic coating not less than grade AC 10 as per IS:1868)transparent or dyed to required colour or shade with nuts and screws etc. complete: (150x10mm)

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :100x10 mm

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :125mm

Providing and fixing aluminium handles floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary scerews etc. complet: Single rubber stopper

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Twin rubber stopper

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.With stainless steel cover plate minimum 1.25 mm thickness

Providing and fixing wire gauge shutters using stainless steel grade 304 wire gauge with wire of dia 0.5 mm and average width of aperture 1.4 mm in both directions for doors, windows and clerestory windows with necessary screws : 35 mm thick shutters with ISI marked M.S. pressed butt hinges bright finished of required size Second class teak wood

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer.

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strikeplate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineerin-charge:Profile B Fixing with adjustable lugs with split end tail to each jamb

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strikeplate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineerin-charge:Profile C Fixing with adjustable lugs with split end tail to each jamb

Steel work in built up tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard rawing.surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete. Galvanised M.S. Wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with :5.5 mm thick glass panes

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate20mm nomnal sxe stone aggregate).

Providing and fixing glass strips in joints of terrazo/ cement concrete floors. 40 mm wide and 4 mm thick

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados,over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 oarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigments etc., complet

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 600x600 mm

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600x600 mm

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. (75mm diameter)

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.( 110mm diameter)

Providing and fixing precoated galvanised iron profile sheets (size,shape and pitch of corrugation as approved by Engineer-in-charge)0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer?in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. for Old SGR

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade , 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Ridges plain (500 - 600mm)

12mm cement plaster of mix: 1:4 (1cement : 4coarse sand)

12mm cement plaster of mix: 1:6 (1cement :6coarse sand)

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water tinnable priming coat with cement primer.

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/ 10 sqm

Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Providing and laying 60mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing terminal guard : 75 mm Sand cast iron S&S as per IS - 1729

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 100 mm inlet and 100 mm outlet Sand cast iron S&S as per IS: 3989

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall : 15 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 15 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 20mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 25 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 40 mm dia nominal bore

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making ecessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.(15 mm nominal bore)

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore 15mm nominal bore

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

P/Fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side

Engazing suitable carpenter for petty works (basic rates labour )

Engazing suitable beldar for petty works ( basic rates labour ) for replacing old s tin shed

Engazing suitable fitter for electrical works ( basic rates labour )

Construction of SGR Building (ELECTRICAL ITEMS) Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required. GROUP B

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required. GROUP C

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required2*2.5 Sq.M*1*2.5Sq.M

Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including nnections but excluding modular plate etc. as required.

Supply and Installation 1.00HP water pump Havells and equivalent make all compl.as per direction of E.I.

Supply of 1200 mm sweep ceiling fan of approved quality ( Bajaj,USHA, Havells or equilent make) without regulator.

Supplying of Exaust Fan 450 mm sweep of orient or equivalent make as apporoved by E.I

(1.41) Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

(1.50.1)Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required Upto 450 mm sweep

Supply and Installation 1.00HP water pump Havells and equivalent make all compl.as per direction of E.I.

Supply of 20 watt LED Tubelight Philips or equivalent make approved by E.I.

Supplying of Exaust Fan 450 mm sweep of orient or equivalent make as apporoved by E.I

(1.41) Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

(1.50.1)Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required Upto 450 mm sweep

Supply ,Installation,Testing and Commissioning 1200 mm sweep, BEE 5 star rated,ceiling fan with brush less direct current (BLDC)Motor,class of insulation:B, 3 no. blades, 30 cm long down rod ,2 nos canopies,shakle kit,safety rope,copper winding ,power factor not less then 0.9,service value(cmm/w)minimum 6.85,aire delivery minnimum 215 cmm, 350 rpm(tollerance as per IS : 374/219),THD less then 10%,remote of electronic regulator unit 4 speed controll and all remaining accesories including safety pin ,nut bolts,washers,temperature rise equal to75 degree c (max), insulation resistance more then 2 mega ohm ,suitable for 230 v ,50 Hz ,single phase AC supply , earthing etc complete as required.

Description of Work / Item(s)

Amount

MS Round 32mm dia 6.21 Kg/mtr for earth mat, electodes for earth mat & delta earthing

GI Angle 65x65x6mm

G.I. strip 65x6mm

G.I. strip 50x6mm

GI Channel 125X65x6mm

GI angle 40x40x5mm

Wire mesh fencing with 4mtr and 1mtr wide gate duly painted on both sides.

33 KV,10 KA Lightening Arrester

33 KV 800 A outdoor Type 3P gang operated complete, off load Isolator with earth switch and suitable for D/P structure mounting operated. (i) Incommer

(ii) Outgoing

33 KV Polymer Disc insulator B&S type

Disc fitting B&S 120 KN

Rail 90 Lbs

GI angle 50x50x6 mm for J-hooks

MS Bar, 12 mm Dia for Steel reinforcement

T/F 33/11 KV 12.5 MVA

GI angle 75X75X8 mm 4.5 M long for neutral structure

33 KV Fuse Set

GI bolts & nut with washers.

GI Angle 75x75x8mm

GI Angle 50x50x6 mm

33 KV/110 V O/D type PT

Junction box for 33 KV PT

G.I. Plate 400x400x8 mm.

ST pole SP- 33, 9.0 mtr long (Bottom portion hot dip galvanised)

Earthing rod 20x2500mm

33 KV Aluminium 3Cx50 sq. mm. XLPE

LT XLPE Cable 3.5x70 Sq.mm. for Stn. T/F to ACDB.

ACSR Dog conductor

33/0.433 KV, 63 KVA Station Transformer

G.I. Channel 100x50mm

33 KV off load Vertical type isolator

G.I. /MS Bolt & Nut off size

PP clamp with bolts & nuts made by GI

G.I.Strip 35x4mm

Alu lug for T/F HT & LT side.

PG clamp for Panther to Dog Conductor

PG clamp for Bus isolator,Fuse Set suitable for Dog Conductor

Clamp of required size for holding cable supporting channel, pipe, cable etc.

Name plate for station transformer with clamp, nut & bolt

33 KV Danger board with clamp

Stone Pad 300x300x75

GI pipe 4" dia. 3mtr long

Cable jointing kit outdoor type suitable for 3Cx50 sq. mm. XLPE cable 33 KV.

S.T. Pole 11 mtr. Long SP-55 (Bottom Portion hot dip Galvanized)

11 KV Polymer disc insulator B & S

11 KV disc fitting for Rabbit/weasal

11 KV TPMO complete

Stay Set GI 16x1800mm

Stay wire 7/10

GI Wire 6 SWG

9KV 5KA lightening arrestor (Polymer)

11 KV fuse set.

Stay clamp for ST Pole

Clamp of required size for holding cable supporting angle, cable & TPMO handle

Name plate of feeder

11 KV Danger board with clamp

36 KV, 1250A Gang operated, Permanent Magnetic actuator operated outdoor compact, V.C.B. including in-built epoxy resin cast dry type CT both side bus bar etc. (SCADA OPERATED) (i) Incomer

(ii) Outgoing

Control & Relay Panel with SCADA operated and relay for 33 KV (i) Incomer

(ii) Outgoing

12 KV, 1250A Gang operated, Permanent Magnetic actuator operated outdoor, compact, V.C.B. including in-built epoxy resin cast dry type CT, PT both side bus bar etc. (SCADA OPERATED) (i) 12KV, 1250 A, 26.3KA/3 sec.(BIL 38/95 KV). For Incomer

12KV, 1250 A, 26.3KA/3 sec.(BIL 38/95 KV). For outgoing feeder

12KV, 1250 A, 26.3KA/3 sec.(BIL 38/95 KV). For capacitor Panel

12KV, 1250 A, 26.3KA/3 sec.(BIL 38/95 KV). For Bus coupler

Control & Relay Panel with SCADA operated and relay for 11 KV (i) For Incomer

(ii) For Feeders

(iii) For Capacitor Panel

(iv) For Bus coupler

Cable Aluminium 3Cx400 sq. mm. XLPE 11KV

11 KV 1Cx630 Sq mm AL XLPE cable

Cable jointing kit indoor type suitable for 3Cx400 sq. mm. XLPE cable 11 KV

33 KV alluminium cable 1Cx630 sq mm XLPE

33 KV cable jointing kit 1Cx630 sq mm O/D type

33 KV cable jointing kit 1Cx630 sq mm I/D type

Cable jointing kit outdoor type suitable for 1Cx630 sq. mm. XLPE cable 11 KV

Cable jointing kit indoor type suitable for 1Cx630 sq. mm. XLPE cable 11 KV

HT Cable warning tape

GI pipe 6" dia, 3mtr long

Clamp of MS Flat 50x6 mm. of suitable size for holding 6" & 4" dia. Pipe

PG Clamp for L.A.

10C x 2.5 Sq. mm. LT Control Cable

4C x 2.5 Sq. mm. LT Control Cable

2C x 2.5 Sq. mm. LT Control Cable

MS Angle 50x50x6mm for cable trench

MS Angle 40x40X5mm for cable trench

MS Bar, 10 mm

(i) 400 mm width Perforated tray for cable trench

(ii) 200 mm width Perforated tray for cable trench

(iii) 100 mm width Perforated tray for cable trench

8mtr long ST pole SP-10 (Bottom portion hot dip)

LT PVC cable 4x10 sq. mm.

LT PVC cable 2x6 sq. mm. armed

Iron clad 30 Amps water proof switch on the ST pole.

250W LED lamp with control gear & mounting accessories

DC Distribution box

24 V DC 200 Amp hr Lithium Battery Li,Fe P04 Battery Pack

Float cum boost cum inverter 24 V with Tricle Charging arrengment with all meters AC/DC

Instruction board 3’x2½’ of Flex board duly printed.

Single line diagram of size 3’x2½’ on flex board, duly printed.

Maximum & tripping display board of size 5’x3’ of mica board moulded with frame duly painted & writing.

Sub-station named board (Size 3'x2' of MS sheet & MS angle 45x45x5 mm, Height 1.5 mtr. Above ground level ), duly painted

Name plate of equipment TG, LI, BI, PI, BG, CT, PT, CB, LA etc. (Size 9"x5" with white base, red border & letter written in red color)

Sundries items Cable tie, Alu lug, Copper lug & HT, LT tape, pvc compound, ferrule, pvc flexible pipe, paint writing on panels, HT LT diff size cable gland.

IP CC TV camera 8 nos with monitor (AI based)

Steel office table of size 5'x3' reputated company make

Steel office table of size 4'x2.5' reputated company make

Steel Almirah reputated company make

Steel cabinet reputated company make

Steel office chair reputated company make

1400 mm sweep ceiling fan with Regulator

Padestal fan

Doormat (5'x3')

Dust bin

Shock treatment chart

Danger board

Shut down / Break down board (Bi-lingual Hindi & English)

HT Hand Gloves

Wall Clock

Insulated electrical Plier Taparia

D-Spanner Set Taparia

3 cells Torch

Pipe wrench, 12" Taparia

First aid Box

Earth chain brass 12 mtr. Length

5 KV Megger Digital reputated company make

2.5 KV Megger Digital reputated company make

Earth Megger Digital reputated company make

Rubber mat 1 mtr. wide x 2 mtr long and 12 mm thick to withstand 11 KV dielectric strength as per IS 5424-1969 along the all equipments in Control Room.

Carbon dioxide (CO2) type fire extinguishers conforming to IS 2878 - 1976 and cylinders fully charged of 4.5 Kg capacity.

Foam type fire extinguishers, Portable type 5 lit capacity hanged on wall with bracket complete as required

Metal Fire bucket Filled with sand

Fire bucket stand of Chuggi type of MS angle 50x50x6 mm with top covered by MS sheet 2 mm. thickness and Duly painted with red color including cost of all material, fabrication etc. complete work.

9KV, 10KA lightening arrestor

LT Control Cable 6C x 2.5 Sq. mm.

Cable Aluminium 3Cx120 sq. mm. XLPE 11KV

Cable jointing kit outdoor type suitable for 3Cx120 sq. mm. XLPE cable 11 KV

Cable jointing kit indoor type suitable for 3Cx120 sq. mm. XLPE cable 11 KV

12.65KV 4800 KVAr 3 phase 50hz housed in outdoor type IP 5X CRCA Panel Capacitor bank having seven variable step of 150+300+450+600+ 900+1200+1200 KVAr tobe insttaled at substation. Bank shall be complete with capcitor unit of 400/300/200/150/100/50 Kvar, alluminium bus bar, Pin & post insulator, HRC fuses etc outdoor type CRCA panel shall be accomodating capacitors, series reactor, vaccuum contractor, surge succsessor, fuses, RVT etc.

11KV,630Amp off load Isolator with earth switch and mounting structure

Indoor type automatic power factor controller pannel for seven step

Lugs/thimble junction box, 2 nos cable support structure etc.

Cable box of 2mm thick CRCA sheet of dimension 1000x600x500mm (HXWXD) with associated accessories like bus bars,insulators,holding clamp for cable etc.

CT outdoor with mounting structure (1Set=3 Nos)

GI Earthing strip 35x6mm

ACSR Panther conductor

Disc fitting B&S type 90 KN for Panther

PG clamp Panther to Panther

PG clamp Panther to Dog

Wedge connector for panther to panther

Wedge connector for panther to dog

Connectors suitable for Panther for Lightening Arrestor

Connectors suitable for Panther for Isolator

Connectors suitable for Panther for 33 KV VCB

Connectors suitable for Panther for 33 KV PT

Connectors suitable for Panther for T/F HT side

Connectors suitable for Panther for T/F LT side

Connectors suitable for Panther for Flexible copper connection on neutral bushing of power & station transformer 500X50 mm heavy duty with copper lug at ends.

M.S. Angle 65x65x6 for bracing set, 2.7mtr.x2

M.S. Channel 100x50mm for top channel & dropper channel & TPMO handle

M.S. Angle 75x75x8 mm for TPMO & Fuse set (4 nos.x2.24 mtr.)

M.S. Angle 50x50x6 mm for cable support 2.24 mtr.x3No

MS Channel 125x65 mm

MS plate 300x300x8 mm

G.I. plate 300x300x8 mm

PP & clamps for ST Poles

Description of Work / Item(s)

Amount

Erection Work Erection of Earth Mat & Earthing work of all equipment and structures of 33/11 KV Sub-Station. (i) Excavation of earth

(ii) Straightening and laying of Earth mat of 32 mm M S round 0.6 mtr or 1 mtr deep in mixed soil according to drawing or as per UPCL direction or/and as per site requirement. Making T-joints, cross joint and Lap joints by welding of M S round bar together using cleats of MS Angles 65x65x6 mm, chipping the slag and painting of the joints with black bitumen paint (including supply of paint) to avoid rusting. Cutting & making electrode 2.5 mtr long with conical pointed bottom and driving of the electrode in ground so that the top of electrode remains 450 mm below ground level. Backfilling of soil in trenches, ramming and leveling of trench properly after completion of eartmat and earthing work is complete. Making of Delta/Bridge earthing for structure/panels i.e. 33 KV LA, 11 KV LA, 33 KV panels, 11 KV panels, ACDB, DCDB, Neutral of power & station transformer.

(iii) Fabrication of GI items

(iv) Earthing of structures using G.I. strips including strengthening, cutting, bending & welding with structure and equipments.

(v) Special earthing by treatment of soil with highly conducted material like combination of bentonite, conductive cement, coke dust, sodium carbonate, MgSo4, NACL & CaCL2 as per ISS 3043-1987.

(vi) Earthfilling in yard

(vii) Supply and spreading of 75mm thick layer of Gravels of size 20mm to 25mm.

Construction of Toe wall and fixing of wire mesh fencing around the switch yard. (i) Excavation of mixed soil

(iii) RR 1:6 below ground level

(iv) CC 1:2:4 on top of RR masonary

(v) Brick work, 1:4

(vi) Cement Plaster 1:4

(vii) Fabrication and Erection of stays post of 40x40x5 mm angle 2.5 mtr long. with required CC 1:4:8 work of size .5x.5x.5

(viii) Fabrication & Erection of RS Joist 175x85x6mm for fixing of wire mesh gate including grouting of the pillar.

(ix) Erection of wiremesh fencing with 4mtr and 1mtr wide gate.

Fabrication and erection of 33KV Terminal Gantry. Fabrication and erection charges of 33KV Terminal D/P 8.5mtr long of RS joist 150x150mm with double top channel GI 125x65mmx3.2 mtr with bracing set and suitable channel mounted for fixing 33KV Vertical isolator and Lightening arrestor including supply of all materials.

Fabrication and erection of 33KV Bus Gantry. Fabrication and erection charges of 33KV Bus D/P 8.5mtr long of RS joist 150x150mm with double top channel GI 125x65mmx3.2 mtr with bracing set and suitable channel mounted including supply of all materials.

Construction of Power Transformer Plinth. (i) Fabrication of Rail 90 Lbs, cutting of GI angle 50x50x6 mm and MS Bar 12 mm

(ii) Excavation of earth in mixed soil

(iii) CC 1:4:8

(iv) Brick work in 1:4

(vi) Plaster in 1:4

Erection and Fixing of Power Transformer on Plinth. (i) Shifting of transformer from road side to transformer plinth through chain pully, lift pully and slippers etc

(ii) Erection of transformer by fixing all accessories, tank, filling of transformer oil etc.

(iii) Fabrication & erection of neutral structure including excavation & grouting in CC 1:4:8

Erection and fixing of 33 KV Fuse Set. (i) Fabrication charges of structure as per approved drawing

(ii) Excavation of earth in mixed soil

(iii) Grouting of structure with C.C. in 1:3:6 ratio

(iv) Cement Plaster 1:4, on top & side walls

(v) Erection charges of structure

(vi) Fixing and erection charges of Fuse set

Erection and Fixing of 33 KV Lightening Arrestor. (i) Fabrication charges of structure as per approved drawing

(ii) Excavation of earth in mixed soil

(iii) Grouting of structure with C.C. in 1:3:6 ratio

(iv) Cement Plaster 1:4, on top & side walls

(v) Erection charges of structure

(vi)Fixing and erection charges of Lightening arrestor

Erection and Fixing of 33 KV Potential Transformer. (i) Fabrication charges of MS item

(ii) Erection charges of structure

(iii) Fixing and erection of equipments.

Erection and Fixing of 33/0.433KV,63 KVA Station Transformer. (i) Excavation of earth

(ii) Cement concreting of Double pole 1:4:8

(iii) Cement Plaster in 1:4

(iv)Fabrication charges of channels

(v) Erection of Double pole complete with all fittings, channels etc. complete work.

(vi) Labour charge for pit digging 0.6mtr below GL for earthing rod making delta for T/F neutral and then welding with GI strip and taking out 1 for T/F Neutral ,1 for T/F Body and 1 for L.A. including cost of welding and N&B.

(vii) Painting of structure with one coat of red oxide paint and two coat of Aluminium paint of best quality I.S.I. mark Dulux, Burger, Asian make including cost of red oxide, paint.

(viii) Erection of 33/0.433 KV station transformer on double pole with all accessories complete work

(ix) Laying, spreading & jointing of LT cable by using propers ties, lugs, connectors, cable glands in cable trench and equipments..

(x) Digging open trench 120cm deep and 45cm wide and prepare 10 cm thick fine sand cushion and then Laying of 33KV 3X400Sqmm cable over this cushion,then covered the cable with another 10cm thick sand layer.The trench is then covered with brick and other material covering all around cable protected on sides and top as per site requirement.

(xi) Filling/Fixing of cable jointing kit 33 KV indoor and outdoor type

(xii) Erection of vertical 33 KV isolator on double pole SP-33 complete by assembeling, fixing of operating handle, pipe, clamps, pins etc for smooth operation of the isolator.

Erection and Fixing of Double Pole Structure of outgoing 11KV Feeder. (i) Excavation of earth

(ii) Cement concreting of Double pole 1:4:8

(iii) Cement Plaster in 1:4

(iv) Fabrication charges of channels & angle

(v) Erection of Double pole complete with all fittings, accessories, stays & earthing.

(vi) Painting of structure with one coat of red oxide paint and two coat of Aluminium paint of best quality I.S.I. mark Dulux, Burger, Asian make including cost of red oxide, paint.

Erection and Fixing of 33 KV Circuit Breaker and C&R Panel. (i) Cartage of all panels from road side to SGR

(ii) Placing of panels on specific place over SGR trench on MS Channels and fixing of pannels with nut & bolts.

(iii) Making electrical connection of panels by control wiring complete with & VCB etc.

Erection and Fixing of 11 KV Circuit Breaker and C&R Panel. (i) Cartage of all panels from road side to SGR

(ii) Placing of panels on specific place over SGR trench on MS Channels and fixing of pannels with nut & bolts.

(iii) Making electrical connection of panels by control wiring complete with & VCB etc.

Laying of 33KV/11KV XLPE Cable. (i) Laying of 33 KV/ 11 KV Cable by excavation of cable trench in mixed soil, filling of the sand upto the height 250mm from the bottom most level of the cable trench thereafter properly laying of the cable by placing bricks on both side of the cable than re-filling of the sand from the top so as to cover the cable completely and then placing the bricks on the top of the covered cable, spreading of cable warning tape & covering of the trench completly with mixed soil including cost of sand, bricks, etc.

(ii) Filling of cable jointing kit 33 KV indoor & outdoor type

(iii) Filling of cable jointing kit 11 KV indoor & outdoor type

(iv) Fabrication charges of MS items

(v) Fixing of GI Pipes

(vi) Erection of cable supporting MS Channel & angle

Construction of cable trench and laying of LT control cable. (i) Fabrication charges of MS item

(ii) Making cable trench including fabrication, fixing of MS angle 50x50x6 mm size (excluding the cost of MS Angle/ MS bar) on side edge with all excavation, CC work, brick work, fixing of cable support angle one/two tier as required with stopper arrangement at 0.5 mtr gap throughout the length of the trench, making of cable trench covers with MS Bar welded mesh angle frame of MS angle 40x40x6 mm. with lifting hooks, fixing of perforated tray complete as per drawing including cost of sand, cement, bricks, metal (gitti) etc.

(iii) Laying, spreading & jointing of LT control cable by using propers ties,lugs, connectors, cable glands in cable trench and equipments..

Fixing and Erection of Lights at Yard and S.G.Room. (i) Excavation of earth

(ii) Cement concreting in 1:4:8 ratio

(iii) Erection of ST Pole SP-10 and fitting of accessories.

(iv) Painting of ST Pole with one coat of red oxide primer and two coat of Aluminium paint.

(v) Erection of 250 watt lighting equipment & all its accessories

(vi) Laying of LT PVC cable 4x10 sq. mm. in soil & back filling of sand.

Fixing, placing and erection of Misc Items. (i) Erection of 24 V Battery Set

(ii) Erection of Battery Charger

(iii) Erection of DCDB

(iv) Erection of ACDB

(v) Erection of Name plates, instruction board, SLD, Max., Min. board etc.

(vi) Erection of substation name board by grouting in CC 1:4:8 ratio

(vii) Erection & fixing of CCTV camera including required material for complete work

Fixing, placing and erection of T&P and furniture material

Instalation/Mounting of Fire Extinguishers

Erection and Fixing of 11KV Capacitor Bank. Civil work (including foundation,plinth of capacitor cubical etc as per RESPO Drawing) (i) Earth work

(ii) Brick work 1:6 Sub Structure

(iii) Brick work 1:6 Super Structure

(iv) Cement plaster 1:6 (12mm thick) on plinth

(vii) CC 1:1.5:2

(viii) Steel Reinforcement

(ix) Fixing and erection of capacitor bank with complete accessories.

(x) Fixing and erection of 11KV,630Amp off load Isolator with earth switch and mounting structure

(xi) Filling of cable jointing kit 11 KV indoor & outdoor type

(xii) Cable trench in size 30x20cm for laying of power/control cable including cost of all material.

(xiii) Laying of power and control cable in trench including all connections.

(xiv) Supply & fixing of electrode chemical earthing and GI strip 50x6 mm for equpments

Erection and Fixing of Bua Bar & Connectors. (i) Fixing of Flexible copper connection on neutral bushing of power & station transformer .

(ii) Labour charges for drawing bus-bar & making connection in each equipment, main & auxilary bus bar.

Testing of S/s

Description of Work / Item(s)

Amount

Annual Maintenance Charges (AMC) of Project for 5 years on per year basis.

Description of Work / Item(s)

Amount

Construction of S G R Building Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50m. All kinds of soil.

Supplying and filling in plinth with Jamuna sand under floors, including watering, ramming, consolidating and dressing complete.

Supplying and stacking at site.Good earth

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :sand: 3 graded stone aggregate 20 cm nominal size).1:1.5:3 (1 cement : 1.5coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting propping etc. and removal of form for: Foundations footings, bases of columns, etc. For mass concrete.

Centering and shuttering including strutting propping etc. and removal of form for: Suspended floors, roofs, landings, balconies and access platform.

Centering and shuttering including strutting propping etc. and removal of form for: Shelves (Cast in situ)

Centering and shuttering including strutting propping etc. and removal of form for: Lintels, beams, plinth beams girders, bressumers and cantilevers,

Centering and shuttering including strutting propping etc. and removal of form for:. Columns, Pillars, Piers, Abutments, Posts and Struts.

Centering and shuttering including strutting propping etc. and removal of form for. Weather shade, Chaffas, corbels etc. including edges.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:4 (1 cement :4 coarse sand)

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade Area of slab upto 0.50 sqm

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite of any colour and shade Area of slab over 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge Granite work

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.35 mm thick including ISI marked Stainless Steel butt hinges with necessary screwsmatched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hingeswith necessary screws

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete :250x16 mm

Providing and fixing ISI marked oxidised M.S. tower bolt black finish (Barrel type) with necessary screws etc. complete : 200x10 mm

Providing and fixing ISI marked oxidised M.S. tower bolt black finish (Barrel type) with necessary screws etc. complete : 150x10 mm

Providing and fixing ISI marked oxidised M.S. tower bolt black finish (Barrel type) with necessary screws etc. complete : 100x10 mm

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete :125 mm

Providing and fixing aluminium sliding door bolts, ISI marked anodised anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 250x16 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :(200x10mm)

Providing and fixing aluminium tower door bolts ISI marked anodised (Anodic coating not less than grade AC 10 as per IS:1868)transparent or dyed to required colour or shade with nuts and screws etc. complete: (150x10mm)

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :100x10 mm

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :125mm

Providing and fixing aluminium handles floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary scerews etc. complet: Single rubber stopper

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Twin rubber stopper

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.With stainless steel cover plate minimum 1.25 mm thickness

Providing and fixing wire gauge shutters using stainless steel grade 304 wire gauge with wire of dia 0.5 mm and average width of aperture 1.4 mm in both directions for doors, windows and clerestory windows with necessary screws : 35 mm thick shutters with ISI marked M.S. pressed butt hinges bright finished of required size Second class teak wood

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer.

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strikeplate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineerin-charge:Profile B Fixing with adjustable lugs with split end tail to each jamb

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strikeplate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineerin-charge:Profile C Fixing with adjustable lugs with split end tail to each jamb

Steel work in built up tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard rawing.surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete. Galvanised M.S. Wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with :5.5 mm thick glass panes

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate20mm nomnal sxe stone aggregate).

Providing and fixing glass strips in joints of terrazo/ cement concrete floors. 40 mm wide and 4 mm thick

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados,over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 oarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigments etc., complet

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 600x600 mm

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600x600 mm

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. (75mm diameter)

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.( 110mm diameter)

Providing and fixing precoated galvanised iron profile sheets (size,shape and pitch of corrugation as approved by Engineer-in-charge)0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer?in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. for Old SGR

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade , 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Ridges plain (500 - 600mm)

12mm cement plaster of mix: 1:4 (1cement : 4coarse sand)

12mm cement plaster of mix: 1:6 (1cement :6coarse sand)

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water tinnable priming coat with cement primer.

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/ 10 sqm

Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Providing and laying 60mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing terminal guard : 75 mm Sand cast iron S&S as per IS - 1729

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 100 mm inlet and 100 mm outlet Sand cast iron S&S as per IS: 3989

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall : 15 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 15 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 20mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 25 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 40 mm dia nominal bore

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making ecessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.(15 mm nominal bore)

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore 15mm nominal bore

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

P/Fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side

Engazing suitable carpenter for petty works (basic rates labour )

Engazing suitable beldar for petty works ( basic rates labour ) for replacing old s tin shed

Engazing suitable fitter for electrical works ( basic rates labour )

Construction of SGR Building (ELECTRICAL ITEMS) Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required. GROUP B

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required. GROUP C

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required2*2.5 Sq.M*1*2.5Sq.M

Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including nnections but excluding modular plate etc. as required.

Supply and Installation 1.00HP water pump Havells and equivalent make all compl.as per direction of E.I.

Supply of 1200 mm sweep ceiling fan of approved quality ( Bajaj,USHA, Havells or equilent make) without regulator.

Supplying of Exaust Fan 450 mm sweep of orient or equivalent make as apporoved by E.I

(1.41) Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

(1.50.1)Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required Upto 450 mm sweep

Supply and Installation 1.00HP water pump Havells and equivalent make all compl.as per direction of E.I.

Supply of 20 watt LED Tubelight Philips or equivalent make approved by E.I.

Supplying of Exaust Fan 450 mm sweep of orient or equivalent make as apporoved by E.I

(1.41) Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

(1.50.1)Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required Upto 450 mm sweep

Supply ,Installation,Testing and Commissioning 1200 mm sweep, BEE 5 star rated,ceiling fan with brush less direct current (BLDC)Motor,class of insulation:B, 3 no. blades, 30 cm long down rod ,2 nos canopies,shakle kit,safety rope,copper winding ,power factor not less then 0.9,service value(cmm/w)minimum 6.85,aire delivery minnimum 215 cmm, 350 rpm(tollerance as per IS : 374/219),THD less then 10%,remote of electronic regulator unit 4 speed controll and all remaining accesories including safety pin ,nut bolts,washers,temperature rise equal to75 degree c (max), insulation resistance more then 2 mega ohm ,suitable for 230 v ,50 Hz ,single phase AC supply , earthing etc complete as required.

Construction of Revenue Collection Room, Toilet Earth work in excavation by mechanical means (Hydraulic excavator ) manual means in foundation tranches (not exceeding 1.5m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5m, (All kinds of soil). Columns Footing F1

Filling available excavated earth (excluding rock) in trenches, plinth sides of foundations etc. in layers not exceeding 20 cm in depth,

Supplying and filling in plinth with Jamuna sand under floors including. Watering, ramming consolidating and dressing complete. .

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering -All work up to plinth level:1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering -All work up to plinth level:1:4 :8 (1 Cement :4 coarse sand: 8 graded stone aggregate 40 mm nominal size)

Providing and laying damp-proof course 40 cm thick with cement concrete 1:2:4 ( 1 cement :2 coarse sand: 4 graded stone aggregate 12.5 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement .All work up to plinth level: 1:1:5:3 (1 cement : 1.5 coarse sand: 3 graded stone aggregate 20 cm nominal size).

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, posts reinforcement. 1:1:5:3 (1 cement : 2 coarse sand 4 graded stone aggregate 20 cm nominal size). Columns

Reinforced cement concrete working beams, suspended floors, roofs having slope up to 1.5 landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral/ of centering, shuttering, finishing and reinforcement with 1:1.5:3

Centering and shuttering including strutting propping etc. and removal of form for: Foundations footings, bases of columns, etc. For mass concrete. Cols Footings

Centering and shuttering including strutting propping etc. and removal of form for: Suspended floors, roofs, landings, balconies and access platform.

Centering and shuttering including strutting propping etc. and removal of form for: Shelves (Cast in situ)Sheleves bottom

Centering and shuttering incl. strutting propping etc. and removal of form for: Lintels, beams, plinth beams and cantilevers,

Centering and shuttering including strutting propping etc. and removal of form for:. Columns, Pillars, Piers, Abutments, Posts and Struts. Columns

Centering and shuttering including strutting propping etc. and removal of form for. Weather shade, Chaffas, corbels etc. including edges.

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. (Cold twisted bars ).

Brick work with F.P.S. bricks of class designation 75 in foundation and plinth in: Cement mortar 1:4( 1 cement : 4 coarse sand)

Brick work with F.P.S. bricks of class designation 75 in foundation and plinth in: Cement mortar 1:6 ( 1 cement : 6 coarse sand)

Brick work with F.P.S. Bricks of class designation 75 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 ( 1 cement : 6 coarse sand)

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade Area of slab upto 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge Granite work

Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing ISI marked oxidised M.S. tower bolt black finish (Barrel type) with necessary screws etc. complete : 100x10 mm

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete :125 mm

Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately) Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately)

steel work welded in built up sections/ framed work including cutting, hoisting fixing in position and applying a priming coat of approved steel primer susing structural steel etc. as required. Ventilators

Providing & fixing fly proof wire gauze to windows, clerestory windows &doors with M.S. Flat 15x3 mm and nuts & bolts complete. Galvanised M.S. Wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides

Providing & fixing glass panes with putty and glazing clips in steel doors,windows, clerestory windows, all complete with :5.5 mm thick glass panes FOR WINDOW

Cement concrete flooring 1:2:4 (1 cement : 2coarse sand : 4 gradd stone aggregate) finished with a floating coat of neat cement including cement slurry, (40 mm thick with 20mm nomnal sxe stone aggregate).

P/ fixing glass strips in joints of terrazo/cement concrete floors. (40mm wide and 4mm thick)

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS:15622 (thickness to be specified by the manufacturer), of approved make,in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados,over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), including pointing the joints with white cement and matching pigment etc, complete.

Providing and laying vitrified floor tiles in different sizes(thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar1:4(1cement:4 coarse sand),including grouting the joints with white cement and matching pigments etc.,completeSize of Tile 600x600 mm

Providing and fixing 100mm diameter and 60cm long rain water spolut in cement mortar 1:4 (1cement ;4fine sand).

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. (75mm diameter)

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.( 110mm diameter)

12mm cement plaster of mix: 1:4 (1cement : 4coarse sand)

12mm cement plaster of mix: 1:6 (1cement :6coarse sand)

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

Distempering with oil bound washable distemper or approved brand and manufacture to give an enen shade . New work (two or more coats ) over and including priming coat with cement primer.

Finishing walls with Acrylic Smooth exterior paint of required shade New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20kg/ 10 sqm)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved prand and manufacture. For Door

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing terminal guard : 75 mm Sand cast iron S&S as per IS - 1729

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 20 mm nominal outer dia Pipes metre

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.External work 15 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.External work 20 mm nominal outer dia Pipes

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making ecessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore 15mm nominal bore

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Engazing suitable carpenter for petty works ( basic rates labour )

Engazing suitable beldar for petty works ( basic rates labour )

Engazing suitable fitter for petty works ( basic rates labour )

Engazing suitable Assistant Fitter or 2nd class Fitter for petty works ( basic rates labour )

Land Development Works (Construction of C.C road ) Earth work in excavation by mechanical means (Hydraulic excavator ) manual means in foundation tranches (not exceeding 1.5m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50m. (All kinds of soil) For Toe Wall

Supplying and filling in plinth with Jamuna sand under floors, including watering, ramming, consolidating and dressing complete. Filling for site

Supplying and stacking at site.Good earth

P/laying in position cement concrete of specified grade excluding the cost of centering and shuttering -All work up to plinth level:1:4 :8 (1 Cement :4 coarse sand: 8 graded stone aggregate 40 mm nominal size)In

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:4 (1 cement :4 coarse sand)

Cement concrete pavement with 1:2:4 including finishing complete. Road c.c.

steel work in builtup sections/framed work in frames,guard bars,railings,gates,similar work.railings

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes (110mm diameter)

12mm cement plaster of mix: 1:6 (1cement :6coarse sand)

Stone Aggregate (Single size) : 20 mm nominal size In Yard

Ganpati Infrapower Private Limited (BID ID -355629)

Ganpati Infrapower Private Limited (BID ID -355629)

Ganpati Infrapower Private Limited (BID ID -355629)

Ganpati Infrapower Private Limited (BID ID -355629)

Ganpati Infrapower Private Limited (BID ID -355629)

Ganpati Infrapower Private Limited (BID ID -355629)

Ganpati Infrapower Private Limited (BID ID -355629)

Ganpati Infrapower Private Limited (BID ID -355629)

Ganpati Infrapower Private Limited (BID ID -355629)

Ganpati Infrapower Private Limited (BID ID -355629)

Ganpati Infrapower Private Limited (BID ID -355629)

Ganpati Infrapower Private Limited (BID ID -355629)

Ganpati Infrapower Private Limited (BID ID -355629)