IMPROVEMENT UPGRADATION OF CERTAIN LIVING IN ACCN AND MESSES AT AFS WADSAR

Amount

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) n.exc 1.5 sqm each

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) exc 1.5 sqm but n.exc 4.00 sqm each

Taking down shutters of any description exc 1 sqm and n.exc 2 sqm each

Taking down shutters of any description exc 2 sqm and n.exc 4 sqm each

Taking down and refixing shutters of any description exc 1 sqm and n. exc 2 sqm each in the same opening after, easing and adjusting including refixing builders hardware as per requirement with new screws complete.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as sepcified and as directed

Dismantling wrought iron or mild steel work of any description not otherwise provided

Demolition of cement concrete (reinforced) of any description in any position not otherwise specially provided for complete all as specified

Demolition of cement concrete(unreinforced) in ground floors and paving n.exc 15 cm thickness (below or above G.L) and rubbish off the premise complete all as specified and directed

Dismantling of un-reinforcement lime concrete/cement concrete in padding to roof slab and removing the rubbish off premises out side MD land all as directed.

Demolition of Brickwork or stone/boulder masonry, built in CM or cement lime mortar including all quoins, arches, pillars etc, but excluding ashlar facings, dressed stonework & precast concrete articles complete all as specified

Complete removal of existing unserviceable water proofing treatment including PCC tiles (except PCC padding) but including cement plaster etc, of any description and cleaning of top surface of cement concrete flushing out junction of parapet walls & washing down with water to remove all dirt etc including preparation of surfaces to receive new treatment and removing the rubbish off premises out side MD land.

Dismantling stone slabs and tiles of any description or thickness in floors, aprons etc. laid and bedded on pointed on any mortar complete all as specified and directed.

Dismantling of floor hearth or wall tilling including cement mortar bedding (but not backing) removing serviceable tiles and rubbish off the premise complete all as specified and directed

Taking down cement or cement lime plaster any description on brick or stone wall/ celling including raking out joint , hacking for key scrubbing with water etc complete all as specified and directed

Taking up or down 15mm bore steel tubing and connection including cleaning for refixing or removal to store all as directed.

Taking up or down 20mm bore steel tubing and connection including cleaning for refixing or removal to store all as directed.

Dismantling PVC water tanks of capacity exc. 250 but n. exc. 500 litre capacity complete all as specified and as directed.

Dismantling PVC water tanks of capacity exc. 500 but n. exc. 1000 litre capacity complete all as specified and as directed.

Taking down PVC pipe (SWR) 110mm dia bore from wall or floor complete all as specified

M&L PCC 1:2:4 Type B-0, using 12.50mm graded aggregate laid to slope in padding for WPT over roof slab complete all as specified

M&L RCC 1:1½:3 (Nominal mix ) Type A1 using 20mm graded stone aggregate as in column ,beam ,posts and pillars etc complete all as specified and as directed..

M& LPrecast cement concrete 1:2:4 type B-0 (using 12.5mm and below stone aggregate ) in kerb stone factory made as approved by GE with plain fair faces including champhering, weathering etc complete with joint to match in CM 1:6 complete all as specified

Supply only liquid water proofing compound

M&L Brick work with sub class B bricks, straight or curved on plan to any radius built in half brick thick walls in CM 1:4 all as specified.

M&L Brick work sub class B bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed.

M&L Use and waste of formwork to sides of pillars, posts, struts, piers, columns,beams and stanchions rough finished surfaces of concrete circular on plan complete all as specified and as directed.

S&F Solid PVC door frame of size 50mm x 47mm made out of 5mm prelam colour PVC sheet reinforced with MS square tube complete all as specified

S&F Factory made solid PVC moulded door shutter, 28 to 30 mm thick (stiles), with 2,4 or 6 raised panel designed with 2 mm thick moulded PVC sheet on front face and 4mm plain colour PVC sheet on back face as per specification complete all as specified

S & F Factory made solid panel PVC door shutter 30 mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement all as shown in SSR Part – II 2020 complete all as specified

S&F Factory made powder coated uPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, as per approved drawing l complete all as specified (Note: The unit rate quoted by contractor includes cost of glass and all other connected accessories complete

S&F Factory made powder coated uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two Nos. glazed & one No. wire mesh panels) upto 1.50m height made of (big series) frame 108 x 60 mm & sash 46 x 60 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. comprising of uPVC multi chambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge (Note: The quoted rate deem inclusive of glazing, SS wire mesh and all other accessories complete)

M&L 35 mm thick 2nd class hardwood glazed and skeleton shutter open rebated and prepared to receive glass gauze etc (with sash bar) edges of framing plain chamfered or rounded filled with cut and mitered beads for securing, glass etc size of member of shutter as per specified in SSR Part-I complete all as specified

M&L 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, kiln seasoned and chemically pressed treated complete all as specified

M&L Aluminium powder coated (powder coated of required colour) three track sliding windows frame top & sides of size 92x31.75x1.50 mm, bottom size 92x31.75x1.50 mm and shutter top & bottom of size 40x18x1.50 mm and sides (handle) of size 40x18x1.50 mm and lock side shutter frame of size 40x18x1.50 mm with rubber gasket, beading and locking arrangement including making good to the disturbed portion complete including stainless steel wire mesh 0.36mm nominal dia of wire with 1.40mm average aperture and fixed with stainless steel wire staples and fixing 4 mm thick glass with necessary rubber beading gasket etc, one wire mesh shutter and two Nos glass shutter as per drawing No CEAA/STD/01/2010 sheet No 1/1 complete all as specified and directed

S&F Aluminium ventilator powder coated (required colour to match window colour), louvers type, frame top & bottom of size 31x42x1.50 mm (rectangular tub of size 40x20x2mm (and middle vertical of size 42x46.20x1.50 mm section and clip for fixing wire mesh and glass of size 19x17.30x0.90 mm thick including provision of one guaged shutter with stainless steel wire cloth 0.36mm nominal dia of wire and 1.40 mm average width of aperture and fixed with stainless steel wire staples and 4 mm thick glass louvers with blades of 100mm with heavy duty rubber beading, gasket etc complete all as specified

M&L Aluminium powder coated (required colour to match window colour) grill of 5 mm thick DG-102 as per Drawing No CEAA/TD-144 sheet No 1/1 fixed with H or F channel of décor or equivalent complete all as specified

M&L Aluminium doors, powder coated (of approved colour), with frame of section 100mm x 44mm x 1.50 mm thick and shutter with bottom rail of section 150mm x 44.5mm x 1.50 mm thick, middle rail of section 85mm x 44.5mm x 1.50 mm thick and top rail of section 80.4mm x 44.5mm x 1.50 mm thick and styles of section 80.4mm x 44.5mm x 1.50 mm thick with 4 mm thick glass (plain/ tinted/ with laminated film) or pre laminated board fixed in position with aluminium beading including necessary rubber gaskets and 2 Nos. aluminium push plate handle of aluminium section 150 mm wide and 1.50 mm thick including 150 mm aluminium tower bolt, brass mortice lock complete all as per Drawing No. CEAA/TD/63 sheet No. 2.2 complete all as specified and as directed.

M&L Aluminium partition made with aluminium anodised section 62.30 x 44.45 x 1.50 mm fixed in wall including provision for receiving glass pane etc and fixing the same with aluminium anodised beading and rubber gasket including 5mm thick glass (black/tinted/plain) and all necessary fittings as in partition complete all as specified and as directed.

S&F 125mm long heavy weight cold rolled mild steel hinges to frame with screwed or welding complete all as specified and directed.

S&F 100mm long medium weight cold rolled mild steel hinges to frame with screwed or welding complete all as specified and directed.

S&F 100 mm long SS butt hinges and fixed to frame with screwed or welding complete all as specified..

S&F 150mm long aluminium anodized barrel tower bolts of extruded section and fixed complete all as specified...

S&F Aluminium alloy anodized sliding door bolt with haps and staple (bolt type) and fixing clip of sheet cast or extruded section or cast aluminium alloy and fixed length of bolt 250 mm complete all as specified

S&F 150mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified..

S&F 150mm long floor door stopper of aluminium body and tongue, with hard drawn steel spring, fixed to bottom of door shutter complete all as specified..

S&F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete as in repairs all as specified

S&F CP peg set of four fixed to wooden boards/ door shutters complete all as specified

S&F 25 mm dia stainless steel drapery rod with and including two Nos of bracket/holders suitable for drapery 25 mm dia rods of one window / door openings complete all as specified

S&F Roller window blinds, roller shade look and classy , covering the window edge to edge for windows, roll up blinds come with the rolling machanism, colours, design, and patterns as approved complete as in repairs all as specified

S&F Framed work as in door frames or gates chowkats of angle or other section with braces, etc., complete, drilled or welded for MS hinges for fixing of gate or doors other covering and also fastening and fixing complete as in repairs all as specified

M&L Mild steel TMT bars 10mm dia and over cut to length bent to shape required including cranking bending spirally for hooping for columns hooking ends and binding with and including mild steel wire(annealed ) not less than 0.9mm dia or securing with clips complete all as specified

M&L Mild steel TMT bars 5mm dia & over upto & including 10mm dia in stirrups, spacers & binders, cut to length, bent to shape required, binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality complete all as specified

S&F MS framed works as in purlin, rafters, column square / rectangular, round or angle section, fixed with and including iron cleats or other connected plates flat iron wind ties etc including bending of MS section as required such as grills, gratings, etc. with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

S&F MS angle posts & struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., & similar work conforming to Fe 290-0 Gde E-165 complete all as specified

S&F Galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings & straining & fixing to any type of standard rails straining bolts, including, securing or tying at crossings with & provision of galvanised mild steel wire, staples or steel pins, etc. complete as in repairs all as specified and directed

S&F MS galvanised punched type concertina coil 1050mm dia when stretched with 80 Nos of clip with weight 15.6Kg/coil and average coverage area is 6.00RM per coil complete all as specified

S& F Mild steel screw bolt (machine made) with hexagonal or square heads at one end and screwed the other each screwed end to be fitted with washers and one hexagonal nut but length bolt one side embedded in concrete posts etc complete to fix fencing wire dia of shank 11 to 15mm,but length of bolt exc 10cm and n exc 15cm long complete all as spcified

M&L Pre- painted. Galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering fixed with self tapping screws complete all as specified

M&L Pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified

M&L Rendering 10mm thick in CM 1:4, mixed with liquid WPC @200 milli litre per bag of cement on fair faces of concrete surfaces without using extra cement as in roof complete all as specified and directed. Note:- WPC shall be measured & paid separately..

S&F Welded steel wire fabric fixed to steel members of weight not exceeding 4 kg per sqm complete all as specified

S&F Suspended ceiling of plaster of paris of approved pattern and design 12.5 mm thick which include GI perimeter channel of size 20 x 27 x 30 x 0.5 mm thick along perimeter of ceiling screwed/fixed to brick wall or existing supports at 610 mm centre to centre suspending GI intermediate channel of size 15 x.15 x 0.9mm thick from the slit at 610 mm centre with ceiling angle (GI) of size 25 x 10 x 0.55mm thick fixed to the solid with GI cleat 0.5 mm thick having knotted web of 51.5mm and two flanges of size 26mm each with lips of 10.50 mm fixed to the intermediated channel with the help of connecting clip and in the direction perpendicular to the intermediate channel at 300 mm centres, POP ceiling boards of size 1220mm width x 12.5 mm thick screwed to ceiling section with 25 mm long screw @ 230mm centres, screw fixed mechanically either with screw driver or drilling machine with suitable attachment. Ceiling shall be sealed at joints and finished with jointing compound etc complete including finishing the exposed surfaces of false ceiling with two coats of plastic emulsion paint over a coat of primer complete all as specified and directed

S&F Solid PVC Wall Lining consisting of 5mm thick coloured PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per pattern decided by Engr-in-Charge including providing grooves between panels if any as complete all as specified and directed.

S&F 5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on to wall to make PVC Frame as per specification complete all as specified

S&F Aluminium Composite panel of Viva/ alucobond of any colours) 3mm thick exterior grade PVDF with foil thick of 0.25mm & frame work made out from aluminium section of size 38x25mm supported on masonry/RCC with the help of MS Bracket fixed with brick fastener/ Anchor fastener and groove filled with 789 weather silent of DOW corning etc. complete all as specified

M&L False ceiling at height of 600 x 600 x 12 mm mineral fibre ceiling tiles RH-99 of type micro looks edge laid on super fine XL 15mm exposed grid systems with 15mm wide T- section flanges. The frame work comprises of main runner of size 15x32x3000 mm spaced at 1200 mm centre securing fixed to the structural soffits by approved hangers at 1200mm maximum centers. Hangers (GI wire of 3.0mm dia) to be fixed by approved roof plug, level adjusters and screws etc. The last hanger at the end of each main runner should not be greater than 450mm from the adjacent wall flush fitting 1200mm long cross tees of size 15x26x1200 mm to be interlocked between main runners at 600mm centers to form a 1200mm x 600 mm module. Cut cross tees longer than that 600mm to be supported independently. 600 mm x 600 mm modules to be formed by fitting 600mm long flush fitting cross tees of size 15x26x600 mm centrally between the 1200mm cross tees perimeter wall angle of size 19x19x3000 mm secured to wall at 450mm maximum centres. Finally, RH-99 mineral fibre tile 15mm thick micro look edge has to be laid on the 600mm x 600mm module complete all as specified and directed.

M&L Preparing clean and dried plastered surface and applying a coat of oil based bitumen primer conforming to IS 3384-1986 @ 0.30 litrs/sqm and laying APP polymer modified membrane 3.5mm thick with non-woven polyester reinforced membrane (min 3.50 kg/sqm) having thermal insulation with white mineral gravel finish on upper side of membrane and laid by torch application method to the entire surface all as specified and directed

M&L 25 mm thick PCC 1:2:4 type B0 using12.5mm graded aggregate as in levelling course complete all as specified and directed.

M&L 75 mm thick PCC 1:4:8 type D-2 using 40mm graded aggregate as in sub base complete all as specified

M&L Rubber moulded Machine pressed precast concrete interlocking paver block any shape and size with grey cement and pigment confirming to IS 15658-2006 of 80 mm thickness M-40 Grade over25mm thick sand cushion complete all as specified

M&L Granite work (of any type) 20 mm thick (table rubbed and polished) in steps, risers, door jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 10mm thick CM 1:4 complete all as specified

Rounding/ moulding to edges of stone slabs one/ all edge, such as in steps, cooking platform, and other similar situations all as specified and directed.

M&L Vitrified ceramic tiles 10mm thick dark shade (square / rectangular) polished area of each tiles exceeding 0.36Sqm but not exceeding 0.42 Sqm, in floor/skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over screed bed with 15mm thick in CM 1:4 complete all as specified complete all as specified and as directed.

M&L Vitrified ceramic (dark shade /double charged / ultra charged tiles 10 mm thick (square/rectangular) polished, area of each tiles exc 0.42 sqm and n exc 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, over screed bed with 15mm thick in CM 1:4 complete all as specified

M&L Non- skid ceramic coloured joint free tiles 7 to 8mm thick (square/ Rectangular) area of each tiles exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over screed bed with 15mm thick in CM 1:4 complete all as specified.

M&L Glazed ceramic coloured digital tiles 450x300mm x 7mm thick in vertical surface etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick backing coat in CM 1:4 complete all as specified.

M&L 20 - 25mm thick machine cut kota stone slab as in flooring laid over 15mm thick cement mortar 1:6 screed base laid pointed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified.

Grinding and Mirror finish polishing to existing Kota stone flooring / skirting in any position complete all as specified

Taking down cement plaster and decayed concrete of any description, upto double storey building from roof projection, chajjas etc and making good the decayed portion with cement mortar 1:3 mixed with integral water proofing compound or PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate including necessary form work, GI wire netting of 0.90mm dia & 12mm mesh size and scaffolding where ever required, rendering with 15 mm thick cement mortar 1:3, surface finished even and smooth without using extra cement using integral water proofing compound as per manufacturers instructions , complete all as specified & directed. Note : Integral water proofing compound shall be measured & paid separately.

M&L 15mm thick rendering on fair faces of concrete or brick masonry surfaces in CM 1:6 finished even and smooth without using extra cement complete all as specified and directed

M&L 15mm thick rendering in two layers on concrete or brick masonry surfaces, ,first layer with 10 mm thick in CM 1:6 and second layer with 5 mm thick in CM 1:4 finished even and smooth without using extra cement in wall complete all as specified and directed

M&L 5 mm thick rendering on ceiling surfaces.in CM 1:3 finished even and smooth without using extra cement complete all as specified and directed

M&L Preparation of new plastered surface of wall and applying two coats of distemper oil emulsion over a coat of primer and 3mm thick coat of wall care putty complete all as specified .

M&L Complete removal of existing treatment of ceiling surface and applying two coats of oil emulsion distemper over a coat of primer and 3mm thick coat of wall care putty complete all as specified .

M&L Preparation of new wall surfaces and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over priming coat of exterior wall primer @ 0.90 litre/ 10 sqm complete all as specified and directed.

M&L Complete removal of existing treatment of wall surface and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and directed.

M&L Complete removal of existing treatment from wall or ceiling surface by washing , rubbing down, stopping of distempered and painted surface including preparing surfaces by applying 3mm thick white wall care putty and texture painting of desired pattern or design and shade as per manufacturer’s instructions complete all as specified

S&F 12 mm thick toughened glass as in doors, partitions including hinges, door closer/automatic door closer/floor spring and similar work including cutting to shape, moulding of edge etching design if required including locking device and SS handles drilling holes required and necessary fitting for fixing the same complete all as specified and as directed.

M&L Preparation of old wooden painted surfaces of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint complete all as specified..

M&L Preparation of new steel surface of any description over 10cm width or girth not otherwise described and applying and two coats of synthetic enamel paint over a coat of zinc chromate primer complete all as specified.

S&F 16mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls / ceiling including all PP-R plain & brass threaded polypropylene random fittings as required complete all as specified.

S&F 20mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls / ceiling complete all as specified. including all PP-R plain & brass threaded polypropylene random fittings complete all as specified.

Dismantling of existing water tank up to and including 1000Ltr capacity over the roof and re-fixing in the same position including cleaning complete all as specified

S&F Rotational moulded water storage tank 500 ltr capacity double layer (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified.

S&F Rotational moulded water storage tank 750 ltr capacity double layer (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified

S&F Rotational moulded water storage tank 1000 ltr capacity double layer (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified

S&F 15mm ball brass valves, high pressure, with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed complete as in repairs all as specified and as directed.

S&F 15mm dia brass CP fancy type single lever tall body Basin Mixer with quarter / half turn type screwed down high pressure, with or without lettered hot and screwed shanks and fly nuts, screwed for iron pipes or for WHB complete as in repairs all as specified

S&F Brass chromium plated towel ring including brackets/flanges complete as in repairs all as specified

S&F 15 mm dia CP bib taps, fancy typecast copper alloy with half turn type capstan heads, screwed down screwed for iron pipe or for brass ferrule and fixed. complete as in repairs all as specified and directed .

S&F 15mm dia CP stop / angular cock fancy type cast copper alloy,screwed down high pressure with half turn type capstan heads, screwed both end for iron pipe or for unions and fixed complete as in repairs all as specified and directed.

S&F 15mm dia 2 wayangular cock fancy type cast copper alloy,screwed down high pressure with half turn type capstan heads, screwed both end for iron pipe or for unions and fixed complete as in repairs all as specified and directed.

S&F 15mm bore two way angle valve cock chromium plated fancy type, screwed down screwed for iron pipe or for brass ferrule and fixed complete as in repairs all as specified and directed .

S&F 15mm dia CP stop valve fancy type cast copper alloy, with long shank and cup (concealed type) screwed down high pressure with half turn type capstan heads, screwed both end for iron pipe or for unions and fixed complete as in repairs all as specified and directed

S&F 15 mm dia pillar taps fancy type of chromium Plated brass with half turn type capstan heads screwed down high pressure, with or without lettered hot and cold with long shank, screwed shanks and fly nuts, screwed complete as in repairs all as specified and directed.

S&F 15 mm dia one hole WHB mixer swivel spout deck mounted including necessary fittings and waste system fancy type of chromium plated brass with half turn type capstan heads screwed down high pressure, with or without lettered hot and cold with long shank, screwed shanks and fly nuts, screwed complete as in repairs all as specified

S&F Fancy type, CP hand shower rose complete as in repair all as specified and directed

S&F Fancy type, CP hand shower with 1.5 Mtr CP hose and hook complete as in repair all as specified and directed

S&F Basin of size 600 x 400 x140 mm with waste coupling complete all as specified and directed.

S&F Single piece EWC of size 680-x3600x750 mm with PP soft close seat cover and fixed with 'S' or 'P' strap including all necessary fittings like jet and flexible pipe etc complete as in repairs all as specified

S&F 125 mm dia Fancy type CP shower rose complete as in repairs all as specified and directed.

S&F SS soap dish of size 100mm complete as in repairs all as specified and directed

S&F SS soap dish with tumbler holder complete as in repairs all as specified and directed

S&F Vitreous china wash basin with pedestal flat back size 550X400 mm white, excluding taps, waste ,chain and plug and chain porcelain stopper but including brackets cutting for and pinning in ends of brackets or erecting stand complete as in repairs all as specified and directed..

S&F Vitreous china wash down water closet pan semi pedestal pattern ,white excluding fixing cistern and flush pipe trap front or back inlet including seat cover of any pattern and health faucet (ABS) with rubit cleaning system 1.25 m long, PVC flexible tube and ABS wall hook complete as in repairs all as specified

S&F Brass chromium plated tubular towel rail 20 mm dia 'D' type 60 cm long including brackets/flanges complete as in repairs all as specified

S&F PVC water connection 600 mm long to wash basin of 15mm dia including CP nuts and washers complete all as specified

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete as in repairs all as specified and directed

S&F Glass corner shelf 12 x 12 inch wall mount with 5mm thickness with SS railing all as specified and as directed

S&F 75 mm dia bore pipe (SWR) single socket in any length rubber joints fixed to wall.or floor or complete all specified

S&F 110 mm dia bore pipe (SWR) single socket in any length rubber joints fixed to wall or floor or trenches complete all as specified.

S&F 110mm bore PVC (SWR) bends any radius with access door complete all as specified.

S&F 110mm bore PVC (SWR) junction single, (single T) equal or unequal any radius with access door complete all as specified.

S&F 110mm bore PVC (SWR) junction double, (Double T) equal or unequal any radius with access door complete all as specified.

S&F 110mm bore PVC (SWR) cowl any radius complete all as specified.

S&F 75mm bore PVC (SWR) bends any radius with access doo complete all as specified .

S&F 75mm bore PVC (SWR) junction single, (single T) equal or unequal any radius with access door complete all as specified.

S&F 75mm bore PVC (SWR) junction double, (double T) equal or unequal any radius with access door complete all as specified.

S&F 110mm bore PVC (SWR) junction double+B175, (Double T) equal or unequal any radius with access door complete all as specified.

S&F 75 mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified.

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified.

Taking down carefully old unserviceable copper/ aluminium point wiring (Light, fan, socket, power and Bell) including fixture and fittings such as switches, sockets, ceiling roses, lamp, holder , regulators, sockets light fittings etc , removing material to store for keeping in safe custody or for taking credit , and making good disturbed surface of walls, floors, etc. complete all as specified

M & L Concealed point wiring in replacement complete with FRLSH PVC insulated /unsheathed stranded copper conductor of wire 1.5 Sqmm , 1100 volt grade , along with one single core of same size stranded copper as continuous earth wire to common earth dolly in and including PVC conduit pipe fitting medium grade of 25 mm dia fixed in concealed surface of wall/ceiling/false ceiling including cutting /chasing in wall as required with ISI mark heavy duty PVC flux boxes suitable for modular plate of required sizes and thickness (factory made) sunk in wall where as required and accessories complete all as specified for the following :-

(a) One light/bell/fan point controlled by one switch complete

(b) One 3 Pin socket out let 5 Amps on the same board.

(c) One 3 pin socket out let 5 Amps on the independent board.

(d) One bell point controlled by one bell push

Ditto- all as per item No.138 above but with cable of size 2.5 Sq mm PVC insulated on independent board for power plug/sockets 15 Amps complete all as specified and directed by Engr in Charge.

S&F Modular switch one way 6A,1 Module, complete all as specified and directed

S&F Modular socket 6/10A-2/3 pin combined 2 Module complete all as specified and directed

S&F Modular switch one way 16A,1 Module, complete all as specified and directed

S&F Modular socket 16A-2/3 pin combined 2 Module complete all as specified and directed

S&F Modular bell push 6A,1 Module complete all as specified and directed

S&F Modular fan step regulator 120W, 1 module complete all as specified and directed

S & F Door bell ding dong AC 230volts complete all as specified and as directed.

S & F White cover plate with frame , 1 module complete all as specified and directed

S & F White cover plate with frame , 2 module complete all as specified and directed

S & F White cover plate with frame , 4 module complete all as specified and directed

S & F White cover plate with frame , 8 module complete all as specified and directed

S& F Ceiling rose with cover plate , 5 Amps surface type 240 volts bakelite three terminal complete all as specified and directed

S&F Ding dong bell AC 230V complete all as specified and directed

S&F Sheet metal enclosure, single phase, double door DB,240 Volts flush to wall mounting for MCB fitted with 200 Amp rated bus bars and neutral links (without MCB's) 8 ways SPN complete as in repairs all as specified and directed

S&F Sheet metal enclosure, single phase, double door DB,415 Volts flush to wall mounting for MCB fitted with 200 Amp rated bus bars and neutral links (without MCB's) 4 ways TPN complete as in repairs all as specified and directed

S& MCB, SP 240 volts capacity 5 - 32 Amps current rating, 10KA breaking capacity complete as in repairs all as specified and directed

S&F MCB, SPN 240 volts, 40 to 63 Amps capacity complete as in repairs all as specified and directed

S&F MCB, 'C' Curve , TPN 415 volts, 10KA, 40 to 100 Amps capacity in the DB complete as in repairs all as specified and directed

S & F LED batten fitting along with removable LED Tube 20W, 230 Volt, wall /ceiling mounted, LED batten fixed by means of bolts, ABS rotor suitable for single side connections. LED rod having glass material complete having lumen efficacy minimum 100 lm/w, CCT 6500 K, CRI>80 ,burning hour minimum 25000,PF - 0.9 powered by integral constant current driver suitable for 230 V AC with all accessories internally prewired including connecting up with twin core twisted flexible copper conductor cable with suitable size complete as in repairs all as specified and directed

S&F LED light fitting mirror type with high output diffuser 2 feet, 10 watt 220 V AC decorative type100 lm/w, CCT 6500 K, CRI>80 ,burning hour minimum 25000, PF - 0.9, with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete as in repairs all as specified

S&F LED light 35 watt 230 VAC outdoor type with thermal management in multiple optics 100 lm/w,CCT 6500 K, CRI>80 ,burning hour minimum 25000,PF-0.9 and equipped with IP66 protection, impact and corrosion resistant with driver and lamp including all electrical connection complete as in repairs all as specified and as directed.

S&F Exhaust fan 300mm sweep copper wound made of sturdy engineering plastic with louvers shutter, voltage 230V, 50 Hz, RPM 1200, including all electrical connection complete all as specified and as directed.

S&F Exhaust fan 300mm sweep copper wound made of sturdy engineering plastic with louvers shutter, voltage 230V, 50 Hz, RPM 1200, including all electrical connection complete all as specified and as directed.

S&F Exhaust fan 450 mm sweep made of steel body AC single Phase. 230V with, blades, and frame and louvers including all electrical connection complete all as specified and as directed.

S&F Water heater storage type, electric, capacity 25 liters BEE 5 star rated including suitable size and length of PVC connection for hot & cold water and fixing arrangement complete with necessary fastener and nut bolts washer etc all electrical connection complete all as specified and as directed

S&F PVC box flush mounted 100mm x 100 mm x 100mm having holes for 20mm conduit entry including 2 pin TV socket outlet flush type duly marked with symbol of TV and 3 mm thick plastic laminated sheet cover complete for telephone connection all as specified.

M&L Rigid non-metallic PVC conduit of size 20 mm dia exclusive of boxes (junction/terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc.complete, all as specified.

M&L Concealed sub main wiring of two run with 4 Sqmm single core PVC insulated, FRSH, flexible multi stranded copper conductor cable 1100 volts grade, drawn through and including PVC conduit pipe 25 mm dia medium grade and accessories of suitable size and fixed on concealed surface of wall/ceiling with cutting chases for conduit including one run of 4.0 Sqmm single core PVC insulated, FRLS , flexible copper cable as earth continuity conductor in green color all as specified and as directed. Note- (a) Two runs of single core cable with one run of earth continuity cable including PVC conduit and its accessories will be measured and paid as one unit). (b) Make good to disturbed surface of wall and floor with existing as directed by Engr in Charge .

M&L Concealed sub main wiring of two run with 6 Sqmm single core PVC insulated, FRSH, flexible multi stranded copper conductor cable 1100 volts grade, drawn through and including PVC conduit pipe 25 mm dia medium grade and accessories of suitable size and fixed on concealed surface of wall/ceiling with cutting chases for conduit including one run of 6.0 Sqmm single core PVC insulated, FRLS , flexible copper cable as earth continuity conductor in green color all as specified and as directed. Note- (a) Two runs of single core cable with one run of earth continuity cable including PVC conduit and its accessories will be measured and paid as one unit). (b) Make good to disturbed surface of wall and floor with existing as directed by Engr in Charge .

Taking down of ceiling fan from any position and depositing to MES store yard and refixing the same on original position after painting, servicing and marking of MES number including replacement of 02 core size 0.75 Sqmm flexible copper wire complete all as specified and as directed

Taking down of geyser 25 ltr capacity and refixing the same on same position including necessari connection complete all as specified and as directed.

M&L Painting to meter panel box installed at bldg stair with synthetic enamel paint of existing colour,after scrapping and one coat painting complete all as specified and as directed..

M & L Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried in ground (earth pit not less than 2.25 Mtr deep below normal ground level with top edge of the plate not less than 1.5 Mtrs below normal ground level, connecting to galvanized iron earth wire 4 mm as earthing lead by means of bolt ,nuts, check nuts and washer of galvanized iron or steel besides welding of all joints as shown in drawing and including excavation and earthwork and earth lead protection by provision of GI light grade pipe 15 mm bore including provision of concrete pit in PCC (1:2:4) type B1 using 20mm graded stone aggregate with 40mm thick cover of RCC (1:2:4) reinforced with XPM (weight not less than 4gs/Sqm) and frame of angle iron 25mm x 25mm x 6mm with lugs 02 Nos and with 6 mm dia MS bar handle made to shape, GI medium grade 20mm bore pipe for watering perforated at the bottom 1.75 meter long placed on top edge of earth plate common salt and charcoal filling test point made out of 40mm x 8 mm FI with fixing arrangements, funnel, wire mesh and earth work in hard dense soil, returning filling in and removal of surplus soil to a distance not exceeding 50 Mtrs all as per electrical Plate No.3 of SSR Part I and connecting to earth test point all as specified or indicated including testing on completion Note: (i) Item includes the cost of 7.5 metre length GI pipe for protection of earth lead and earth lead . (ii) Earth resistance of earth pit should be less than 0.5 Ohms. On testing after completion if the desired earth resistance in not obtained the earthing will be redone at no extra cost

Supply, install, testing and commissioning in replacement of indoor type totally enclosed weather ,dust & vermin proof CPRI approved factory made LT wall mounted meter panel board 415 volt, 3 phase, 4 wires,AC,50 Hz fabricated from 2.00 mm thick CRCA sheet steel and epoxy powder coating in RAL 7032 shade with seven tank treatment process, front opening hinged door with a fully transparent cover made of polycarbonate/high grade engineering plastic to permit clear view of display, locking arrangement, copper busbar 20 mm x 5 mm insulated with heat shrinkable sleeves, appropriate space for fixing single phase energy meter 05 Nos upto 40 amps, fixed with, hold fast/fastener/bolts/copper lugs/spacers/terminal blocks, rubber gasket, locking knobs, phenolic laminated sheets for live isolation ,heat shrinkable sleeves, nuts, bolts, washers, connections from MCCB to busbar, busbar to meter & meter to MCB with single core copper cable of size 10 sqmm connection , R- Y-B LED indications to show 3 phase availability at incomer including the following :- (i) One number MCCB 63 Amps, 415 volts, 4 pole, 16 KA, thermally adjustable between 70 to 100 % (ii) Temper proof electric meters single phase -05 Nos (Refixing the existing) only alongwith sealing, making sticker of Qtr No in suitable size for identification etc all as directed by Engr -in Charge) (iii) Five numbers MCB DP 32 Amp,10 KA, 'C' series as approved (one number in each outgoing side of meter)

Taking down carefully and refixing split ac 1.5/2.0 tr including all accessories and electrical connection complete all as specified and as directed.

Taking down carefully and keep safe custody of decorative light fitting from any position ,capacity and refixing the same position after the civil works including necessary electrical connection complete all as specified and as directed.

S&F Round shape 12 watt COB 220 volts AC CCT 6500K recessed type with high efficiency light complete including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed

S & F Flexible LED strip 5 watt suitable for cove lightening and indirect lightening CCT 6500K RGB type LED strip light 12 v IP20 60 LED Including all electrical connection complete all as specified and directed

S & F SMPS 12 volt flexible LED strip 5 watt, led strip light 12 v IP20 60 LED RGB complete all as specified

S & F LED post top 40 watt (Smart G-3 type) with decorative circular design compliant to dark sky norms with polycarbonate opal diffuser and IP 65/IK-10 protection installed with suitable dia and 3 mtr length powder coated metal pipe complete with all fixing arrangement Including all electrical connection complete as in repairs all as specified and directed.

S & F Stainless steel industrial type commercial chimney with all accessories like blower fans cap 5000 CMH, duct size min 18"x 20" and length min 12 m backward curve/straight/radial straight/open/peddle type, RPM min1450, single phase,230 volt,50 Hz, motor min 0.25 HP capacity complete with all fixing arrangement Including all electrical connection complete all as specified and directed

Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth, for foundation, / laying of pipe / cable etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick using excavated soil all as directed

Removal of surplus soil to a distance n. exc 50 m and depositing where directed at a level n. exc 1.5 m above the starting point complete all as specified and directed

Labour only boring of holes under road, pavement, hard standing by trenchless technology using ultra sound technique/ manually and necessary machine complete all as specified and as directed.

Supply and laying of DWC HDPE pipe of SN4 category conforming to IS 14930 part I and II including accessories like HDPE snap fit coupler with neoprene 'O' ring of 40 mm size.

Supply and laying or fixing XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured electric power cable (H/D) earthed cable aluminium conductor, 1100 volts grade with stranded for 25 sq. mm, 4.0 core nominal cross section in service connections complete all as specified and directed

DMA PROJECTS (BID ID -3256042)

Priya Construction co. (BID ID -3257009)

M/s SK Traders (BID ID -3250193)

Haritwal traders (BID ID -3256976)