Certain repairs to internal, external plastering, painting, roof sheet, plinth protection, joinery, facia, footpath drain work and other misc repairs alongwith E/M related repair works in OTM Accn under AGE B/R-II of GE (KH) YOL

Amount

SCHEDULE 'A' PART-I :- Taking down chowkats or frames including shutters (without taking off shutters from the frame) not exc. 1.5 Sqm each and removing from site, all as specified

Taking down chowkats or frames including shutters (without taking off shutters from the frame) exc. 1.5 Sqm but not exc. 4 Sqm each and removing from site, all as specified.

Taking down shutters of any description exc. 1 Sqm not exc. 2 Sqm each and removing from site, all as specified.

Taking down cement plaster on brick or stone walls, ceiling, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete including removal of debris to a distance exc 1.5 km but n.exc 2 km, all as specified and as directed.

Demolition of brick work or stone/ boulder masonry built in cement mortar including all quoins arches, pillars, including removal of debris to a distance exc 1.5 km but n.exc 2 Km, all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floors and paving, not exceeding 15cm thickness (below or above ground level), un-reinforced including removal of debris to a distance n.exc 100m, all as specified and as directed.

Dismantling wall and ceiling boards (fiber, pulp, insulation etc) or insulation boards/ slabs/ blankets, any thickness including cover fillets in ceiling, all as specified.

Dismantling timber scantlings 40 sqcm and over in section, in any position, framed or unframed work, complete all as specified.

Dismantling timber scantlings in fillets, rails, posts, rafters, purlins, etc. under 40 sqcm in section complete all as specified.

Fly ash brick work with old size bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 (1 cement : 6 coarse sand), complete all as specified.

Plain cement concrete M-10, nominal mix, type C-1, using 20mm graded mechanically crushed stone aggregate, 50mm thick as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), all as specified. Note:- The unit rate include for use of form work (straight or curved).

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing and rubbish of the premisses, complete including removal of debris to a distance exc 1.5 km but n.exc 2 km, all as specified and as directed.

5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing, complete all as specified and directed.

Solid PVC Wall Lining consisting of 5mm thick wood grain (as approved by GE/Enge-In-Charge) printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing all as specified.

Plain cement concrete M-15, nominal mix, type B-0, using 12.5mm graded mechanically crushed stone aggregate as in sub base floors/path, 25mm thick, surface finished even and fair to receive top surface, all as specified.

Mat finish joint less (non skid), Premium class I grade, coloured, ceramic tiles, 7 to 8mm thick (Square/ rectangular) area of each tile exc. 0.06 Sqm but not exc. 0.11 Sqm, in floors and the like, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick screed bedding layer in cement mortar 1:4 (1 cement : 4 coarse sand) complete, all as specified.

Mat finish joint less (non skid), Premium class I grade, coloured, ceramic tiles, 7 to 8mm thick (Square/ rectangular) area of each tile exc. 0.18 Sqm but not exc. 0.38 Sqm, in floors and the like, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick screed bedding layer in cement mortar 1:4 (1 cement : 4 coarse sand) complete, all as specified.

Mat finish, premium quality, coloured/ printed ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, as in skirting, dado etc . set and jointed in neat cement slurry and includingincluding 10mm thick rendering in cement mortar (1:4) including necessary cutting as per site requirement complete all as specified and directed. including necessary cutting and waste as per site requirement pointed in white or coloured cement to match complete all as specified and directed.

Vitrified ceramic tiles light shade, 10mm thick (Square/ rectangular) area of each tile not exc. 0.36Sqm, in floors and the like, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick screed bedding layer in cement mortar 1:4 (1 cement : 4 coarse sand) complete, all as specified.

Vitrified ceramic tiles light shade, 10mm thick (Square/ rectangular) area of each tile not exc. 0.36Sqm, in vertical surfaces such as skirting and the like, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 10mm thick rendering in cement mortar 1:4 (1 cement : 4 coarse sand) complete, all as specified.

Glazed light shade/white tiles of size 350x250/450x350/450x300/600x300x7mm thick as in vertical surfaces such as jointed in neat cement slurry and pointed with white or coloured cement to match and including 10mm thick plastering in cement mortar 1:4 (1 cement : 4 coarse sand) complete, all as specified.

Glazed light shade/ivory/white tiles of size 300x200x7mm thick as in vertical surfaces such as jointed in neat cement slurry and pointed with white or coloured cement to match and including 10mm thick plastering in cement mortar 1:4 (1 cement : 4 coarse sand) complete, all as specified.

Pressed steel frames of size 105x60mmx1.25mm for door with two rebates including necessary fixing lugs, hinges, lock strike plate etc, including back filling with PCC M-15 (nominal mix) type B-0 using 12.5mm graded crushed stone aggregate complete, all as specified.

Pressed steel frames of size 125x60mmx1.25mm for door with two rebates including necessary fixing lugs, hinges, lock strike plate etc, including back filling with PCC M-15 (nominal mix) type B-0 using 12.5mm graded crushed stone aggregate complete, all as specified.

Factory made 2nd class hard wood (Sal/ Hollock) plain, framed, panelled 35mm thick shutters without interlocking rail and with one panel and panels of 9mm BWP commercial plywood or 12mm veneered particle with commercial face veneers on both sides.The size of rail and style as per IS–1003 (Part-I), kiln seasoned and chemically pressure treated, all as specified.

Factory made second class hard wood (Sal) glazed and Skelton door shutters 35mm thick open rebated and prepared to receive glass gauge etc (with sash bars) edges of framing plain chamfered or rounded fitted with cut and mitered beads for securing glass or gauge etc., size of members of shutter as specified in clause 8.24 (a) of part-I, fitted to chowkats, complete all as specified.

Steel window 1.25mm thick box type (Primer coated) ERW hollow P section of size 60mm x 25mm double rebated comprises gauged, glazed skelton shutter ERW Sec 50mm x 20mm and 1mm thick with two openable leaf consiting two Nos sash bar of T-Section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 30mm x 25mm and 1.25mm thick required no of each window, steel duly painted with one shop coat of zinc chromate primer on prepared surfaces) and finishing the surfaces to match with existing including following fitting welded to frame shutter:-(i) Hold fast, 150mm long of 12mm x 3mm made to shape -04 Nos per window. (ii) Handle of Z section 20mm x 25mm, 100mm long -1 No per leaf. (iii) MS tower bolt 150mm long - 2 No per leaf. (iv) Z section 20mm x25mm, 100 long stopper - 1 No per leaf. (v) Cleat 65mm long of hollow square 15mm x 20mm x 63mm welded to hinge -1 No per leaf. (vi) Mild steel pintle hinge of size 75mm x 12mm - 2 Nos per leaf. (vii) Flat iron fillets of size 20X3 mm for fixing wire gauge. (viii) MS work with angle or other section as in window gurad bars, grill (ix) Fabrication & fixing arrangement as per drg No. CEPZ/ TD 26/13. if iron scrap retrived under this item shall be sold to contractor under Sch of credit. Make : As per Appendix 'C'.Note:-(i) Above referred drawing has not been made part of tender. The same can be seen in the office of GE during working hours on any working day.

Stainless steel wire cloth. 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with stainless steel wire staples or wooden beads, complete all as specified.

Factory made solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing on page No 180 of MES SSR 2020 Part-II.

Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of 5 mm thick plain coloured PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site, Sheet No 1/1) specified and directed.

Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge.

Butt hinges (ISI marked), medium weight, cold rolled, mild steel 100mm long, all as specified.

Aluminium anodised, (ISI marked), barrel tower bolts of extruded section, length of bolt 150mm, fixed, all as specified.

Extruded aluminium alloy handles (ISI marked), fabricated type, anodised, of size 150mm, all as specified.

Aluminium alloy, anodised, sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, length of bolt 300mm with lipping frame to match, all as specified.

300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

Small fittings of 2nd class hard wood (SAL) such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including 50mm long, medium weight, cold rolled mild steel butt hinge, articles not exc. 200 cu.cm. each including preparation of articles and applying two coats of synthetic enamel paint over a coat of pink primer, all as specified.

Mild steel work Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165, complete all as specified and directed.

Plain cement concrete M-15, nominal mix, B-1 using 20mm graded mechanically crushed stone aggregate as in lintels upto 1.5 metre clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, chamfered angles and throating, complete all as directed Note :- (i) The unit rate include for use of form work (straight or curved). (ii) Reinforcement if any shall be measured and paid separately.

Rendering plaster 15mm thick in cement mortar 1:6 (1 cement :6 coarse sand) on other than fair faces of brick wall or stone wall surfaces, surface finished even and smooth without using extra cement, all as specified.

Rendering plaster 15mm thick in cement mortar 1:4 (1 cement :4 coarse sand) on other than fair faces of brick wall or stone wall surfaces, surface finished even and smooth without using extra cement, all as specified.

Preparation of newly plastered wall surfaces and applying two coats of oil bound distemper over 2mm thick wall care putty, complete, all as specified.

Two coats of white wash on newly plastered or previously undecorated surfaces of walls including preparation of surfaces complete, all as specified.

Two coats of cement base paint over a coat of primer on newly plastered surface of wall including preparation of surface complete all as specified and directed.

Dismantling boarding, any description, fixed in any position with nails, complete all as specified and directed.

S&F Prelaminted/MDF board 18/19mm thick exterior grade prelaminated one side with decorative choice lamination and other side balancing white lamination and fixed with screws to timber frame work as on wall panelling cup boards shutters (sliding or fixed), complete all as specified and directed.

Extra over rates of block board or veneered particle board for external teak wood lipping, 6mm thick fixed with nails, complete, all as specified.

Hasp and staple, safety type, aluminium with mild steel hinge pin including bolt to hinge plate and fixed with screws of size 75mm, all as specified.

S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised Width of flaps (when open) in 40mm, all as specified.

Dismantling water tanks and removing to store water tanks of capacity up to 1000 ltr, all as specified and directed.

Rotational moulded polyethylene water storage tank 500 Ltrs capacity (Cylindrical vertical with closed top) hoisted and fixed in position inbcluding brass ball valve 20mm dia epoxy coated aluminium rod with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line, all as specified.

Rotational moulded polyethylene water storage tank 1000 Ltrs capacity (Cylindrical vertical with closed top) hoisted and fixed in position inbcluding brass ball valve 20mm dia epoxy coated aluminium rod with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line, all as specified.

Disconnecting existing tanks, setting aside (or lowering, if required) for repair, cleaning and removing all scale and dirt, etc., from water tanks of capacity 250/500 ltr, from mouths of circulating pipes, hoisting, reconnecting and re-fixing in position after cleaning and repairing and making connections with existing water supply line, complete all as specified and directed.

Vitreous Chinaware squatting pan, ‘Orrisa pattern’ size 580 mm x 440 mm, crystal white, with PVC ‘P’ or ‘S’ trap, front or back inlet, integral foot rest with provision of plain cement concrete M-15, type B-I using 20mm graded crushed stone aggregate complete all as specified,including PVC valveless, syphonic action type flushing cistern 10 litres capacity low level with inlet, ball valve, float and handle with brackets with PVC 32mm dia flushing pipe, anti-syphonage pipe, fixed in repair complete, all as specified.

Vitreous China wash down water closet (pedestal pattern), coloured including traps, connection to drain or outgoing pipe, flushing pipe, anti-syphonage pipe complete including fittings, PVC coloured seat cover and chromium plated jet including PVC connection, fixed complete, including PVC valveless, syphonic action type flushing cistern 10 litres capacity low level with inlet, ball valve, float and handle with brackets with PVC 32mm dia flushing pipe, anti-syphonage pipe, fixed in repair, complete all as specified.

Supply and fixed in repair CP jet spray hygenic spray jet for 15mm bore dia fittings 1 to 1.5m long tube acrylic type, complete all as specified.

Supply and fixed in repair PVC valveless, syphonic action type flushing cistern 10 litres capacity low level with inlet, ball valve, float and handle with brackets including 32mm dia PVC long bend flush pipe 90cm long and 15mm dia PVC connection 600mm with CP brass coupling nuts and PVC washers at both ends, fixed complete, all as specified.

Wash basins, Vitreous China (Flat back or angle back type) size 550mmx400mm, crystal white with and including cutting for and pinning on ends of brackets, 450 mm long PVC connections 15mm size with CP coupling nuts at both ends, waste pipe of polythylene of low or high density or PVC of 32mm dia including Pillar taps fancy type, 15mm bore cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, 32mm dia waste fittings, brass chromium plated with long screwed shanks and fly nuts, flange and bedded in red lead cement and other end fixed, screwed for iron pipe and fixed in repair, complete all as specified.

Vitreous China bowl Urinal, flat back 465x355x265mm, white (white (minimum) with grating and union for discharge pipe, complete including providing and fixing plugs, beding urinal against wall in cement mortar 1:2 securing urinal plugs with and including 60mm long brass screws, pointing around urinal back in cement, including 32mm bore PVC waste pipe, complete all as specified.

M&L 32mm dia Low density poly ethylene pipes (LDPE) of pressure rating 6 kg/ sqcm, fixed in wash basin, sinks etc, complete all as specified and directed.

Pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed of 15 mm bore and fixed, complete, all as specified.

Pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed of 15 mm bore and fixed in repair, complete, all as specified.

Bib taps, 15mm bore, cast copper alloy with crutch or butterfly handle, chromium plated screwed for iron pipe or for brass ferrule and fixed in repair, all as specified.

Bib taps, 15mm bore, cast copper alloy with crutch or butterfly handle, fancy type chromium plated screwed for iron pipe or for brass ferrule and fixed in repair, all as specified.

Stop valve, cast copper alloy, fancy, type, chromium plated with long shank and cup (concealed type), screwed down, high pressure with crutch or butterfly handle, screwed both ends for 15mm bore iron pipe or for unions and fixed, complete, all as specified.

Stop valve, cast copper alloy, fancy, type, chromium plated with long shank and cup (concealed type), screwed down, high pressure with crutch or butterfly handle, screwed both ends for 15mm bore iron pipe or for unions and fixed in repair, complete, all as specified.

PVC connection 15mm size with PTMT nuts at boths end 450mm long and fixed, all as specified.

20mm Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed in repair, complete all as specified.

32/40mm bore Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed, complete, all as specified.

Stainless steel heavy FULL SS 75mm to 100mm inches (as per site requirement) kitchen waste coupling for sink/wash basin with Chrome finished, complete all as specified and as directed by Engr-In-Charge.

Dismantling of PVC, cast iron or reinforced concrete drain pipes 100/110mm, jointed in cement mortar and taking out of trenches, if required.

Dismantling of PVC, cast iron or reinforced concrete drain pipes 75mm, jointed in cement mortar and taking out of trenches, if required.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall including fixing clamps etc. of bore 110mm including fixing with rubber ring joints, complete, complete, all as specified.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, as in floors, trenches, of bore 110mm including fixing with rubber ring joints, complete, complete, all as specified.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall including fixing clamps etc. of bore 75mm including fixing with rubber ring joints, complete, complete, all as specified.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, as in floors, trenches, of bore 75mm including fixing with rubber ring joints, complete, complete, all as specified.

PVC (SWR) junction single, (Single T) equal or unequal, 110mm bore, provided with oval access door all as specified.

PVC (SWR) junction single, (Single T) equal or unequal, 75mm bore, provided with oval access door all as specified.

PVC (SWR) floor trap, plain with grating including jointing with solvent cement, dia of outlet 75mm, fixed in repair, complete all as specified.

PVC (SWR) floor trap, plain with grating including jointing with solvent cement, dia of outlet 110mm, fixed in repair, complete all as specified.

PVC (SWR) bends any radius, 75mm bore jointed with solvent cement and fitted with oval access door all as specified.

PVC (SWR) bends any radius, 110mm bore jointed with solvent cement and (fitted with oval access door, all as specified.

Soap dish, vitreous China white, approximate size 160x 160x90mm, chromium plated, fixed to plugs with chromium plated, brass screws fixed in repair, all as specified.

Brass Chromium Plated, tubular towel rail, 20mm dia, D type, 60cm long between flanges, with brackets, fixed with chromium plated screws, fixed in repair, complete all as specified.

Taking up or down 15mm bore, steel tubing and connections, including cleaning for refixing or removal from site, all as specified.

Taking up or down 20mm bore, steel tubing and connections, including cleaning for refixing or removal from site, all as specified.

Mild steel galvanized iron water tubing 15mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor complete, all as specified and directed.

All as per Serial Item No 89 above but except pipe. (Note:- Serviceable pipe retrieved from Serial Item No 87 shall be used).

Mild steel galvanized iron water tubing 20mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor complete, all as specified and directed.

All as per Serial Item No 91 above but except pipe. (Note:- Serviceable pipe retrieved from Serial Item No 88 shall be used).

Dismantling plain or corrugated steel sheeting any gauge, thickness including Nainital or similar pattern roof covering, all as specified.

Corrugated galvanized iron mild steel sheets 0.63mm thick, grade ‘O’, with 120 grams per square metre zinc coating fixed with 'J' or 'L' hook as in roof covering with two corrugation side lap. (Horizontal distance of side lap shall not be less than 145mm and depth of corrugation shall be 12.5mm), all as specified and directed.

All as per Serial Item No. 94 above but except sheet. (Note:- Serviceable pipe retrieved from Serial Item No 93 shall be used).

0.63mm thick plain galvainsed mild steel sheeting in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275, complete, all as specified and directed.

All as per Serial Item No. 96 above but except sheet. (Note:- Serviceable pipe retrieved from Serial Item No 93 shall be used).

Applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer on new steel or steel based surfaces of any description, exceeding 10cm width or girth including preparation of surfaces, all as specified.

2nd class hard wood (sail) as in scantling clean sawn timber fixed in vertical post, for ceiling or roof trusses member, complete, all as specified.

Second class Plain fillets. square, rectangular or triangular in section, clean sawn, secured with nails or brads sectional area exc 13 & n. exc 25 sqcm secured with nails or breads, complete, all as specified.

Second class Plain fillets. square, rectangular or triangular in section, clean sawn, secured with nails or brads sectional area exc 6 & n. exc 13 sqcm secured with nails or breads, complete, all as specified.

Asbestos cement plain building boards, fixed to timber framework with screws, including preparation of surface and applying three coats of white wash complete, all as specified.

Anodised aluminium snap grid frame work (Size of grid 605mmx605mm) for false ceiling all as specified in clause 10.38.1 on serial Page No 216 of SSR Part-I-2009, including Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long including necessary scaffolding all as specified and directed.

4mm thick non asbestos fiber cement building boards (Decorative E Board) as in ceiling flat or sloping fixed or laid/ inserted to timber/GI / aluminium framework fixed with nails, including preparation of surface and applying three coats of white wash complete, all as specified.

Applying two coats of synthetic enamel paint over a coat of pink primer on new wood or wood based surfaces of any description, exc. 10cm width or girth including preparation of surfaces, all as specified.

Anodised aluminium frame for doors, windows, ventilators with Powder Coating (minimum thickness of powder coating 50 micron) with one or more rebates including joining cleat for fixing etc. complete all as specified

Anodised aluminium door shutters power coated, aluminium section weighing 0.55 kg/ m with Powder Coating (minimum thickness of powder coating 50 micron) including necessary joining cleats, glazing clips, ruber neoprene packing, handles 150mm long 2 Nos in each door, hinges 100mm long 02 Nos, anodised aluminum snap beading screws etc. complete all as specified complete all as specified.

Anodised aluminium window and ventilator shutters power coated, aluminium section weighing 0.55 kg/ m with Powder Coating (minimum thickness of powder coating 50 micron) including necessary joining cleats, glazing clips, ruber neoprene packing, handles 150mm long 1 Nos in each door, hinges 100mm long 02 Nos, 01 Peg stay , anodised aluminum snap beading screws etc. complete all as specified complete all as specified.

Taking down aluminium door shutter and refixing the same aluminium door shutter after resecuring/readjusted to aluminium section weighing nit less than 0.55 Kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 150mm long 1 Nos in each door, hinges 100mm long 02 Nos, anodised aluminum snap beading screws etc. and renew unserviceable items such as fittings, sections, glass, solid PVC sheets etc. complete all as specified complete all as specified and as directed by Engr-In-Charge.

Sheet glass 4mm thick ordinary quality and glazing with oil putty wooden beads in squares, not exc. 0.5sqm in each pane, complete all as specified.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips, complete and providing and fixing new one, all as specified.

Transparent fibre glass 3mm thick ordinary quality and glazing with oil putty wooden beads in squares, not exc. 0.5sqm in each pane, complete all as specified.

Mortice lock, brass, vertical type, size 100 mm, 4 lever, fixed into door shutter, fixed in repair, complete all as specified.

Mortice lock, brass, vertical type, size 100 mm, 4 lever, fixed into door shutter, complete all as specified.

Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed in repair, complete all as specified.

Aluminium (diecast) body door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed, complete all as specified.

Aluminium (diecast) body door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed in repair, complete all as specified.

Walling random rubble masonry with best quality locally available stone, uncoursed, well bonded, bedded, solidly hearted and built in cement mortar 1:6 (1 cement : 6 coarse sand), all as specified.

Rolled Mild steel sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc. similar work conforming to Fe.290. Gde-E-165, all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, all as specified and directed.

Harrison 25mm bore Curtain rails, mild steel, chromium plated with fixing brackets, stops and roller etc. fixed in repair complete all as specified.

Sink with drainage board made of stainless steel 1.00 mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, including 40mm dia waste pipe & CP waste coupling ,overall size 915mm x 460mm bowl size 405mm x 335mm x 178 mm, and fixed in repair, all as specified.

Taking down existing unserviceable roof treatment materials and PCC/ cement mortar padding etc complete from roof carefully by cutting chiselling, cleaning the surface by scrapping, brooming, brushing etc and removing the rubbish from site complete, all as directed by Engr-in Charge.

15mm thick (average) screed bed/ plaster in cement mortar 1:4 in order to maintain proper slope and base over existing roof surface for laying of APP, mixed with water proofing compound as per manufacturer instructions finished even and smooth without using extra cement complete, all as specified and directed. (Note:- WPC and APP treatment shall be measured and paid separately)

Applying a coat of bitumen primer conforming to IS:3384-1986 over plastered surfaces @ 0.40 litre/sqm of density 0.87-0.89 Kg/litre at 25 degree centigrade and viscosity 70-160 CPS (Bitumen primer shall be of same make as of memberane) including preparation of surfaces, complete all as specified and directed by Engr-In-Charge.

APP (Atactic Poly-propylene Polymer) modified membrane, five layered, 3mm thick weighing not less than 3.6 Kg/Sqm, having a centre core of polyester non-woven mat (FP) reinforcement dipped into APP modified mix and sealing all the over laps 75mm on length side and 100mm on width side of membrane by torching as per manufactures instructions by authorised applicator only after applying evenly a coat of bitumen VG-10 grade @ 1.20 Kg/Sqm on the bottom of APP and on top of joints of APP, complete all as specified and directed.

Supply only Liquid water proofing compound, complete all as specified.

Stainless steel plate rack of size 600mmx750mmX250mm (nearest higher size) hoisted & fixed in position with drills, PVC rawals plugs and chromium plated screws all as per manufacturers instruction, complete all as specified and directed. Note:- Blue star, Nirali, Prayag

Preparation of old/ untreated walls (washing, rubbing down and stopping of distempered and painted surfaces) and finishing walls with textured exterior paint of required shade, granular finish : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm over and including applying plaster of paris putty of 1mm thickness over plastered surface to prepare the surface even and smooth, complete all as specified and as directed by Engr-In-Charge. Note:- The shade as approved by GE/Engr-In-Charge.

Preparing old plastered/unplastered surface or renewal of décor and wall plates, repair any damages (i.e holes, rough areas etc) using spackle knife, smoothen the wall using sand paper, washing of walls before applying wall paper primer (acrylic based) then apply wall paper (shade as approved by GE/Engr-In-Charge), roll every seam perfectly (using tapping knife, rollers, utility knife etc) clean off any adhesive left on wallpaper perfectly, complete all as specified and directed by Engr-In-Charge.

Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-In-Charge.

Natural colour 15 micron anodized powder coated aluminium door chowkhat with shutter of approved design complete with all fixing arrangements including providing and fixing door handles, tower bolts, hydraullic door closer and mortice lock, hinges, door stopper including neoprene lining. The member shall made out of extruded aluminium sections comprising of:- (a) Shutter vertical member 85.00 x 44.45 x 1.80mm weighing 1.302 Kg/RM. (b) Shutter top member 83.5 x 44.45 x 1.70 mm weighing 1.243 Kg/RM. (c) Shutter bottom member 114.30 x 44.45 x 1.29mm weighing 1.139 Kg/RM. (d) Shutter lock rail 83.5x44.45x1.70mm weighing 1.243 Kg/RM. (e) Anodised aluminium handle, fancy type, 350mm long and aluminium tower bolt of size 150mm. (f) 5.50mm thick tinted sheet glass fixed with alumnium beading, silicon lining and gaskets. (g) Aluminium anodised powder coated frame of door of section 101.6 x 44.45 x 1.75mm weighing 1.367 Kg/M, with flat iron hold fasts and necessary concrete in PCC M-15, type B-1 using 12.5mm graded stone aggregate to fix hold fasts all as directed. Note:- (i) Shutter shall be fixed with heavy floor spring ISI marked and pivot, brass lock with duplicate keys.

Natural colour 15 micron anodized powder coated aluminium window chowkhat with shutter of approved design complete with all fixing arrangements including providing and fixing window handles, tower bolts and mortice lock including neoprene lining. The member shall made out of extruded aluminium sections comprising of:- (a) Shutter vertical member 47.62 x 45.45 x 1.74mm weighing 0.881Kg/RM. (b) Shutter top member 47.62 x 44.45 x 1.14 mm weighing 0.607 Kg/RM. (c) Shutter bottom member 47.62 x 44.45 x 1.14mm weighing 0.607 Kg/RM. (d) Natural colour 15 micron anodised aluminium anodised powder coated frame of chowkhat of section 85x44.45x1.80mm weighing 1.302 Kg/RM, with flat iron hold fasts and necessary concrete to fix hold fasts all as directed. (e) 5.50mm thick tinted sheet glass fixed with alumnium beading, silicon lining and gaskets. (f) The size of Anodised aluminium round handle, fancy type shall be 100mm dia (02 Nos) and aluminium anodised aluminium tower bolt of size 100mm (02 Nos).

Urinal without sensor with fixing accessories set, size 480x300x740mm, complete all as specified and directed. Make:- Jaquar cat Part No. URS-WHT-13255.

Sensor flushing valve for urinal with complete kit (battery operated). Make:- Jaquar Cat Part No. SNR-51097 (suitable for URS-WHT-13255 of jaquar)

Vitreous china wash down water closet (pedestal pattern) with flushing cistern (single piece), coloured of size 800mmx375mmx650mm including traps, trap distance 180mm connection to drain or outgoing pipe, flushing pipe, anti syphonage pipe complete including fittings, PVC coloured seat cover and CP jet including PVC connection, fixed complete and provision of PCC M-15, type B-1 using 20mm graded crushed stone aggregate, fixed in repair, complete all as specified and directed. Make:- Cat Part No. ARS-WHT-39751P of jaquar or equivalent make in Appx 'C'.

S&F toilet paper holder with flap recessed type (stainless steel) of vitreous china fixed to walls with chromium plated (CP) brass screws complete all as specified and as directed. Make:- Jaquar Cart Part No AHS-1553 or equivalent make in Appx 'C'.

Chromium plated (Health Faucet) (ABS Body) suitable for 15mm dia pipe, with 1.25 Meter Long flexible Tube & ABS Wall Hook, including making connections and fixed in position, complete all as specified. Make: Cat Part No. ALD-573 of Jaquar or equivalent in makes mentioned in Appendix 'C').

Wash basins, Vitreous China counter table top (oval shape) size 485mmx395mmx150mm or size as per site requirement, white or coloured fixed in granite counter by making suitable holes, new brackets with and including cutting for and pinning on ends of brackets, 450mm long PVC connections 15mm size with PTMT coupling nuts at both ends, trap, grating and union for discharge pipe, waste, chain and plug and porcelain stopper, waste pipe of polythylene of low or high density or PVC of 32mm dia including 32mm dia waste fittings, brass chromium plated with long screwed shanks and fly nuts, flange and bedded in red lead cement and other end fixed, screwed for iron pipe and fixed, complete all as specified.(Cat Part No JDS-WHT-25909 of 'Jaquar' or equivalent in makes mentioned in Appendix 'C').

Taking down point wiring with aluminium/ copper conductor for light point, fan & socket point/ power point etc. complete including switches, sockets, holders, (batten or pendent type), ceiling rose, switch board, bell/buzzer, bell push, and making good to the disturbed surfaces of wall/ floor etc. to match with existing surfaces including white wash/ colour wash/ distempering to match with existing wall/ floor/ ceiling finishes and all as specified and directed.

Taking down sheet metal enclosure DB, MCB, main switch etc and making good distrubed surfaces to match with existing surfaces, complete all as specified.

Point wiring with 1.5 Sqmm copper conductor FRLS (Multi strand) PVC insulated ISI Marked unsheathed cable in and including concealed PVC conduit medium grade, ISI marked of suitable size with all fittings/ accessories and also including PVC insulated ISI marked unsheathed 1.5 Sqmm copper multistranded conductor FLRS as phase, neutral and earth wire connected to common earth dolly and including concealed pressed steel/ cast iron of suitable sizes (modular sunken box) terminal boxes made from 1.60 mm thick sheet for mounting of switches, sockets, fan regulators, light fittings etc. and modular cover plate as top cover for one light point or one fan/exhaust fan point or one bell point, independent, controlled by one way switch/ push button complete all as specified and directed. Note:-i) Wiring colour code i.e Red/Yellow/Blue for phase, Black for neutral and Green for earth shall be maintained. (ii) Rate of cutting chases, cement plaster, white wash and making surface good as existing surface included in quoted rate. (iii) Point wiring is considered for Modular Switches and sockets. Rate of Metallic Sunken box and modular sheet cover plate and other connected accessories required for modular point wiring included in quoted rate. (iv) Rate of modular switch and sockets will be paid seperately under relevant item.

All as per serial item No '143' above, but for one 3 pin 5 Amps socket outlet on the same board with 2.5 sqmm FRLS PVC copper conductor cable and FRLS PVC insulated, unsheathed 2.5 sqmm stranded copper conductor cable as continous earth wire, all as specified and directed.

All as per serial item No '143' above, but for one 3 pin 5 Amps socket outlet on the independent board with 2.5 sqmm FRLS PVC copper conductor cable and FRLS PVC insulated, unsheathed 2.5 sqmm stranded copper conductor cable as continous earth wire, all as specified and directed.

All as per serial item No '143' above, but for 3 pin 15 amps socket out let on independent with 2.5 Sqmm FRLS PVC copper conductor cable and FRLS PVC insulated, unsheathed 2.5 Sqmm stranded copper conductor cable as continuous earth wire, all as specified.

All as per serial item No '143' above, but for one light point controlled by two way switchs.

M & L for point wiring with 1.5 sqmm (Nominal Area) FRLS PVC insulated unsheathed multi stranded copper conductor, 1100 Volts grade, in and including PVC casing capping/conduit (ISI marked) with accessories such as bends, cross, elbow, tees etc. of suitable size including PVC junction box /MS pressed steel cadmium plated terminal box not less than 1.6 mm thick for mounting switches, sockets, fan regulators etc and 3 mm thick laminated hylam sheet top cover (ISI marked) including continuous earth wire FRLS PVC insulated unsheathed 1.5 Sqmm (nominal area) copper multistranded conductor, 1100 Volts grade, connecting to common earth and earth dolly complete all as specified for one light point/ fan point controlled by one switch Note : (i) Wiring Colour code i.e. Red/Yellow/Blue for Phase, Black for neutral and Green for earth shall be maintained. (ii) Chase cutting if required shall be measured and paid separately under relevant items in this schedule.

All as per serial item No '148' above, but for one 3 pin 5 Amps socket outlet on the same board with 2.5 sqmm PVC copper conductor cable and PVC insulated, unsheathed 2.5 sqmm stranded copper conductor cable as continous earth wire, all as specified and directed.

All as per serial item No '148' above, but for one 3 pin 5 Amps socket outlet on the independent board with 2.5 sqmm PVC copper conductor cable and PVC insulated, unsheathed 2.5 sqmm stranded copper conductor cable as continous earth wire, all as specified and directed.

All as per serial item No '148' above, but for 3 pin 15 amps socket out let on independent with 2.5 Sqmm PVC copper conductor cable and PVC insulated, unsheathed 2.5 Sqmm stranded copper conductor cable as continuous earth wire, all as specified.

All as per serial item No '148' above, but for one light point controlled by two way switchs.

Cutting chases in brick walls, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth, complete all as specified.

Supply and fix modular switch piano flush type one way 6 Amps, 1 module, 230V, Fixed complete all as specified.

Supply and fix modular switch piano flush type one way 16 Amps, 1 module, 230V, Fixed complete all as specified.

Supply and fix modular switch piano flush type two way 6 Amps, 1 module, 230V, Fixed complete all as specified.

S&F Modular socket 6 Amp 3 Pin, two module 230 Volts.

S&F Modular socket 6/16 Amp 5 Pin, two module 230 Volts.

Supply and fix modular bell push with indicator 6 Amps, 1 module Fixed, complete all as specified.

S&F Modular fan regulator step type 100 Watt one module 230 volts.

Ceiling rose, three phase, PVC/Polycarbonate, insulated body, fixed in repair all as specified.

Lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings, fixed in repair, complete all as specified and directed.

Supply and fixed in repair LED Bulb 9 watt, cool/warm white 6500K/3000K, suitable for base B22/E27, 230V, complete all as specified and directed.

Supply and fixed in repair LED invertar Bulb 12 watt, cool/warm white 6500K/3000K, suitable for base B22/E27, 230V, complete all as specified and directed.

Supply and fix in repairing LED Adore 2.8 W having base suitable for B22/ E27/ E14 holder CDL Candle Lamp, WW/ CDL, 6500/3000 K, 230 volts complete all as required at site and directed by Engr - in - Charge. Make:Havells / Polycab/Bajaj /CG

Supply and fix in repair modular Bell Push with indicator 6 Amps, 1 module including all As per existing make complete all as specified and directed by Engr-in- Charge.

Supply and fix in repair modular fan step regulator, 2 Module including all As per existing make complete all as specified and directed by Engr-in- Charge.

Supply and fix modular cover plate with frame, 1 module including all As per existing make complete all as specified and as directed by Engr-in- Charge

Supply and fix modular cover plate with frame, 3 module including all As per existing make complete all as specified and as directed by Engr-in- Charge

Supply and fix modular cover plate with frame, 8 module including all As per existing make complete all as specified and as directed by Engr-in- Charge

Supply and fix modular cover plate with frame, 10 module including all As per existing make complete all as specified and as directed by Engr-in- Charge

Supply and fix modular cover plate with frame, 12 module including all As per existing make complete all as specified and as directed by Engr-in- Charge

Supply and fix modular metal flush box 3 module Fixed in repair, complete all as specified.

Supply and fix modular metal flush box 8 module Fixed in repair, complete all as specified.

Supply and fix modular metal flush box 10 module Fixed in repair, complete all as specified.

Supply and fix modular metal flush box 12 module Fixed in repair, complete all as specified.

Supply and fix modular metal flush box 1 module Fixed in repair, complete all as specified.

Single pole and neutral enclosure with a two pin and earth plug top and socket complete with one double pole MCB 20 Amps, complete all as specified.

Sheet metal enclosures factory made for DBs when MCBs to be used, single pole and neutral (double Door), 8 way, 240 volts with 200 Amp rated bus bar, all as specified.

Sheet metal enclosures factory made for DBs when MCBs to be used, single pole and neutral (double Door), 12 way, 240 volts with 200 Amp rated bus bar, all as specified.

Supply and fix distribution board iron clad TPN DB double door with IP-43 protection 415 V 3 Phase 50 HZ 4 Way complete with appropriate size of copper busbar and neutral link complete and incl cutting chasing to wall for fixiing DB and making good the disturbed wall to match with existing surface, incuding taking out old, complete all as specified.

M & L for vertical DB iron clad factory made TPN 4 Way, MCCB as incomer and MCB SP as out going, double door DB IP 43 protection level, incl Blanking plate, lugs etc complete and neutral link with one MCCB 4 pole 415V 100 Amps rating with rupture capacity 16KA incl connection, fixing flushed to wall, necessary grouting, making good with CM 1:4 and painted to match exisitng wall color, incuding taking out old, complete. (outgoing MCB will be measured seperately)

MCB SP 6 to 32 Amp, 240 Volts, 10 KA, C series including taking out old, all as specified. Note:- The connection to the MCBs shall be done through thimble/lugs do not direct wire shall be connected to MCBs.

MCB SPN 32 Amp, 240 Volts, 10 KA C series including taking out old, all as specified. Note:- The connection to the MCBs shall be done through thimble/lugs do not direct wire shall be connected to MCBs.

MCB SPN 63 Amp, 240 Volts, 10 KA C series including taking out old, all as specified. Note:- The connection to the MCBs shall be done through thimble/lugs do not direct wire shall be connected to MCBs.

MCB TPN 63 Amp, 415 Volts, 10 KA C series including taking out old, all as specified. Note:- The connection to the MCBs shall be done through thimble/lugs do not direct wire shall be connected to MCBs.

S & F MCB, 4 Pole, 63 A capacity, 415 V, 10 KA, C series including taking down old MCB 4 Pole. Note: The connection to the MCBs shall be done through thimble/ lugs do not direct wire shall be connected to MCBs.

S & F MCB, 4 Pole, 100 A capacity, 415 V, 10 KA, C series including taking down old MCB 4 Pole. Note: The connection to the MCBs shall be done through thimble/ lugs do not direct wire shall be connected to MCBs.

M & L for sub main wiring with two single core PVC insulated unsheathed, 1100 Volts grade, (FRLS) copper cable 6 sqmm stranded conductor and drawing through and including rigid PVC non metalic surface conduit medium duty (ISI Marked) with conduit accessories such as junction boxes, bends, tees etc. including continuous earth wire PVC insulated unsheathed 1100 volts grade, cable 6 sqmm copper conductor and connected to common earth dolly complete as directed including taking down old submain wiring. Note :-(i) One run of PVC conduit, two runs of cable (Phase + Neutral) and one run of earth wire shall be measured and paid as one unit.

M & L for sub main wiring with two single core PVC insulated unsheathed, 1100 Volts grade, (FRLS) copper cable 6 sqmm stranded conductor and drawing through and including rigid PVC non metalic surface casing caping medium duty (ISI Marked) with conduit accessories such as junction boxes, bends, tees etc. including continuous earth wire PVC insulated unsheathed 1100 volts grade, cable 6 sqmm copper conductor and connected to common earth dolly complete as directed including taking down old submain wiring. Note :-(i) One run of PVC casing caping, two runs of cable (Phase + Neutral) and one run of earth wire shall be measured and paid as one unit.

M & L for sub main wiring with two single core PVC insulated unsheathed, 1100 Volts grade, (FRLS) copper cable 4 sqmm stranded conductor and drawing through and including rigid PVC non metalic surface conduit medium duty (ISI Marked) with conduit accessories such as junction boxes, bends, tees etc. including continuous earth wire PVC insulated unsheathed 1100 volts grade, cable 4 sqmm copper conductor and connected to common earth dolly complete as directed including taking down old submain wiring. Note :-(i) One run of PVC conduit, two runs of cable (Phase + Neutral) and one run of earth wire shall be measured and paid as one unit.

M & L for sub main wiring with two single core PVC insulated unsheathed, 1100 Volts grade, (FRLS) copper cable 4 sqmm stranded conductor and drawing through and including rigid PVC non metalic surface casing caping medium duty (ISI Marked) with conduit accessories such as junction boxes, bends, tees etc. including continuous earth wire PVC insulated unsheathed 1100 volts grade, cable 4 sqmm copper conductor and connected to common earth dolly complete as directed including taking down old submain wiring. Note :-(i) One run of PVC casing caping, two runs of cable (Phase + Neutral) and one run of earth wire shall be measured and paid as one unit.

Supply and fixing in repair LED luminaire 300 mm x 300 mm, 15/18 watt, 220 V AC recessed type complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as required at site and directed by Engr - in - Charge.

Supply and fixing in repair LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as required at site and directed by Engr - in - Charge.

Replacement of LED Decorative ultra slim square profile LED lighting integral type fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use pack, 10 watt LED, 230V, and making connection with 2 core copper flexible cable of size 23 x .0076 from ceiling rose/ PVC connector to light complete, all as specified and directed.

Replacement of LED Decorative ultra slim square profile LED lighting integral type fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use pack, 20 watt LED, 230V, and making connection with 2 core copper flexible cable of size 23 x .0076 from ceiling rose/ PVC connector to light complete, all as specified and directed.

S&F in repair LED tube light fitting integral type 1x 20 W, 230V, LED tube light fitting 3 in 1 light (Cool day light, normal white and warm white in one fitting) with extruded polycarbonate, environment friendly, energy efficient ready to use complete with all accessories internally prewired and including connecting up with twin core twisted flexible copper conductor cable with suitable size including dismantling of unserviceable tube light all as specified and directed.

Supply and fixing of 30 Watt New generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high power LED as lighting source and lens enbedded PC cover having TOP opening seperate toughtned glass/verminproof driver compartment, SPDs with IP66 protection and impact resistance of IK07, suitable for pole dia 43mm (max) connecting with PVC insulated three core flexible copper conductor of suitable size from ceiling rose to fitting including bracket of size 32mm dia lenght 1.2m along with clamps, including taking down old light, complete all as specified and as directed.

Supply and fixing decorative wall lighr fixture made up of polycarbonate, with 9W LED lamp B22 base complete with all accessories internally prewired and including connecting up with twin core twisted flexible copper conductor cable with suitable size, including taking out old light, complete all as specified and directed.

Material and labour for PVC Casing & Caping of size (20 x 12) mm ISI Marked suitable for electrical wiring complete all as specified incl taking out old and directed.

Material and labour for PVC Casing & Caping of size (25 x 16) mm ISI Marked suitable for electrical wiring complete all as specified incl taking out old and directed.

Material and labour for uPVC electrical conduit pipe of size 20 mm dia (heavy duty) Ivory color ISI marked suitable for electrical wiring including junction box, tees and bends etc incl taking out old complete all as spd and directed.

Material and labour for uPVC electrical conduit pipe of size 25 mm dia (heavy duty) Ivory color ISI marked suitable for electrical wiring including junction box, tees and bends etc incl taking out old complete all as spd and directed.

Material and labour for PP Corgulated flexible Conduit pipe of 16 mm dia suitable for internal wiring incl taking out old complete all as specified and directed.

Material and labour for PP Corgulated flexible Conduit pipe of 20 mm dia suitable for internal wiring incl taking out old complete all as specified and directed.

Material and labour for PP Corgulated flexible Conduit pipe of 25 mm dia suitable for internal wiring incl taking out old complete all as spd and directed.

Material and labour for electrical round sheet PVC material used for covering junction boxes, fan mounting and other electrical opening on wall incl taking out old complete all as spd and directed by Engr - in - Charge.

Supply and fixing in repair MCB Protected socket (modular AC box) 3 Module with MCB SP of capacity 25 Amp and power socket for geyser complete all as spd and directed by Engr - in - Charge.

Rendering plaster 15mm thick in cement mortar 1:6 (1 cement :6 coarse sand) on internal fair faces of brick wall or stone wall surfaces, surface finished even and smooth without using extra cement, all as specified.

Material and labour for repair of wooden/ metal box fitted on site for protection of 2 to 4 Nos meter boxes / DB Boxes by dimentling existing unsv hinges, doors and locking arrangements and other part etc and replacing with new hinges, doors, locking arrangements and other parts as required at site and directed by Engr- in- Charge including painting the complete box with paint as directed by Engr - in - Charge.

Taking down ceiling fan of any sweep, any size/make from existing position of any height by disconnecting electrical connections and transporting to workshop. Inspection of ceiling fan in presence of Engr-in-charge/JE (or rep of department) after dismentling spares parts. Transporting ceiling fan back from work shop to site including hanging/ fixing and connecting up and testing etc complete all as required at site and directed by Engr - in - Charge.

M&L for complete repair and maintenance of unserviceable ceiling fan of 1200mm/1400mm sweep at work shop, incl dismantling complete the ceiling fan parts i.e. blades, fan rod, canopy, connection, inspecting serviceability of all the parts, re fixing of serviceable parts after cleaning and replacement of unserviceable parts with company's genuine parts i.e. capacitor, bearing, bushes, shaft, bracket, rubber bush, connecting wire, PVC connector, aluminium clamp for rod, bracket, bush rod, blade and greasing/oiling etc assembling, cleaning and testing of ceiling fan as directed.

Removing of old burnt winding wiring any type, cleaning stator complete for burnt wiring, carbon residue and rewinding of stator winding of any type/any make fan/ any stator design ceiling fan of 1200mm sweep with superior quality super enameled winding copper wire of existing specification, gauge and weight with superior quality insulation for satisfactory functioning fan in presence of JE incharge complete all as directed by Engr-in-Charge.

Taking down carefully exhaust fan of any sweep, any size/make from existing position of any height by disconnecting electric connections and transporting to workshop. Inspection of ceiling fan in presence of Engr-in-charge/JE (or rep of department) after dismentling spares parts. Transporting exhaust fan back from work shop to site including hanging/ fixing and connecting up etc complete all as required at site and directed by Engr - in - Charge.

M&L for complete Repair and maintenance of unserviceable exhaust fan of any sweep at work shop, including dismantling complete the parts i.e. blades, fan rod, canopy, fan cover, connection, inspecting serviceability of all the parts, re fixing of serviceable parts after cleaning and replacement of unserviceable parts with company's genuine parts i.e. capacitor, bearing, bushes, shaft, connecting wire, PVC connector and greasing/oiling etc assembling, cleaning and testing of exhaust fan as directed.

Removing of old burnt winding wiring any type, cleaning stator complete for burnt wiring, carbon residue and rewinding of stator winding of any type/any make fan/ any stator design exhaust fan of any sweep with superior quality super enameled winding copper wire of existing specification, gauge and weight with superior quality insulation for satisfactory functioning fan in presence of JE incharge complete all as directed by Engr-in-Charge.

Taking down water storage heater (Geyser) of 15/25/35/50 liters capacity from electric socket and disconnecting from PVC connection, water supply and replacement of syphon assembly, unserviceable parts, and refixing at same / different location after cleaning of geyser tank, refixing the same duly grouting nuts, bolts washers and connecting to existing water connection complete, all as specified and as directed by Engineer-in-Charge. complete all as specified.

Supply and replacement of heating elements 1.5/2.0/3.0 KW 230V ISI marked round base, triangular base suitable for water heater of any type including connection with suitable cable complete, all as specified and directed by Engineer-in-Charge. Make:-Theeta/Racold/Airex

S&F in repair for thermostat switch and capillary thermostat switch of geyser 230V, (adjustable range bewteen 0 degree to 90 degree centigrade temp range), ISI marked as per existing thermostat suitable for hot water storage heater 15/ 25 / 35 / 50 Ltr, complete all as specified and as directed.

S&F in repair for defective steel inner tank of 15/25/35/50 Litres capacity geyser tank made out of steel sheet 2 mm thick suitable for 6/9 hole assembly complete, all as specified and as directed by Engineer-in-Charge.

Replacement of earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of plate not less than 1.5m below ground level, connecting to galvanised iron wire 4.0mm dia (as earth lead wire), by means of bolt, nuts, check nuts and washer of galvanised and earth wire protected by provision of galvanised iron pipe light grade, 15 mm bore including provn of concrete pit in plain cement concrete M-20 type B-1 using 20mm graded crushed stone aggregates with 40mm thick cover of rainforced cement concrete M-20 reinforced with XPM (weight not less than 4 kg/Sqm) and frame of angle iron 25x25x3mm with lugs 2 Nos and with 6mm dia mild steel bar handle made to shape, galvanised iron medium grade 20mm bore pipe for watering perforated at bottom 1.75 metre long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorous bronze with fixing arrangement, funnel, wire mesh and including earth work in any type of soil, returning filling in and removal of surplus soil to a distance not exceeding 50 metre, all as per electrical plate No. 3 of SSR 2009 Part-I and connection to earth test point all as specified and testing on completion. NOTE :- Item of earthing includes the cost of 7.5 m long galvanised iron earth wire 4mm size and protection pipe of 15mm bore galvanised iron light grade and earth work.

M/S JATINDERA ENTERPRISES