ADDN ALTN TO BLDG NO P 19 OFFICERS HOLIDAY HOME AT RANIKHET UNDER GE RANIKHET

Amount

BOQ/Sch 'A' B/R portion Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises.complete all as directed.

M & L for screed bed or bedding layer 15mm thick in cement mortar(1:6) for laying floor finishes Complete all as specified and directed.

M & L for non skid ceramic coloured /printed tiles 7 to 8 mm thick (square / Rectangular)area of each tiles not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match the tiles.

M&L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 for backing of Dado/ Skirting & Vertical Tiles.

M & L for Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M & L for glazed ceramic coloured / printed tiles 450 x 300 x 7mm on vertical surfaces set and jointed in neat cement slurry and pointed in white/coloured cement to match the tiles, complete all as specified and as directed.

M & L Black Granite (of any type) tiles 20 mm thick machine cut , bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishig types in cooking platforms and like Complete all as specified and directed.

Demolition of Reinforced cement concrete of any description and in any position not otherwise specifically provided for. (reinforcement cut as required to facilitate demolition)

M & L Type B1 1:2:4 (20mm graded aggregate)for Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed

M & L Type B1 1:2:4 (20mm graded aggregate) for chajjas in floors complete all as specified and directed

Formwork to rough finished surface of concrete soffits and sides of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200m thick (Horizontal or sloping)

M & L for TMT bars 6mm to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness.(below or above ground level) Complete all as specified and directed.

M & L for 75 mm thick PCC (1:3:6) type C2 using 40mm graded stone aggregate as in plinth protection finishing the surface even and smooth without using extra cement including mecessary formwork for edge all as specified and directed. NOTE : 10mm wide & 75 mm deep joints shall be made at 3 mtr interval and at each corner and the same shall be filled using bitumen 85/25 and sand in ratio of 1:3.

Taking down cement or cement lime plaster of any description on brick or stone walls, etc. including racking out joints, hacking for key, scrubbing down with water etc.&removing rubbish to a disance not exc 250m Complete all as specified and directed.

M&L for rendering 15 mm thick readymade plaster on inner/outer walls by adding 17-19% of potable water by weight of material for thickness above 15mm "Make: Equivalent of Fosroc/ Sika/ Ultratech/ Choksey etc". it is recommended to be applied in multiple layers. ready mix plaster shall complies with IS 1661-1972, IS 2250-1965, IS 2402-1963 and confirms the compressive strength @ 28 days 10-12 Mpa/Bulk density 1500-1600 Kg/m3. (Note : The rate quoted by contractor shall include cleaning of surface, application as per instruction and scaffolding upto 20 Mtr ht all as specified and directed)

M&L for rendering 5 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:3 and finished smooth and even in ceiling without using extra cement.

M/L for preparing newly plastered wall surfaces and applying two coat of distemper oil emulsion over 1mm thick wall care putty, complete all as specified .

Material & Labour for applying Two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives@ 1.43 litre/ 10 sqm over and including primingcoat of exterior primer applied @ 0.90 litre/ 10sqm over new surfaces complete all as specified and directed.

Material & Labour for complete removal of existing treatment of old plastered surfaces & applying Two or more coats of 100% remium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives@ 1.43 litre/ 10 sqm over and including primingcoat of exterior primer applied @ 0.90 litre/ 10sqm over old surfaces complete all as specified and directed.

M/L for complete removal of existing treatment for preparing old painted surfacess and applying two coat of distemper oil emulsion over a coat of primer over a coat of 2 mm thick wall care putty on wall surfaces including cornices etc for proper levelling of plaster complete all as specified and directed.

M&L for preparing newly plastered surfaces of ceilings and applying three coats of white wash complete all as specified and directed.

Demolition brick work or stone/ boulder masonery built in cement mortar including all quoins , pillars etc

M&L for brick work using sub class ‘B’ old size bricks, straight or curved on plan exceeding 6m mean radius, built in CM (1:6) complete al as specified

Taking down chowkhat or frames with shutters not exc. 1.5 sqm each complete all as specified and directed.

Taking down chowkhat or frames with shutters exc. 1.5 sqm but not exc. 4 sqm each complete all as specified and directed.

Refixing of chowkhat with shutter of any description not exceeding 1.5 Sqm each complete all as specified and directed.

Refixing of shutter of any description in other opening shutter exceeding 1 Sqm but not exc. 2 Sqm each complete all as specified and directed.

M&L for Pressed steel frames 125X60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc.,supplied and fixed complete all as specified and directed.

S&F factory made 35mm thick Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated all as specified

S & F 35 mm thick Second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., rs, edges of framing plain, chamfered complete all as specified and directed.

S&F for 200 MM, ordinary rat tail rod pattern springs (Mild Steel) including roller and roller plate complete all as specified and directed

S & F 150 mm long Mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed.

S & F floor door stopper of chromium plated body with rubber shoe fixed in door, overall length of cover plate 140 mm all as specified and directed.

S & F butt hinges, medium weight, Miled steel and fixed, size of hinges 100mm complete all as specified and directed.

S & F 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

Supply and fix 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy complete all as specified and directed.

M & L for 18mm thick UV coating, MDF board exterior grade, both side laminated with any colour anti fungal, moisture resistance, anti borer as per IS 14587 for kitchen/cupboards shelfs fixingwith 1st class hard wood lipping /breading etc, complete all as specified and directed. Make:- Action tessa/Green ply/Century

Supply and fix Continuous (piano) hinges width 40 mm mild steel , bright finish or eletrogalvanised complete all as specified

M & L for newly painting to steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described with two coats of synthetic enamel paint over a coat of red oxide primer including preparation of surfaces complete all as specified and directed.

S & F in Repair Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with Stainless steel wire staples.

Hacking out old broken glass ( any thickness ) size or description from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads

S & F 3 mm thick Sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane complete all as specified and directed.

M & L for painting to new wood and wood based surfaces of any description, over 10 cm in width or girth, not otherwise described with two coats of synthetic enamel paint over a coat of pink primer including preparation of surfaces.

M&L for preparation of old painted wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of Synthetic enamel paint (Ordinary tint) complete all as specified and directed.

Taking up or down 15 mm bore steel tubing and connections, including cleaning for refixing or removal to store.

Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store.

Cutting chases, for water tubing or concealed , etc, and making good to facings where required and plastering in cement mortar (1:4) cutting not exceeding 10cm girth in brick walls complete all as specified and directed.

S&F GI water tubing of 15mm dia ,medium grade conforming to IS-1239(Part -1) including all fittings such as bends,tees,short pieces,connectors,elbows,reducers,union dockets etc & fixed to walls,ceilings, & laid on floors complete all as specified and directed.

S&F GI water tubing of 20 mm dia ,medium grade conforming to IS-1239(Part -1) including all fittings such as bends,tees,short pieces,connectors,elbows,reducers,union dockets etc & fixed to walls,ceilings, & laid on floors complete all as specified and directed.

S&F in repairs stop valves/angle valves, cast copper alloy, fency type chromium plated , screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed for 15mm bore dia of pipe.

S&F in repairs stop valves, cast copper alloy, fancy type chromium plated with long shank & cup (concealed) , screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed for 15mm bore dia of pipe.

S & F vitreous china wash basin, white, flat back, size 550mm x 400mm, (flat back or angle back type) including brackets and including cutting for and pinning in ends of brackets or erecting stand, fixed in repairs. Make i ( Jaquar cat Part No:- FNS-WHT-40801 ii ( Cera cat Part No :- 1067 A or Hindware Equivalent.

S & F in repairs 15 mm bore Fancy type pillar taps, Cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed. Make i ( Jaquar cat Part No:- COP -001BPM ii ( Marc cat Part No :- MFX- 2010 or Cera Equivalent.

S & F in repairs 15 mm bore Fancy type chromium plated Wall Mixer with or without (as required at site) provision for overhead shower with 115mm long bend pipe on upper side, connecting legs and wall flanges, screwed down high pressure with or without lettered hot and cold screwed for iron pipe complete all as specified and directed .Make i ( Jaquar cat Part No:- FUS- 29281 ii ( Marc cat Part No :- MDM - 2350 or Cera Equivalent.

S&F 32mm dia waste fittings, brass, chromium plated for glazed ware sinks, basins, etc with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed.

S&F 40mm dia waste fittings, brass, chromium plated for glazed ware sinks, basins, etc with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed.

S & F in repairs bib taps, cast copper alloy, 15 mm dia, Chromium Plated, fancy type with crutch or butterfly handle, screwed down for iron pipe and fixed etc complete all as specified. Make i ( Jaquar cat Part No:- KUP- 35037 PM ii ( Marc cat Part No :- MFX - 2170 or Cera Equivalent.

S&F One piece Vitreous china wash down water closet (Pedestal Pattern) Size 655X355X730MM "snow white" with duroplast slim soft close seat cover & twin flush fittings, toilet paper holder, health fuaucet, PVC connection, angular stop cock (valve) (2 Nos) with flange etc all as specified in particular specifications. Note: Vitreous china wash down water closet (Pedestal pattern) cat Part No S1013208 trap 100mm of Cera or equivalent model of make specified.

S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified

S&F in repairs Gun-metal, globe or gate valves 15 mm, with iron wheel head, screwed both ends for iron pipe and fixed

S&F in repairs Gun-metal, globe or gate valves 20 mm, with iron wheel head, screwed both ends for iron pipe and fixed

S&F Prayag hanging system and clamps support and holes with screws and back support rectangular mirror cabinet 400 X 500 (Cat No. 554) and fixed to plug with screws and cup washers complete all as apecified & directed

M & L for 32mm bore high density polyethylene pipes (HDPE) complete all as specified and directed.

S&F in repair for PVC (SWR) floor trap 75 mm, plain with grating including jointing with solvent cement complete all as specified and directed

S&F in repair for PVC (SWR) pipes 75 mm single socketed, in any length with rubber ring joints, fixed to walls

S & F in repair PVC (SWR) 75 mm pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S & F in repair 75 bore PVC (SWR) bends any radius complete all as specified and directed.

S & F in repair PVC (SWR) vent cowls 75mm dia complete all as specified and directed..

S&F brass chromium plated tubular towel rail, 20 mm dia, D; type, 60 cm long between flanges complete all as specified and directed.

S&F chromium plated Soap disk fixed to plug with chormium plated brass screws all as specified and directed

S&F sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S & F in repairs Stainless steel wall mounted plate rack of size 780mm x760mm x 240mm, thickness of sheet not less than 1.0 mm and weight not less than 7.50 kg of approved design/pattern (as approved by Engr-in-charge) with provision for keeping plate and other crockery, fixed with screw and rawl plugs etc on wall complete Make as approved by GE

S&F in repairs Chromium plated shower rose 125 mm swivel type, complete all as specified and directed

S & F 20mm Dia Aluminium alloy anodised curtain rod decorative fency type with brackets complete all as specified.

S & F PVC connections 15mm dia , 450mm long, , with PTMT nuts & washers at both ends

Dismatling PVC Water tank Exc 250 & n exc 500 ltr and removing from site as specified and directed

S & F Rotational moulded PVC water storage tanks 500 Ltrs capcity three layer (cylindrical vertical with closed top) hoissted and fixed in position all as specified

S and F Ball brass valve 20 mm dia high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule complete all as specified and directed.

M & L for roof surface must be pressure-washed with water with, is to be used to and/ or remove all dirt, dust, chalking and waste products. Remove algae, mold by using bleach solution. 2 tiles joint repair all visible and joint more than 0.50mm and not giving hollow sound, on the tiles roof or at the junctions of flat roof & vertical parapet wall, pipe joints, should be cut and widen v shape with mechanical cutter in the size (6mm W x 6mm D) and fill with Dr. Fixit PMM methodology.Glass fiber apply Dr Fixit URP or Primeseal A on the well prepared groove, allow to cure tack free. Followed by filling all the joints covering the entire area uniformly with suitable chemical. Allow chemical to cure a minimum 24 hours. Apply minimum 50mm-100mm width 45 GMS glass Fibre mesh/ non-woven geo testile fleece with the coat of Dr Fixit Roofseal classic along the length of crack when the 1st coat is still in wet condition. Apply the second coat with an interval if 4-6 hours. Waterproofing: Apply a coat of Dr Fixit Roofseal classic (diluted with water in the ratio 2:1) as Self Priming 14.0-18.0 Sq. mt/litre.Allow coating to dry for 3-4 hours. Applt two coats of Dr Fixit Roofseal classic/litre/coat, without, the rate of application being the same for both the coats. This would ensure correct consumption of material that will deliver a total of DFT of microns. Allow the system to air cure for 5 days minimum. Check to see no void surface is left untreated/uncoated. The material having following technical specification as per ASTM D 6083 M- type II, Attains a Tensile strength of 2.5 N/mm2 confirming to ASTM D 2370: Elongation at break > 300% confirming ASTM D 2370, Adhesion to Concrete 2.0N/mm2 Confirming ASTM D 4541 and crack bridging ability up to 2mm, air cure the coating for 7 days before water pound test for 48 Hrs. The system comes with 7 year waterproofing warranty from service provider. For vertical surface : Apply 2 coat of Dr Fixit Roofseal classic with forced coverage of /litre/coat. Entire terrace should be coated with roofseal classic alongwith parapet walls needs to be enveloped with roofseal classic/Raincoat system. The total 3 coats treatment inclu taking down/dismantling of old tarfelt/old unserviceable roof treatment from RCC roof by scrapping, broomig and washing with water etc . Make : Dr Fixit or equivalent (Note : The treatment should be carried out through authorised applicator only)

M & L for providing plain cement concrete type B-1, 1:2:4 (using 20 mm graded crushed stone aggregate) as in coping, bed block for embedding hold fasts, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work as required complete all as specified and directed.

S & F FI as in clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles complete all as specified and directed.

Supply only Water proofing compound complete all as specified

S & F CABINET HANDLE, Finish Type: Stainless Steel complete all as specified and directed.

S&F hollow wall lining dual colour consisting of 5 mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specification and drawing complete fixing arrangement icluding taking down old existing wooden panelling complete.

S&F three track aluminum powder coated sliding window with three sliding shutter , the size of outer frame three track 100 x 37x 1.50mm ( using two track for glazed window shutter and one track for wire gauged ) , the section shutter size 37x 18x 1.2mm)and glazing with 5 mm thick Transparency glass of poly carbone including all-around suitable rubber gasket and stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.4mm and fixed on aluminum flat and inserted in the frame of shutter with tracking arrangement each sliding window shall be provided with one number handle including locking arrangement & 2 numbers’s sliding rollers of nylon with including all necessary fittings

Surface Excavation in hard/dense soil n,exc 30cm deep and averaging 15cm deep and getting out complete all as specified and directed.

M & L for hard core of gauge not exc. 63mm, deposited, spread and leveled in layers not exc. 15 cm thick, watered and rammed to a true surface using broken stone or boulders complete all as specified and directed.

M&L 75 mm thick cement concrete 1:4:8 type D-2 finished fair and even as in sub base Complete all as specified and directed.

M&L for chequred cement concrete tiles of size 300x300x25 mm thick coloured rubber pressed glossy finish, set and jointed in neat cement slurry and pointed in white or colour cement and match the surace of tiles as foor/staps, complete as all specified and directed.

M/L Cement concrete 1:3:6 type C-1 using 20mm graded stone aggregate in cills, seismic and other similar bands, plinth courses, copings, bed plates, bond stones, etc including weathering, slightly rounded or chamfered angles and throating as directed including necessary form work complete.

Removing Excavated soil exceeding 250 M but not exceeding 500M and depositing where directed at a level not exceeding 1.5 M above the starting point complete all as specified and directed.

M/LCement concrete 1:3:6 type C-1 using 20mm graded stone aggregate in surface channels and drains complete.

Extra for forming fair finished drain or channel 30 cm inner girth in cement complete all as specified and directed. concrete, using ex- tra cement, including forms, moulds, mi- tred/stopped ends etc.All as specified and directed.

BOQ/Sch 'A' E/M portion Taking down carefully aluminium/copper wiring of any size (for light, fan, socket or power etc complete) including fixture and fittings such as switches, sockets, ceiling roses, pendent holders regulators, tube lights etc and making good disturbed surfaces of wall, roof etc to match with existing surface.

M & L point wiring for modular fittings for one light point/ fan/bell/ 5Amps socket out let (independent) point controlled by one, one way switch with 1.5Sqmm size, PVC insulated and unsheathed 1100volts grade, single core stranded (multistrand) copper conductor (FR-LSH) PVC cable drawn into & including medium grade PVC conduit (not less than 20mm outer dia ) with all fittings and accessories fixed concealed (including chase cutting in brick/ stone masonry walls for fixing conduit and plastering and whitewash/colouring the external surface and matching the same with existing surface) including modular metal flush box for mounting modular fittings and covered with modular cover plate with frame and cup washers including one continuous run of PVC insulated (green colour) 1.5 Sqmm multistranded copper conductor cable earth wire and connected to earth dolly complete all as specified and directed one light/one fan/one bell point controlled by one modular switch.

All as per item No.96 herein before but One modular socket outlet 3 pin 6 amps controlled by one switch on same board.

All as per item No.96 herein before but One modular socket outlet 3 pin 6 amps controlled by one switch on independent board.

All as per item No 96 herein before but wiring with 2.5 sqmm copper wire (FR-LSH) PVC and 2.5 sqmm earth wire for modular socket outlet 5 pin 16 amps on independent board.

Supply and fix modular type switch single pole, one way 6 Amp complete all as specified and directed.

Supply and fix socket out let multi 5 pin, 6 Amps, modular type complete all as specified and directed.

Supply and fix switch modular type single pole, one way 16 Amp complete all as specified and directed.

Supply and fix socket out let 2 in1,3 pin, 6 and 16 Amp, modular type complete all as specified and directed.

Supply and fix bell push, 6 Amp 1 module complete all as specified and directed.

Supply & fix ceiling rose, PVC/Poly carbonate, isolated body three terminal complete all as specified and directed.

S & F lamp holder angle type PVC/Poly carbonate type insulated body with back plate suitable for batten/wall fitting complete all as specified and directed.

S & F call bell ding dong AC, 230V single pole complete all as specified and directed,

Supply and fix High quility LED T5 integrated batten tube light 20 Watt with aluminium extrusion with frosted PMMA/PC diffuser, internaly pre wired of 1.5 sqmm twin twisted flexible cable ,Including marking of CA No on batten all as specified & directed. NOTE: The contractor must submit 5 years warranty for LED fitiings.

Supply and fix LED Bulb 9 Watt complete all as specified and directed.

S&F LED luminaire wall bracket type, made in fully cast aluminium body finished with polyurethane paint with nipple having B22 holder incl 05/6 watt LED bulb of Make Mepro Cat part No: AL-135 or equivalent make in Bajaj/Havells complete all as specified and directed. NOTE: The contractor must submit 5 years warranty for LED fitiings.

S&F bed side LED light fitting , 6 watt, with independent switch & G-22 holder and LED lamp complete all as specified and directed. NOTE: The contractor must submit 5 years warranty for LED fitiings.

S & F in repair MCB single pole, 240 volts, 5 to 32 Ampere, rupturing capacity 10 KA, ‘B’ curve type in the MCB DB including taking down complete all as specified and directed.

S & F in repair MCB single pole and neutral, 240 volts, 32 Ampere, rupturing capacity 10 KA, including taking down complete all as specified and directed.

S&F in repair sheet metal enclusure for DBs(double door type) single pole and neutral 8 way including blanking plate as required with 200 Amps rated bus bar, 240 volts fixed complete all as specified and directed .

S&F in repair sheet metal enclosure single pole and neutral with a two pin and earth plug and socket for geyser complete with one single pole MCB 240 Volts 20 Amps incl one 15 Amp switch on existing bd for switching geyser on/off complete all as specified and directed.

M&L for earthing complete with galvanised steel, earth plate electrode 600x600mm x 6mm thick burried directly in ground verticaly (earth pit not less than 2.25 mtrs below ground level ) with top edge of the plate not less than 1.5 mtrs below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron/steel all as shown in electrical plate No 3 on page 497 of MES schedule 2009 part - I connected to main switch board/main DBs/earthing test point including all necessary excavation and earth work in hard/dense soil common salt and charcoal dust mixed and packed 150mm thick all round the GI earth plate, watering pipe 20mm dia GI medium grade. GI sheet 0.63 mm thick funnel, wire gauge, 50mm thick RCC cover in PCC 1:2:4 type B1 duly reinforced with MS round bars 6mm dia @ 150c/c both ways and pit/chamber in PCC 1:3:6 type C1 with suitable lifting handle to cover, GI protection pipe 15mm dia light grade up to 7.5mtr from electrode GI pipe to be fixed with complete all as specified and directed. Note :- (i) Earth lead beyond 7.5 mtr from electrode to earth terminal point/main switch & GI pipe light grade 15mm dia for protection against mechanical damage to lead shall be measured separately. (ii) On testing after completion if desired earth resistance is not obtained, the earthing will be redone at no extra cost.

Supply & Fixing in repair LED bldg security light fitting 35 W/36 W, 230V AC outdoor type with high pressure die cast aluminium IP66 roadway luminaire with high power LED as light source and electronic driver including GI bracket light grade with impact and corrosion resistant including thermal management in multiple optics and provn of electric supply to fitting from source by means of PVC Sheathed multi-stranded aluminium conductor cable complete including taking down existing old light fitting any type all as specified and directed.

S & F LED bulk head fitting, 1 x 10 watt with PDC aluminium housing and milky diffuser including LED light driver holder, complete with all accessories and including connecting up with three core twisted flexible copper conductor cable with suitable size of 230 Volts, 50 Hz complete all as specified and directed.

Supply and fix High quality LED lighting fixture mirror type with high output diffuser 2 feet 1x 10 Watt. 220V AC,complete with polycarbonate tube, white/warm white suitable for mirror light internally pre wired of 1.5 sqmm three core flexible cable complete all as specified & directed

S&F Exhaust fan metallic bady ISI mark, 300 mm size with bladesand frame and louvers including cutting openings, through brick/ stone wall , making of holes and grouting of suitable size of nuts and bolts for 300 mm exhaust fan and making good dismantled portion and making connection with wire of suitable size and connecting accesssories complete all as specified and directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz,RPM 1200, Copper winding of sweep 250mm including cutting openings, through brick/ stone wall , making of holes and grouting of suitable size of nuts and bolts for 250 mm exhaust fan and making good dismantled portion and making connection with wire of suitable size and connecting accesssories complete all as specified and directed.

Taking down storage type water heater (geyser) of any type /make up to 50 Ltr capacity after disconnecting electric / water connections and refixing the same after carrying out necessary repairs including reconnecting the electric / water connections and testing complete all as specified and diected.

S& F socket outlet for TV/Video/audio device modular type with inner and outer modular plate type, specially built for wall/high mounted TV and incl pressed steel/metal flush box concealed complete all as specified and diected

Supply & Fixing of non metallic PVC conduit 25 mm exclusive of boxes but includinf of all tees,bends,elbows, reducers,bell mouth tube ends and fixing accessories such as couplers,lock nuts,saddles, pipe hooks etc. concealed in wall ceiling floor etc for television/DTH/telephone/Data cable complete all as specified and directed.

Supply, installation, testing & comissioning of 1 core 1.5 sqmm FR-LSH copper wire in existing conduit for inverter wiring.(Two Light Points & Two 5A Sockets shall be on inverter) all as specified and directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of of size 10 sq mm 2 core complete all as specified and directed

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m deep for laying of underground cable and getting out in any type of soil complete all as directed by the Engineer-in-Charge

Returning, filling in, including spreading, leveling watering and well ramming in layers n.exc 25 cms. thick in soft / loose soil complete all as specified and directed by Engr -in -charge .

Removal of surplus soil not exceeding 50 Mtr and depositing where directs at a level not exceeding 1.5 Mtr above the starting point complete all as specified and directed by Engr-in-Charge.

M&L for sand cushioning in trenches spreading and consolidation 8cm thick before laying the cable & 15 cm of sand after laying the cable complete all as specified

M&L for laying of bricks well burnt sub class ‘B’ (old pattern) laid flat for cable protection width equal to the lengrth of brick complete all as specified .

M & L galvanised steel water tubing 'light grade' 40 mm bore with all fittings laid under the roads, drains, culverts and fixed on poles etc complete all as specified and directed .

Supply,fix, testing and commissioning of Kitchen exhaust system/ electric chimney, with dry heat clean technology , matt black finish, Hassle free filter less and dry heat auto clean technology, thermostatic touch control with 3 speed gesture motion, with black metal oil collector, motor, black glass clad hood with LED Insignia, Front panel with black glass, energy saving LED light , metal blower + metal housing, designed air flow (max), 1250 Nm3/h, noise level 58 dBA (max), lifetime warranty size 90cm, complete with all civil work for fixing system incl making hole and repairing /replastering the disturbed surface and make good with existing wall paint/colormade The quoted shall include all kind of addition/alteration civil work including plastering, PCC and brick work reqd to install the chimney at the site.complete all as specified and directed

Joshi Constructions (BID ID -3354685)

aditya construction (BID ID -3362757)