Balussery Block Panchayath 2024-25 - Ulliyeri CHC Public Health Unit Renovation and Cabin Construction in Ulliyeri GP (226/25) (183/26)

Partition work

21.1.1.2:Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately): For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

21.1.2.2:For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron)

21.3.1:Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm)

21.2.1:Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS : 12823 Grade I Type II, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer - in- Charge.Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side

14.1.1:Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground within 50 meters lead:With cement mortar 1:4 ( 1 cement : fine sand)

15.13.1:Taking out doors, windows and clerestory window shutters (steel or wood ) including stacking within 50 metres lead:Of area 3 sq. metres and below

9.48.2:Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings/ wooden frames with rawl plugs screws etc

13.61.1:Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work

OD420934/2025-2026:Providing and fixing thermal insulation with synthetic wool conforming to polythene Bags fixed to wall with screw,rawel plug &amp washers and held and in position by criss cossing GI wire etc. complete as per directions of Engineer in charge

OD420988/2025-2026:Veneered MDF slat wall panelling (lower wall) providing and fixing 18mm veneered MDF slats (exterior grade ) of width bet ween4to 5 inch. Same is fixed on 50*50mm wood strip (sal wood ) Horizontally spaced and fixed at every 600mm includinng cost of all labour charges materials conveyance charges cost of hardwares etc complete

OD421016/2025-2026:POP panelling of size 12.5mm having approx.15% perforated area with perforation size and pattern as approved by the Engineer in charge and as per manufacture &39, specification withall 4 side tapered as per direction dept officer at site

OD421187/2025-2026:Fabricating and fixing stainless steel door handle including bending to required shape fixing on the glass panel etc complete

OD421234/2025-2026:supplying and fixing sila phalakam with granite stone of size 900*600mm or nearest on prepeared wall with engraving English or malayalam letters of specified size on hard stone including cost conveyance and labour charges

OD421260/2025-2026:Multi wood panel letters. Providing and fixing letters 15to 30 cm height using multi wood panel 17mm average thickness design as per the departmental approved drawing , including all cost of materials , jigsaw cutting charges, all labour charges, conveyance and machineries etc

13.68.1:French spirit polishing:Two or more coats on new works including a coat of wood filler

9.1.1:Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).Second class teak wood

9.5.1.1:Providing and fixing panelled or panelled and glazed shutters for shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessery screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer - in-charge. Second class teak wood35 mm thick shutters

10.15.1:Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular /L-Type sections, made of 1.60 mm thick M.S. Sheet,joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 ( 1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

11.33.1:25 mm wooden planking, tongued and grooved in flooring, including fixing with iron screws complete with:Second class teak wood

Please Enable Macros to View BoQ information