PROVN OF TOILET BLOCK WITH 6 X WC AND 4 X WASH BASIN AT JOSHIMATH UNDER GE 871 EWS

Amount

Surface excavation n. exc. 30 cm deep and averaging 15 cm deep and getting out in hard/dense soil.

Excavation in trenches in exc 1.5 m wide and not exc 1.5 M depth for foundation and getting out in soft and loose soil.

M&L Cement concrete 1:4 :8 type D2 using (40 mm graded stone aggregate) as in filling, fdn, mass concrete and sub base of floors etc.

Returning, filling in including spreading leveling watering and well ramming in layers not exc 25 cm (soil)

Removing excavation materials not exc 50 Metre and deposition where directed at a level not exc 1.5 M above the starting point (soil).

M&L for RCC M 25 ( design mix using 20mm graded stone aggregate) for lintel beam, roof beam, cantilevers, bressummers etc complete all as specified and directed.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 5cm but n exc 10cm wide all as directed by Engineer-in-Charge.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports over hangs etc.complete all as specified and directed.

M&L for mild steel TMT steel bars in reinforcement 10mm dia and over cut to length bent to shape required including cranking binding spirally, hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for mild steel TMT steel bars in reinforcement 5mm dia and over up to 10mm dia in stirrups cut to length bent to shape required including cranking binding spirally, hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for DPC 40mm thick in cement concrete 1:2:4, type B-0 to horizontal or vertical surfaces including necessary formwork complete all as specified and directed.

M&L for precast cement concrete 1:3:6 type C1 using 20mm graded aggregate as in solid building blocks, exc. 10cm in width and setting in CM (1:6) complete all as specified and directed.

M&L for precast cement concrete 1:3:6 type C1 using 20mm graded stone aggregate as in solid building blocks, 10cm in thick and setting in CM (1:4) complete all as specified and directed.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces with CM 1:6 finished even and smooth without using extra cement.

M&L for rendering 15mm thick on other than fair faces of brick work or concrete surfaces with CM (1:4) finished even and smooth without using extra cement complete all as specified and directed.

M & L hard core of broken bricks gauge n. exc 63 mm, deposited spreaded and leveled in layer not exc 15 cm thick, watered and rammed to a true surface, broken stone or boulder.

M&L PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate) as in surface channel and drain and manhole etc, complete all as specified.

M&L PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate) 75 mm thick as in plinth protection complete all as specified and directed.

M&L PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) 100mm thick as in sub base complete all as specified and directed.

M&L for Non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.11 sqm but n.exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and incl over screed bed or bedding layer of cement mortar 15mm thick for laying tiles in cement mortar 1:6 complete all as directed.

M&L for Glazed ceramic coloured tiles of size 300x450x7mm/350x450x7mm thick over and incl 10mm thick rendering in cement mortar 1:4 as in backing coat for tiles on vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as directed.

M&L Steel work in tubular trusses/pillars/braces etc including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 all as specified and directed by Engr-in-Charge.

M&L Mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment as in Base plate/Gusset plate, cleats for securing purlins/rafters and similar articles conforming to Fe 290 (Gde E 165) all as directed by Engr-in-Charge.

M&L Mild steel screw bolts (machine made) 16mm dia with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 30cm long all as specified and directed by Engr-in-Charge.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of approved colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

S&F Mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as directed by Engineer-in-Charge

M&L Mild steel framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 all as directed by Engr-in-Charge.

S&F for 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed

S&F for Solid PVC door frame of size 50 mm x 47 mm, made out or 5 mm, plain colour PVC sheet, reinforced with MS Square tube all as specified and directed.

S&F for Factory made solid panel PVC door shutter, 30 mm thick (Style) consisting of frame made out of M.S. tubes for top and bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel on both sides having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on both sides and as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement and fixing in the frame at site all as per specification & drawing all as specified and as directed.

S&F for butt hinges medium weight cold rolled mild steel 100 mm complete all as specified.

S&F for Aluminium anodised barrel tower bolt, of extruded section and fixed of 125 mm long complete all as specified and directed.

S&F for extruded aluminium alloy handles fabricated type, anodised 125 mm long all as specified and directed

S&F for 300 mm long aluminium alloy, anodized, sliding door bolt with hasp, staple(bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

M&L for preparation of new wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of approved colour synthetic enamel paint over a coat of pink primer all as specified and as directed.

M&L preparation new steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

S&F for steel ventilator with top hung shutter including hinges, steel peg stay complete all as specified and directed

M&L for preparing new plaster surface and apply two coat of oil bound distemper over a coat of wall care putty to obtained smoothness of wall surfaces over one coat of primer complete all as specified and directed.

M&L for preparing new plaster surface of walls and apply two coat of Cement based paint over one coat of alkali resistant primer complete all as specified and directed.

S&F 15 mm bore GI tubing medium grade with all fitting fixed to wall and ceiling or laid in floor complete all as specified and directed

All as per item no. 40 above but 20 mm bore complete all as specified and directed.

S&F 75 mm dia PVC (SWR) pipes single socketed fixed in walls and floors or trenches etc. complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipe single socketed any length with rubber ring joints laid in trenches all as specified and directed.

S&F PVC (SWR) bends any radius 110mm bore pipe complete all as specified.

All as per Srl item No. 44 here in before but 75 mm all as specified.

S&F PVC (SWR) branch piece, single (single Y) equal or unequal of 75 mm complete all as specified and directed

S&F PVC (SWR) 75 mm single junction T equal or unequal complete all as specified and directed

S&F PVC (SWR) 100 mm single junction T equal or unequal complete all as specified and directed

M&L for 75mm PVC(SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F vitreous China wash down water closet pan (pedestal pattern), white with trap incl connection to outgoing pipe and flushing pipe, anti syphonage pipe etc complete including provision of lime concrete bedding complete all as specified and directed.

S&F vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) complete including provision of lime concrete bedding complete all as specified and directed.

S&F Vitreous china wash hand basin oval shape granite top white flat back including brackets and 32 mm dia bore waste fittings brass chromium plated for glazed ware sink, basin etc with long screwed shank and fly nut , flange and bedded in red lead cement and other end fixed incl waste pipe of reqd length complete all as specified and as directed by Engineer-in-Charge and approved by GE.

S&F 15mm bore pillar tap suitable for oval shaped granite top wash hand basin cast copper alloy with capstan head, fancy type chromium plated screwed down high pressure with or without lettered 'Hot or 'cold' with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as Engineer-in-Charge and approved by GE.

S&F Flushing cistern low level, PVC 10 Ltr capacity symphonic action type valve, valve less with inlet ball valve, float and handle incl bracket complete all as specified and directed.

S&F Flush pipe of polythene of low or high density or PVC, 32 mm dia for low level cistern complete all as specified and directed.

Supply and fix for PVC(LDPE), 32 mm dia, polyethylene, of pressure rating 6 kgf/sqcm, fixed complete to wall, ceiling or in floor, for wash hand basin all as specified and as directed.

S&F PVC connection 15 mm dia and 450 mm long complete all as specified and as directed.

S&F CP grating of size 100 mm dia with waste hole complete all as specified

Supply and fix for towel Rail, brass chromium plated. 20 mm dia D type, 600 mm long between flanges complete all as specified and as directed

Supply and fix Sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with mild steel chromium plated bracket guard and railing 60cm long complete all as specified and as directed.

S&F soap dish acrylic type complete all as specified

S&F 15mm dia angle valve cast copper alloy, chromium plated, fancy type screwed down high pressure, with crutch or butterfly handle screwed with both ends for iron pipe or for union complete all as specified and directed.

S&F 15mm dia Bib taps, cast copper alloy, chromium plated fancy type, screwed down high pressure, with crutch or butterfly handle screwed with both ends for iron pipe or for brass ferrules and complete all as specified and directed.

S&F sheet glass 3 mm thick of ordinary quality and glazing with oil putty in square n. Exc.0.5 sqm in each pan

S&F 12mm thick perforated particle board for insulation and acoustic purposes, 60x60cm fixed with screws on ceiling flat/sloping to aluminium snap grid of size 605x605mm grid incl complete hanging arrangement reqd at site all as directed by Engineer-in-Charge

M&L for precast manhole covers in precast cement concrete Type B-1,1:2:4 (using 20mm graded crushed stone aggregates) set in cm 1:6.

S&F Jet spray CP with all necessary fittings all as directed by Engineer-in-Charge.

S&F Plastic water closet seat cover for pedestal pan with flat bottom and cover and mild steel chromium plated with all necessary fittings all as directed by Engineer-in-Charge.

Cutting into existing manholes for connecting new drains, making good to pipe internal dia 100mm and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required as directed by Engineer-in-Charge

M&L for chequered cement concrete tiles of size 30cm X 30cm X 25mm thick, set and jointed and pointed in neat cement slurry in floors with grey cement and pigments over 15 mm thick screed bed in CM 1:4 complete all as specified and directed.

M&L Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete over screed bed or bedding layer of cement mortar 15mm thick in cement mortar 1:6 complete all as directed.

Rounding to edges of granite stone slabs on edges such as in steps, cooking platform and other similar work and polishing complete all as directed by Engineer-in-Charge.

Supply and fix for Gun metal gate valve,20 mm bore, cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions all as specified and as directed.

Supply and fix rotational moulded polyethylene water storage tanks ISI marked of 1000 litre capacity (Cylindrical vertical with closed top) with HD polythene float (ball) and epoxy coated aluminium rod (fly nut) screwed for iron pipe or brass ferrule hoisted and fixed in position all as specified in SSR Part-I ,complete all as specified and as directed.

M&L for PCC 1:3:6 type C2 Concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested; complete all as specified and directed.

S&F for 150 mm bore Reinforced concrete pipes, class NP2, laid and jointed complete with collars

M&L for point wiring concealed type with 1.50sqmm PVC FRLS insulated, unsheathed, single core, multistranded copper conductor cable 1100 volts grade including 1.5sqmm FRLS PVC insulated unsheathed stranded copper conductor cable as earth continuity conductor drawn in and including rigid PVC conduit of suitable size but not less than 20mm dia size confirming to IS 2079-1973 medium grade with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodised steel box painted with one coat of red oxide primer,all fittings such as elbows, bends, junction boxes, saddles including PVC board (ISI Mark) and screws and rawal plugs including 3.0mm thick ISI marked plastic laminated sheet cover for fixing switches/ socket/regulators etc including cutting chases in wall as per standard engineering practice & making good the disturbed surfaces to match with existing for the following complete all as specified & directed.

(a) One light/fan/bell point controlled by one ,one way switch 5/6 Amps.

(b) One socket outlet 5 pin 5/6 Amps on independent board controlled by one, one way switch.

(c) One socket outlet 5 pin 5/6 Amps on same board with other one, one way switch.

All as per item No 78 above but for socket out let, 15/16 Amps on independent board with 4 Sqmm size cable and 2.5 Sqmm for continuity earth wire connected to common earth dolly all as specified and directed by Engr - in - charge.

S&F switch piano flush type 5/6 Amps single pole one way all as specified & directed.

S&F switch piano flush type 15/16 Amps single pole one way all as specified & directed.

S & F socket out let 5 pin 5/6 Amps all as specified and directed.

S&F socket out let 2-in-1, 6 pin 5/6 & 15/16 Amps all as specified and directed.

S&F ceiling rose 2/3 terminals 65x25 mm dia poly carbonate isolated all as specified & directed.

S&F LED tube light fitting two feet 10 watt, slim design, 230volts, including connected with 3 core 23/0.0076 insulated copper wire from ceiling rose to fitting connector all as specified and directed.

S&F LED tube light fitting bright 18 watt. slim elegant design. and including connected with 3 core 23/0.0076 insulated copper wire from ceiling rose to fitting connector all as specified and directed.

S&F building security light fitting complete with 25 watt LED type pressure die cast aluminium housing and heat resistant toughened glass with frame protection and better optics for uniform distribution complete fixed bracket made out of GI pipe 32 mm dia (light grade) 1.5 metre long and MS clamp and nut bolts washers and connected with twin core cable 1.5 sqmm from ceiling rose to fittings connector all as specified and directed

S & F exhaust fan AC single phase 230/240, 50 HZ Volt of size 300 mm sweep 900 RPM MS body heavy duty operating with louvers shutter complete grouting the ragged bolt in wall fixing the frame and exhaust fan fix including louver shutter with frame on the exhaust side and connecting with PVC insulator 3 core 23/0.0076 copper wire rubber insulated from ceiling rose to exhaust fan motor complete all as specified and as directed

Supply and fix of DB, SPN 8 way double door for MCB, 240 volt with 200 amps rated bus bar with enclosure blank plates for unused all as specified and directed

Supply and fix MCB 6-40 amps, 10 KA, SP 240 volt, 'C' series all as specified and directed

Supply and fix MCB 40 amps, 10 KA, DP 240 volt, 'C' series all as specified and directed

M&L in earthing complete with galvanised steel earth plate electrode size 600X600X6mm thick burried directly in ground vertically to a depth not less than 2.25m deep below normal ground level with top edge of earth plate not less than 1.5m deep below normal ground level and connected to and including GI earth lead wire 4mm dia by means of bolts, nuts, check nuts & washers of galvanised iron and connected to test point all as shown in electrical plate No 3 of SSR part I-2009 and all as specified or indicated and testing on completion including excavation and earth work in any type of strata available at site, PCC (1:3:6) type C-1 earthing chamber, pre cast RCC slab 50 mm thick in cement concrete (1:2:4) type B-1 using 20 mm graded crushed stone aggregate reinforced with welded steel wire fabric (XPM) weight not less than 4 kg/sqm funnel with GI watering pipe of 20 mm bore medium grade, wire mesh and lugs, GI protection pipe of 15 mm bore light grade up to 7.5 metre long all as specified and directed. NOTE :- 1. GI earth wire and protection pipe beyond 7.5 metre will be measured and paid separately. 2. If the desired earth resistance is not found earthing shall be re-done by the Contractor at no extra cost paid by Dept.

Excavation in trenches n. exc. 1.5 mtr in wide and n. exc. 1.5 mtr in depth for laying of underground cable and getting out in hard/dense soil complete all as specified and directed.

M&L local sand dry, filling in trenches around under ground cable complete all as specified and directed.

M&L for providing of new sub class 'B' bricks, old size, well burnt laid flat dry for protection of under ground cable complete all as specified and directed.

Supply laying and testing cable XLPE insulated screened PVC bedded galvanized steel strip or wire armoured electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 10 sqmm 2 core complete all as specified and directed.

Supply laying and testing cable XLPE insulated screened PVC bedded galvanized steel strip or wire armoured electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 16 sqmm 4 core complete all as specified and directed.

Supply and fix of GI tubes light grade, galvanised, 32 mm bore including necessary GI fittings, laid in trenches or under floor or fixed with poles/walls for fixing of air termination complete all as specified and directed.

M&L for earthing complete with using galvanized mild steel earth plate (electrode) 600 mm x 600 mm x 6.30 mm thick buried directly in ground, earth pit not less than 2.25 mtr deep below ground level with top edge of the earth plate not less than 1.50 m below ground level and earth plate surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all round the plate using 32X6 mm GI earth strip as earth lead moulded and riveted to earth plate at one end and connected to main equipment at switch/control board at another end, GI earth lead incased in and including 50 mm dia GI ‘light grade’ pipe from upper end of earth plate upto equipment with & including 20 mm dia bore GI pipe ‘light grade’ as water pipe from earth chamber to upper edge of the earth plate, GI funnel with wire mesh fixed on water pipe and provision of PCC 1:2:4 type B1(using 20 mm graded stone agg) as in pits chamber and RCC pit cover 50 mm thick of precast RCC 1:2:4 type B-1 (using 20 mm graded stone agg)duly reinforced with mild steel round bars 6 mm dia @ 150 mm c/c both ways with 10 mm dia mild steel bars as in lifting handles with and including necessary excavation & earth work including laying the GI pipe concealed in floor /wall all as per plate No. 3 of SSR Part I complete all as specified and directed and testing on completion. NOTE :- 1. GI earth wire and protection pipe beyond 7.5 mtr will be measured and paid separately. 2. If the desired earth resistance is not found earthing shall be re-done by the Contractor at no extra cost paid by Dept.

Supply, fix, testing & commissioning for Outdoor Bus bar box size 450 x 350 x 250 mm fabricated out of 2 mm thick MS Sheet having 4 Nos closed Aluminium bus bar chamber of capacity 200 A (including necessary insulator) suitable for 3 phase & neutral, 4 wire 50 Hz AC,415V including red, blue & yellow LED indication lamp and front openable hinged cover with proper locking arrangement, outdoor type weather proof with angle iron of size 40x40x4 mm (including painting of angle iron) outer, floor mounting 60 cm above ground level grouting including making PCC 1:2:4 type B-1 using 20 mm graded coarse aggregate block of size 500x400x300 mm with complete plastering & white wash etc also includes provision of suitable size of cable glands, cable lugs, nut, bolts, washers etc for fixing of cable with the bus bar. The bottom portion of enclosure shall be minimum 45 cm above ground level of legs of angle iron all as specified and directed.

Supply and fix of GI tubes medium grade, galvanised, 20 mm bore including necessary GI fittings, laid in trenches or under floor or fixed with poles/walls for fixing of air termination complete all as specified and directed.

SIDHARTH CONSTRUCTION

ms triveni nirman

M/S RAMESH LAL