PROVN OF HARD STANDING AND CERTAIN OTHER SANCTIONED WORKS AT PALAMPUR MIL STN

Amount

M&L surface excavation not exc 30cm deep and averaging 15cm deep & getting out in soft/loose soil complete all as specified and directed.

M&L 100mm thick hardcore of gauge not exc 63cm, deposited, spread and levelled in layers not exc 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L 75mm thick PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in sub base etc and finished the surface even and smooth without using extra cement complete all as specified and directed.

Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in foothpath, parkds, lawns, drive ways or light traffic parking etc of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed or coarse sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete and including demolition of existing tiles and removal outside the MoD land complete all as specified and directed.

Excavation over areas not exc 1.5m deep in any type of soil & getting out complete all as specified and directed.

Brick work with fly ash bricks, straight or curved on plan exceeding 6m mean radius with fly ash bricks, built in CM 1:4 complete all as specified and directed.

M&L PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in foundation filling and mass concrete complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc25 cm any type of soil complete all as specified and directed.

Removing excavated soil n exc.50m and depositing where directed at aleveln exc 1.50m above the sterting point complete all as specified and directed.

Excavation post holes (or similar holes) in any type of soil each n exc 0.50 cu.m,getting out,returning,filling on and ramming earth or broken rubble mixed with earth around,in layers not exceeding 25cm watering and removing surplus soil to a distance not exc 50m and making good surface complete all as specified and directed.

Excavation in trenches,nexc 1.50m wide and n exc 1.50m in depth for foundation,etc or for shafts,wells,cesspits,manholes,pier holes,etc n exc 10 sq m on plan and getting out any type of soil complete all as specified and directed.

M&L PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in sub base complete all as specified and directed.

S&F hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting etc. and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

S&F framed work as in doors or gates of angle or other section with gusset plates,rails, braces, etc., complete,drilling for fixing of steel sheeting or other covering. doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering,running rail and guides) and hanging;also fastening and fixing conform to Fe-290 Gde E-165 complete all as specified & directed.

M&L preparing new surface of steel of any description, over 10cm width or girth not other wise described and appliying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer, complete all as specified and directed.

Supply only chain link MS galvanised fencing, any size or type (100x100mm, 3mm dia) complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts. etc including provision of binding wire complete all as specified and directed.

S&F mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L rendering 15mm thick plaster in CM 1:4 on fair faces of brick/concrete surfaces finished the surface even and smooth without using extra cement mixed with WPC @ 3% by Wt. of cement (external surfaces) complete all as specified and directed. Note: WPC shall be measured and paid separately.

Mild steel screw bolts not exc 12mm dia of neck (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, not exc 5cm long complete all as specified and directed.

S&F rolled mild steel sections like angle, channel, flat etc as inframed work such as grills, gratings,etc,with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars; barred iron doors; ladders ; framed balusters; walk ways; railings; framed work of water tanks and similar work confirming toFe-290Gde E-165 complete all as specified & directed by Engineer-in-charge.

M&L plain cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate cast in situ in lintels up to 1.5 m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings up to 60 cm in height, copings, kneelers, apex stones, bed plates, water through and the like including weathering, slightly rounded or chamfered angles and throating including use of form work (straight or curved) complete all as specified & directed.

M&L prepartion of newly plastered wall surface and applying two coat of white wash complete all as specified and directed.

M&L brick work with sub class 'B' bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed.

M&L 75mm thick PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in sub base etc and finished the surface even and smooth without using extra cement complete all as specified and directed.

M&L 50mm thick PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in plinth protection/flooring finished the surface even and smooth without using extra cement complete all as specified and directed.

M&L broken stone or boulder hardcore of gauge not exc 63mm, deposited, spread and levelled in layer not exc 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L 38mm glass dividing strips, 3mm thick, inserted in position, confirm to design complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not other wise provided for complete all as specified and directed.

Demolition of brickwork or stone/boulder masonry built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facing, dressed stone work precast concrete articles complete all as specified and directed.

S&F mild steel TMT bars 6 to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L RCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in foundation, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under reamed piles and mass concrete complete all as specified and directed .

M&L RCC (nominal mix) 1:2:4 type B1 (using 20mm thick graded stone aggregate) as in column, pillar, pier posts and struts complete all as specified and directed.

S&F mild steel 0.80mm thick, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched, including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams, including bending or turning up, mitred angles etc as required complete all as specified and directed.

M&L formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter in rough finishes of surfaces of concrete including fair finishes complete all as specified

Formwork to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed.

Rendering 5mm thick plaster in CM 1:3 on fair faces of brick /concrete surfaces finished the surface even and smooth without using extra cement complete all as specified and directed.

M&L preparation of newly plastered wall surface and applying two coats of cement base paint complete all as specified and directed.

Supply and installation of 16 mtr high mast light in two section suitable for 55 m/sec wind speed along with head frame luminaire carriafe suitable for 08 luminaires in symmtricals arrngement and other accessories manufactured in factory witth riasing lowering system comparising double drum winch 5mm diameter SS wire rope , trailing cable , connector , intergal power tool motor , manual handle , junction box lightening finial (wiring material from JB to individual luminare and MCB in base compartment are not included and are a part of installation ) with supply of foundation bolts manufactured from special steel along with nuts, washers , anchor plate and common template and outdoor stand mounted feeder pillar with 32A TPN MCB incomer , single dial time switch 25 A TP contactor and raise lower push button incoming 35 Sqm mm and out goining 16 & 2.5 Sqmm terminals , 16 mtr High Mast of Bajaj Make or equivelent in GE Crompton , Philips , Havells comprising following :-

HIGH MAST SYSTEM Make Bajaj Electrical Ltd,Height of mast : 16 Meter , No of Section - Two , Material Construction : S355 Grade as per BS EN 10025, Base dia and top diameter (A/F) : Top 150mm, Bottom - 460MM, Cross section of mast - 20 side polygon, Standard for Galvanisation - As per BS EN ISO 1461, Size of Opening and door at base - 1200 x 250mm, Diameter of base plate - 670mm , Thickness of base plate -25mm, Lightening protection finial - GI single spike of length 1200mm, Max wind speed - 44m/s as per IS 875 (Part III) , Number of foundation bolts - 12 Nos, PCD of foundation bolts - 590mm, Type /diameter /length of foundation bolts - TS 600/30mm dia/850 mm long FOUNDATION DETAILS Excavation- 2800x2800x1500mm size, Lean Concrete 100 mm thick (1:4:8) D2 using 40mm graded aggregate, Matt bars 12 mm TMT bars @ 200C/C both ways in double layers, RCC(1:1.5:3) 2600x2600x300mm as in footing. RCC (1:1.5:3) 1000x1000x1400MM(1100 below GL and 300mm above GL) . 8 Nos 16mm dia TMT bars at corners 4 at centres of pedestal col as main bar with 600mm long craking at bottom over matt bars . 16Nos 12mm dia TMT main bars (4 Nos each at 4 side with 600mm long cranking at bottom over matt bars. 10mm dia TMT bars @ 150mm C/C as stirrups. 300mm dia 850mm long foundation bolts 08 Nos inserted in to 16mm thick anchoring plate 590mm dia at bottom with pointed galvanised nut one each at bottom and top of plate. Foundation bolt min clearance 150mm above at bottom of base plate 2 Nos at top of base plate. Note- The unit rate is inclusive of necessary formwork , RFR removal of surplus earth external finishes and other unforseen items all as directed by Engr -in -charge LUMINARIES CARRIAGE Material of construction - 50NB ERW class BMS Pipe . Diameter of carriage ring (mm) - 535 mm (ID) . Construction -06 Arm welded , 2 sections. Load carrying capacity - 08 Luminairs TRAILING CABLE : Conductor - Copper 5 Core 2.5 Sqmm. Insulation - EPR insulated PCP scheathed . Nos of circuit per mast - One WINCH /POWDER TOOL Type SWL of winch - Double drum , SWL 750 kg SGDD. Method of operation - Intergral motor. Motor capacity - 1.0HP (including suitable starter). No of speeds - 6 Pole single speed. Torque Limitor - With Mechanical Tripping Facility. STAINLESS STEEL WIRE ROPE Grade /construction - AISI 316,7/19 Construction. Numbers of Ropes - Two Continuous. Diameter(mm) - 6mm. Breaking Load capacity - 2350 Kg x2

S&F 200W LED flood light matt black polyster powder coated with secondary lens optics with LED make lumiled having luminaire efficiency of 130lm/W Total of 26000 Lums+/- 10% Provided with built in surge protection 5KV and external surge protection of 10kv having Ingress protection lp66 complete all as specified and directed.

S&F testing of Aviation obstruction light red painted housing , Red coloured Polycarbonate dome and accessories complete all as specified and directed by Engr in Charge (01 Fitting required per High mast)

Supply,install,testing and commissioning of CPRI approved factory made LT feeder piller box outdoor type with double doors provided with locking arrangements dust, vermin and water proof made out of 3.15 mm thick CRCA sheet duly compartmentalized inside panel with 2mm thick CRCA sheet powder coated with back door detachable fixed with nuts, bolts and washers and front doors openable type fitted with hinges and knobs/locks. Panel is to be placed on angle (size 50x50x6mm) frame duly painted with two coats of synthetic enamel paint over a coat of primer to the portion visible to eye supported on 04 legs 750mm long each duly 450 mm grouted in PCC blocks of type 1:2:4 type B-1and 300mm above ground level for entry of cables suitable for 3-phase, 4-wire, 50Hz,415 volts,with and including necessary incoming and out going cable connection with proper size aluminium lugs, nut bolts etc including the folowing complete all as specified and as directed:- (a) MCCB 63A,4P, 415V, 25KA - 01 Nos (b) Power contactor 3 pole AC 70Amps 50Hz ML type (Make - L&T cat part No SS90910 Model ML-4 -01 Nos (e) LED type AC 220V Phase Indicators RYB, with toggle switches -01 Set (f ] PVC type sleeves 400 Amps capacity TPN mounted on epoxy insulators - 02Set Voltmeter, Amper meter, CT coil 100/5-01 set. (v) Aluminium Bus bar 4 strip -of suitable capacity. (vi)Internal wiring of panel board with copper cable single core of sutable size and incl 03 Nos bakelite control fuses. [g] Danger notice plate for LT with conventional skull and bones duly rivetted/pasted to the panel board door Note :- The contractor will approved the panel drawing before incorporate in the work and should be CPRI approved

Supply and laying or fixing or passing through pipe or laid in trenches, 1100 Volt grade heavy duty cable XLPE insulated, armoured electric cable with aluminium conductor ,cross-sectional area 35 sq.mm 3.5 core including taking out old unserviceable cable complete all as directed by Engineer-in-charge.

Supply and laying or fixing or passing through pipe or laid in trenches, 1100 Volt grade heavy duty cable XLPE insulated, armoured electric cable with aluminium conductor ,cross-sectional area 16 Sq.mm 2core including taking out old unserviceable cable complete all as directed by Engineer-in-charge.

M&L PCC 1:2:4 type B2 (using 40mm graded crushed stone aggregate) as in foundations filling and mass concrete complete all as specified and directed.

M&L RCC (nominal mix) 1:2:4 type B0 (using 12.50mm thick graded stone aggregate) as in column, pillar, pier posts and struts complete all as specified and directed.

M&L for sand cushioning to under ground cables 8 cm thick before laying the cable and 15 cm, thick after laying, stretching and testing the cable complete all as specified and directed by Engr-in-Charge.

M&L for laying in trenches burnt brick sub class 'B' for cable protection laid adjacent to each other length wise perpendicular to the central axis of cable complete all as specified.

M&L Earthing complete with galvanised steel earth plate electrode 60cm ×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion

M&L Earthing complete with galvanised steel earth plate electrode 60cm×60cm.×6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead GI strip 32 x 2 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion

M/S MALHI CONSTRUCTIONS (BID ID -3401822)

BHARDWAJ BUILDERS (BID ID -3395009)