Construction Work of Bus Station Development at Gangajaliya Lake, Bhavnagar.

Name of Work :- Construction of Bus station Development at Gangajaliya Lake, Bhavnagar

estimated Tendered Rates

Item according to

but may be Item of work Unit

less in figures In Words quantities

Excavation for foundation upto 1.5 m depth Rupees One

including sorting out and stacking of useful Hundred Twenty

materials and disposing off the excavated stuff upto Five and Paise

50 Meter lead.(A) Loose or soft soil Eighty Six Only

Excavation for foundation for depth from 1.5 m to Rupees One

3.0 m including sorting out and stacking of useful Hundred Thirty

materials and disposing off the excavated stuff upto Eight and Paise

50 Meter lead.(A) Loose or soft soil Five Only

Boring holes 2.0 m deep in ordinary soil (for cast in Rupees Eight

situ piles) and getting out the soil and disposal of the Hundred Thirty

surplus excavated soil as directed within a lead of 50 Seven and Paise

Providing and laying cement concrete 1:2:4 (1- Rupees Three

Cement : 2- Coarse sand : 4- graded stone Thousand Eight

4 137.26 aggregates 20 mm nominal size) and curing complete Cum. 3824.10 Hundred Twenty

excluding cost of formwork in (A) Foundation and Four and Paise

Plinth Ten Only

Providing and laying controlled cement concrete

M250 work with curing etc. complete including the

5 26.00 cost of from workbut excluding cost of Cum. 4968.75

Eight and Paise

Reinforcement for RCC work in (A) Foundation

footing base of columns and mass concrete.

Boring holes 3.5 m deep in ordinary soil (for cast in Rupees Eight

situ piles) and getting out the soil and disposal of the Hundred Thirty

surplus excavated soil as directed within a lead of 50 Seven and Paise

Providing and laying controlled cement concrete Rupees Four

M.250 and curing complete excluding the cost of Thousand Four

7 10.00 formwork and reinforcement for reinforced concrete Cum. 4411.52 Hundred Eleven

work in (A) Foundations, footings, Base of columns and Paise Fifty

and Mass concrete.(For Auger pile) Two Only

Providing and laying controlled cement concrete Rupees Seven

M250 work with curing etc. complete including the Thousand Six

8 22.00 cost of from workbut excluding cost of Cum. 7612.43 Hundred Twelve

Reinforcement for RCC work in Column upto Plinth and Paise Forty

Level. Three Only

Providing and laying controlled cement concrete

M250 work with curing etc. complete including the

9 47.00 Cum. 6525.08 Hundred Twenty

cost of from work but excluding cost of

Reinforcement for RCC work in Beam. .GB/PB

estimated Tendered Rates

Item according to

but may be Item of work Unit

less in figures In Words quantities

Providing and laying controlled cement concrete

M250 work with curing etc. complete including the

10 3.00 cost of from workbut excluding cost of 0.00 6893.87

Three and Paise

Reinforcement for RCC work in RCC Wall upto Plinth

Brick work using common burnt clay building bricks

having crushing strength not less than 35 kg./Sq.Cm.

11 137.00 Cum. 4279.98 Hundred Seventy

in foundation and plinth in Cement Mortar 1:6 (1-

Cement : 6 -fine sand)(B) Conventional

Ninety Eight Only

Filling available excavated earth (excluding rock) Rupees One

in trenches. plinth, sides of foundations etc. in Hundred Thirty

layers not exceeding 20 cm. in depth consolidating Seven and Paise

each disposited layer by ramming and watering. Forty Seven Only

Filling in foundation and plinth with murrum or

13 451.95 selected soil in layers of 20cm. thickness including Cum. 304.60

and Paise Sixty

watering, ramming and consolidating etc. complete.

Applying general insecticide pest control treatment

to floors, cupboards etc including labour material

etc. complete. Using Imidacloprid 30.5 SCas Per IS

14 96.00 Sqm. 40.02 and Paise Two

part -II( (0.075% concentration by mass) is

recommended 1.5ml chemical diluted with 5 liters of

water application 0.65 litre chemical /Sqm of surface

is recommended as per I.S.

Providing and laying controlled cement concrete

M250 work with curing etc. complete including the

15 4.00 Cmt 7612.43 Hundred Twelve

cost of from work but excluding cost of

and Paise Forty

Reinforcement for RCC work in Column (G.F.)

Providing and laying controlled cement concrete

M.250 work with curing etc. complete including the

16 0.99 Cmt 7654.20 Hundred Fifty

cost of formwork but excluding the cost of

reinforcement for RCC work in Column (F.F.)

Providing and laying controlled cement concrete

M250 work with curing etc. complete including the

17 12.00 Cmt 6498.05 Hundred Ninety

cost of from workbut excluding cost of

Eight and Paise

Reinforcement for RCC work in Lintel/Coping (G.F.)

Providing and laying controlled cement concrete

M250 work with curing etc. complete including the

18 4.00 Cmt 6539.82 Hundred Thirty

cost of from workbut excluding cost of

Reinforcement for RCC work in Lintel/Coping (F.F.)

Eighty Two Only

estimated Tendered Rates

Item according to

but may be Item of work Unit

less in figures In Words quantities

Providing and laying controlled cement concrete

M250 work with curing etc. complete including the

19 10.00 Cmt 6989.95 Hundred Eighty

cost of from workbut excluding cost of

Reinforcement for RCC work in Beam (G.F.)

Ninety Five Only

Providing and laying controlled cement concrete

M250 work with curing etc. complete including the

20 18.00 Cmt 6592.13 Hundred Ninety

cost of from workbut excluding cost of

Reinforcement for RCC work in SLAB (G.F.)

Providing TMT Bar FE 500D reinforcement for R.C.C.

Seven and Paise

21 28971.00 work including Cutting, bending, binding and placing Kg. 77.29

in position complete upto floor two level (G.F.)

Providing TMT Bar FE 500D reinforcement for R.C.C. Rupees Seventy

22 648.00 work including Cutting, bending, binding and placing Kg. 78.36 Eight and Paise

in position complete upto floor two level (F.F.) Thirty Six Only

Brick work using common burnt clay building bricks Rupees Four

having crushing strength not less than 35 Kg/ Sq.Cm. Thousand Five

23 30.00 In Super Structure above plinth level up to floor two Cum. 4568.40 Hundred Sixty

level in cement mortar 1:6 (1 Cement: 6-Fine sand) Eight and Paise

with curing etc. (b)Conventional. (G.F.) Forty Only

Brick work using common burnt clay Building bricks Rupees Four

having crushing strength not less than 35 Kg/ Sq.Cm. Thousand Six

24 6.00 In Super Structure above plinth level up to floor two Cum. 4611.18 Hundred Eleven

level in cement mortar 1:6 (1 Cement: 6-Fine sand) and Paise

with curing etc. (b)Conventional. for F.F. Eighteen Only

Half brick masonry in common brunt clay building Rupees Six

bricks having crushing strength not less than 35 Hundred Forty

25 21.00 Kg/Sq.Cm. in Cement mortar 1:4 (1- Cement : 4 - Sqm. 640.77 and Paise

coarse sand ) in foundation and plinth (B) Seventy Seven

Conventional (upto 10 ton) (for GF) Only

Providing and fixing rolling shutters of approved

make made of 80 mm wide M.S. laths inter-locked

together through their entire length and jointed

together at the ends by end locks mounted on

specially designed pipe shaft with bracket

26 35.70 Sqm. 4546.01 Hundred Forty

plates,guide channels and arragements for inside

and outside locking with push-pull operation

including the cost of hood cover and spring etc.

complete. (B) Shutters having width 3.5 M. and

estimated Tendered Rates

Item according to

but may be Item of work Unit

less in figures In Words quantities

Providing & fixing 35mm.th. Flush Door Solid Double

Core type Both Face water proof Ply Vennered &

mm th.laminate shall be pasted on both side with

adhesives as specified by the manufacturers. The

laminate shall be as per approved shade & texture,

27 10.00 Sqm. 3146.54 Hundred Forty

of make incl.. S.S. Hinges with nessary screws &

S.S.fixtures & fastenings like handle(10 cm),

Fifty Four Only

aldrop(30 cms), stoppers(20 cms) For all Floor etc as

per architectural detailed drawing and as directed by

engineer in charge.

Providing and fixing FRP frame size 100x50 mm and

28mm thick FRP depress panel shutter having extra

reinforcement on sides & edges in Gel coat finish.

The core of the shutter & frame is to be filed up with

injected fire retardant grade polyurethene foam

done in situ alongwith embedded wooden pieces for

28 12.00 Sqm. 2377.76 Hundred Seventy

stiffening & also taking hinges & fintures. The whole

Seven and Paise

FRP frame & shutter is to be water proof weather

Seventy Six Only

proof, termite proof & resistance to mild acid/alkali.

Rates are to be inclusive of S.S hinges with necessary

screws & alluminium fixtures & fastenings & fastener

Providing and fixing window having extruded

aluminum Colour anodized section frame main outer

size 95mm x 24mm x 1.17mm @ wt.of 0.738 Kg/mt

horizontal Three track member size 92mm x

31.75mm x 1.30mm,@ Wt.1.07 Kg/mt , vertical

member of size 92mm x 31.75mm x 1.50mm @ Wt.

1.06 Kg/mt with sliding shutters of horizontal

29 16.00 Sqm. 1583.95 Hundred Eighty

member size 40 mmx18mm x1.29mm @ wt.of

Three and Paise

Kg/mt, vertical member of size 40mm x 18mm x

Ninety Five Only

mm @ wt.of 0.456Kg/mt/ with 5 mm thick

transparent bronze colour tinted float glass with

powder coated aluminum fittings and fixtures and

transparent silicon sealant glass fixing to frame as

per details etc

Providing and fixing standared extruded of Rupees One

alluminium section of size 63mm x 38.10mm x Thousand One

30 6.00 1.2mm @ Wt. 0.643 Kg/mt with colour anodized Sqm. 1175.56 Hundred Seventy

alluminium frame for ventilation with 5 mm thick Five and Paise

frosted glass as details etc complete for Ventilation Fifty Six Only

Providing and fixing M.S. grills of required pattern to

marble/granite frames of window etc. with M.s. flats

at required spacing and frames alround, square or Rupees One

round bars fixed with round headed bolts and nuts Hundred

or by screws, including oil painting with one coat of Fourteen and

primer of approved quality and brand & two coats of Paise Four Only

synthetic enamal oil paint etc. complete as per detail

drawing and as directed by Engineer in charge.

estimated Tendered Rates

Item according to

but may be Item of work Unit

less in figures In Words quantities

P & L 24" x 24" vitrified 8 mm thick tile flooring over

40 mm (average) base of cement mortar 1:6 (

cement: 6 coarse sand) on new surface or fixing on

existing flooring by adhesive material including

32 51.00 Sqm. 1485.00 Hundred Eighty

Applying spacer of 5mm and not less than 3mm

depth and filling groove with epoxy filler material of

laticrete , Roff or equivalent. & cleaning the surface

etc. complete for light shade

Providing and laying white glazed tiles 6mm thick in

flooring treads of steps and landing laid on a bed of

33 32.00 Sqm. 889.23 Nine and Paise

12mm thick cement mortar 1:3 (1-cement : 3-coarse

sand ) finishing with flush pointing in white cement.

Providing and laying white glazed tiles 6mm thick in

skrting risers of steps and dedo on 10mm thick

34 135.00 Sqm. 921.73 One and Paise

cement plaster 1:3 (1-cement : 3-coarse sand) and

jointed with white cement slurry

Providing and laying polished Granite Slab 18mm

thick in Risers of steps Dedo, window sill, jembs and Rupees Two

pillars laid 10mm thick Cement Mortar 1:3 (1- Thousand Seven

Cement : 3 coarse sand and jointed with Grey Hundred and

Cement Slurry including full molded round front Paise Four Only

edges , rubbing and polishing etc. complete.

Providing and laying polished Kota stone slab flooring

over 40mm (Average) thick base of cement mortar Rupees One

1:6 (1-cement : 6-coarse sand) or L.M. 1.1.5 (1-Lime Thousand

36 723.00 putty :1.5 - coarse sand) laid over and jointed with Sqm. 1019.39 Nineteen and

grey cement slurry mixed with pigment to match the Paise Thirty Nine

shade of slab including rubbing and polishing etc. Only

complete. (A) 25mm thick

Providing and laying polished kota stone slab 25mm

thick in risers of steps,skirting Dedo and pillars laid

on 10mm thick cement mortar 1:3 (1-Cement :

37 18.00 Sqm. 1135.48 Hundred Thirty

coarse sand) and jointed with gray cement slury

mixed with pigment to match the shade of slab

Forty Eight Only

including rubbing and polishing etc. complete.

Providing 10 mm thick cement mala plaster on Rupees One

ceiling and soffits of stairs for interior upto floor two Hundred Fifty

level, in cement mortar (1:4) (1 cement : 4 sand) etc Nine and Paise

complete. Ground floor Three Only

Providing 15 mm thick cement mala plaster in single

coat on fair side bricks/concret walls for interior

Hundred Seventy

39 233.00 plastering up to floor two level finished even and Sqm. 176.14

smooth in cement mortar 1:4 (1 cement : 4 sand)

etc complete. Ground Floor

estimated Tendered Rates

Item according to

but may be Item of work Unit

less in figures In Words quantities

Providing 15 mm thick cement mala plaster in single

coat on fair side bricks/concret walls for interior

40 40.00 plastering up to floor two level finished even and Sqm. 200.61

Paise Sixty One

smooth in cement mortar 1:4 (1 cement : 4 sand)

etc complete. First Floor

20mm.thick sand faced cement plaster on walls upto

height 10 meters above ground level consisting of

41 1055.00 12mm. Thick backing coat of CM.1:3 (1-cement:3- Sqm. 350.57

and Paise Fifty

sand) and 8mm.thick finishing coat of C.M. 1:1 (1-

cement:1-sand) etc. complete.

Providing throating or plaster drip and moulding to

42 78.00 Rmt 44.07 Four and Paise

R.C.C. Chajja etc.comp

Seven and Paise

43 147.00 Prov.20mm deep finished groove etc.comp Rmt 27.27

Providing and fixing chicken wiremesh jali at R.C.C. Hundred Seventy

44 47.00 masonry joints at any height with all labour & Sqm. 275.73 Five and Paise

material etc. complete. Seventy Three

Applying two coats of birla(White cement based) or

Asian (acrylic lappy putty) or equivalent two coats of

primer of approved brand and manufacture on new Rupees Forty

45 356.00 wall surface to give an even shade including Sqm. 40.59 and Paise Fifty

thoroughly brushing the surface free from mortar Nine Only

dropping and other matter foreign and sand papered

Wall painting (three coats) with plastic emulsion

paint of approved brand and manufacture on Rupees One

undecorated wall surface to give an even shade Hundred Twenty

including throughly brushing the surface free from Eight and Paise

mortar droppings and other foreign matter and sand Thirty Eight Only

papered smooth.

Finishing wall with weather proof exterior emulsion

paint on wall surface (two coats) to give an required

47 998.40 shape even shade after thoroughly brushing the Sqm. 122.14

surface to remove all dirt, and remains of loose

powdered materials.etc complete

Providing cement vata, 10 cm. x 10 cm. size, quarter

48 146.00 round in cement mortar 1:1 including neat cement Rmt 24.28

finishing, watering, etc. complete.

estimated Tendered Rates

Item according to

but may be Item of work Unit

less in figures In Words quantities

Providing and laying chaina mosic water proofing

treatment on terrace including applying neat cement

slurry 2.75 Kg./Sqm. Of cement admixed with water

proofing compound after cleaning the surface (b)

laying cement concrete usig brick bats 25 to 100 mm

size with 50% C.M. 1:5 (1 cement : 5 coarse sand)

admixed with water proofing compound over 20 mm

49 115.00 Sqm. 1395.99 Hundred Ninety

thick layer of C.M. 1:5 to required slope including

rounding of junction of walls and slabs (a) after two

Ninety Nine Only

days of proper curing applying a second with 20 mm

thick C.M. 1:4 and china mosaic tiling and finally

finishing the surface with trowel white cement slurry

(e) after finishing the whole terrace shall be flooded

with water for two weeks.

Structural steel work ( Confirming to IS 4923-1997)

riveted, bolted or welded in builtup for all type Rupees One

sections, in framed work, including cutting, hoisting, Hundred Thirty

50 144.00 fixing in position and applying a priming coat of Kg. 131.83 One and Paise

approved steel primer all complete as per the Eighty Three

structural designs and directions of Engineer in Only

Steel work, welded in built up sections framed work

including cutting, hoisting, fixing in position and

applying a priming coat of red lead paint. (A)In

51 180.00 beams and joists, channels angles Tees, flats, with Kg. 100.92

Paise Ninety Two

connecting plates or angle cleats as in main and cross

beams. Hip and jack rafters, purlins conneted to

common rafters and the like for Railing at Ramp

P&L 30 mm Thick MASTIC ASPHALT WEARING

COURSE while paving grade bitumen meeting the

requirments given in the MORTH specification table

500-29 prepared using Mastic Cooker and Laid to

required level and slope after cleaning the surface

including providing anti-solid surface with bitumen

precoated fine grained hard stone chipping of

52 1409.00 Sqm. 1191.80 Hundred Ninety

mm nominal size at the rate of .005 cumt per

Sq.Mt , and at abn approximate spacing of 10 cm

center to center in both directions , pressed into

surface when the temperature of surface is not less

than 1000 c , protruding 1mm to 4mm over Mastic

Asphalt surface ,all complete as per MORTH

Providing and casting in situ controlled cement Rupees Five

concrete M200 for average 75 mm thick wearing Thousand Three

53 16.00 coat laid as directed dincluding tamping, vibrating, Cum. 5320.25 Hundred Twenty

finishing, curing and filling in joints with bitumen and Paise

complete. Twenty Five Only

estimated Tendered Rates

Item according to

but may be Item of work Unit

less in figures In Words quantities

Providing and fixing pre- cast concrete kerb stone

of gray cement based concrete block 30 cm length, Rupees Three

30 cm height and 15cm thick of 250 grade concret as Hundred Seventy

per approved design and including excavation for Four and Paise

fixing in proper line and level, fillig the joint with C: M Ninety Two Only

1:3 ( 1 Cement : 3 Fine Sand) etc. complete

Providing and fixing pre-cast Rubber Dye / steel Dye

inter locking concrete block 60mm thick with grade

of concrete M300 pnumatic compressed / vibrated Rupees Seven

mechanically and as per approved design Confirming Hundred Seven

to IS 15658 : 2006 including 35 mm Sand layer for and Paise Fifty

levelling and filling the joint with sand in proper line Five Only

and level as per guidlines of IRC : SP 63-2018 etc.

Constructing brick masonry chamber for

underground C.I. Inspection chamber and bends with

bricks having crushing strength not less than

35Kg/Cm2 in C.M. 1:5 C.I. cover with frame (Light

duty) 455mm x 610mm intenal dimensions total Rupees Two

weight of cover with frame to be not less than .38Kg. Thousand Nine

(Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. Hundred Thirty

top slabe with1:2:4 mix (1-cement :2- coarse sand :4- Two and Paise

graded stone aggregate20mm size) foundation Ninety Three

concrete 1:5:10 inside plaster 15mm thick with Only

cement mortar 1:3 finished smooth with a floating

coat of neat cement on walls and bed concrete etc.

complete.(i) Inside dimensions 455mmx 610mm and

450mm deep for single pipe line.

Providing laying (to level or slopes) and jointing

reinforced concrete Light duty non-pressure pipes

57 63.00 I.S. class NP2 of the following internal diameter with Rmt 359.85

collars and butt ends prepared for collar joints

Eighty Five Only

including testing of joints complete.(C) 250mm

Providing and fixing S.W. gully trap with C.I. grating Rupees One

brick masonry chamber and water tight C.I. cover Thousand Two

58 3.00 with frame of 300mm x 300mm size (inside) with Each. 1292.19 Hundred Ninety

standard weight.(i) Square mouth traps. (A) 100mm Two and Paise

x 100mm size P type Nineteen Only

Providing and fixing P V C SWR pipes (IS 13592) Rupees Seventy

59 77.00 spigot and socket soil waste and ventilating pipe of Rmt 70.70 and Paise

the following nominal size 160 mm dia Seventy Only

Steel work welded in built up sections framed work

including cutting, hoisting, fixing in position and

applying a priming coat of red lead paint. [A.] In Rupees Ninety

60 19634.00 beams and joists, channels angles tees, flats with Kg. 91.08 One and Paise

connecting plates or angle cleats as in main and cross Eight Only

beams, Hip and jack rafters, purlins connected to

common rafters and the like.

estimated Tendered Rates

Item according to

but may be Item of work Unit

less in figures In Words quantities

Painting two coats (excluding priming coat) on new

steel and other metal surface with enamel paint, Rupees Ninety

61 556.00 brushing, interior to give an even shade including Sqm. 94.39 Four and Paise

cleaning the surface an even shade including cleanicn Thirty Nine Only

the surface of all dirt, dust and other foreign matter.

Providing and fixing wsh down water closet

(European type, W.C. Pan) with integral P or S trap

including jointing the trap with soil pipe in Cement

62 8.00 Each 1356.81 Hundred Fifty Six

Mortar 1:1 (1-Cement : 1-fine sand) (Seal and cover

and Paise Eighty

to be measured and paid for separately)(A) vitreous

China Pattern :(i) in white colour

Providing and fixing plastic seat and cover for wash

63 8.00 down water closer with C.P. brass hinges and rubber Each 291.33

Thirty Three Only

Providing and fixing washbasin with single hole for Rupees One

pillar tap with C.I. or M.S. brackets painted white Thousand Five

including sutting holes and making good the same Hundred Twenty

but excluding fittings.(A) Vitreous China:(ii) Flat Back and Paise

washbasin 550 mm x v 400mm size. (i) In white Twenty Four

Providing and fixing C.P. brass waste for washbasin Nine and Paise

or sink. (B) 40mm dia Eighty Three

Providing and fixing M.I. fisher union for washbasin

66 6.00 Each 88.65 Eight and Paise

or sink. (B) 40mm dia

Sixty Five Only

Providing and fixing chromium plated, bottle trap

67 6.00 with necessary couplings of approved quality for Each 295.80

Providing and fixing Urinal or approved quality

including conecting the Urinal with waste pipe , tap

68 3.00 Each 1074.86 Seventy Four and

etc. complete.(A) White earthenware flat back or

Paise Eighty Six

corner type size 430mm x 260mm x 350mm.

Providing and fixing 600mm x 450mm bevelled edge Rupees Eight

mirrror of superior glass mounted on 6mm thick A.C. Hundred Fifty

sheet or plywood sheet and fixing to wooden pluge Nine and Paise

with C.P. brass screws and washers. Forty One Only

Providing and fixing C.P. brass towel rail comlete

Hundred Sixteen

70 6.00 with C.P. brass brackets fixed to wooden plugs with Each 616.42

and Paise Forty

C.P. brass scews.(B) 600mm x 20mm size.

estimated Tendered Rates

Item according to

but may be Item of work Unit

less in figures In Words quantities

Providing and fixing PVC SWR Nahni trap IS 14735 for

drain - 100 mm diameter with jali of the following

71 11.00 nominal diameter of self cleansing design with C.I Each 600.23

scread down or hinged grating including the cost of

cutting and making good the walls

Providing and fixing to wall ceiling and floor 10.0 Kg.

F/Cm2 working pressure polythene pipes of the

following outside Dia. Low densidy, complete with

72 44.00 Rmt 280.23 and Paise

special falnge compression type fittings, wall clipsetc.

including making good the wall ceiling and floor.(F)

Providing and fixing to wall ceiling and floor 10.0 Kg.

F/Cm2 working pressure poluthene pipes of the

following outside Dia. Low densidy, complete with

73 28.00 Rmt 258.23 Eight and Paise

special falnge compression type fittings, wall clipsetc.

including making good the wall ceiling and

floor.(G)110 mm

Providing and fixing S.W. gully trap with C.I. grating Rupees One

brick masonry chamber and water tight C.I. cover Thousand Two

74 2.00 with frame of 300mm x 300mm size (inside) with Each 1246.92 Hundred Forty

standard weight.(i) Square mouth traps.(B) 150mm x Six and Paise

100mm size P or R type Ninety Two Only

Constructing brick masonry chamber for

underground C.I. Inspection chamber and bends with

bricks having crushing strength not less than

35Kg/Cm2 in C.M. 1:5 C.I. cover with frame (Light

duty) 455mm x 610mm intenal dimensions total Rupees Two

weight of cover with frame to be not less than 38Kg. Thousand Nine

(Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. Hundred Thirty

top slabe with 1:2:4 mix (1-cement :2- coarse sand :4- Two and Paise

graded stone aggregate 20mm size) foundation Ninety Three

concrete 1:5:10 inside plaster 15mm thick with Only

cement mortar 1:3 finished smooth with a floating

coat of neat cement on walls and bed concrete etc.

complete.(i) Inside dimensions 455mmx 610mm and

450mm deep for single pipe line.

Providing laying and jointing in true line and level

15mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water

including fittings as approved by Engineer In Charge.

Pipe shall be fixed on the wall with the help of clamp

76 200.00 Rmt 72.65 Two and Paise

at every two metre C/C or shall be concealed as

Sixty Five Only

directed including necessary fittings etc. including

testing of pipe and joints and fixing the same with

adhesive solvent, including cost of all materials

estimated Tendered Rates

Item according to

but may be Item of work Unit

less in figures In Words quantities

Providing laying and jointing in true line and level

25mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water

including fittings as approved by Engineer In Charge.

Pipe shall be fixed on the wall with the help of clamp

77 250.00 Rmt 91.84 One and Paise

at every two metre C/C or shall be concealed as

Eighty Four Only

directed including necessary fittings etc. including

testing of pipe and joints and fixing the same with

adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level

40mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water

including fittings as approved by Engineer In Charge. Rupees One

Pipe shall be fixed on the wall with the help of clamp Hundred Forty

at every two metre C/C or shall be concealed as Eight and Paise

directed including necessary fittings etc. including Twelve Only

testing of pipe and joints and fixing the same with

adhesive solvent, including cost of all materials.

Providing corrugated G.I. sheet of class-3 roofing

fixed with glavanished iron J or L Hooks, Bolts and Rupees Seven

nuts 8mm diameter with bitumen and G.I. limpet Hundred Thirty

washer or G.I. limpet washer. filled with white lead Four and Paise

complete excluding the cost of purlins, Rafters and Nineteen Only

Trusses.(1) 0.80 mm thick sheet.

Providing and fixing 150mm wide 450mm over all

semicircular plain G.I.sheet class-3 gutter with Iron

80 54.00 brackets 40mm x 3mm size Bolts, Nuts, washers etc. Sqm. 581.32

including making necessary connection with rain

Thirty Two Only

water pipes. (i) 0.80 mm thick Sheet.

Providing, supplying & placing precast RCC Woodeny

benches as per given specifications. (Seating plank

dimensions : Seating Length of the Bench : 1380 mm,

Seating width of the Bench : 450 mm, Seating height

of the Bench : 450 mm, Seating plank thickness :

mm, Total height of the Bench : 900 mm. ),M-30 Rupees Five

grade of Concrete using vibration compaction Thousand Four

81 56.00 process. Benches consists of 2 Nos. L-shape base No. 5474.20 Hundred Seventy

support in wooden texture and 1 Nos. flate back and Four and Paise

1 Nos. bottom plank leg thickness :90 mm, Leg hight Twenty Only

: 830 mm, Leg width : 600 mm, backside plank width

: 350 mm, backside plank length : 1380 mm,

backside plank thickness : 60 mm.All parts are joined

together with galvanized bolts of suitable size and

bolts are sealed with cover

Providing and fixing screw down bib taps of following Hundred Eighty

82 8.00 size.(A) Brass screw down bib tap polished bright. (i) Each 186.83 Six and Paise

15mm dia. Eighty Three

estimated Tendered Rates

Item according to

but may be Item of work Unit

less in figures In Words quantities

5 Providing and fixing pillar tap, capstan head, screw Hundred Eight

83 6.00 down high pressure with screws, shanks and back Each 308.73 and Paise

nuts. (i) 15mm dia. Seventy Three

Providing and fixing brass screw down stop tap.(A) Hundred Five

15mm dia and Paise Eighty

Providing and fixing chromium plated brass half trun Hundred Sixty

85 8.00 flush cock of approved quality including fixing in pipe Each 263.77 Three and Paise

line etc. complete.(ii) 25mm dia. Seventy Seven

Providing and fixing ball cock of approved. quality as Hundred Thirty

directed.(A) Copper Metal (i) 25mm dia Two and Paise

Eighty Nine Only

Providing and fixing in position cowel went to Hundred Ninety

pipes.(B) 75mm dia Three and Paise

Providing and fixing in position cowel went to Hundred Five

pipes.(C) 100mm dia and Paise

Providing erecting and fixing double coated ISI water Rupees Three

89 1000.00 tank of required capacity each with all necessary litre 3.95 and Paise Ninety

fittings and connection etc. complete on terrace Five Only

Point wiring for Light / Bell with 2-1.5 sq.mm &

earth wire of 1.5 sq.mm (Green) both are of ISI

marked 1.1 KV grade FRLS PVC insulated multi strand

copper wires up to 10 mtr length , in below type of

pipe erected with 6A Modular type switch / bell

push & accessories and earth continuity of following Rupees Four

type, erected on PVC / Metallic/Wooden box, single Hundred Eighty

mounting base frame covered with Five and Paise

textured/metallic/white front plate modules erected Eighty One Only

on / in wall / ceiling as per pipe erected, with

necessary Lamp holder/ceiling rose / H.D.Connector

as directed. (f) with medium class Rigid PVC pipe and

accessories erected concealed in wall/ceiling

complete Cat. III

estimated Tendered Rates

Item according to

but may be Item of work Unit

less in figures In Words quantities

Point wiring for Tissino / Modular secondary light

point with 2-1.5 sq.mm & earth wire of 1.5 sq.mm

(green) both are of ISI marked 1.1 KV grade FRLS PVC

insulated multi strand copper wires, in below type of

pipe to be erected complete with earth continuity

and necessary connection with primary light with

91 53.00 accessories erected on Metal / PVC / wooden box Pt. 167.66

Seven and Paise

covered with 3 mm thick PC(Polycarbonate) / Acrylic

sheet for open / concealed wiring. with necessary

Lamp holder / ceiling rose / H.D.Connector as

directed. (f) with medium class Rigid PVC pipe and

accessories erected concealed in wall/ceiling

Point wiring for FAN with 2-1.5 sq.mm & earth wire

of 1.5 sq.mm (Green) both are of .ISI marked 1.1 KV

Grade FRLS PVC insulated multi strand copper wires

up to 10 mtr length, in below type of pipe erected

with 6A Modular type switch and hum free EME step

type electronic fan regulator mounted and Rupees Six

accessories with earth continuity of following type Hundred Seventy

erected on PVC / Metallic/Wooden box, single Four and Paise

mounting base frame covered with Sixty Eight Only

textured/metallic/white front plate modules erected

on / in wall / ceiling as per pipe erected. with

necessary ceiling rose / H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories

erected concealed in wall/ceiling complete Cat. III

Providing and erecting Mains with 1.1 KV grade FRLS

PVC insulated ISI marked stranded Copper conductor

wire in following type of pipe to be erected

Rupees Sixty Two

concealed in /flushed on wall/ceiling, with 1.5 sq.

93 80.00 Mtr 62.62 and Paise Sixty

mm copper conductor FRLS PVC insulated stranded

wire of green colour for earth continuity of following

size (A) With medium class Rigid PVC pipe and

accessories (a) 2 wire 1.5 sq. mm

Providing and erecting Mains with 1.1 KV grade FRLS

PVC insulated ISI marked stranded Copper conductor

wire in following type of pipe to be erected

concealed in /flushed on wall/ceiling, with 1.5 sq.

94 110.00 Mtr 82.82 Two and Paise

mm copper conductor FRLS PVC insulated stranded

Eighty Two Only

wire of green colour for earth continuity of following

size (A) With medium class Rigid PVC pipe and

accessories (b) 2 wire 2.5 sq. mm

estimated Tendered Rates

Item according to

but may be Item of work Unit

less in figures In Words quantities

Point wiring for Individual Plug with & earth wire of

1.5 sq.mm (Green) both are of ISI marked 1.1 KV

grade FRLS PVC insulated multi strand copper wires

up to 10 mtr length, in below type of pipe erected

complete with Modular type switch & 5 pin Plug Rupees Four

erected on PVC / Metallic/Wooden box covered with Hundred Seventy

95 10.00 appropriate front plate modules erected on / in wall Pt. 475.71 Five and Paise

/ ceiling as per pipe erected with following type of Seventy One

accessories.[I] For 6A Plug and 6 a switch with 2-1.5 Only

sq.mm Cu. Wire from nearby switchboard/mcb db

board.(f) with medium class Rigid PVC pipe and

accessories erected concealed in wall/ceiling

complete Cat. III

Point wiring for Individual Plug with & earth wire of

1.5 sq.mm (Green) both are of ISI marked 1.1 KV

grade FRLS PVC insulated multi strand copper wires

up to 10 mtr length, in below type of pipe erected

complete with Modular type switch & 5 pin Plug Rupees Seven

erected on PVC / Metallic/Wooden box covered with Hundred Forty

appropriate front plate modules erected on / in wall Five and Paise

/ ceiling as per pipe erected with following type of Thirty Eight Only

accessories.[II] For 16A Plug and 16 amp switch with

2-2.5 sq.mm Cu. Wire from mcb db board.(f) with

medium class Rigid PVC pipe and accessories erected

concealed in wall/ceiling complete Cat. III

Point wiring for Individual Plug with & earth wire of

1.5 sq.mm (Green) both are of ISI marked 1.1 KV

grade FRLS PVC insulated multi strand copper wires

up to 10 mtr length, in below type of pipe erected

complete with Modular type switch & 5 pin Plug

erected on PVC / Metallic/Wooden box covered with

97 1.00 appropriate front plate modules erected on / in wall Pt. 818.10

/ ceiling as per pipe erected with following type of

accessories.[III] For 16A Plug and 16 amp switch with

2-4 sq.mm Cu. Wire with 2.5 sq.mm ( green) earthing

wire from mcb d b board.(f) with medium class Rigid

PVC pipe and accessories erected concealed in

wall/ceiling complete Cat. III

Point wiring for on board Looped Plug with 6A

Modular type switch & 5 pin socket erected on PVC / Rupees Two

Metallic/Wooden box, single mounting base frame Hundred Forty

covered with textured /metallic/white front plate One and Paise

modules erected on / in wall / ceiling with following Thirty Nine Only

type accessories Cat. III

estimated Tendered Rates

Item according to

but may be Item of work Unit

less in figures In Words quantities

Providing & Erecting approved make following size of

TV Co-axial flexible cable comprising inner conductor Rupees Thirty

of solid bare copper insulated with Foam PE & Seven and Paise

Secondary conductor made of poly- Aluminium film Thirty Seven

bonded Al. Braids @ suitable coverage overall Only

sheathed with black PVC insulation. b).RG-6

Supplying & erecting approved make Telephone

Cable electrolytic copper conductor PE insulation

twisted in two pairs, & wrapped with FRLS PVC tape

& sheathed with FRLS PVC or HFFR outer Jacket Rupees Nineteen

100 90.00 suitable for telephone wiring & confirming to C-DOT Mtr 19.19 and Paise

erected in existing pipe. of following size of Nineteen Only

conductors & nos.of pairs. With necessary

connections.[A] Conductor Size 0.5 mm (a)

Unarmoured 2) Two Pairs

Providing and erecting ISI mark Medium class RIGID

PVC PIPES of following size complete to be erected Rupees Twenty

on/in wall or ceiling erected with necessary PVC Three and Paise

fittings & Junction boxes fixed with adhesive solution Twenty Three

& Clamps with following dia of pipes, in approved Only

manner as directed.(a)20 mm

Providing and erecting ISI mark Medium class RIGID

PVC PIPES of following size complete to be erected

on/in wall or ceiling erected with necessary PVC

102 110.00 Mtr 32.32 Two and Paise

fittings & Junction boxes fixed with adhesive solution

Thirty Two Only

& Clamps with following dia of pipes, in approved

manner as directed.(b) 25 mm

Providing and fixing approved make Perforated C

type cable tray. Made from pre- galvanized sheet

steel. The cable tray should be bended as per IS Rupees Three

2062/1079 . with max 17.5% perforation with Hundred Twenty

coupler plate / Fish plate and GI hardware like nut - Two and Paise

bolt and washers etc. erected on existing support as Nineteen Only

per Specification and as per instruction of engineer

in charge(3) 150 X 50 X 1.5 mm Thick

Providing following type of Modular Type

Accessories mounted with PVC / metallic/Wooden

box, single mounting base frame covered with Rupees One

textured / metallic/white front plate , modules Hundred Fifty

erected with necessary connections as per site Three and Paise

situation directed by Engineer In charge.(3)Two pin Fifty Two Only

RJ-11 Telephone socket with top [A] For One Gang

Providing following type of Modular Type

Accessories mounted with PVC / metallic/Wooden

box, single mounting base frame covered with

105 1.00 textured / metallic/white front plate , modules Ea. 153.52

Three and Paise

erected with necessary connections as per site

situation directed by Engineer In charge.(4) TV Co-

axial Socket outlet Cat. III

estimated Tendered Rates

Item according to

but may be Item of work Unit

less in figures In Words quantities

Providing & erecting Switch board for Computer or

electric apparatus consisting of following modular

type accessories mounted with PVC / Metallic Rupees One

concealed/open box with single mounting base Thousand Eighty

106 1.00 frame covered with textured/metallic /white front Ea. 1081.71 One and Paise

plate,modules erected with necessary connections as Seventy One

directed. 1 no. 6A/16A universal plug-switch Only

combined.3 nos. 6A Switch 3 nos. 6A 5 pin Plug .For

Modular Type Accessories Cat.III

Supplying and erecting LED indoor fittings with LEDs

of wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be

made of thick sheet Steel conforming to IS:

513/CRCA/ aluminium die cast powder coated and

high U.V. & corrosion resistance with diffuser with

company mark/name 160V to 270V, Power Factor Rupees Three

more than 0.95, THD < 15%, CCT 3000 K to 6500K, Hundred Seventy

Luminaire efficacy> 85 lumens/watt ,LED Three and Paise

LED driver efficiency > 85 % ( fitting required LM-79 Seventy Only

& LM-80 Certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED fittings.The

Engineer incharge may select any wattage capacity

between the ranges shown.) (A) Tube Light with

integral driver (iv) 22-24 Watts, Surge - 2KV,IP-20,

conventional 4 feet Cat-III

Supplying and erecting led lamps with following

wattage capacity of 220 to 240 voltage, minimum

15000 burning hours life, 500 V in built-surge

108 12.00 protection,Polycarbonate diffuser, mounting suitable Ea. 112.11

and Paise Eleven

for E14 / E27 / B22 lamp holders, pf >= 0.5 (A) LED

Lamps integral type, with PC diffuser suitable LAMP

holder (ii) 5 to 8 watts Cat III

Supplying and erecting approved make oscillating

type bracket fan A.C. 23OV. 50cy/s 400/450 mm

sweep wall mounted with height adjustment and

109 30.00 Ea. 2534.09 Hundred Thirty

rotary tilting device complete with guard, flexible

Core plug top complete erected with lead wires as

directed. Cat.II

Providing & erecting Approved make Power Saving

50 Watt Ceiling Fan with double ball bearing ISI mark

with Condenser 230 volt A.C. 50 Hz 1200 mm sweep

110 5.00 complete having 3blades with aluminium blades with Ea. 1948.29

Eight and Paise

, canopy & 30 cm. down rod erected with

earthing.(Make shall be approved by Engineer in

Supplying & erecting fan hook box of 10 mm M.S.

round bar bounded to the RCC bars up to 50mm

111 5.00 length each side and pierced through a 16 Gauge Ea. 108.07

and Paise Seven

M.S. box / Heavy Duty PVC box complete erected

concealed in Ceiling with necessary finishing.

estimated Tendered Rates

Item according to

but may be Item of work Unit

less in figures In Words quantities

Rupees Eighteen

Providing 2.5mm.thick laminated acrylic sheet to

112 5.00 Ea. 18.18 and Paise

cover the fan hook or Fan box.

Supplying & erecting approved make low noise

decorative exhaust fan having square frame ABS

113 4.00 Ea. 1366.53 Hundred Sixty Six

body with inbuilt lowers & square frame.250mm

and Paise Fifty

with 1350 RPM Cat.II

Supplying and erecting 19 / 20 mm. nominal bore Rupees One

Medium Class M.S. Pipe down rod erected duly Hundred Eight

painted for fan complete with proper insulation and Paise Seven

without leakage and earthing. Only

Providing & erecting water cooler having storage

capacity 150 Ltr. & cooling capacity 150 Ltr.per hour

@ an ambient temp of 45˚ C. The outlet temp. of the Rupees Forty Six

water should drop by 15˚C within a hour, The water Thousand Six

cooler should be comprising of hermetically sealed Hundred Forty

compressor, fan motor, condensing unit, water tank Eight and Paise

surrounded by evaporating, coil, thermostats, relay Eighty Seven

etc.complete with necessary inlet & outlet Only

connection. The body of water cooler will be made

from Stainless Steel.

Supplying & erecting 5 stage single reverse osmosis

water purification system with M.S. powder coated

frame, prefilter housing with 'O' ring presediment

filter GAC filter, carbon filter suitable buster DC

116 1.00 pump capacity 80 psi, mention with 40 psi inline type Ea. 24394.53

Ninety Four and

post carbon filter auto low & high pressure switches

Paise Fifty Three

with following size of storage tank & LPH capacity &

erected as directed [C] 50 Ltr / Hr with 150 psi 2 nos

Supplying & erecting UPVC Mini trunking (PVC Casing-

n-Capping) having double-locking arrangement with

grooves, trunking of size not below 12.5 mm in Rupees Thirty

117 20.00 height as per IS with accessories of PVC/Resin Mtr. 30.30 and Paise Thirty

polypropylene not below 1.8 mm thick duly sealed in Only

joint & erected on wall / ceiling of following size .(2)

estimated Tendered Rates

Item according to

but may be Item of work Unit

less in figures In Words quantities

Supplying and erecting approved make online Un-

interruptible Power Supply system comprising flat

cum-boost charger with IGBT base rectifier &

Inverter & sealed maintenance free SMF batteries.

The charger having operating capacity for input 160-

270V AC & inverter having output 230V,50 Hz Ac

118 1.00 with 0.8 load power factor with battery, over/under Ea. 69331.45

voltage output with over load & short circuit

Paise Forty Five

protection equipment. The system housed in CRC

sheet duly powder coated paint with following

power backup.with MS painted batteries stand, 10%

Overload capacity for momentary load. (A) 1 KVA

with 1Hr Backup

Supplying & erecting approved make plan

instrument having One junction line & One extension

(Plan 1 + 1 ) with Chairman /secretary facilities with

119 1.00 Ea 2543.18 Hundred Forty

extension CLI & speaker phone instruments .

Three and Paise

[[Approved by Competent Authority i.e. not Below

the rank of Executive Engineer ]

Supplying & erecting push button type telephone

instrument having speaker phone Caller ID & speaker Rupees Eight

phone with one touch memory (min.6 nos.)& 99 Hundred Ninety

memories with display system Single line [[Approved Eight and Paise

by Competent Authority i.e. not Below the rank of Ninety Only

Executive Engineer ]

Supplying & erecting approved make LAN cable of Rupees Forty

121 90.00 following size in existing pipe as per direction [C] CAT Mtr 45.45 Five and Paise

-6 Forty Five Only

Supply & installation of modular type accessories for

U PVC snap-on adaptable trunking/Pop up Box with

122 2.00 required items erected with necessary connection. Ea 540.35

and Paise Thirty

As desired by Engineer In charge vi) Cat-6 LAN Socket

providing and erecting Miniature circuit breaker Rupees Two

single pole 0.5A to 2A system and having breaking Hundred Seventy

capacity 10 KA to be erected in existing box. and Paise Sixty

confirming to IS 8828/1996 with ISI Mark Cat.III Eight Only

Providing and erecting Miniature circuit breaker

single pole 6A to 25A suitable to operate on 240 V

124 72.00 A.C. system and having breaking capacity 10 KA to be Ea. 112.11

and Paise Eleven

erected in existing box. confirming to IS 8828/1996

with ISI Mark Cat.III

Providing & erecting 415 V MCB Four Pole for Motor Rupees Seven

& Inductive Load (C Curve) having 10KA breaking Hundred Thirty

capacity & confirms to IS :8828 in existing box having Seven and Paise

following capacity (c)63 Amp Cat.III Thirty Only

estimated Tendered Rates

Item according to

but may be Item of work Unit

less in figures In Words quantities

Providing & erecting 415 V MCB Four Pole for Motor Rupees Six

& Inductive Load (C Curve) having 10KA breaking Hundred Sixty

capacity & confirms to IS :8828 in existing box having Eight and Paise

following capacity (b)40 Amp. Cat.III Sixty Two Only

Providing & erecting 240 V MCB double pole switch

for lighting Load (B Curve) having 10 KA breaking

127 1.00 Ea. 295.93 Five and Paise

capacity & confirms to IS : 8828 in existing box

having following capacity (B) 40 Amp. Cat.III

Providing and erecting Approved make RCCBs

conforming to IS: 12640 and having sensitivity of

mA and Short Circuit withstand capacity of 10 KA and

suitable for operation on 3 phase and neutral

128 1.00 415V,50Hz. having characteristic of quick action & Ea. 4314.72

tripping with all advance feature & do not

incorporate any electronic component for following

Max. rating erected as directed. (iv) 100 Amps. FP

(100 mA Sensitivity) Cat. III

providing and erecting Approved make RCCBs

conforming to IS: 12640 and having sensitivity of

mA and Short Circuit withstand capacity of 10 KA and

suitable for operation on single phase 240 V,50Hz.

129 1.00 Ea. 1969.50 Hundred Sixty

having characteristic of quick action & tripping with

all advance feature & do not incorporate any

electronic component. for following Max. rating

erected as directed (i) 25 Amps.DP Cat. III

Providing and erecting Sheet Steel powder coated

MCB distribution board - flush / surface mounted

fitted with busbar, neutral link, earth bar and DIN Rupees Three

rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 Thousand Four

without MCB to house appropriate nos. of Hundred Twelve

MCBs.(The DBs should be used of same company of and Paise

MCB to be used) suitable for (B) three phase Seventy Nine

incoming and single phase horizontal type outgoing Only

Per phase isolation type (PPI) (b) sheet steel double

door (iii)8 way

Providing and erecting Sheet Steel powder coated

MCB distribution board - flush / surface mounted

fitted with busbar, neutral link, earth bar and DIN

rail, Conforms to IS 8623-1 & 3, IEC 61439-1 &

131 5.00 without MCB to house appropriate nos. of Ea. 1492.78

MCBs.(The DBs should be used of same company of

MCB to be used) suitable for (A) single phase

incoming and horizontal single phase outgoing (b)

sheet steel double door (IP-43) (iv)12 way

estimated Tendered Rates

Item according to

but may be Item of work Unit

less in figures In Words quantities

Supplying & erecting approved make RCCB + MCB

(Electro magnetic type only) working on residual

current device having 10 KA short circuit breaking Rupees One

capacity and 30 mAmp. Sensitivity & 30 mili sec. Thousand Eight

132 5.00 tripping time conforming to IS 12640 test knob Ea. 1815.98 Hundred Fifteen

facility trip free mechanism operating for rated and Paise Ninety

leakage at nominal ten volt, complete erected Eight Only

including all materials lugs screws etc. completed. [a]

6A / 10A / 16A / 20A / 25A 2 pole single phase Cat. II

Providing & erecting weather proof, dust & vermin

proof, floor mounted front operated indoor type

cubical panel board necessary IP42 and above

protection as per approval from engineer incharge

made from 14 SWG thick CRC M.S. sheet for outer

body & doors, 16 SWG thick CRC M.S.sheet for

internal partitions with necessary accesories

supporting angles/ flats channel including cutting,

bending, drilling, welding, riveting with internal

partitions & cable alley as per requirements &

instruction of engineer-in-charge with erection of

supplied switch gears, BUSBARS, suitable size of inter

connecting PVC copper wire / copperaluminium

strips, rubber grommets, rib, bakelite control

133 2.00 Sq Mtr 16392.30 Hundred Ninety

fuses/MCB for measuring instruments, earth bus &

earth bolts, foundation flange - boltsbase Plates,

sufficient nos. of hinged doors, handles with locking

arrangement and rubber gasket,heavy duty end

terminal connection,danger notice board,necessary

ventilation,earthing strip complete. The Panel shall

be painted with epoxy powder coating.(The rates

excludes the cost of switchgears, bus bars, inter

connecting mains & Copper Aluminium strips,

meters, Fuses etc. The dimension shall be measured

excluding base beams) The panel shall be supplied

with following approved manufacturers with

followingsize.(C) The standard companies switch

gear shall be used and only manufacturers at CPRI

Providing and erecting Approved make Four pole

moulded case circuit breaker having breaking

capacity ICU of 35 KA. at 415 V. having Normal

current rating 200A.with variable Thermal &

134 2.00 Ea. 16221.61 Hundred Twenty

magnetic release suitable to work on A.C.supply

c/s. with all internal connections, spreader tinned

copper & complete erected in existing

G.M.S.housing ICS=100% of ICU only Cat III

Operational Handle Assembly Complete for (ii) 200 / Hundred Fifty

250 / 320 / 400 / 630 / 800 Amps Four and Paise

Forty Seven Only

estimated Tendered Rates

Item according to

but may be Item of work Unit

less in figures In Words quantities

Providing and erecting metallic vitrified danger

notice board as per language suggested by engineer

136 7.00 Ea. 69.69 Nine and Paise

incharge for MEDIUM VOLTAGE installation to be

Sixty Nine Only

erected as per IS-2551.

Providing & erecting High Voltage Danger Notice Rupees Thirty

137 2.00 Board sticker as per language suggested by engineer Ea. 35.35 Five and Paise

incharge of standard size-as per IS 2551 Thirty Five Only

Erection & connection Charges for 200A/ 250A/

138 2.00 A /325 A/400 A HRC TPN as following (b)Erection on Ea. 197.96

Seven and Paise

New angle iron frame duly painted with red oxide .

Ninety Six Only

Providing and erecting Mains with 1.1 KV grade FRLS

PVC insulated ISI marked stranded Copper conductor

wire in following type of pipe to be erected in / on Rupees One

wall / ceiling with 2.5 sq. mm copper conductor FRLS Hundred Seven

PVC insulated stranded wire of green colour for and Paise Six

earth continuity of following size(A) with medium Only

class Rigid PVC pipe and accessories.(a) 2 wire 4 sq.

Providing and erecting Mains with 1.1 KV grade FRLS

PVC insulated ISI marked stranded Copper conductor

wire in following type of pipe to be erected in / on Rupees One

wall / ceiling with 2.5 sq. mm copper conductor FRLS Hundred Forty

PVC insulated stranded wire of green colour for and Paise Thirty

earth continuity of following size(A) with medium Nine Only

class Rigid PVC pipe and accessories.(b) 2 wire 6 sq.

Providing and erecting Mains with 1.1 KV grade FRLS

PVC insulated ISI marked stranded Copper conductor

wire in following type of pipe to be erected in / on Rupees Two

wall / ceiling with 2.5 sq. mm copper conductor FRLS Hundred Forty

PVC insulated stranded wire of green colour for Eight and Paise

earth continuity of following size(A) with medium Forty Six Only

class Rigid PVC pipe and accessories.(h) 4 wire 6 sq.

Supplying & erecting Flexible PVC insulated

multistrand multicore 1.1 KV grade ISI marked Rupees Forty

142 50.00 Copper Wires of following Size to be erected as Mtr. 44.44 Four and Paise

directed. e) 1.50 Sq.mm 3 core round PVC sheathed Forty Four Only

Providing and erecting XLPE(IS:7098)(I)-88 ISI

armoured cable multistrand Aluminium conductor

143 20.00 for 1.1 KV. to be laid on wall with necessary clamps Mtr 141.40

or in existing trench / pipe of following size of

cables. (E) 3 core 16 Sq. mm

estimated Tendered Rates

Item according to

but may be Item of work Unit

less in figures In Words quantities

Providing and erecting XLPE(IS:7098)(I)-88 ISI

armoured cable multistrand Copper conductor for

Hundred Seventy

144 200.00 1.1 KV. to be laid on wall with necessary clamps or in Mtr 673.67

Three and Paise

existing trench / pipe at road crossing or floor of

Sixty Seven Only

following size of cables.(A) 4 core 10 Sq. mm

Providing and erecting XLPE(IS:7098)(I)-88 ISI

armoured cable multistrand / Solid Copper Rupees Five

conductor for 1.1 KV. to be laid on wall with Hundred Eight

necessary clamps or in existing trench / pipe at road and Paise Three

crossing or floor of following size of cables. (C) 4 Only

Providing and erecting XLPE(IS:7098)(I)-88 ISI Rupees Nine

armoured cable multistrand Copper conductor for Hundred Eighty

146 150.00 1.1 KV. to be laid on wall with necessary clamps or in Mtr 984.75 Four and Paise

existing trench / pipe at road crossing or floor of Seventy Five

following size of cables. (B) 4 core 16 Sq. mm Only

Providing and, fixing heavy duty flange type brass

cable gland with rubber ring for PVC insulated Rupees Forty

147 6.00 armoured cable complete with out going tails, Ea. 47.47 Seven and Paise

insulating tape etc for following size of cables. (D) 2 Forty Seven Only

to 4 core 16 Sq. mm

Providing and, fixing heavy duty flange type brass

cable gland with rubber ring for PVC insulated Rupees Thirty

148 8.00 armoured cable complete with out going tails, Ea. 38.38 Eight and Paise

insulating tape etc for following size of cables. (B) 2 Thirty Eight Only

to 4 core 6 Sq. mm

Providing and, fixing heavy duty flange type brass

cable gland with rubber ring for PVC insulated Rupees Thirty

149 6.00 armoured cable complete with out going tails, Ea. 38.38 Eight and Paise

insulating tape etc for following size of cables. (C) 2 Thirty Eight Only

to 4 core 10 Sq. mm

Solder less crimping type Copper lugs conforming to

IS suitable for cable of following size evenly crimped

Rupees Eight and

150 32.00 with high pressure tool & connected to switchgear Ea. 8.08

Paise Eight Only

terminals with brass/cadmium plated nut bolts in an

approved manner. (A) 1.5/2.5 to 6 Sq.mm

Solder less crimping type Copper lugs conforming to

IS suitable for cable of following size evenly crimped

151 24.00 with high pressure tool & connected to switchgear Ea. 10.10

terminals with brass/cadmium plated nut bolts in an

approved manner. (B) 10 Sq.mm

Solder less crimping type Copper lugs conforming to

IS suitable for cable of following size evenly crimped Rupees Twelve

152 24.00 with high pressure tool & connected to switchgear Ea. 12.12 and Paise Twelve

terminals with brass/cadmium plated nut bolts in an Only

approved manner. (C) 16 Sq.mm.

estimated Tendered Rates

Item according to

but may be Item of work Unit

less in figures In Words quantities

Providing and erecting Mains with ISI marked, 1.5KV

grade electrolyte multi stranded, annealed copper

conductor with heat resistant PVC insulated

conforms to IS 694, IEC - 227 erected in existing pipe

153 10.00 Mtr 16.16 and Paise Sixteen

of following size (Specifically for control panel, relays,

power switchgears, motor starters & control wiring)

with required size of copper lugs, nuts and bolts if

required.(b) One wire 1.50 sq. mm

154 10.00 (c) One wire 2.50 sq. mm Mtr 26.26 Six and Paise

Twenty Six Only

155 10.00 (e) One wire 6.00 sq. mm Mtr 53.53 Three and Paise

Fifty Three Only

Seven and Paise

156 10.00 (f) One wire 10.00 sq. mm Mtr 87.87

157 10.00 (g) One wire 16.00 sq. mm Mtr 135.34

Thirty Four Only

158 10.00 (h) One wire 25.00 sq. mm Mtr 225.23 Five and Paise

159 10.00 (j) One wire 50.00 sq. mm Mtr 448.44

Eight and Paise

Forty Four Only

Making trench in soft soil of suitable width of 90 cm

Rupees Forty Six

deep for laying cable or locating the fault all over the

160 200.00 Mtr. 46.46 and Paise Forty

run and back filling the same and making the surface

as normal ground.

Providing & laying approved make Double walled

corrugated pipes (DWC) of polyethylene(conforming

Rupees Sixty Two

to IS 14930 II )with necessary connecting accessories

161 200.00 Mtr. 62.62 and Paise Sixty

of same material at required depth in existing trench

for laying of cable. below ground / road surface for

enclosing cable (A)50 mm outer dia.

Providing & laying approved make Double walled

corrugated pipes (DWC) of polyethylene(conforming Rupees One

to IS 14930 II )with necessary connecting accessories Hundred Thirty

of same material at required depth in existing trench Seven and Paise

for laying of cable. below ground / road surface for Thirty Six Only

enclosing cable (D)120 mm outer dia.

estimated Tendered Rates

Item according to

but may be Item of work Unit

less in figures In Words quantities

Providing and erecting ISI marked PVC insulated PVC Rupees One

Sheathed Flat flexible Submersible copper cable Hundred Forty

approved make of following Size. (C) 3 Core x 4 Sq. Six and Paise

mm Forty Five Only

Providing & laying. R.C.C. Hume pipe for cable to be

laid 90 cm. below ground across the road crossing or

164 50.00 on floor with necessary material in an approved Mtr. 263.61

Three and Paise

manner and making the ground as per

original.(E)150 mm dia

Supplying & erecting earth pit of minimum bore

dia.150mm size approved make Earthing Electrode

consisting Pipe-in-Pipe Technology as per IS 3043-

1987 made of corrosion free hot dipped G.I.Pipes

having Outer pipe dia of 50mm having 80-200

Micron galvanising, Inner pipe dia of 25 mm having

200- 250 Micron galvanising, connection terminal dia

of 12mm with constant ohmic value surrounded by

highly conductive compound with high charge

dissipation suitable for following type of applications

with chamber and heavy duty cover.(approved make

OEM has to submit test certificate) & having back

165 2.00 Ea. 5760.03 Hundred Sixty

filling compound of (B) Inner chemical (CCM

and Paise Three

Compound)- Resistivity:- 0.2 • / meter testing as per

IEC 62561-2017, Voltage drop:- < 1 volt at no load &

dry form, Sulphar content:- <2%(C) Back fill

Compound :- Earthing compound should be capable

to retainmoisture for long time Necessary test report

must be submitted.(c) For Electrical Installation

covering Transformer Neutrals, Lightning arrester

Earthing, A.C.Plant & Sensitive Computer System(like

Automation, SCADA) i.e independent (b)For Electrical

installation up to 11 KV in normal soil. Length of Pipe

: 2.00 mtrs Back filling Compound :1 no. Bag of 25 Kg

estimated Tendered Rates

Item according to

but may be Item of work Unit

less in figures In Words quantities

Supplying & erecting earth pit of minimum bore

dia.150mm size approved make Earthing Electrode

consisting Pipe-in-Pipe Technology as per IS 3043-

1987 made of corrosion free hot dipped G.I.Pipes

having Outer pipe dia of 50mm having 80-200

Micron galvanising, Inner pipe dia of 25 mm having

200- 250 Micron galvanising, connection terminal dia

of 12mm with constant ohmic value surrounded by

highly conductive compound with high charge

dissipation suitable for following type of applications

with chamber and heavy duty cover.(approved make

OEM has to submit test certificate) & having back

filling compound of (B) Inner chemical (CCM

Compound)- Resistivity:- 0.2 • / meter testing as per

166 1.00 Ea. 8636.51 Hundred Thirty

IEC 62561-2017, Voltage drop:- < 1 volt at no load &

dry form, Sulphar content:- <2%(C) Back fill

Compound :- Earthing compound should be capable

to retainmoisture for long time Necessary test report

must be submitted.(c) For Electrical Installation

covering Transformer Neutrals, Lightning arrester

Earthing, A.C.Plant & Sensitive Computer System(like

Automation, SCADA) i.e independent (c) For

Electrical Installation covering Transformer Neutrals,

Lightning arrester Earthing, A.C.Plant & Sensitive

Computer System(like Automation, SCADA) i.e

independent Earthing in normal soil. Length of Pipe :

3.00 mtrs Back filling Compound :2 nos Bags of

Providing and erecting Pipe type earthing having

cms.long and 2.5 cms. dia. galvanised iron pipe with

167 4.00 coupling and buch buried in specially prepared earth Ea. 368.65

Eight and Paise

pit complete with necessary 8 SWG earth wire. - to

Sixty Five Only

be used for each Street Light

For using salt and charcoal / coke as required for Hundred Seventy

pipe type earthing. One and Paise

Providing one bag of 25 Kg. Additional Back Filling Hundred Seven

Compound (BFC) suitable for safe earthing device. and Paise Zero

Providing and erecting required size Copper strip for Hundred Ninety

170 10.00 earthing of H.T. OCB / ACB/ Transformer, LT panel Kg 794.87 Four and Paise

board, Motors etc. using copper clamp. Eighty Seven

Providing and erecting required size HOT deep Rupees Seventy

Galvanised iron strip for earthing of H.T. , OCB/ ACB/ Seven and Paise

Transformer LT panel board, Motors etc. using Seventy Seven

proper clamp. Only

estimated Tendered Rates

Item according to

but may be Item of work Unit

less in figures In Words quantities

Providing pair of rubber hand gloves suitable for

172 2.00 Ea 214.12 Fourteen and

working on 11 KV/22 KV supply.

Providing printed instruction chart both in English Hundred Thirty

173 2.00 and Gujarati and duly framed with front glasses, for Ea 130.29 and Paise

treatment of person suffering from Electric shock Twenty Nine

providng and erecting Approved make. energy meter

3 phase 4 wire unbalanced load 500 V.50A / 100A

174 1.00 Ea 2611.86 Hundred Eleven

complete erected as directed with necessary earth

and Paise Eighty

providng and erecting Suitable set of CTS for 100A

175 1.00 Ea 2105.85 Hundred Five

and Paise Eighty

Supplying rubber matting of following thickness as

176 12.00 Sq. Mtr 1027.17 Twenty Seven

per IS:15652/IEC 61111 (b)4mm

Supplying rubber matting of following thickness as Thousand Eighty

per IS:15652/IEC 61111 (c)12mm One and Paise

Providing & erecting L.T. Current Transformer with

Hundred Seventy

bar primary 50/5 to 1000/5 ratio 15 VA burden

178 3.00 Ea. 274.72 Four and Paise

erected in existing CRCA box duly secured with

insulating materials connected to the meter

Supplying and erecting approved make set of

indicator lamps of LED type lamp, lens cover, Bakelite

179 3.00 Ea. 43.43 Three and Paise

holder complete erected with necessary

Forty Three Only

Supplying and erecting approved make panel Rupees One

mounting type Digital Voltmeter having 3 digits LED Thousand Two

180 1.00 display, 0 to 750 AC Volts range erected on existing Ea. 1275.63 Hundred Seventy

panel board with all connection, wiring etc .with Five and Paise

manufacturers calibration certificate. Sixty Three Only

Supplying and erecting approved make panel

mounting type Digital Ammeter having 3 digits LED

display, external CT operated, calibrated for 0 to

181 1.00 Ea. 1558.43 Hundred Fifty

1000 Amps suitable to operate on 500 Volt AC

Eight and Paise

erected on existing panel board with all connection,

Forty Three Only

wiring etc .with manufacturers calibration certificate.

estimated Tendered Rates

Item according to

but may be Item of work Unit

less in figures In Words quantities

Providing & erecting capacitor duty contactor 3 Thousand Eight

182 1.00 phase, 415 V with proper connection for following Each 1820.02 Hundred Twenty

rating: (A) 10 KVAR and Paise Two

Design, Supplying, installing, testing of factory

fabricated ready made Three phase APFC Panel

Cubical Panel fabrication should be type tested as

per IEC 61921, 61439:1&2 Capacitor Duty Contactor

for switching as per following Steps Incomer Switch

of MCCB type Icu=Ics=50KA at 400/440 Volts, with

OC, SC, internal earth fault protection Incomer

Switch of MCCB type Icu=Ics=50KA at 400/440 Volts,

with OC, SC, internal earth fault protection,Copper

tinned insulated Busbar,Cubical panel should be

indoor type with IP 43 and IK 10,Metalized

183 1.00 Each 288878.18 Eight Hundred

polypropylene film tye3-phase 550Volt Capacitor,De

tuning Reactor for each capacitor,Panel having Short

Circuit and Overload protection,Each step Capacitor

having suitable MCB with Sc, OL, internal earth fault

relay,Each stage having Stage Contactor (Capacitor

load rating),PF regulator master controller having

suitable steps with LCD display, Rs

Communication port, Indication LED Lamps for main

incomer and ON-OFF for each capacitor bank,MS

Chanel for Floor mounting, Cable entry as per site

situation,Cooling fans for panel (C)100KVAR

Supplying & erecting approved make Power Factor

Meter 150mm dia flush/projection type/ balanced &

unbalanced load to work with appropriately provided

184 1.00 Ea. 5102.52 Hundred Two

CT’s 100/5A to 400/5A ratio & other accessories

and Paise Fifty

complete erected in M.S. box & connected to the

circuit by means of PVC copper Core leads.

Supplying & erecting ABC powder type 'Ceasefire'

185 10.00 type Fire extinguisher as per IS 13849 or 1 Kg No. 848.40

Eight and Paise

capacity with necessary clamp for erection on wall

Supplying & erecting carbon dioxide (CO2) fire Rupees Six

extinguisher user of following capacity with Thousand Five

186 10.00 necessary clamps made from 50 x 6 mm M.S. Flat No. 6591.26 Hundred Ninety

with nut & bolts grouted in wall complete. [A] For 4.5 One and Paise

Kg Capacity Twenty Six Only

Supplying stand first AID box with antiseptic cream,

medicine for use on wounds due burn, crepe Rupees Three

bandage, gauge bandage, medicated ready to use Hundred Fifty

bandage (Band-aid) adhesive tape for medicinal user, Three and Paise

Scissors, anti-septic solution (Savlon or similar) etc. Fifty Only

(All above contents shall be of standard makes)

estimated Tendered Rates

Item according to

but may be Item of work Unit

less in figures In Words quantities

S.I.T.C. of single phase submersible pump set

suitable for 100 mm size or more dia bore well Rupees Fifteen

having motor capacity and discharge as under with Thousand Five

188 1.00 necessary panel box. Lifting and Lowering taken Ea. 15595.41 Hundred Ninety

extra.(a) Motor rating 1 HP (12 stage) pump having Five and Paise

capacity of 50 LPM at 43 to 45 mtr head suitable for Forty One Only

32 mm dia. delivery pipe CAT-III

Providing & erecting open well type horizontal mono

block pump set with stainless steel body having

following specification (A) 0.5 H.P. single phase open

189 1.00 Ea. 7934.56 Hundred Thirty

well motor pump set having discharge of 115 LPM @

15 mtr. head suitable for 32 mm dia. delivery pipe

with control panel Cat. II

Supplying & erecting approved make motor control

cubical panel [Star delta] made from 16G CRCA sheet

duly epoxy powder painted inside and outside with

hinged doors and locking with suitable size of ON -

OFF isolator (AC 3 / 23 duty) main fuses. Digital volt

and current meter (in a single unit) with micro

controller based control unit and current sensing

single phasing preventer electronic overload Rupees Seven

protection, over voltage (Programmable) protection Thousand Two

and under voltage (Programmable) protection, Hundred Fifty

prodless dry run protection programming facility for and Paise

setting of all parameter like overload current, high Seventy Nine

voltage limit, low voltage limit, dry run limit with Only

digital indication on seven segment LED display for

any fault like over load, high voltage, low voltage, dry

running single crimped, electronic star delta timer,

feather touch start / stop push buttons to be erected

on angle iron frame. Grouted on wall the contactors

will be of L& T, Siemens, BCH make only) (a) DOL up

Supplying & erecting approved make Automatic

liquid level controller 6A.as per instruction of Rupees Two

Engineer in charge on site complete with wiring Thousand Three

191 1.00 connection with existing wires , with copper Ea 2355.32 Hundred Fifty

conductor from pump to upper and lower tank.(Size Five and Paise

Not less than 1.5 Sq MM) from pump to upper and Thirty Two Only

lower tank with ISI marked Rigid PVC Pipe.

estimated Tendered Rates

Item according to

but may be Item of work Unit

less in figures In Words quantities

Supplying and erecting approved make Octagonal

pole made from HR sheet steel. The pole should be

made as per IS. and shall be coated with hot dip

galvanizing as per IS 2629/2633/4759, suitable

suspend local wind speed with integral Junction box

consist of terminal plate of min 6mm Hylam sheet, Rupees Fifteen

standard profile 35mmX7.5mm Din-Rail for MCB Thousand Seven

192 4.00 Mounting, stud type terminal and arrangement for Ea. 15705.50 Hundred Five

cable termination to be erected With Suitable and Paise Fifty

foundation (Included) as per details given by Only

manufacturer considering site requirement. (H)

Mtr. Long 70 mm Top X 155 mm bottom dia, 3 mm

thickness with 260mmX260mmX16mm base plate, 4-

M24 Bolts and 750mm long with necessary G.I. J

Bolts .Approx Pole weight 97 kg

Providing and erecting Street Light pole bracket

comprising main B Class MS pipe of 4.2 cm/require

outside dia. complete with suitable B Class M.S.

sleeve tubing of approx. 45cms.length and suitable

for 76.5 mm /80mm / required size of pole top Rupees Six

having sufficient fasteners for fixing the brackets and Hundred Twenty

having spread of 1.5.mtr. length with 110 deg.with Six and Paise

vertical plane & suitable welded stays, reducer and Twenty Only

with check nuts complete painted with one coat of

Red oxide / PU base primer and two coats of

Aluminium / PU paint. paint with following nos of

arms [A] Single Arm Bracket 1.5 Mtr

Providing and erecting Street Light pole bracket

comprising main B Class MS pipe of 4.2 cm/require

outside dia. complete with suitable B Class M.S.

sleeve tubing of approx. 45cms.length and suitable

for 76.5 mm /80mm / required size of pole top Rupees Nine

having sufficient fasteners for fixing the brackets and Hundred Sixteen

having spread of 1.5.mtr. length with 110 deg.with and Paise Seven

vertical plane & suitable welded stays, reducer and Only

with check nuts complete painted with one coat of

Red oxide / PU base primer and two coats of

Aluminium / PU paint. paint with following nos of

arms [B] Double Arm Bracket 1.5 Mtr

Supplying & erecting approved make SMC press

moulded composite FRP . loop-in, loopout approx.

2mm thick box complete with Bakelite connector

strip 5way(3P+N+E),DIN rail for mounting mob &

195 4.00 hinged doors as per requirement having locking Ea 898.90

Eight and Paise

arrangements with mounting clamp with nuts, bolts

& washers suitable for erection on pole with cable

clamps& earth bolt of following size of box.(a)

300mm x 200mm x 100mm [deep]

estimated Tendered Rates

Item according to

but may be Item of work Unit

less in figures In Words quantities

Providing and erecting iron clad cable route marker Rupees Two

duly marked with ELE.CABLE of size 23 cm.X 12 cm. Hundred Forty

Flushed with ground in cement foundation as and Paise Thirty

directed by Engineer in charge. Eight Only

Supplying and erecting B class Galvanized iron pipe Rupees One

having smooth finished bore of the pipe on both Hundred Eighty

197 10.00 ends erected nuts and bolts along the pole / wall Mtr. 180.79 and Paise

shaping the pipe as per site requirement. Pipe dia as Seventy Nine

following.(a) 25 mm dia Only

Supplying and erecting LED street light / Flood light

fittings with High power White LEDs wattage of

1Watt and above assembled on single MCPCB,

efficiency more than 130 lm/w and corrosion free

High pressure die cast aluminum housing with

smooth finish powder coated and heat sink extruded

aluminium with diffuser and Polycarbonate optics/

lenses with company mark/name engraved or

embossed 120 to 300 V,Power Factor more than

0.95, THD < 10 %, CCT 3000 K to 5700K, Uniformity

ratio >0.45, Luminaire efficacy> 100 lumens/watt .

198 4.00 Ea 4997.48 Hundred Ninety

LED driver efficiency > 85 %.CREE /OSRAM / PHILIPS

Seven and Paise

Lumileds / NICHIA / SEOUL/ BridgeLux (U.S.A.) make

Forty Eight Only

LED used for luminaire. ( fittings required LM-79 &

LM-80 certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED fittings.The

Engineer incharge may select any wattage capacity

between the ranges shown.) (A) Street Light (IP-65),

Surge protection - 4KV integral and 10 kv non

integral ,Light must have 440VAC line supply

protection. It should withstand 48 hours for 440VAC

line supply.(e) above 48 to 60 Watts Cat-lll

estimated Tendered Rates

Item according to

but may be Item of work Unit

less in figures In Words quantities

Supplying and erecting LED street light / Flood light

fittings with High power White LEDs wattage of

1Watt and above assembled on single MCPCB,

efficiency more than 130 lm/w and corrosion free

High pressure die cast aluminum housing with

smooth finish powder coated and heat sink extruded

aluminium with diffuser and Polycarbonate optics/

lenses with company mark/name engraved or

embossed 120 to 300 V,Power Factor more than Rupees Six

0.95, THD < 10 %, CCT 3000 K to 5700K, Uniformity Thousand Eighty

199 4.00 ratio >0.45, Luminaire efficacy> 100 lumens/watt . Ea 6088.28 Eight and Paise

LED driver efficiency > 85 %.CREE /OSRAM / PHILIPS Twenty Eight

Lumileds / NICHIA / SEOUL/ BridgeLux (U.S.A.) make Only

LED used for luminaire. ( fittings required LM-79 &

LM-80 certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED fittings.The

Engineer incharge may select any wattage capacity

between the ranges shown.) (B) Flood Light (IP-65),

Surge protection -4KV integral and ,Light must have

440VAC line supply with over-voltage protection. (iii)

Above 60 to 90 watts Cat-lll

Supplying & erecting approved make Digital time

switch having lithium cell 6 years operative and

operate battery backup 1 channel day clock with

memory programme, suitable to operate on 240V +

5%, 16A with, floating contacts Minimum switching

200 1.00 setup time 1 minimum & LCD display. Also Ea 3168.37

Eight and Paise

comprised permanent ON/OFF switching.

Programming switches & housed in fire proof

thermoplastic enclosure & transparent cover erected

as required with necessary connection erected as

Supply of Fibreglass Platform Step (A Type) Ladder -

18 FT having following specifications : It should have Rupees Thirty

large fully serrated platform 15” wide 20” deep Three Thousand

201 1.00 which locks ladder , Aluminium feet with thick Ea. 33895.60 Eight Hundred

rubber tread, top rail guard to serve as a railing, two Ninety Five and

pairs of gusset support at the bottom step and All Paise Sixty Only

gussets are heavy duty steel. Capacity : 300 lbs.

202 2.00 Providing & fixing 2 MP IP Dome Camera Nos. 3219.00 Hundred

203 4.00 Providing & fixing 2 MP IP Bullet Camera Nos. 3119.00 Hundred

estimated Tendered Rates

Item according to

but may be Item of work Unit

less in figures In Words quantities

204 1.00 Providing & fixing 8 ch NVR Nos. 8145.00 Hundred Forty

205 1.00 Providing & fixing 2 TB Hard Disk Nos. 3260.00 Hundred Sixty

206 1.00 Providing & fixing 08 Port POE switch Nos. 4699.00 Hundred Ninety

Providing & fixing Cat-6 Dual Sheath PVC & LSZH Anti-

207 400.00 Mtr 85.00 Five and Paise

208 6.00 Providing & fixing Back Box with IO at camera side Nos. 455.00

Rupees Fifty Two

209 400.00 Providing & fixing 25 MM PVC Pipe Mtr 52.00 and Paise Zero

210 1.00 Providing & fixing 55 inch display Nos. 25930.00 Nine Hundred

Thirty and Paise

Total Amount Rs.

Total Amount Rs.