ADDN/ALTN OF THE PERIMETER WALL OF RAMGARH MIL STN UNDER GE RAMGARH CANTT

Amount

Refer Drawing No.CEJZ/TD/ST/896,Sheet No. 1/1 Excavation in trenches in any type of soil not exceeding 1.5 metre deep and not exceeding 1.5 mtr width and getting out soil including forming bottom surface to required slope/gradient for laying cables/pipes,foundations,laying of cable, shafts, well, cesspits, manholes etc. complete all as specified and directed.

Excavation in trenches in any type of soil exceeding 1.5 metre but not exceeding 3.0 metre deep and not exceeding 1.5 mtr width and getting out soil including forming bottom surface to required slope/gradient for laying cables/pipes,foundations,laying of cable, shafts, well, cesspits, manholes etc. complete all as specified and directed.

Returning, filling in including spreading, leveling, watering and well ramming in layers of not exceeding 25 cm thick after the cables & pipes etc. are laid, jointed & tested and foundations complete all as specified and directed by Engineer-in-Charge.

Removal of surplus excavated soil exceeding 50 Mtr distance and depositing where directed by Engineer-in-Charge at a level not exceeding 1.5 m above the starting point complete all as specified.

M&L for plain cement concrete 1:4:8 ,type D-2 (using 40 mm graded crushed stone aggregate) as in foundations, filling & mass concrete for fencing posts, foundation of pole ,struts & stay assembly etc complete all as specified and directed.

Demolition of brick work of any description and in any position built in cement or cement lime mortar including all quoins, arches, pillars including segregation of serviceable bricks for reuse & removal of rubbish out off from site etc complete all as specified and directed

M&L for fly ash brick work using old size bricks, straight or curved on plan exceeding 6.0 m mean radius, built in cement mortar 1:6 etc complete all as specified & directed.

M&L for rendering 15 mm thick on fair face brick masonry/concrete surface etc in cement mortar (1:6) surface finished even & smooth without using extra cement complete all as specified and directed.

Use & waste form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams, and similar work vertical or to batter for rough finished surfaces of concrete complete all as specified and directed.

Use and waste of form work to sides and soffit of lintel ,Beam, floor /roof Beams, cantilevers, bressummers, etc for rough finished surface of concrete complete all as specified and directed.

Use & waste form work to sieds of pillars, posts, struts columns etc for rough finished or flat surfaces of concrete, complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over grade Fe-500, cut to length, bent to shape required, including cranking bending spirally for hooping for column,, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete etc all as specified and directed.

M&L for mild steel TMT bars 08 mm dia and over grade Fe -500 , as in reinforcement ,cut to length, bent to shape required, including cranking bending spirally for hooping for column,, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete etc all as specified and directed.

M&L reinforced cement concrete M-25 (design mix) (using 20 mm graded crushed stone aggregate) as in foundation including rafts, footings,plinth beams, and mass concrete etc.complete all as specified and directed. Note : Reinforcement & form work will be measured & paid seperately under respective item of BOQ.

M&L reinforced cement concrete M-25 (design mix) (using 20 mm graded crushed stone aggregate) as in coloumns, pillars, piers,post and struts etc.complete all as specified and directed. Note : Reinforcement & form work will be measured & paid seperately under respective item of BOQ.

M&L reinforced cement concrete M-25 (design mix) (using 20 mm graded crushed stone aggregate) as in lintels beam, floor/roof Beams, cantilevers, bressummers, etc complete all as specified and directed. Note : Reinforcement & form work will be measured & paid seperately under respective item of BOQ.

M&L for preparation of new plastered surfaces of walls/chajja /lintel and applying two coats of cement based paint (white or tinted )over a coat of alkali resistant primer complete as specified and directed.

M&L for mild steel works in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc, flat iron fillets (for securing wire mesh etc) including all necessary drilling, bilting or reverting etc similar work conforming to Fe-290 grade E-165 all as specified and direcrted.

M&L for prepartion of new or previously untreated steel surface of any description , not otherwise described over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified & directed.

S & F for galvanised 2 strand steel barbed wire 2.24 mm dia barbed with 2mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossing with and provision of galvanised mild steel wire, staples or steel pins, etc., complete all as specified and as directed. Note:Each line wire to be measured.

S & F for CONSEC-ZAL Super Razor unched barb tape concertina coil confirming preferably to IS: 278:2009, with electrogalvanised as per IS: 12753:1989(helix coil with and including necessary GI fixing clips for securing complete all as specified and directed with as per specification fixed on the 'Y' or 'U' shape of MS angle :- (i) Dia of coil (when unstretched)-610 mm (ii)Nos of Spiral- 6 Spirals per RM (iii)Weight of each coil with hessian pack -8.50 kg (+0.50) (iv)Central core wire -made from 2.60 mm dia GI-H.T.S.S wire as per IS -4454 galvanised as per IS-2629 (v)Coverage per coil-8 RM (Maximum) (vi)Razor Punched Strip-Razor Punched Tape is CONSEC-ZAL steel confirming to ASTM A-792/A-792M with additional primer treatment of Epoxy/Polyurethane and final paint paint top coat of Caulfield green shade (BSL 139) by hot dipping processes. Note:-Running length of the security wall/fencing shall be measured and paid above item.

M/S CHAUHAN CONSTRUCTION (BID ID -3267372)

M/S KAMLESHWAR SINGH (BID ID -3272098)

Modernage Constructions Pvt. Ltd. (BID ID -3271000)

simplex infra project (BID ID -3267230)

M/S DEEPAK KUMAR SINHA (BID ID -3267244)

upadhyay engineers and consultant (BID ID -3267513)

M/s Manoj Kumar Gope (BID ID -3266743)

M/s Ramgarh Raj Construction Pvt Ltd (BID ID -3267549)

ganpati enterprises (BID ID -3267512)