Construction of 2 storied library reading room and common room at Munshi Singh College, Motihari, Bihar

SUMMARY OF BILL OF QUANTITY

S. NO SUB HEAD DSR-Amount NDSR Amount Total Amount

S. NO SUB HEAD DSR-Amount NDSR Amount Total Amount

2 Plumbing work & water supply ₹ 560,661.10 ₹ 11,859.60 ₹ 572,520.70

3 Electrical work & Fire Fighting work ₹ 1,017,265.49 ₹ 931,109.89 ₹ 1,948,375.38

Name of work- “Construction of 2 storied Library reading room & common room at Munshi Singh College, Motihari

BILL OF QUANTITY

ITEM DSR DSR NDSR NDSR

S. NO DESCRIPTION OF ITEMS UNIT QTY

CODE-DSR RATE AMOUNT RATE AMOUNT

Earth work in excavation by mechanical means (Hydraulic

excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in

1 2.6 width as well as 10 sqm on plan) including getting out and disposal of

excavated earth lead upto 50 m and lift upto 1.5 m, as directed by

Engineer-in-charge.

2.6.1 All kinds of soils Cum 450.00 177.50 79875.00

Extra for every additional lift of 1.5 m or part thereof in excavation / banking

excavated or stacked materials.

2.26.1 All kinds of soil Cum 225.00 126.80 28530.00

Digitally signed by PRIYA

ITEM DSR DSR NDSR NDSR

S. NO DESCRIPTION OF ITEMS UNIT QTY

CODE-DSR RATE AMOUNT RATE AMOUNT

Filling available excavated earth (excluding rock) in trenches, plinth, sides of

foundations etc. in layers not exceeding 20cm in depth, consolidating

each deposited layer by ramming and watering, lead

up to 50 m and lift upto 1.5 m.

Supplying and filling in plinth with sand under floors, including

watering, ramming, consolidating and dressing complete.

Surface dressing of the ground including removing vegetation and

5 2.28 inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50

m and lift up to 1.5 m.

2.28.1 All kinds of soil Sqm 100.00 34.15 3415.00

Supplying chemical emulsion in sealed containers including delivery as

2.34.1 Chlorpyriphos/ Lindane emulsifiable concentrate of 20% Litre 100.00 234.75 23475.00

Anti termite treatment

Diluting and injecting chemical emulsion for POST-

7 2.35 CONSTRUCTIONAL anti-termite treatment (excluding the cost of

chemical emulsion) :

Along external wall where the apron is not provided using chemical emulsion

@ 7.5 litres / sqm of the vertical surface of the substructure to a depth of

300mm including excavation channel along the wall & rodding etc. complete:

With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration

Treatment of soil under existing floors using chemical emulsion @ one

litre per hole, 300 mm apart including drilling 12 mm diameter holes and

plugging with cement mortar 1 :2 (1 cement : 2 Coarse

sand) to match the existing floor:

2.35.3.1 With Chlorpyriphos/Lindane E.C. 20% with 1% concentration Sqm 144.00 310.05 44647.20

Digitally signed by PRIYA

ITEM DSR DSR NDSR NDSR

S. NO DESCRIPTION OF ITEMS UNIT QTY

CODE-DSR RATE AMOUNT RATE AMOUNT

Treatment at points of contact of wood work by chemical emulsion

Chlorpyriphos/ Lindane (in oil or kerosene based solution) @ 0.5 litres

per hole by drilling 6 mm dia holes at downward angle of 45 degree at

150 mm centre to centre and sealing the same.

4.0 CONCRETE WORKS

Providing and laying in position cement concrete of specified grade excluding

the cost of centering and shuttering - All work up to plinth level :

1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm

Centering and shuttering including strutting, propping etc. And

removal of form work for :

4.3.1 Foundations, footings, bases for columns. Sqm 100.37 392.15 39360.10

Providing and laying damp-proof course 40mm thick with cement concrete

13 4.10 1:2:4 (1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 12.5mm Sqm 25.00 410.85 10271.25

Extra for providing and mixing water proofing material in cement concrete Per 50 kg

work in doses by weight of cement as per manufacturer's specification. cement

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement

: 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size)

15 4.17 over 75mm thick bed of dry brick ballast 40 mm nominal size, well Sqm 50.00 749.30 37465.00

rammed and consolidated and grouted with fine sand, including

necessary excavation, levelling & dressing & finishing the top smooth.

5.0 REINFORCED CEMENT CONCRETE WORK

Centering and shuttering including strutting, propping etc. And

removal of form for :

5.9.1 Foundations, footings, bases of columns, etc. for mass concrete. Sqm 93.38 392.15 36617.99

Digitally signed by PRIYA

ITEM DSR DSR NDSR NDSR

S. NO DESCRIPTION OF ITEMS UNIT QTY

CODE-DSR RATE AMOUNT RATE AMOUNT

Walls (any thickness) including attached pilasters, butteresses, plinth and

string courses etc.

5.9.3 Suspended floors, roofs, landings, balconies and access platform. Sqm 348.50 927.25 323146.63

5.9.4 Shelves (Cast in situ) Sqm

5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers Sqm 272.15 736.40 200413.47

5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts. Sqm 294.27 961.30 282876.94

5.9.7 Stairs, (excluding landings) except spiral-staircases. Sqm 33.19 764.95 25390.22

Small lintels not exceeding 1.5m clear span, moulding as in cornices, window

5.9.15 sills, string courses, bands, copings, bed plates, anchor blocks and the Sqm 40.45 392.15 15864.04

5.9.16 Edges of slabs and breaks in floors and walls

5.9.19 Weather shade, Chajjas, corbels etc., including edges. Sqm 26.48 951.10 25187.98

Steel reinforcement for R.C.C. work including straightening, cutting, bending,

placing in position and binding all complete upto plinth level.

5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. Kg 11356.42 107.85 1224789.37

Steel reinforcement for R.C.C. work including straightening, cutting, bending,

placing in position and binding all complete above plinth level.

5.22A.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. Kg 15603.65 107.85 1682853.46

Providing and laying in position machine batched and machine mixed

design mix M-25 grade cement concrete for reinforced cement

concrete work, using cement content as per approved design mix, including

pumping of concrete to site of laying but excluding the cost of

centering, shuttering, finishing and reinforcement, including admixtures

in recommended proportions as per IS: 9103 to accelerate, retard setting of

concrete, improve workability without impairing strength and durability

as per direction of Engineer-in- charge. (Note :- Cement content

considered in this item is @ 330 kg/cum. Excess/ less cement used

as per design mix is payable/recoverable separately).

Digitally signed by PRIYA

ITEM DSR DSR NDSR NDSR

S. NO DESCRIPTION OF ITEMS UNIT QTY

CODE-DSR RATE AMOUNT RATE AMOUNT

5.33.1.1 All works upto plinth level. Cum 81.12 9504.75 770999.19

5.33.2.1 All works above plinth level upto floor V level. Cum 111.45 9860.40 1098987.23

6.0 BRICK WORK

Brick work with common burnt clay F.P.S. (non modular) bricks of class

designation 7.5 in foundation and plinth in:

6.1.2 Cement mortar 1:6 (1 cement : 6 coarse sand) Cum 14.47 7132.25 103190.1954

Brick work with common burnt clay F.P.S. (non modular) bricks of class

21 6.4 designation 7.5 in superstructure above plinth level up to floor V level in all

shapes and sizes in :

6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand) Cum 111.06 9105.95 1011340.727

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of

class designation 7.5 in foundations and plinth in :

6.12.2 Cement mortar 1:4 (1 cement : 4 coarse sand) Sqm 25.00 905.05 22626.25

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of

23 6.13 class

designation 7.5 in superstructure above plinth level up to floor V level.

6.13.2 Cement mortar 1:4 (1 cement : 4 coarse sand) Sqm 69.72 1123.80 78347.40

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at

every third course of half brick masonry.

8 & 11 Flooring Work & Granite work

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed

with grey cement slurry mixed with pigment to match the shadeof the slab,

25 11.26 including rubbing and polishing complete with base of cement mortar 1 : 4 (1

cement : 4 coarse sand) :

Digitally signed by PRIYA

ITEM DSR DSR NDSR NDSR

S. NO DESCRIPTION OF ITEMS UNIT QTY

CODE-DSR RATE AMOUNT RATE AMOUNT

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid

on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and

jointed with grey cement slurry mixed with pigment to match the shade of the

slabs, including rubbing and polishing complete

Providing and laying Ceramic glazed floor tiles of size 300x300 mm(thickness

to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of

approved make in colours such as White, Ivory, Grey,Fume Red Brown, laid

on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), Jointing with

grey cement slurry @ 3.3 kg/sqm including pointing the joints with white

cement and matching pigment etc.,complete.

Providing & Laying vitrified floor tiles in different sizes ( thickness to

be specified by the manufacturer) with water absorption's less than

0.08% and confirming to IS : 15622 of approved make in all colours and

shades, laid on 20mm thick cement mortar 1:4 (1 cement

: 4 coarse sand) including grouting the joints with white cement and matching

pigments etc, complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS:

15622 (thickness to be specified by the manufacturer), of approved make, in

all colours, shades except burgundy, bottle green, black ofany size as

approved by Engineer-in-Charge, in skirting, risers of stepsand dados, over

12 mm thick bed of cement mortar 1:3 (1 cement : 3coarse sand) and jointing

with grey cement slurry @ 3.3kg per sqm,including pointing in white cement

mixed with pigment of matching shade

Digitally signed by PRIYA

ITEM DSR DSR NDSR NDSR

S. NO DESCRIPTION OF ITEMS UNIT QTY

CODE-DSR RATE AMOUNT RATE AMOUNT

Providing and fixing 18mm thick gang saw cut ( premoulded and

prepolished) machine cut for kitchen platforms, vanity counters, window

sills , facias and similar locations of required size of approved

shade, colour and texture laid over 20mm thick base cement mortar

1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed

with matching pigment, epoxy touch ups, including rubbing, curing,

moulding and polishing to edge to give high gloss finish etc. complete at

8.2.2 Granite of any colour and shade

8.2.2.2 Area of slab over 0.50 sqm SQM 2.30 5136.30 11813.49

Providing edge moulding to 18 mm thick marble stone counters,

31 8.3 Vanities etc., including machine polishing to edge to give high gloss finish etc.

complete as per design approved by Engineer-in-Charge.

8.3.2 Granite work metre 10.00 510.95 5109.50

9.0 WOOD & PVC WORK

Providing wood work in frames of doors, windows, clerestory windows and

other frames, wrought framed and fixed in position with hold fast lugs or

with dash fasteners of required dia & length (hold fast lugs or dash fastener

shall be paid for separately).

9.1.1 Second class teak wood Cum 2.50 142949.70 357374.25

Providing and fixing ISI marked flush door shutters conforming to IS :

2202 (Part I) non-decorative type, core of block board

33 9.21 construction with frame of 1st class hard wood and well matched

commercial 3 ply veneering with vertical grains or cross bands and

face veneers on both faces of shutters:

35 mm thick including ISI marked Stainless Steel butt hinges with

necessary screws

Digitally signed by PRIYA

ITEM DSR DSR NDSR NDSR

S. NO DESCRIPTION OF ITEMS UNIT QTY

CODE-DSR RATE AMOUNT RATE AMOUNT

Extra for providing lipping with 2nd class teak wood battens 25 mm

34 9.23 minimum depth on all edges of flush door shutters (over all area of door Sqm 40.00 462.35 18494.00

shutter to be measured).

Providing and fixing M.S. grills of required pattern in frames of

35 9.48 windows etc. with M.S. flats, square or round bars etc. including

priming coat with approved steel primer all complete.

9.48.2 Fixed to openings /wooden frames with rawl plugs screws etc. KG 430.56 238.35 102623.98

Providing and fixing aluminium sliding door bolts, ISI marked anodised

36 9.96 (anodic coating not less than grade AC 10 as per IS : 1868), transparent or

dyed to required colour or shade, with nuts and screws etc. complete :

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic

37 9.97 coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to

required colour or shade, with necessary screws etc. complete :

Providing and fixing aluminium handles, ISI marked, anodised (anodic

38 9.100 coating not less than grade AC 10 as per IS : 1868) transparent or dyed to

required colour or shade, with necessary screws etc. complete :

Providing and fixing aluminium hanging floor door stopper, ISI marked,

anodised (anodic coating not less than grade AC 10 as per IS : 1868)

transparent or dyed to required colour and shade, with necessary screws etc.

9.101.1 Single Rubber stopper each 24 39.6 950.40

Providing & Fixing decorative high pressure laminated sheet of plain /

wood grain in gloss / matt / suede finish with high density protective surface

layer and reverse side of adhesive bonding quality conforming to IS :

2046 Type S, including cost of adhesive of approved quality.

Digitally signed by PRIYA

ITEM DSR DSR NDSR NDSR

S. NO DESCRIPTION OF ITEMS UNIT QTY

CODE-DSR RATE AMOUNT RATE AMOUNT

Providing and fixing factory made uPVC door frame made of uPVC extruded

sections having an overall dimension as below (tolerance ±1mm), with wall

thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with

galvanized brackets and stainless steel screws, joints mitred and Plastic

welded. The hinge side vertical of the frames reinforced by galvanized M.S.

tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos.

stainless steel hinges fixed to the frame complete as per manufacturer’s

specification and direction of Engineer- in-charge

9.117.1 Extruded section profile size 48x40 mm meter 30.00 270.20 8106.00

42 9.118 Providing and fixing to existing door frames.

24 mm thick factory made PVC door shutters made of styles and rails of a

uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm)

with inbuilt edging on both sides. The styles and rails mitred and joint at the

corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm

having wall thickness 1.0 mm and stainless steel screws. The styles of the

shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1

mm (± 0.1 mm) wall thickness. The lock rail made up of ‘H’ section, a uPVC

9.118.1 hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed sqm 25 2969.25 ₹ 74,231.25

to the shutter styles by means of plastic/galvanised M.S. ‘U’ cleats. The

shutter frame filled with a uPVC multi-chambered single panel of size not less

than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall

thickness. The panels filled vertically and tie bar at two places by inserting

horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers,

complete as per manufacturer’s specification and direction of Engineer-in-

charge. (For W.C. and bathroom door shutter)

Digitally signed by PRIYA

ITEM DSR DSR NDSR NDSR

S. NO DESCRIPTION OF ITEMS UNIT QTY

CODE-DSR RATE AMOUNT RATE AMOUNT

Providing and fixing factory made uPVC glazed/wire mesh windows/doors

comprising of lead free uPVC multi-chambered frame, sash and

mullion/coupler (where ever required) extruded profiles having minimum

wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series

R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design

duly reinforced with galvanized mild steel section made of required shape &

size as per CPWD Specification, uPVC extruded glazing beads, interlocks and

Inline sash adaptor (where ever required) of appropriate dimension, EPDM

gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with

countersunk head, comprising of matching polyamide PA6 grade sleeve for

fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers,

plastic caps and necessary stainless steel screws etc. Profile of frame, sash &

mullion (if required) shall be mitred cut and fusion welded/mechanically

jointed duly sealed at all corners, including drilling of holes for fixing

hardware and drainage of water etc. After fixing frame the gap between

frame and adjacent finished wall shall be filled with weather proof silicon

sealant over backer rod of approved size and quality, all complete as per

approved drawing conforming to CPWD specification & direction of

Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC

profiles to be as per design approved by Engineer-in-Charge. Wire mesh /

Glazing of plain/ toughened/ laminated/ double glass unit with / without

high performance coatings as per design requirements and conforming to IS:

3548 & IS: 16231 shall be paid separately. Note:- Structural design proof

checked from a Government Engineering Institute, to be provided by the

manufacturer for : (i) Sites with basic wind speed > 45 m/sec as per IS 875 –

Part 3 (ii) Sites with structure height more than 20m for all wind speeds

Three track three panels sliding window with two glazed & one wire mesh

9.147A4 panels with Aluminium channel for roller track, wool pile, nylon rollers with

Using R2 series with frame (70mm & above) x (40mm & above) & both glazed

9.147A4.1 and fly screen sash (25mm & above) x (50mm & above) with zinc alloy Sqm 75 10993.55 ₹ 824,516.25

(zamak) powder coated touch locks with hook. (Height upto 1.2 metre)

Digitally signed by PRIYA

ITEM DSR DSR NDSR NDSR

S. NO DESCRIPTION OF ITEMS UNIT QTY

CODE-DSR RATE AMOUNT RATE AMOUNT

10.0 STEEL WORK

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for

ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm

thick M.S. sheet with its top surface hacked for proper bonding, top lid

shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm

dia round headed screws, one lock at the corners. Clamp shall be made of

12 mm dia M.S. bar bent to shape as per standard drawing.

Steel work welded in built up sections/ framed work, including cutting,

45 10.25 hoisting, fixing in position and applying a priming coat of approved steel

primer using structural steel etc. as required

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar

Providing and fixing stainless steel ( Grade 304) railing made of Hollow

tubes, channels, plates etc., including welding, grinding, buffing, polishing

and making curvature (wherever required) and fitting the same with

necessary stainless steel nuts and bolts complete, i/c fixing the railing with

46 10.28 necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., Kg 300.00 772.40 231720.00

of required size, on the top of the floor or the side of waist slab with suitable

arrangement as per approval of Engineer-incharge, (for payment purpose

only weight of stainless steel members shall be considered excluding fixing

accessories such as nuts, bolts,fasteners etc.)

Making khurras 45x45 cm with average minimum thickness of 5 cm cement

concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20

47 12.22 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 each 6.00 298.25 1789.50

mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat

cement, rounding the edges and making and finishing the outlet complete.

Digitally signed by PRIYA

ITEM DSR DSR NDSR NDSR

S. NO DESCRIPTION OF ITEMS UNIT QTY

CODE-DSR RATE AMOUNT RATE AMOUNT

Providing and fixing on wall face unplasticised Rigid PVC RAIN

WATER PIPES conforming to IS : 13592 Type A including jointing with

seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.(i)

Single socketed pipes.

Providing and fixing on wall face unplasticised - PVC moulded fittings/

accessories for unplasticised Rigid PVC rain water pipes conforming to

IS : 13592 Type A including jointing with seal ring conforming to IS :

5382 leaving 10 mm gap for thermal expansion.

12.42.1 Coupler

12.42.6 Shoe (Plain)

Providing and laying brick tiles over mumty roofs, grouted with cement

mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing

compound by weight of cement, over 12 mm layer of cement mortar 1:3 (1

cement : 3 fine sand) and finished neat: With common burnt clay

F.P.S. (non modular) brick tiles of class

designation 10.

13.0 FINISHING WORK

51 13.4 12 mm cement plaster of mix :

15 mm cement plaster on rough side of single or half brick wall of mix

Add or deduct for plaster drip course/ groove in or moulding to R.C.C.

projections.plastered surface

54 13.16 6 mm cement plaster of mix :

Digitally signed by PRIYA

ITEM DSR DSR NDSR NDSR

S. NO DESCRIPTION OF ITEMS UNIT QTY

CODE-DSR RATE AMOUNT RATE AMOUNT

Extra for providing and mixing water proofing material in cement

plaster work in proportion recommended by the manufacturers.

56 13.114 Melamine polishing on wood work (one or more coat). SQM 136.24 1192.30 16123.41

Providing and applying white cement based putty of average

thickness 1 mm, of approved brand and manufacturer, over the

plastered wall surface to prepare the surface even and smooth

58 13.46 Finishing walls with Acrylic Smooth exterior paint of required shade :

New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including

priming coat of exterior primer applied @ 2.20 kg/10 sqm)

60 13.37 White washing with lime to give an even shade :

13.37.1 New work (three or more coats) SQM 200.00 39.05 7810.00

Distempering with oil bound washable distemper of approved brand and

manufacture to give an even shade :

New work (two or more coats) over and including water thinnable priming

coat with cement primer

62 13.50 Applying priming coat:

Using R2 series with frame (70mm & above) x (40mm & above) & both glazed

13.50.2 and fly screen sash (25mm & above) x (50mm & above) with zinc alloy SQM 56.70 74.65 4232.66

(zamak) powder coated touch locks with hook. (Height upto 1.2 metre)

With ready mixed red oxide zinc chromate primer of approved brand and

13.50.3 manufacture on steel galvanised iron/ SQM 84.00 67.40 5661.60

21.0 ALUMINIUM WORK

Digitally signed by PRIYA

ITEM DSR DSR NDSR NDSR

S. NO DESCRIPTION OF ITEMS UNIT QTY

CODE-DSR RATE AMOUNT RATE AMOUNT

Providing and fixing aluminium work for doors, windows, ventilators and partitions

with extruded built up standard tubular sections/ appropriate Z sections and other

sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash

fasteners of required dia and size, including necessary filling up the gaps at junctions,

i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc.

Aluminium sections shall be smooth, rust free, straight, mitred and jointed

mechanically wherever required including cleat angle, Aluminium snap beading for

glazing / paneling, C.P. brass / stainless steel screws, all complete as per

architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling

and dash fasteners to be paid for separately)

21.1.1 For fixed portion

21.1.1.2 Powder coated aluminium (minimum thickness of powder coating 50 micron) kg 60.00 530.9 ₹ 31,854.00

Providing and fixing glazing in aluminium door, window, ventilator shutters and

partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the

architectural drawings and the directions of engineer-in-charge . (Cost of aluminium

snap beading shall be paid in basic item):

21.3.1 With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) sqm 10.00 1176.8 ₹ 11,768.00

Filling the gap in between aluminium frame and adjacent RCC/Brickwork/

Stone Work by providing weather silicon sealant over backer rod of approved

quality as per architectural drawings

and direction of Engineer-in-charge

21.8.1 Upto 5mm depth and 5mm width metre 10.43 96.75 1009.00

22.0 WATER PROOFING

Providing and laying water proofing treatment to vertical and

65 22.3 horizontal surfaces of depressed portions of W.C., kitchen and the like

consisting of :

Digitally signed by PRIYA

ITEM DSR DSR NDSR NDSR

S. NO DESCRIPTION OF ITEMS UNIT QTY

CODE-DSR RATE AMOUNT RATE AMOUNT

(i) Ist course of applying cement slurry @ 4.4 Kg/sqm mixed with water

proofing compound conforming to IS 2645 in recommended proportions

including rounding off junction of vertical and horizontal surface.

(ii) IInd course of 20mm cement plaster 1:3 (1 cement : 3 coarse sand)

mixed with water proofing compound in recommended proportion

including rounding off junction of vertical and horizontal surface. (iii)

IIIrd course of applying blown or residual bitumen applied hot at 1.7

Kg. per sqm of area. (iv) IVth course of 400 micron thick PVC sheet.

(Overlaps at joints of PVC sheet should be 100 mm wide and

pasted to each other with bitumen @ 1.7 Kg/sqm.)

Supplying and Stacking Filling sunken floor with over burnt jhama brick

66 16.3.4 aggregate 120mm to 40mm including compacting of materials complete as Cum 5.00 798.10 3990.50

specified and directed for all levels.

Providing & laying integral cement based water proofing treatment

including preparation of surface as required for treatment of roofs,

balconies, terraces etc consisting of following operations: a)

Applying a slurry coat of neat cement using 2.75kg/sqm of cement

admixed with water proofing compound confirming to IS. 2645 and approved

by Engineer-in-charge over the RCC slab including adjoining walls

upto 300mm height including cleaning the surface before treatment. b)

Laying brick bats with mortar using broken bricks/brick bats 25mm to

115mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse

sand ) admixed with water proofing compound confirming to IS :

2645 and approved by Engineer-in- charge over 20 mm thick layer of

cement of 1:5 ( 1 cement : 5 coarse sand ) admixed with water proofing

compound confirming to IS : 2645 and approved by Engineer-in-charge

to required slope and treating similarly the

Digitally signed by PRIYA

ITEM DSR DSR NDSR NDSR

S. NO DESCRIPTION OF ITEMS UNIT QTY

CODE-DSR RATE AMOUNT RATE AMOUNT

adjoining walls upto 300mm height including rounding of junctions of walls

and slabs. c) After two days of proper curing applying a second coat of

cement slurry using 2.75kg/sqm of cement admixed with water proofing

compound confirming to IS : 2645 and approved by Engineer-in-

charge. d) Finishing the surface with 20 mm thick jointless cement

mortar 1:4 (1 cement : 4 coarse sand ) admixed with water proofing

compound confirming to IS : 2645 and approved by Engineer-in-charge

including laying glass fibre cloth of approved quality in top layer and

finally finishing the surface with trowel with neat cement slurry and

making pattern of 300x300 mm square 3mm deep. e) The whole terrace so

finished shall be flooded with water for a minimum period of two weeks

for curing and for final test. All above operations to be done in order

and as directed and specified by the Engineer-in-charge:

With average thickness of 120mm and minimum thickness at khurra

Digitally signed by PRIYA

ITEM DSR DSR NDSR NDSR

S. NO DESCRIPTION OF ITEMS UNIT QTY

CODE-DSR RATE AMOUNT RATE AMOUNT

Providing and applying integral crystalline slurry of hydrophilic in

nature for waterproofing treatment to the RCC structures like

retaining walls of the basement, water tanks, roof slabs, podiums,

reservior, sewage & water treatment plant, tunnels / subway and bridge

deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral

crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts

integral crystalline slurry : 1 part water) for horizontal surfaces and

applying the same from negative (internal) side with the help of

synthetic fiber brush. The material shall meet the requirements as

specified in ACI-212-3R-2010 i.e by reducing permeability of concrete

by more than 90% compared with control concrete as per DIN 1048 and

resistant to 16 bar hydrostatic pressure on negative side. The crystalline

slurry shall be capable of self- healing of cracks up to a width of 0.50mm.

The work shall be carried out all complete as per specification and the

direction of the engineerin- charge. The product performance shall carry

guarantee for 10 years against any leakage.

22.23.1 For vertical surface two coats @0.70 kg per sqm Sqm 10.00 472.90 4729.00

22.23.2 For horizontal surface one coat @1.10 kg per sqm. Sqm 10.00 362.80 3628.00

AMOUNT 12266198.98

Plumbing work & water supply

Providing and fixing white vitreous china pedestal type water closet (European type

W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern,

including flush pipe, with manually controlled device (handle lever),

conforming to IS : 7231, with all fittings and fixtures complete, including

cutting and making good the walls and

floors wherever required :

17.2.1 W.C. pan with ISI marked white solid plastic seat and lid Each 6 6515.55 39093.30

Digitally signed by PRIYA

ITEM DSR DSR NDSR NDSR

S. NO DESCRIPTION OF ITEMS UNIT QTY

CODE-DSR RATE AMOUNT RATE AMOUNT

roviding and fixing white vitreous china flat back or wall corner type lipped front

urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with

70 17.4 automatic flushing cistern with standard flush pipe and C.P. brass spreaders with

brass unions and G.I clamps complete, including painting of fittings and brackets,

cutting and making good the walls and floors wherever required :

17.4.2 Range of two urinal basins with 5 litre white P.V.C. automatic flushing cistern Each 3 9612.4 28837.20

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar

71 17.7 taps, 32 mm C.P. brass waste of standard pattern, including painting of

fittings and brackets, cutting and making good the walls wherever require:

White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass

Providing and fixing white vitreous china pedestal for wash basin completely

recessed at the back for the reception of pipes and fittings.

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality &

make and as per the direction of Engineer-in-charge.

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make

as approved by Engineer in charge.

a 15 mm nominal dia Each 4.00 6940.75 27763.00

Providing and fixing P.V.C. Waste pipe for sink or wash basin including

P.V.C. waste fittings complete.

17.28.1 Semi rigid pipe

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved

17.31 quality) complete with 6 mm thick hard board ground fixed to wooden cleats with Each 6.00 1607.95 9647.70

C.P. brass screws and washers complete.

76 DSR-17.34 Providing and fixing toilet paper holder :

Providing and fixing C.P. brass bib cock of approved quality conforming to

18.49.1 15 mm nominal bore Each 6.00 506.80 3040.80

Providing and fixing C.P. brass long body bib cock of approved quality conforming

to IS standards and weighing not less than 690 gms.

18.50.1 15 mm nominal bore Each 6.00 820.70 4924.20

Providing and fixing C.P. brass angle valve for basin mixer and

geyser points of approved quality conforming to IS:8931

Digitally signed by PRIYA

ITEM DSR DSR NDSR NDSR

S. NO DESCRIPTION OF ITEMS UNIT QTY

CODE-DSR RATE AMOUNT RATE AMOUNT

18.53.1 15 mm nominal bore Each 6.00 574.30 3445.80

80 18.22 Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved

81 DSR-18.53A make and quality as per direction of Engineer-in- Each 6 74.8 448.80

Providing and placing on terrace (at all floor levels) polyethylene water storage tank,

IS : 12701 marked, with cover and suitable locking arrangement and making

necessary holes for inlet, outlet and overflow pipes but without fittings and the base

support for tank.

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15

cm diameter and weighing not less than 440 grams.

Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm

18.21.2.1 15 mm nominal bore Each 10 97.75 977.50

Providing and fixing health faucet with 8 mm dia and 1.2 m long flexible tube

and wall hook including all fittings

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes

86 12.41 conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS :

5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories

for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A,

including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for

thermal expansion.

12.42.1 Coupler

Water Supply (Internal & External)

Digitally signed by PRIYA

ITEM DSR DSR NDSR NDSR

S. NO DESCRIPTION OF ITEMS UNIT QTY

CODE-DSR RATE AMOUNT RATE AMOUNT

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply, including all CPVC plain & brass threaded

fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of

pipes & fittings with one step CPVC solvent cement and the cost of cutting chases

88 18.8 and making good the same including testing of joints complete as per direction of

Engineer in Charge. Concealed work, including cutting chases and making good the

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c

cutting and making good the walls etc.

Internal work - Exposed on Wall For Roof

18.10.3 25 mm dia nominal bore Metre 10 551.7 5517.00

18.10.4 32 mm dia nominal bore Metre 20.00 667.00 13340.00

18.10.5 40 mm dia nominal bore Metre 30 811.9 24357.00

18.10.6 50 mm dia nominal bore Metre 20.00 1048.35 20967.00

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having

thermal stability for hot & cold water supply including all CPVC plain & brass

90 DSR - 18.9 threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent

cement, trenching, refilling & testing of joints complete as per direction of

Engineer in Charge. EXTERNAL WORKS

18.9.4 32 mm nominal outer dia Pipes Metre 15.00 438.60 6579.00

18.9.5 40 mm nominal outer dia Pipes Metre 10 563.05 5630.50

18.9.6 50 mm nominal outer dia Pipes Metre 10.00 794.25 7942.50

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and

18.12.3 25 mm dia nominal bore Metre 10 467.75 4677.50

18.12.5 40 mm dia nominal bore Metre 12.00 617.05 7404.60

18.12.6 50 mm dia nominal bore Metre 10 762.15 7621.50

Digitally signed by PRIYA

ITEM DSR DSR NDSR NDSR

S. NO DESCRIPTION OF ITEMS UNIT QTY

CODE-DSR RATE AMOUNT RATE AMOUNT

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement

mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100

x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1

cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c

necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded

stone aggregate 40 mm nominal size ) and inside plastering with cement mortar

1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat

cement complete as per standard design :

With common burnt clay F.P.S.(non modular) bricks of class

designation 7.5

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement

mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with

C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep (

inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4

93 DSR-18.33 graded stone aggregate 20mm nominal size ) , i/c necessary excavation,

foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate

40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement :

3 coarse sand) 12 mm thick, finished with a floating coat of neat cement

complete as per standard design :

With common burnt clay F.P.S.(non modular) bricks of

class designation 7.5

Constructing masonry Chamber 90x90x100 cm inside, in brick work in cement mortar

1:4 (1 cement : 4 coarse sand) for sluice valve, with

C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep

(inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4

94 DSR-18.34 graded stone aggregate 20 mm nominal size ), i/c necessary excavation,

foundation concrete 1:5:10 (1 cement

: 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside

plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick,

finished with a floating coat of neat cement complete as per standard design :

18.34.1 With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 Each 1 18896.7 18896.70

Painting G.I. pipes and fittings with synthetic enamel white paint with two

coats over a ready mixed priming coat, both of approved quality for new work :

18.38.3 25 mm dia nominal bore Metre 15 30.25 453.75

18.38.4 32 mm dia nominal bore Metre 10.00 36.35 363.50

Digitally signed by PRIYA

ITEM DSR DSR NDSR NDSR

S. NO DESCRIPTION OF ITEMS UNIT QTY

CODE-DSR RATE AMOUNT RATE AMOUNT

18.38.5 40 mm dia nominal bore Metre 5 42.65 213.25

18.38.6 50 mm dia nominal bore Metre 5.00 51.00 255.00

Painting G.I. pipes and fittings with two coats of anti-orrosive

bitumastic paint of approved quality :

18.40.3 25 mm dia nominal bore Metre 15 18.35 275.25

18.40.5 40 mm dia nominal bore Metre 10.00 25.25 252.50

18.40.6 50 mm dia nominal bore Metre 10 30.5 305.00

Providing and filling sand of grading zone V or coarser grade,

allround the G.I. pipes in external work :

18.41.3 25 mm dia nominal bore Metre 15 160.7 2410.50

18.41.5 40 mm dia nominal bore Metre 10.00 167.00 1670.00

18.41.6 50 mm dia nominal bore Metre 10 173.25 1732.50

Providing and fixing G.I. Union in G.I. pipe including cutting and threading

98 18.47 the pipe and making long screws etc. complete (New

18.47.2 20 mm dia nominal bore Each 15 857.85 12867.75

18.47.3 25 mm dia nominal bore Each 10.00 950.35 9503.50

18.47.4 32 mm dia nominal bore Each 10 1000.15 10001.50

18.47.5 40 mm dia nominal bore Each 5.00 1142.40 5712.00

18.47.6 50 mm dia nominal bore Each 5 1520.8 7604.00

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe

etc. and repairing the hole after insertion of drain pipe etc. with cement

99 DSR-18.77 concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm Each 10.00 452.00 4520.00

nominal size), including finishing complete

so as to make it leak proof.

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of

100 19.1 cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of

joints etc. complete :

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded

101 19.2 stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as

per standard design :

Digitally signed by PRIYA

ITEM DSR DSR NDSR NDSR

S. NO DESCRIPTION OF ITEMS UNIT QTY

CODE-DSR RATE AMOUNT RATE AMOUNT

Providing and fixing square-mouth S.W. gully trap class SP-1 complete withC.I.

grating brick masonry chamber with water tight C.I. cover with frame of300 x300 mm

size (inside) the weight of cover to be not less than 4.50 kg and fame to be not less

than 2.70 kg as per standard design

19.4.1 100x100 mm size P type

19.4.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 each 2 2707.65 5415.30

Electrical work & Fire Fighting work

SUB HEAD-I: WIRING & SUBMAIN

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5

sq.mm FRLS PVC insulated copper conductor single core cable in surface /

recessed medium class PVC conduit, with modular switch, modular plate,

suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated

copper conductor single

core cable etc as required.

Wiring for group controlled (looped) light point/fan point/exhaust fan

point/ call bell point (without independent switch etc.) with 1.5 sq. mm

104 1.55 FRLS PVC insulated copper conductor single core cable in surface/

recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC

insulated copper conductor single core cable etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover

in front on surface or in recess, including providing and fixing 3 pin 5/6

105 1.31 amps modular socket outlet and 5/6 amps modular switch, Each 71.00 507.19 36010.78

connection etc. as required. (For light plugs to be used in non residential

Supplying and fixing suitable size GI box with modular plate and cover

in front on surface or in recess, including providing and fixing 6 pin 5/6 &

15/16 amps modular socket outlet and 15/16 amps modular switch,

connection etc. as required.

Digitally signed by PRIYA

ITEM DSR DSR NDSR NDSR

S. NO DESCRIPTION OF ITEMS UNIT QTY

CODE-DSR RATE AMOUNT RATE AMOUNT

Supplying & fixing suitable size GI box wih modular plate and cover in front

on surface or in recess including providing and fixing 25 A modular

socket outlet and 25 A modular SP MCB, "C" curve including

connections, painting etc. as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following

108 1.1 sizes of FRLS PVC insulated copper conductor, single core cable in surface/

recessed medium class PVC conduit as required.

1.14.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire Metre 210 355.1422 74579.862

1.14.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire Metre 50 466.7887 23339.435

1.14.9 4 X 6 sq. mm + 2 X 6 sq. mm earth wire Metre 50.00 801.73 40086.41

40192 4 X 10 sq. mm + 2 X 6 sq. mm earth wire Metre 50 1068.6165 53430.825

Supplying and fixing following modular switch/ socket on the existing

109 1.24 modular plate & switch box including connections but excluding

modular plate etc. as required.

1.24.7 TV antenna socket outlet Each 4 157.3684 629.4736

Supplying and fixing following size/ modules, GI box alongwith modular

110 1.27 base & cover plate for modular switches in recess etc. as

Supplying and fixing following Modular base & cover plate on

existing modular metal boxes etc. as required.

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper

conductor PE insulated, shielded with fine tinned copper braid and

protected with PVC sheath in the existing surface/ recessed steel/

PVC conduit as required.

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated

113 1.18 annealed copper conductor, unarmored telephone cable in the existing

surface/ recessed steel/ PVC conduit as required.

Digitally signed by PRIYA

ITEM DSR DSR NDSR NDSR

S. NO DESCRIPTION OF ITEMS UNIT QTY

CODE-DSR RATE AMOUNT RATE AMOUNT

Supplying and drawing PVC insulated, PVC sheathed multicore armored

114 taped telephone cables of 0.05 mm dia size in existing conduit pipe, of

the following sizes.

Supplying and fixing of telephone distribution board (tag block) in hinged

115 type MS box duly powder coated complete with bakelite sheet with terminal

nation of incoming and outgoing telephone wire etc. complete as required.

Supplying and fixing following modular switch/ socket on the existing

116 1.24 modular plate & switch box including connections but excluding

modular plate etc. as required.

1.24.6 Telephone socket with shtter outlet Each 6.00 157.37 944.21

Supplying and fixing of following sizes of medium class PVC conduit along

with accessories in surface/recess including cutting the wall and making

good the same in case of recessed

conduit as required.

Supplying and fixing modular blanking plate on the existing modular plate &

switch box excluding modular plate as required.

SUB HEAD -II: DISTRIBUTION BOARD

Supplying and fixing following way, horizontal type three pole and neutral,

sheet steel, MCB distribution board, 415 V, on surface/ recess, complete

119 2.4 with tinned copper bus bar, neutral bus bar, earth bar, din bar,

interconnections, powder painted including earthing etc. as required. (But

without MCB/RCCB/ Isolator)

Digitally signed by PRIYA

ITEM DSR DSR NDSR NDSR

S. NO DESCRIPTION OF ITEMS UNIT QTY

CODE-DSR RATE AMOUNT RATE AMOUNT

Supplying and fixing following way, single pole and neutral,

sheet steel, MCB distribution board, 240 V, on surface/ recess,

120 2.30 complete with tinned copper bus bar, neutral bus bar, earth bar, din bar,

interconnections, powder painted including earthing etc. as required.

(But without MCB/RCCB/Isolator)

2.3.1 6 way , Double door Each 1.00 2345.64 2345.64

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C"

curve, miniature circuit breaker suitable for inductive load of

following poles in the existing MCB DB complete with connections, testing

and commissioning etc. as required.

2.10.5 Triple Pole & neutral Each 2 1305.7324 2611.4648

Supplying and fixing single pole blanking plate in the existing MCB DB

complete etc. as required.

Supplying and fixing following rating, four pole, 415 volts, MCB in the

NS existing MCB DB complete with connections, testing and

commissioning etc. as required.

Supplying and fixing following rating, double pole, (single phase and

neutral), 240 volts, residual current circuit breaker (RCCB), having a

sensitivity current upto 300 milliamperes in the existing MCB DB

complete with connections, testing and commissioning etc. as required.

Digitally signed by PRIYA

ITEM DSR DSR NDSR NDSR

S. NO DESCRIPTION OF ITEMS UNIT QTY

CODE-DSR RATE AMOUNT RATE AMOUNT

Supplying and fixing of following ways surface/ recess mounting,vertical

type, 415 volts, TPN MCB distribution board of sheet steel,dust protected,

duly powder painted, inclusive of 200 amps tinned copper bus bar, common

neutral link, earth bar, din bar for mounting MCB's (but without MCB's and

incomer ) as required. (Note : Vertical type MCB TPDB is normally used

where 3 phase outlets are required.)

Supplying and fixing TP sheet steel enclosure on surface/ recess along with

127 2.17 16/25/32amps 415 volts "C" curve TP MCB complete with connections, Each 1 1692.7736 1692.7736

testing and commissioning etc. as required.

Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet,

with 2 pole and earth, metal enclosed plug top alongwith 20 amps "C" curve,

128 2.18 SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal Each 1 1723.6093 1723.61

cover for the socket out let and complete with connections, testing and

commissioning etc. as required.

Supplying and fixing 20 amps, 415 volts, TPN industrial type, socket outlet,

with 4 pole and earth, metal enclosed plug top alongwith 20 amps "C" curve,

129 2.19 TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal Each 1 2753.947 2753.947

cover for the socket out let and complete with connections, testing and

commissioning etc. as required.

Sub-Head - III: LIGHTING FIXTURES

Supplying and fixing Surface mounted of 36 W 2x2ft LED LIGHT complete

with electronic driver & LED directly on ceiling including connection with

1.5 sq.mm FR PVC insulated copper conductor cable and earthing the

body etc. as required.

Supplying and fixing Surface mounted 20 watt LED Tube light complete with

electronic driver & LED directly on ceiling/wall including connection with

1.5 sq.mm FR PVC insulated copper conductor cable and earthing the

body etc. as required.

Digitally signed by PRIYA

ITEM DSR DSR NDSR NDSR

S. NO DESCRIPTION OF ITEMS UNIT QTY

CODE-DSR RATE AMOUNT RATE AMOUNT

Supplying and fixing Surface mounted 12 watt LED downlighter complete

with integrated driver & LED directly on ceiling including connection with

1.5 sq.mm FR PVC insulated copper conductor cable and earthing the

body etc. as required.

Supplying and fixing Surface mounted 10 watt LED mirror light complete

with electronic driver & LED directly on ceiling/wall including connection

with 1.5 sq.mm FR PVC insulated copper conductor cable and earthing

the body etc. as required.

Supplying and fixing Surface mounted 10 watt LED type Bulk-head fitting

comprising of pressure die cast housing with acrylic diffuser (IP65) and

134 NS-10 complete with electronic driver etc directly on wall/ceiling including Each 8 1507.63 12061.016

connection with 1.5 sq.mm FR PVC insulated copper conductor cable and

earthing the body etc.

Supply and installation of ceiling fan of 1200mm sweep including

wiring the down rods of standard length (up to 30cm) with 1.5sq

mm FR PVC insulated copper

Supply and installation of 200 mm, 230V A.C exhaust fan in the

136 NS-12 existing opening including making good the damage connection testing Each 5 2809.67 14048.3425

commissioning etc as required

Supplying and fixing two module stepped type electronic fan

137 1.3 regulator on the existing modular plate switch box including connections but Each 18.00 392.36 7062.44

excluding modular plate etc. as required.

SUB HEAD-IV - MV PANELS

Digitally signed by PRIYA

ITEM DSR DSR NDSR NDSR

S. NO DESCRIPTION OF ITEMS UNIT QTY

CODE-DSR RATE AMOUNT RATE AMOUNT

Design, Fabrication, Supply, Erection,Testing and commisioning of

Powder coated SDB LT Panel fabricated out of 2mm CRCA sheet steel

in cubical, compartmentallised, free standing floor /wall mounted, dust and

vermin proof, with reinforcement of suitable size angle iron, channel, T -

iron or flats as required. Cable gland plates shall be provided on top as

well as bottom of the panels. Panels shall be treated with all anti-corrosive

process before painting as per specification. Panels shall be suitable for

415V, 3-Phase, Four wire, 50 Hz supply complete with earth bus and lifting

hooks as required in case of large panels.Approval shall be taken for each

panel before fabrication. (All hardwares like nuts and bolts used

shall be Galvanized and Zinc passivated)As per Specification.

1 No.63 amps TPN MCCB(25 KA) with thermal Magnetic release

(PRMB-3) with Class-C transient voltage surge suppression device

suitable for 3 phases as per specifications.

B METERING & INDICATION

i) 1 set of R,Y,B phase indicating lamps

ii) 1 Set of Breaker ON-OFF-TRIP,indication Lamps

1 Nos. Load Analyser cum digital Multifunction Meter with 3 nos.

60/5A, CL-1 CTs, as required.

1 Set of 100A TPN Aluminium Bus Bar with colour coded PVC

i) 2 NOS 63 FP MCB

ii) 3 NOS 40 FP MCB

iii) 2 NOS 40DP MCB

SDB - 1 (Ground Floor) as described above SET 1.00 246702.60 246702.6

Digitally signed by PRIYA

ITEM DSR DSR NDSR NDSR

S. NO DESCRIPTION OF ITEMS UNIT QTY

CODE-DSR RATE AMOUNT RATE AMOUNT

Supply,Installation,Testing and Commissioning of Three Phase Dual Source

139 NS-14 Energy Smart Meter (40-125A,CT operated) along with CTs Enclosure etc Each 1.00 34264.25 34264.25

complete as required.

Supply, following sizes of PVC sheathed XLPE insulated Aluminium

conductor multicore armoured cable of 1.1 KV grade.

NS-16 4C- 25 sq mm Aluminium RM 40 1350.34 54013.61547

NS-17 4C- 16 sq mm Aluminium RM 10 509.85 5098.5204

NS-18 4C- 10 sq mm Aluminium RM 50.00 426.25 21312.3635

Supplying and making end termination with brass compression gland

and aluminium lugs for following size of PVC insulated and PVC

sheathed / XLPE aluminium conductor cable of 1.1 KV grade as

4C- 25 sq mm Aluminium SET 2 334.9395 669.88

4C- 16 sq mm Aluminium SET 2 328.5597 657.12

4C- 10 sq mm Aluminium SET 4.00 286.03 1144.11

Laying of one number PVC insulated and PVC sheathed / XLPE power

cable of 1.1 KV grade of following size direct in ground including

excavation, sand cushioning, protective covering and refilling the trench

etc as required.

7.1.4 Above 185 sqmm and Upto 400sq. mm RM 80 504.0042 40320.34

Perforated trays

Supplying and installing following size of perforated painted with

powder coating M.S. cable trays with perforation not more than 17.5%,

143 4.1 in convenient sections, joined with connectors, suspended from the

ceiling with M.S. suspenders including bolts & nuts,

painting suspenders etc as required.

4.1.4 300 mm width X 50 mm depth X 1.6 mm thickness Mtr 30 826.1841 24785.523

Digitally signed by PRIYA

ITEM DSR DSR NDSR NDSR

S. NO DESCRIPTION OF ITEMS UNIT QTY

CODE-DSR RATE AMOUNT RATE AMOUNT

4.1.2 150 mm width X 50 mm depth X 1.6 mm thickness Mtr 10 642.2332 6422.332

SUBHEAD V:EARTHING SYSTEM & LIGHTNING PROTECTION

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick

including accessories, and providing masonry enclosure with cover plate

having locking arrangement and watering pipe of 2.7 meterlong etc. with

charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from

145 5.11 earth electrode including connection with G.I. nut, bolt, spring, washer RM 30 750.6898 22520.69

excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recessfor

connections etc. as required

Providing and fixing 6 SWG dia G.I. wire on surface or in recess

147 5.18 for loop earthing along with existing surface/ recessed conduit/ RM 120.00 44.66 5359.03

submain wiring/ cable as required.

Providing and fixing of lightning conductor finial, made of 25 mm dia 300

148 6.2 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick Each 6.00 550.79 3304.74

G.I. base plate including holes etc. complete as required.

Fixing of lightning conductor finial (single prong) with base plate including

holes etc. complete as required.

Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial

150 6.4 or any other metallic object) by riveting / nut bolting/sweating and soldering Each 20.00 120.15 2403.06

etc as required

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of

wall for lightning conductor complete as required. (For horizontal run)

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of

wall for lightning conductor complete as required. (For vertical run)

Digitally signed by PRIYA

ITEM DSR DSR NDSR NDSR

S. NO DESCRIPTION OF ITEMS UNIT QTY

CODE-DSR RATE AMOUNT RATE AMOUNT

Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125

153 6.12 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. Each 6.00 128.66 771.96

complete as required

SUB HEAD-VI : ALARM SYSTEM (CONVENTIONAL)

Supplying, installation, testing & commissioning sector panel

suitable for following zones, complete with visual indications for short

154 17.1.9 circuit fault, open circuit fault, fire condition and all other standard

facilities as per IS:2189 with mimic diagram for all area/zone

covered, complete with all connections, interconnections as required.

Supplying, installation, testing & commissioning of manual call boxes

155 17.1.3 of MS construction in surface/recess with stainless steel chain & hammer Nos 4.00 504.00 2016.02

assembly complete with glass and push button etc. as required.

Supplying, installation, testing & commissioning fire alarm sounder with

facility to make announcement, mounted in M.S. box (16 SWG) with hinged

cover plate & suitable for operation with amplifier i/c line matching

transformer etc. complete as required.

Supplying and drawing following sizes of FR PVC insulated copper

157 1.17 conductor, single core cable in the existing surface/ recessed PVC conduit as

Supplying and fixing of following sizes of medium class PVC conduit along

158 1.21 with accessories in surface/recess including cutting the wall and making

good the same in case of recessed conduit as required.

SUB HEAD-VII : FIRE FIGHTING

Digitally signed by PRIYA

ITEM DSR DSR NDSR NDSR

S. NO DESCRIPTION OF ITEMS UNIT QTY

CODE-DSR RATE AMOUNT RATE AMOUNT

Providing and fixing carbon-di-oxide type fire extinguishers

consisting of welded M.S. cylindrical body, internal discharge tube,

159 NS 19 discharge nozzle, suspension bracket, conforming to IS 2878,

finished externally with red enamel paint and fixed to wall with

brackets complete with internal charges.

Providing & Fixing of stored pressure Fire Extinguisher ABC

powder type (Mono Ammonium Phosphate Powder) Magnetic

Pressure Gauge having the facility to check at site, Discharge Time less

than 9 Secs, Controllable discharge mechanism, Range minimum 4

Meters, applicable on Class A,B,C and electrically started Fire, A

160 NS 20 Rating- 21A, B Rating 55B as per BS EN-3 BIS 15683 marked, Can

Construction : Deep drawn & CO2 Mig welded, Valve Construction :

Forging & Machining, Internal Coating of Can : Epoxy Powder

coating, External Coating ofCan : Epoxy Polyster Powder coating,

Sheet metal thickness : 1.60MM, Helium

LeakDetection Tested, Warranty.

Capacity 6 Kg. Nos. 4 4934.05 19736.208

Digitally signed by PRIYA

ITEM DSR DSR NDSR NDSR

S. NO DESCRIPTION OF ITEMS UNIT QTY

CODE-DSR RATE AMOUNT RATE AMOUNT

Table Size 2400 mm (w) x 600 mm (D) X 740 mm. .TABLE TOP :- The Table Top is made of

25mm thick prelam particle board confirming to IS 12823 Interior Grade. The exposed edges of

the table top are sealed with 2mm PVC edge banding. The height of the table top from the

ground should be 740mm.Legs:- The legs are 50 x 50mm thick Square pipe made of 1.6mm

thick CRCA pipe duly powder coated. The powder coating thickness considered is 50 to 60

microns DFT. Tie Member :- The tie member should be 80 x 40mm pipe structure made of

1.6mm thick CRCA duly powder coated. The powder coating thickness considered is 50 to 60

microns DFT. Structure to fully welded with all arc welding from inside eliminating manual

161 NS 21 finishing. None of the welding joints should be visible from outside.LEG SHOE/LEVELLERS :- Nos. 4.00 33202.06 132808.233

The leg shoe is made up of 100% recyclable nylon 6. The shoe helps in mounting of levelers on

the legs by eliminating any welding process. The levelers are made of Nylon 6 with M8 bolts

insert moulded to take care of any floor undulation.BEAM :- The beam is 1.2mm thick CRCA

bent in the form of C channels with 3mm thick CRCA brackets. The bottom cover is made of 0.7

mm thick GI sheet. All welding is from inside eliminating manual finishing. The beam acts as a

main spine, stiffeners and also cable carrying raceway thus eliminating use of extra material.

The size of the beam is 100mm height and depth of 445mm for sharing. In case of non sharing

the size is 100mm height and 190mm depth.

Providing and Placing Table for study.The Table Top shall be made out of 25 mm thick Pre

laminated particle board of approved shade, design and colour. The Gable end shall be made

162 NS 22 out of 18 mm thick Pre laminated particle board of approved shade, design and colour. The Nos. 1.00 14469.11 14469.10749

modesty panel of the table shall be 600mm height made of 18mm thick Pre laminated particle

board.. Size: 750(w) x 900(D) x 750(Ht)mm.

Placing Visitor Chair ergonomically designed for user comfort & shall have aesthetically

appealing design. The seat shall be made of 12mm thick hot pressed plywood upholstered with

high resilience polyurethane foam having density 48kg/m³ with fabric tapestry of 300 GSM

163 NS 23 and the back shall be made of polypropylene. The arm shall be provided MS chrome plated Nos. 20 7702.60 154052.068

having Dia. 25.4mm with PU on top for comfort. The frame structure shall be four legged

support type made up of chrome plate round pipe of Dia 20 mm with 1.5mm thick. There shall

be PPCP shoe provided at the base to avoid scratches on the floor. ..

Digitally signed by PRIYA

ITEM DSR DSR NDSR NDSR

S. NO DESCRIPTION OF ITEMS UNIT QTY

CODE-DSR RATE AMOUNT RATE AMOUNT

Providing & Placing Single Sided Book Rack of overall size 925(w) x 300(d) x 2100(ht)mm The

Rack shall have five fixed shelf with 1 bottom shelf makes six storage levels. Racks. All metal

part (shelves, back support etc) shall be made of CRCA 0.8mm thickness high yield strength

CRCA sheet of grade ‘D’ confirming to IS: 513. Side panels Shall be made of 25mm thick pre

laminated particle board with decorative laminate on both sides, edges duly sealed with PVC

164 NS 24 edge banding tape. The skirting and top panel shall be made of metal/Pre-laminated board.

Stackbility shall have add -on units width wise to form a bank of racks having common side

panel . Label holder on each main unit to insert labels for identification. Finish shall be Epoxy

polyester powder coated to the thickness of 40-50 microns after 7 tank pre-treatment process

flow for metal parts.

Supplying and placing ergonomically designed, comfortable & aesthetically appealing

Medium back chair. The seat shall be made of 12mm thick hot pressed commercial plywood

upholstered with high resilience moulded polyurethane foam having density 48kg/m³ with

foam net tapestry. The seat shall be upholstered with fabric tapestry 0.8mm thick and 300 GSM

and the back shall be made of polypropylene net cover upholstered with breathable mesh

165 NS 25 tapestry. The backrest shall be made with contoured lumbar support and maintain the natural Nos. 1.00 18800.11 18800.10869

curvature of the spine. The chair shall be supplied with black integral polypropylene arm. The

chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and

tilt tension adjustment. The Pedestal should have five legged injection moulded black nylon

having pitch circle dia. 650 mm fitted with 5 nos. twin wheel castors which shall be made of

injection moulded in 30% glass filled nylon.

AMOUNT 367597.84

Digitally signed by PRIYA