SPECIAL REPAIR TO BLDG NO T-49 AND T-55 AT 217 TRANSIT CAMP AT MANALI UNDER AGE (I) RnD MANALI

Amount

Dismantling plain or corrugated steel sheeting, any guage, thickness, including nainital or similar pattern roof coverings, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

S&F mild steel in joist channel, angle, or tee sections, hollow or round steel tubes, fixed independently, without connecting plates, etc. (cut to ordinary lenghts i.e. within 20mm of the length indicated), Fe 410-W (Gde-250) quality-A complete all as specified and directed.

S&F mild steel windows chajja/wind ties for roof covering including screwing bolts, etc complete all as specified and directed.

S&F pre-painted galvalume sheet zinc coating GI based corrugated steel 0.50mm thick of approved colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and directed.

M&L for preparation of new steel surfaces of any description over 10cm in width or girth not otherwise described and applying 2 coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Dismantling of wall/ceiling boards (fibre, pulp, insulation, etc) or insulation boards/slabs/blankets, any thickness including cover fillets, complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for 75mm thick PCC type D-2 (1:4:8) using 40mm graded stone aggregate as in subbase of floor complete all as specified and directed.

Demolition of cement conc. as in floors etc. and paving not exceeding 15 cm thickness below or above ground level (un-reinforced) all as directed.

M&L for machine cut kota stone flooring 20-25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and incl 20mm thick screed bed or bedding layer of cement mortar 1:6 complete all as specified and directed.

M&L for 50mm thick PCC 1:3:6 type C2 using 40mm graded stone aggregate as in plinth protection even and smooth without using extra cement all as specified and directed.

M&L for 12mm thick pre laminated particle board interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws frame work as in wall panelling complete all as specified and directed.

M&L for 12mm thick pre laminated particle board interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws frame work as in ceiling complete all as specified and directed.

M&L plain fillets, square, rectangular or triangular in section, clean sawn, secured with nails or brads of size exc 3 sqm and not exc 6 sqm of second class softwood complete all as specified and directed.

M&L for second class softwood timber framed and fixed, clean sawn in scantling, all as specified and directed.

S&F 4.00 mm thick sheet glass ordinary quality and glazing with oil putty in square n.exc 0.5 sqm in each pane complete all as specified and directed.

Demolition of brick work or stone/boulder masonary, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc. but excluding ashlar facings, dressed stonework and precast articles, complete all as specified and directed.

M&L for pre-cast cement concrete block 1:3:6 type C-1 (using 20mm graded aggregate) masonary with solid blocks, exc. 10cm in width and setting in cement mortar 1:6 complete all as specified and directed.

M&L for rendering 15mm thick on brickwork or concrete surfaces or surface other than fair faces or brickwork in CM (1:4) finished even & fair (without using extra cement) complete all as specified and directed.

M&L for preparation of new plastered surface of wall and applying two coats of cement base paint, white or tinted complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) exc. 1.5 Sqm and not exc 4 Sqm each all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) not exc. 1.5 Sqm all as specified and directed.

Supply and fix steel windows with side hung shutters including projecting type hinges with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded all as specified and directed.

S&F pressed steel door frames with one or more rebates including necessary fixing lugs hinges lock strike plate etc complete size of frame 125x60 mm all as specified and directed.

S&F flush shutters, 30 mm thick solid core construction, with block board core and plywood face panels, commercial type, on both sides as per SSR part-I all as specified and directed.

S&F mild steel butt hinges, medium weight cold rolled 100mm size all as specified and directed.

S&F extruded aluminium alloy handles, fabricated type, 150mm size all as specified and directed.

S&F aluminium anodised, barrel tower bolts of extruded section and fixed length of bolt 150mm long all as specified and directed.

S&F of mild steel sliding door, bolts, plate type, stove enamelled black with bright bolt not less than 12mm bore, length of bolt 250mm all as specified and directed

M&L for preparing new wooden surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of primer complete all as specified and directed.

S&F mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars barred iron doors, ladders framed balusters walk ways railings framework of water tanks

M&L for galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised wire staples all as specified and directed.

S&F for 25mm dia stainless steel curtain rod fixed with MS hooks incl side brackeets (both side) complete all as specified, approved and directed.

BLANK

Supplying and fixing steel windows 1.25 mm thick Box type (primer coated) ERW hollow 'P' section of size 60 mm × 25 mm single rebated comprises of glazed shutter EWR sec 50 mm x 20 mm and 1 mm thick and two openable leaf conisting two Nos sash bar of 'T' section 20 mm x 3 mm complete welded to frame with one vertical mullion of EWR bolt 'T' section of size 60 mm x 25 mm and 1.25 mm thick including cuttings holes and making good dismantled portion for each window including following fittings welded to failed shutter:- (a) Holdfasts 150 mm long 12mm x 3 mm made to shape- 4 Nos per window (b) Handle of Z sec 20 mm x 25 mm, 100 mm long - 1 No per leaf. (c) MS tower bolt 150 mm long - 2 Nos per leaf. (d) 'Z' sec 20 mm x 25 mm, 100 long stopper-01 No per leaf, (e) Cleat 55mm long of hollow square 15 mm x 20 mm x 63 mm welded to hinges - 1 No per leaf | (1) MS pintal hinges of size 75 mm x 12 mm - 2 Nos per leaf. (g) fabriction and fixing arrangement complete. Note:- Grill / guard bars, glass pane shall be measured and Paid for seperately

Supplying and fixing steel windows 1.25 mm thick Box type (primer coated) ERW hollow 'P' section of size 60 mm × 25 mm single rebated comprises of gauged shutters without sash bars EWR sec 50 mm x 20 mm and 1 mm thick and two openable leaf conisting two Nos sash bar of 'T' section 20 mm x 3 mm complete welded to frame with one vertical mullion of EWR bolt 'T' section of size 60 mm x 25 mm and 1.25 mm thick including cuttings holes and making good dismantled portion for each window including following fittings welded to failed shutter:- (a) Holdfasts 150 mm long 12mm x 3 mm made to shape- 4 Nos per window (b) Handle of Z sec 20 mm x 25 mm, 100 mm long - 1 No per leaf. (c) MS tower bolt 150 mm long - 2 Nos per leaf. (d) 'Z' sec 20 mm x 25 mm, 100 long stopper-01 No per leaf, (e) Cleat 55mm long of hollow square 15 mm x 20 mm x 63 mm welded to hinges - 1 No per leaf | (1) MS pintal hinges of size 75 mm x 12 mm - 2 Nos per leaf. (g) fabriction and fixing arrangement complete. Note:- Grill / guard bars, glass pane shall be measured and Paid for seperately.

Taking down carefully existing points wiring on surface conduit/concealed conduit for light/fan/socket/power/bell from wall & roof along with fitting and fixtures such as switches, sockets, ceiling roses, batten holders, unserviceable light fittings, piece of wires, gutties, conduit, wooden boards etc and making good the disturbed portion of all floor, ceiling etc all as specified and directed.

M&L for point wiring with 1.5 sqmm (22/3mm) PVC insulated and unsheathed FRLS single core stranded copper conductor for one light/fam and including metallic rigid concealed conduit medium grade 19/20 mm dia to be terminated in pressed steel terminal boxes with top cover plate including 1.5 sqmm (22/3mm) PVC insulated and unsheathed FRLS single core stranded copper earth continuity conductor controlled by one switch and/or one regulator complete including repairing the surfaces in CM 1:3 and finishing the surface as per existing treatment all as specified and directed (switches and regulators shall be measured and paid for seperately) (Wiring shall be done as per colour code as per IS for phase, neutral and earth).

All as per item No. 40 above here-in-before but one 5 Amps socket point on independent board but with other switches complete all as specified and directed.

All as per item above here-in-before but one socket out let 5 pins 5 Amps on the same board but with other switches complete all as specified and directed.

All as per item above here-in-before but one socket out let 3 pins 15 Amps independent with 2.5 sqmm wire including 1.5 sqmm PVC insulated and unsheathed FRLS single core stranded copper earth continuity conductor complete all as specified and directed.

S&F switch piano 1 way, 6 Amps, ISI marked complete all as specified and directed.

S&F switch piano 1 way, 16 Amps ISI marked complete all as specified and directed.

S&F socket piano 5 pin 6 Amps ISI marked complete all as specified and directed.

S&F socket piano 5 pin6/16 Amps combination type ISI marked complete all as specified and directed.

S&F ceiling rose surface bakelite surface 65x50 mm 3 terminals all as specified and directed.

S&F lamp holder incl flexible wire 0.5 sqmm copper cable all as specified and directed.

S&F tube light fitting LED type retrofit T-8, 20 watt, 4 Ft long incl LED tube rod and incl 3 core flexible wire 0.5 sqmm copper cable all as specified and directed.

S&F MCB DB double door 240 Volts with 200 Amps standard bus bar of suitable size and comman neutral link all enclosed in standard sheet flush mounting type, drilling holes for incoming and outgoing cables complete suitable for 12 ways with IP-42 protection complete all as specified and directed.

S&F MCB TPN, 4 pole, 415 volts, 40 Amp, 16 KA rupturing capacity for fixing in DBs of including proper thimble connections complete all as specified and directed.

S&F MCB, single pole 240 Volts 6 to 32 Amps capacity fixing in DBs including proper thimble connections complete all as specified and directed.

S&F LED security light fitting 35 watt, complete with all accessories internally pre wired and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed.

S&F LED bulb 12 watt of approved make complete all as specified and directed.

Supply, laying and testing cable XLPE 16 sqmm 4 core insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (Heavy duty) 1100 volts grade with stranded aluminium conductor of size complete all as specified and directed.

Excavatinig in trenches, n exc 1.5 m wide and n.exc 1.5m in depth for foundation, etc. or for shaft, wells, cesspits, manholes, pier holes etc. n.exc. 10 sqm on plan and not exc 1.5m in depth and getting out soft/disintegrated soil complete all as specified and directed

Returning and filling in trenches, spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick complete all as specified and directed

Removing excavated material/surplus soil and depositing where directed at a distance not exceeding 50 mtr at a level not exc 1.5 mtr from starting point complete all as specified and directed.

Supplying, laying/spreading in trenches, river sand, clean, including spreading, levelling, punning for laying/cushioning of cables all as specified and directed. Note :- Punning thickness of sand shall be measured for payment.

Supply lay in trenches fly ash brick, old size sub class 'B' for cable protection all as specified and directed.

Supply and fix on pole/wall or lay in trenches under road/drain crossing etc, for drawing cables, GI pipe light grade ISI marked of 50 mm bore dia size including necessary pipe, fittings, clamps bolts, nuts, etc complete all as specified and directed.

M&L for Earthing complete with Galvanised MS earth plate electrode 600 x 600 x 6 mm buired directly in the ground vertically to depth not less than 3 Mtr below the ground level with the top edge of earth plate depth not less than 2.25 Mtr below the ground level connected to GI earth wire 4 mm dia by means of bolts , nuts and washers protected by GI tubing light grade 15 mm dia upto Test point 15 mm dia medium grade watering pipe with funnel & wire mesh , PCC pit in PCC 1:2:4 using 20 mm graded crushed stone aggregates chamber 40 mm thick RCC cover slab (1:2:4) type B-1 using 20 mm graded crushed stone aggregates complete all as specified and shown in electrical plate No. 3 of SSR Part-1 including earth work in any type of soil , removal of surplus soil to distance not exceeding 50 m and deposting where directed and providing charcol dust &salt layers all around the earth plate upto 15 cm all as required specified & as directed by Engr-in-Charge. Note:- 1.The rates for earthing under items includes the cost of followings: (a) Earth electrode. "(b) Main earthing lead from earth electrode to test point upto 7.5 metre" "(c) Material and labour for connecting earth electrode and earthing lead as specified." (d) Adequate quantity of charcoal dust and common salt. e) All labour involved including testing of earth net work. (f) Excavation and earth work or drilling hole for electrode. (g) P.C.C. pit and C.I. cover (h) Funnel with watering pipe, wire mesh and copper lugs etc. as specified. (j) G.I. protection pipe of size ordered specified for protection of earthing lead from mechanical injury or tempering. (k) Test point and extra length of main earthing lead beyond 7.5 metres (l) Connecting lead from test point to main switch or switch board or equipment to be earthed. 2.On testing after completion if the desired earth resistance is not obtained the earthing will be re-done at no extra cost."

M/S. Vyas Vatika Constructions co.

M/s Parmod Kumar

SP Builders

M/S VIJAY TRADERS