C/O Office building for new Jal Sgakti Sub- Division Jasuur in Tehsil Nurpur Distt. Kangra SH C/O Assistant Engineer office building, boundary wall, sanitry fitting and internal wiring)

Amount

Excavation in foundation trenches in earth work lift upto 1.5 mtr stacking the excavated soil not more than 3 mtr clear from the edge of excavation and then returning the stacked soil in 15cm layers when required into plinths sides of foundation etc consolidating each deposited layer by ramming watering and then disposing of all surplus excavated earth as directed with in all leads and lifts as per the satisfaction of the Engineer-in-charge.

Providing and laying cement concrete 1:4:8(1Cement:4Sand:8graded stone aggregate 40mm.nominal size and curing complete excluding the cost of form work of centring and shuttering in foundation and plinth within all leads and lifts as per the satisfaction of the Engineer-in-charge.

Square rubble masonry/Polygonal rubble masonry(un-coursed)brought to courses) with hard stone of approved quality in foundation and plinth including levelling up with cement concrete 1:6:12(One cement:Six sand: 12graded stone aggregate 20mm.nominal size) and plinth level in Cement mortar 1:6(One cement:6Sand) in breast walls/Retaining walls within all leads and lifts as per the satisfaction of the Engineer-in-charge.

Filling in plinth with sand under floor within all leads and lifts as per direction of Engineer-In-Charge.

Providing form work with steel plates 3.15mm.thick welded with angle iron in frame 30x30x5mm. So as to give a fair finish including centering,shuttering and propping etc. with wooden battens and ballied height of propping and centring below supporting floor to ceiling not exceeding 4.00 mtrs. and removal of the same for in-situ-reinforced concrete and plan concrete work in:

Foundation footing & bases of columns complete in all respect as per the satisfaction of the Engineer-in-charge

Sloping or vattering surfaces including folded plates where inclination to horizontal plane and the like within all leads and lifts as per the direction of Engineer-in Charge.

Flat surfaces such as soffits of suspended floors, roofs, landing and the line floor etc upto 200mm thickness complete in all respect within all eads and lifts as per direction of Engineer-in-charge.

Beam, cantilever, girders and lintles sides and soffits of beam haunching cantilever girder, bressumers and lintles not exceeding 1 mtr in depth complete in all respect within all leads and lifts as per direction of Engineer-in-charge

Providing and laying cement concrete work 1:1.50:3 (1 cement:1.50 sand:3graded stone aggrigate 20mm nominal size) and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in:-

In foundation, footings, bases of columns and the like and mass concrete within all leads and lifts as per the directions and satisfactions of the Engineer-in-Charge.

In suspended floors, roofs, landing and shelves and their supports balconies, beams, girders and cantilever upto floor two level complete in all respect within all leads and lifts as per direction of Engineer-in-charge.

In columns pillars and posts including entire carriage of materials within all leads and lifts as per the directions and satisfactions of the Engineer-in-Charge.

Providing and laying cement concrete work in 1:2:4 (1 cement:2 sand: 4 graded stone aggrigate 20mm nominal size) and curing complete excluding the cost of form work and reinforcement for reinforced work in;-

Providing tor steel reinforcement for RCC work including bending, binding, & placing in position omplete upto floor two level.

Brick work using common burnt clay building bricks in foundation and plinth in Cement Mortor 1:6(One Cement:Six Sand)(first Class Bricks) within all leads and lifts as per the satisfaction of the Engineer-in- charge.

First class half brick masonary common burnt clay building bricks (1st class) in super structure above plinth level upto floor two level in cement mortar 1:4 (1 cement:4 sand) in all leads and lifts as per the satisfaction of the Engineer-in- charge.

Providing wood work in frames of doors, windows and other frames wrought framed and fixed in position with second class deodar wood within all leads and lifts as per the direction of Engineer-in-charge.

For doors, windows and ventilators and glazed partitions frames(Sections No. 4605)

Providing and fixing panelled and glazed shutter for doors,windows and clearstory windows including black enamelled buyt hinges with necessary screws 40mm.thick(2nd.class deodarf wood) within all leads and lifts as per the direction of Engineer-in-charge.

Providing and fixing 12 mm thick and 100 mm wide pelmet with 25 mm dia metre wooden curtain rod within all leads and lifts as per the direction of Engineer-In-Charge.

Providing and fixing MS grill of required petern in wooden frame plain grill within all leads and lifts as per the direction of Engineer-In-Charge.

Providing & fixing wire gauge shutters using galvanized MS wire gauge of IS gauge designation 85 G. with wire of dia. 0.56 mm for doors,windows & clerestrey windows of 30mm thick including bright finished black enameled iron hinges with necessary screws.within all leads and lifts as per the direction of Engineer-in-charge.

Providing and fixing 40X3 mm flat iron hold fasts 40 cm long including fixing to frame with 10mm dial metres bolts and nuts and wooden plug and embending in cement mortar block 30X10X15cm 1:3:6 (1 cement: 3 sand: 6 graded stone aggrigate20mm nominal size)complete in all leads and lifts as per the direction of Engineer-In-Charg.

Providing and fixing hand rail 75X60 mm rounded hand rail in straight length complete in 2nd class deodar wood within all leads and lifts as per the direction of Engineer-In-Charge.

Providing and fixing 75X60 mm caps turned to match the hand rail the hand rails screws and dowels within all leads and lifts as per the direction of Engineer-In-Charge.

Providing and fixing 25+25 mm balusters 25X25 mm rod fixed with ends housed to hand rails and treads or strings complete in first class deodar wood within all leads and lifts as per the direction of Engineer-In-Charge.

Providing and fixing bright finished aluminium sliding door bolts with bolts and nuts necessary screws etc.cmplete within all leads and lifts as per the direction of Engineer-In-Charge.

Providing & fixing bright finished aluminium tower bolt with bolts and nuts necessary screws etc.cmplete within all leads and lifts as per the direction of Engineer-In-Charge.

Providing & fixing bright finished aluminium handles bolts with bolts and nuts necessary screws etc.cmplete within all leads and lifts as per the direction of Engineer-In-Charge.

Providing and fixing bright finished brass door latch with necessary screws etc.cmplete within all leads and lifts as per the direction of Engineer-In-Charge.

Providing and fixing 100 mm bright finished door stoper with rubber cushion to suit shutter complete within all leads and lifts as per the direcion of Engineer-In-Charge.

Providing & fixing oxidized MS double ascting spring hinges with necessary screws etc.cmplete within all leads and lifts as per the direction of Engineer-In-Charge.

Providing and fixing bright finished hard drawn hooks & eves cmplete within all leads and lifts as per the direction of Engineer-In-Charge.

Providing & fixing bright finished brass fan light catch with necessary screws etc.cmplete within all leads and lifts as per the direction of Engineer-In-Charge.

Providing and laying duro stone vitrified tiles 300X300X10 mm in gray coloured or approved shade in flooring, treads of steps and landing laid on bed of 12 mm thick cement mortar 1:3 (1 cement : 3 sand) laid over and jointing with neat cement slurry finished with flush pointing in white cement mixed with pigment & required shade to match the shade of tiles cmplete within all leads and lifts as per the direction of Engineer-In-Charge.

Providing & fixing 10mm thick anti skid water proof stain and impect resistant heavy duty vetrified tiles nitco or equivalent 600X600X10 mm manufactured of approved shade and colour in flooring treads of step and landing & laid over 12mm thick cement mortar 1:3 (1 cement : 3 sand) laid over and jointing with neat cement slurry finished with flush pointing in white cement mixed with pigment & required shade to match the shade of tiles cmplete within all leads and lifts as per the direction of Engineer-In-Charge.

Providing & laying duro stone vitrified tiles 300X300X8 mm in grassy coloured of required shade in skirting risers of steps and dados on 12mm thick cement mortar 1:3 (I Cement : 3 sand) laid over and jointing with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete within all leads and lifts as per direction of Engineer-In-Charge.

Providing and fixing on wall face CI rain water pipes incuding filling the joints ith spun yarn and cement mortar 1:2 (1cement: 2 sand) complete 100 mm dia pipe, within all leads and lifts as per the direction of Engineer-In-Charge.

Providing and fixing on wall face CI accessories for rain water pipes incuding filling the joints ith spun yarn and cement mortar 1:2 (1cement: 2 sand) complete 100 mm dia pipe, within all leads and lifts as per the direction of Engineer-In-Charge.

Applying priming coat over new steel and other metal surface after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and scoured with wire brushes fine steel wool scraps and and sand paper complete with ready mixed priming paint brushing red lead, red oxide/ zinc oxide chrome wit all leads anmd lifts as per the direction of Engineer-In-charge.

Applying priming coat of over new wood and wood based surfaces after and including preparing the surface by throughly cleaning oil,grease,dirt and other foreign matter and coursed with wire brushing line steel wool scrapers and sand papering complete with ready mixed paint with in all leads and lifts as per the directions of the Engineer-in-Charge.

Painting two coats excluding priming coat on new steel and other metal surfaces with ready mixed paint and brushing to give an even shade including cleaning of all dirt, dust and other foreign matter with in all leads and lifts complete in all respect as per the direction of Engineer-In-Charge.

Painting two coats(excluding priming coat) on new wood and wood based surface with ready mixed paint brushing the give and even shade including cleaning of all dirt dust and other foreign matter and sand papering and stopping with ready mixed paint other than white in all leads and lifts.as per direction of Engineer-in-charge

6mm cement plaster to ceiling in cement mortar 1:3 (1cement : 3sand) complete in all respect within all leads and lifts as per direction of Engineer-in-charge

20 mm thick cement plaster in two coat on rough side of brick/stone/concrete walls for interior plastering up to floor -2 level including arrisses,internal rounded angles,chamfers and or rounded angles not exceeding 80 mm in girth and finished even and smooth with in all leads and lifts in C.M 1:6 ( 1 cement,6 sand ) with in all leads and lifts complete in all respect as per direction of Engineer-in-charge.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete in all respect as per direction of Engineer-in-charge.

Wall painting (two coats) with acrylic emulsion paint of approved brand and manufacture for interior grade on undecorated concrete/stone/plastered wall surfaces to give an even shade including t horoughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty a required for metling the surface complete in all respect as per direction of Engineer-in-charge.

Providing under layer protection 75mm thick bed of dry brick/stone aggrigate 40mm nominal size with rammed and consoildated and grouted with fine sand including preparation of ground within all leads and lifts as per the direction of Engineer-In-Charge.

Providing plinth protection 50 mm thick in cement concrete 1:3:6 ( 1 cement, 3 sand, 6 graded stone aggregate 20 mm nominal size ) with in all leads and lifts complete in all respect as per direction of Engineer-in-charge.

Providing stone kharanja drain 60cm wide including 25cm side stone lade in cement mortar 1:6 (1 cement: 6sand) with in all leads and lifts complete in all respect as per direction of Engineer-in-charge.

Stone/Boulder filling behind retaining wall under floor with in all leads and lifts complete in respect as per direction of Engineer-in-charge.

Construction of Boundary wall

Excavation in foundation trenches earth work in pick work, jumper work within all leads and lifts stacking the excavated soil not more than 3 mtr clear from the edge of excavation and then returning the stacked soil in 15cm layers when required into plinth sides of foundation etc., consolidating each deposited layer by ramming watering and then disposing of all surplus excavated earth as directed within all leads and lifts as per direction of E-in-charge.

Providing and laying cement concrete 1:6:12( 1 cement : 6 sand: 12 graded stone aggregate 40mm nominal size) and curing complete excluding cost of form work in foundation and plinth within all leads and lifts as per the direction of Engineer-in-Charge.

Squared rubble masonery coursed with hard stone of approved qualityin foundation and plinth including raking out joints in Cement Mortor 1 : 6 ( 1 Cement : 6 Sand ) complete in all respect as per the direction of engineer in charge.

Brick work using common burnt clay building bricks of approved quality in super structure above plinth level in cement mortar 1: 6 (1 cement : 6 sand) up to floor two level (1st class bricks) within all leads and lifts as per the direction of Engineer-in -Charge.

Half brick masonry with Ist.Class common clay bricks in cement mortar 1:4(One cement :Three sand) within all leads and lifts as per the satisfaction of the Engineer-in-charge.

15mm cement plaster in single on rough side of brick / concrete /stone masonery wall for interior plastering up to floor two level including arrises, internal rounded angles chamfers and or rounded angles not exceeding 80mm in girth and finished even and smoth in cement mortar 1 : 6 ( 1cement : 6 sand ) within all leads and lifts as per the direction of Engineer-in -Charge.

Providing and fixing MS grills of required pattern in boundary wall with M.S flat square or round bars with round headed bolts and nuts or by screw with in all leads and lifts complete in all respect as per the direction of Engineer-in charge.

Steel work welded in built-up section, trusses and framed work including cutting hoisting, fixing in position and applying a priming coat of red lead paint in beams joists channels, angle cleats as in main and cross beam, hip and jack rafters, purlins connected to common rafters, steel gate and like within all leads and lifts as per the direction of Engineer-in- Charge

Finishing wall with water proofing cement paint of approved brand and manufacture and of required shade on decorated wall surface ( Two coats including one subsequent coat) to give an even shade after thoroughly brushing the surface to remove all dirt dust and remained of loose powdered materials within all leads and lifts as pe the directions of the Engineer-in-Charge

Providing and laying of heavy duty precast cement concrete inter locking paver blocks vibro compacted upto M-50 grade i/c border or kurb block grey or colored over sub-base of concrete with 25mm thick average thickness of cement mortar 1:4 (1cement : 4 sand) laid jointed with neat cement slurry mixed with pigment to match the shade of blocks i/c curing rubbing & polishing complete in all respect as per the direction of Engineer-in charge..(Sub base concrete floor to be paid for seperately)

Sanitary fitting

Excavation in foundation trenches in earth work lift upto 1.5 mtr stacking the excavated soil not more than 3 mtr clear from the edge of excavation and then returning the stacked soil in 15cm layers when required into plinths sides of foundation etc consolidating each deposited layer by ramming watering and then disposing of all surplus excavated earth as directed with in all leads and lifts as per the direction of Engineer-in charge.

Providing and fixing of sand cast/ cast iron spun spigot and socket soil, waste and ventilating pipe(Lead chaulked joints to be masured and paid for seperetaley)complete in all respect as per the direction of Engineer-in charge.

100mm dia soil wast upto Septic tank

75mm dia waste water

Providing and fixing of cast iron fittings and accessories bends of required of required degree complete in all respect as per the direction of Engineer-in charge.

Plain Bend

75 mm dia

100 mm dia

Door Bend

75 mm dia

Door Tee

100 mm dia

Providing and fixing of lead chaulked joints to pun iron or CI pipes and other fittings i/c floor traps etc. including testing but excluding the cost the cost of lead complete in all respect as per the direction of Engineer-in charge.

75 mm dia

100 mm dia

Providing and fixing of cast iron holder bats i/c steel bolts to sand cast iron/cast (spun) iron pipes in & i/c C.Conc. Blocks 100x100x100 mm of 1:2:4 mix (1 Cement: 2 Sand : 4 graded stone aggrigate 20 mm nominal size) i/c cost of cutting & making good the wall embeded complete in all respect as per the direction of Engineer-in charge.

75 mm dia

100 mm dia

Providing and fixing of CI floor traps to self cleaning desing with sand cast iron screwed down orhinged grating with or without vent arm complete i/c cost of cutting and making good the walls complete in all respect as per the direction of Engineer-in charge.

75 mm dia

Providing and fixing of CI slotted vent cowl.

100 mm dia

Providing and fixing of vitarous china water closet squatting pan (Eropean type WC pan) with intergal P or S trap including jointing the trap with soil pipe in cement mortar 1:1 (1 Cemenr : 1 Sand) including Seat cover and jet pressure Pipe complete in all respect as per the direction of Engineer-in charge.

Providing and fixing 10 ltrs. vitreous China low level flushingcistern with a pair of M.S. brackets complete with all accessories including fixing the over flow pipe and handles etc. complete (White color) complete in all respect as per the direction of Engineer-in charge.

Providing and fixing vitreous China padedstal for wash basin with single hole for piller tap/ mixture with MS brackets i/c cutting holes and making good the surface FLAT BACK 550x400 mm.complete in all respect as per the direction of Engineer-in charge.

Providing and fixing vitreous China padedstal for wash basin complete recessed at the back for the reception of pipes and fittings complete in all respect as per the direction of Engineer-in charge.

Providing and fixing of CP brass waste for wash basin or sink 32mm dia complete in all respect as per the direction of Engineer-in charge.

Providing and fixing M.I. Union for wash basin or sink :-32mm dia complete in all respect as per the direction of Engineer-in charge.

Providing and fixing of lead waste pipe 32mm dia for wash basin and sink including brass check out complete in all respect as per the direction of Engineer-in charge.

Providing and fixing 600mm x 450 mm bevelled edge miror of superior glass mounted on 6mm thick A.C. Sheet or plywood sheet and fixed to wooden plugs with C.P. Brass screws and washers complete in all respect as per the direction of Engineer-in charge.

Providing and fixing C.P. Brass Towell rail complete with C.P. Brass brackets fixed to wooden pluges with C.P. Brass screws :-600mmx20mm complete in all respect as per the direction of Engineer-in charge.

Providing and fixing charomium plated brass soap dish with C.P. Brass brackets fixed to wooden cleats with C.P. Brass screws complete in all respect as per the direction of Engineer-in charge.

Providing and fixing C.P Brass bib tap with Capstan head 15mm dia.complete in all respect as per the direction of Engineer-in charge.

Providing and fixing Brass stop cocks : 15mm dia.complete in all respect as per the direction of Engineer-in charge.

Providing and fixing CP brass angle15mm without nuts and pipe 15mm dia.complete in all respect as per the direction of Engineer-in charge.

Providing and fixing of CP piller tap for wash basin 15mm dia complete in all respect as per the direction of Engineer-in charge.

Providing and fixing of PVC connections heavy duty with brass union and reinforced PVC pipe.complete in all respect as per the direction of Engineer-in charge.

Providing and fixing to wall ceiling and floor galvanised mild steel tubes (heavy grade) tube fitting and clamps including making good the wall, ceiling and floor:-

Providing and fixing of 100mm dia brass CP greating hinged type and 32mm hole for waste pipe inletcomplete in all respect as per the direction of Engineer-in charge.

Constructing brick masonary chambers for underground CI inspection chamber and bends with commom burnt clay building bricks in CM 15 CI cover with frame light duty 455 x 610 mm internal dimensions total weight of cover with frame to be not less than 23Kgs (weight of cover 16 Kg and weight of frame 7 Kg ) RCC top slabs with 1:2:4 mix( 1 cement : 2 sand : 4 graded stone aggrigate 20mm nominal size ) foundation concrete 1:5:10 ( 1 cement : 5 sand : 10 graded stone aggrigate 40mm nominal size ) inside plaster 15mm thick with cement mortar 1:3 (1 cement : 5 Sand ) finished smooth with a floating coat of neat cement on walls and bed concrete etc.complete in all respect as per the direction of Engineer-in charge.

Inside dimensions 455 x 610 and 450 mm deep for single pipe line.

Providing and fixing PVC water storage tank of ISI : 12701 marked,G.I. inlet and outlet connection, 15mm nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting upto all heights above ground level complete in all respect as per the direction of Engineer-in charge.-

Electrical Wiring

Wiring for light point/ Fan point /exhaust fan point/callbell point with 1.50 sqmt PVC insulated heat resitent flame retradent (HRFR) AND Low smoke single core flexible copper conductor cable in surface recessed PVC Conduitand earthing thrlight point 1.50 sqm HRFRIS/PVC insulated core copper conductor cable as required. in surface/recessed PVC conduit as required.Guroup A.

Wiring for light plug with 2x1.50 Sqm PVC insulated heat resistant (HRFR) and low smoke single core (flexible) copper conducter cable in surface/recessed PVC conduit along with 1no 1.50 Sqmm HRFRLS/PVC insulated cable for earthing as required complete in all respect as per the direction of Engineer-in charge.

Supplying and fixing metal box of following sizes (Nominal Size) on surface/recess for fixing suitable size phenolic laminated sheet cover in front including painting etc. as required complete in all respect as per the direction of Engineer-in charge.

180mmx100mmx60m deep

Wiring for power plug with 2x4Sq.mm PVC insulated heat resistant flame retardant(HRFR) and low smoke single core (flexible) copper conducter cable in surface /recessed PVC conduit along with 1 No. 4Sq.mm HRFRLS /PVC insulated single core copper conducter complete in all respect as per the direction of Engineer-in charge.

Wiring for power plug with 2x4Sq.mm PVC insulated heat resistant flame retardant(HRFR) and low smoke single core (flexible) copper conducter cable in surface /recessed PVC conduit along with 2 No. 4Sq.mm HRFRLS /PVC insulated single core copper conducter complete in all respect as per the direction of Engineer-in charge.

Wiring for circuit / sub main with following size heat resistant flame retardent (HRFR) and low smoke single core (flexible) copper conducter cable in surface /recessed PVC conduit along with 1 No. 4Sq.mm HRFRLS /PVC insulated single core copper conducter cable of same size for earthing as required.complete in all respect as per the direction of Engineer-in charge.

2x1.50 Sq.mm

2x4 Sq.mm

2x6 Sq.mm

2x10 Sq.mm

Supplying and errection of 6Amp. To 32Amp rating 10KA breaking capacity, 240 volts, "C" curves, miniature circuit breaker of following poles in the existing MCB DB complete with connections etc. as required complete in all respect as per the direction of Engineer-in charge. (Single Pole)

Supplying and errection of 40/50/60 Amp rating 10KA breaking capacity, 240 volts, "C" curves, miniature circuit breaker of following poles in the existing MCB DB complete with connections etc. complete in all respect as per the direction of Engineer-in charge.. (Double Pole)

MCB SP DB 8 way

MCB SP DB 12 way

MCB TP & NDB 16 way

Earthing with GI earth pipe 4.5 mtrs long and 40 mm dia.including accessories and providing masonary enclousure with cover plate having locking arrangement and waitering pipe etc. (but without charcoal or coke and salt) complete in all respect as per the direction of Engineer-in charge.

Extra for using salt and charcoal for pipe earth electrodes complete as required complete in all respect as per the direction of Engineer-in charge.

Supplying and laying 6-SWG GI wire at 0.50mtrs. Below ground level for earyth electrode conductor, including soldering etc. complete in all respect as per the direction of Engineer-in charge.

Providing and errection of fancy wall bracket containing thread type CFL lamp holders of all sizes and shapes, complete with all accessories but excluding CFL lamp including making connections, testing etc. complete in all respect as per the direction of Engineer-in charge.

Supplying and fixing of surface/recess mounting ceiling fitting of all sizes and shapes, containing one No. Thread type CFL lamp holders complete with all accessories but excluding CFL lamp including making connections, testing etc complete in all respect as per the direction of Engineer-in charge.

Ceiling fitting, surface type

Providing and fixing CFL 40W Bulb ISI Marked complete in all respect as per the direction of Engineer-in charge.

Providing, installation, testing and commessioning of ceiling fan with regulator, including wiring the down rods of standard length (upto 30cm) with 16/0.20 mm twin twisted flexible, cotton braided, copper cable, including providing and fixing phenolic laminated sheet cover on the fan box and earthing etc. complete in all respect as per the direction of Engineer-in charge.

Ceiling fan 1200 mm sweep

Ceiling fan 1400 mm sweep

Providing, installation, exhaust fan of following sizes of ceiling fan with regulator, including wiring the down rods of standard leng in the existing opening , including making the hole to suit the size of above fan, making good the damages, connections, testing and commesioning etc.complete in all respect as per the direction of Engineer-in charge.

Exhaust fan heavy duty 300 mm sweep

Supplying and fixing of folloeing way triple pole and neatral sheet steel MCB distribution board 415 volts on surface/frecess with provision for 4-pole MCB/ isolator /RCCB/RCBO as incomer and SP MCB as outgoing, complete with tinned copper bus bar, wire set neutral link, earth bar , din bar, plate detachable gland plate, cable, identification labels interconnections, phosphatized and powder painted including earthing etc.complete in all respect as per the direction of Engineer-in charge.. ( Double door 6way )

Supplying and fixing PVC conduit pipe along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit complete in all respect as per the direction of Engineer-in charge.

25mm dia

Providing and laying Single pair telephone cable with connections complete in all respect as per the direction of Engineer-in charge.

Providing and fixing electronic step type fan regulator on existing sheet for speed control of ceiling fan complete in all respect as per the direction of Engineer-in charge.

Supplying and fixing 10 Amps 240 volts, SPN indusrtrial socket outlet, 2-pole & earth, metal enclosed plug top, sheet steel enclosure, suitable to accommodate a 10 Amp SPN-MCB/DP, on surface/reccessed with chained metal cover for the socket outlet, complete with connections complete in all respect as per the direction of Engineer-in charge.

Providing and fixing call bell suitable to operate on 230 volts AC supply including connections complete in all respect as per the direction of Engineer-in charge.

Providing and fixing ding dong bell suitable to operate on 230 volts AC supply including connections complete in all respect as per the direction of Engineer-in charge.

Providing and fixing computer terminal comprising of 250x300x75 mm deep MS box phinolic laminated sheet suitable size in front with 15 amp socket P/T 1 No. 5 amp Switch P/T 3 Nos. telephone jack 1 No including connection testing commessioning etc. complete in all respect as per the direction of Engineer-in charge.

Laying of pipe for computer cable/ back filli g as required complete in all respect as per the direction of Engineer-in charge.

Provding and laying of 25mm 3.5 core armoured /XLP cable in existing pipe partialy a nd partial in ground including excavation sand cushioning, protective covering and frefilling yhe trench etc.complete in all respect as per the direction of Engineer-in charge.

Providing and laying of 10 pair telephone cable in existing PVC pipe intercom purpose as required complete in all respect as per the direction of Engineer-in charge.

ASHISH DOGRA