Provision of sheds in Cityside and Operational Cargo area at Chandigarh International Airport, Mohali.

Amount

Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to CHIAL premisses dumping ground for lead upto 1 km for all lifts, complete as per directions of Engineer-in-charge.

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. a) All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: a) 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Centering and shuttering including strutting, propping etc. and removal of form for: a) Foundations, footings, bases of columns, etc. for mass concrete

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : a) 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. a) Thermo-Mechanically Treated bars of grade Fe-500D or more.

Structural steel work revited, bolted or welded in built up sections, trusses and frame work, including cutting, hoisting, fixing in position and applying priming coat of approved steel primer all complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.a) Hot finished welded type tubes

Providing and fixing bolts including nuts and washers complete.

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer’s specifications including appropriate priming coat, preparation of surface, etc. complete. On steel work

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. a) Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Providing, fabricating, assembling and erection of pre stressed Tensile Membrane Fabric structure in desired profile as per conceptual drawing, with SERGE FERRARI pre constraint TX-30 Type III or MEHLER VALMEX FR MEHAT OPEN TYPE III or SATTLER 759ATLAS Type III TFL / TFX or equivalent, having minimum Tensile strength (Warp / Weft) 5600 / 5500 N / 50 mm & minimum tear strength (Warp / Weft) of 700 / 650 N, high concentrated PVDF top coating and PVDF coated on bottom side, polyester fabric and should be weldable having a minimum weight of 1050 gm/sqm with a minimum 20 years warranty etc. of approved colour over steel structure frames (underneath steel structure shall be paid separately) with all fittings and fixtures such as Galvanized MS End Plate, Shackles, Rigging Screws, Turnbuckles, swedge, fork, keder rods & galvanized MS strands with stainless steel end terminals complete as per Drawing / Detail & as per particular / technical specifications and as per the directions of Engineer-in-charge. (Rate includes cost of fabric, patterns, forming, cutting, fabrication, hot weld stitch of fabric, Transport to the site, assembling and installation with GI strands, hardware, EPDM gasket and required accessories wherever required complete including lifts up to all heights, tools & plants, and necessary scaffolding etc. required for all operations in all respect as per direction of Engineer-In-Charge. Note : i) Actual plan area of canopy shall only be measured for payment. Note:- Work will be executed by Specialised Agency having experience in executing similar nature of works

Providing Engineering Consultancy services for steel structure for tensile fabric roofing structure, RCC foundation work testing for load bearing capacity with all relevant calculation sheet and design vetted by IIT/NIT, detailed construction drawing required during execution etc. as specified in tender document and any other details related to consultancy work which are essential for successful execution of works etc completes as per direction and satisfaction of Engineer- In-charge.

RRCONSTRUCTION (BID ID -851222)

Proficio Engineering And Construction Pvt. Ltd. (BID ID -851181)

SAMEER GLAZING SYSTEM PRIVATE LIMITED (BID ID -844275)