Loading
Loading…
Loading…
Tender Value
₹3.9 Cr
EMD Value
₹7.8 L
Closing Date
9 Apr 2026, 3:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Revenue
WORKS
16 conditions · 4 needing a document upload
Financial Eligibility Criteria:- The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB , along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
All rates are inclusive of GST and bidders should be registered in GST.
Technical Eligibility Criteria: (a) The tenderer must have successfully completed or substantially completed (Which should have been issued not prior to 60 days of date of invitation of present tender) any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited:(i) Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii) One similar work costing not less than the amount equal to 60% of advertised value of the tender.
Note for Item 10.1: Work experience certificate from private individual shall not be considered. However, in addition to work experience certificates issued by any Govt. Organisation, work experience certificate issued by Public listed company having average annual turnover of Rs 500 crore and above in last 3 financial years excluding the current financial year, listed on National Stock Exchange or Bombay Stock Exchange, incorporated/registered at least 5 years prior to the date of closing of tender, shall also be considered provided the work experience certificate has been issued by a person authorized by the Public listed company to issue such certificates. In case tenderer submits work experience certificate issued by public listed company, the tenderer shall also submit along with work experience certificate, the relevant copy of work order, bill of quantities, bill wise details of payment received duly certified by Chartered Accountant, TDS certificates for all payments received and copy of final/last bill paid by company in support of above work experience certificate.
Similar Nature of work:- " Any Track Work. "
12 conditions · 8 needing a document upload
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
The tenderer shall clearly specify whether the tender is submitted on his own (Proprietary Firm) or on behalf of a Partnership Firm / Company / Joint Venture (JV) / Registered Society / Registered Trust / HUF etc. The tenderer(s) shall enclose the attested copies of the constitution of their concern, and copy of PAN Card along with their tender. Tender Documents in such cases are to be signed by such persons as may be legally competent to sign them on behalf of the firm, company, association, trust or society, as the case may be.(Para 14.1 (see Page-17 of GCC, April-2022) & Tenderer shall submit the documents in support of their constitution of the firm as per Para 14 of GCC, April-2022 (See Page-17 to 19).
As per instructions please attach proforma of ANNEXURE V-A this certificate is to be given by attorney/authorized signatory/each member of partnership firm / Joint Venture (JV)/ Hindu Undivided Family (HUF) / Limited Liability Partnership (LLP) etc.) Non submission of above certificate (s) by the bidder shall result in summarily rejection of his/their bid. It shall be mandatorily incumbent up on the tenderer to identify, state and submit the supporting documents duly self-attested / digitally signed by which they/he is qualifying the Qualifying Criteria mentioned in the Tender Document. Proforma is available in uploaded documents.
Certificate of Information regarding Employment/Partnership etc. of Retired Railway Employees with the tender as per the attached Performa. As per clause No 16 (a) and (b) of GCC Part-I April 2022 corrected up to date. (As per Para 16 of GCC, April2022 (See Page-19 to 20).
Restrictions on the Employment of Retired Engineers of Railway Services Within One Year of their Retirement: As per Para 59.9, of GCC, April-2022 (see Page-91).
Certificate of NO Relative being an employee of Western Railway as per attached Performa.
The tenderer should upload the scan copy of EPFO and ESI registration number. However EPFO and ESI registration would be mandatory and documents towards EPFO and ESI registration must be submitted before execution of the agreement.
In case of Bid Security in the form of Bank Guarantee, the same should be in favor of Sr. DFM Vadodara with the tender for due performance with the stipulation to keep the offer open till such date as specified in the tender, under condition of tender. (GCC April 2022 Part I Instructions to tenderers (ITT) para 5 Bid Security (1) (a,b,c),(2) (3)(i-viii). As per ACS 2 issued vide Rly. Board letter No.2022/CEI/ CT/GCC-2022/Policy date 13.12.2022: (ii) The original Bank Guarantee should be delivered in person to the official nominated as indicated in the tender document within 5 working days before closing date for submission of bids. As pr ACS 5 RB No. 2022/CE-I/CT/GCC-2022/Policy date 20.10.2023:- Para 5(3) II The original bank guarantee should be delivered in person to the official nominated as indicated in the tender document before closing date for submission of bid.(i.e. excluding the last date of submission of bids).
The tenderer whether sole proprietor / a company or a partnership firm / joint venture (JV) / registered society / registered trust / HUF / LLP etc if they want to act through agent or individual partner(s), should submit along with the tender, a copy of power of attorney duly stamped and authenticated by a Notary Public or by Magistrate in favour of the specific person whether he/they be partner(s) of the firm or any other person, specifically authorizing him/them to sign the tender, submit the tender and further to deal with the Tender/ Contract up to the stage of signing the agreement except in case where such specific person is authorized for above purposes through a provision made in the partnership deed / Memorandum of Understanding / Article of Association /Board resolution, failing which tender shall be summarily rejected. As par Para 15 of GCC, April-2022 (see Page-19).
Maintenance period for the work is "Nil Calendar" from the certified date of the completion.
Outsourcing of Track Maintenance activities under the jurisdiction of SSE/P.Way/DB for two years.
DRM-BRC-208-OF-2025-26
DRM-BRC-208-OF-2025-26
Open
Works - General
24 Months
Vadodara, Gujarat
₹0
₹7.8 L
9 Apr 2026
18 Mar 2026
26 Mar 2026
113 items across 9 schedules · ₹3,81,20,331.39 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | For Casual/Scattered Rail Renewal work | RM | 600.00 | 38 | 22,800 |
| 2 | For Casual/Scattered Rail Renewal work | RM | 600.00 | 40.24 | 24,144 |
| 3 | Locations other than Ballasted Deck Bridge | Each | 100.00 | 507.15 | 50,715 |
| 4 | For 1.00m long fishplates | Joint | 300.00 | 129.19 | 38,757 |
| 5 | Opening and refixing of Joggled fish plates provided to weld joints/rail of any rail section under traffic to enable examination of weld/rail by departmental official nominated by Engineer In charge and lubrication of fishplates by applying departmental Grease graphite grade 'O' (IS:408) to fishing planes and bolts by departmental black oil as per procedure laid down in latest version of IRPWM, including all tools required and as directed by Engineer-in-charge. Note: 1. Grease Graphite, black oil, fish bolts, K.Oil, wire brush, required for work shall be given by department and issued at concerned SSE/PW Stores. 2.Jammed fish bolts shall be cut using chisel and hammer and replaced with new bolt. | Set | 200.00 | 56.16 | 11,232 |
| 6 | Lubrication of ERCs and its liner contact area by removal of ERCs and Metal / GFN liners in rail panel, cleaning of rust / scale of ERC, Metal / GFN liners & SGCI insert by using wire brush, scrapper / sand emery paper etc supply and application of graphite grease, as prescribed by Railway for under side of liners & corresponding area of rail foot & SGCI insert with ERCs and re-fixing the same as per procedure prescribed in latest edition of IRPWM with contractors grease and all other tools & plants complete and as directed. Note: Each ERC in this item shall constitute 1 ERC and its Liner Contact area. | ERC | 700000.00 | 5.91 | 41,37,000 |
| 7 | Removing seized ERC from SGCI inserts of existing track by using suitable approved chemicals and re-fixing after greasing of insert eye and ERC with Contractor's grease of specified quality as per provisions of IRPWM, as directed by Engineer in-charge. Note: 1.List of Seized ERC along with location shall be prepared after inspection of SSE/P.Way and marked prior to execution of this item. 2. Due care shall be taken to avoid any damage to the sleeper 3.A penalty of 50% of the basic cost of new sleeper in nearest sleeper factory shall be levied on each, if SGCI insert is broken or sleeper gets cracked in the process. | ERC | 50.00 | 54.22 | 2,711 |
| 8 | Lubrication of gauge face of rail on curves, cross overs, points & crossings, turn-in curves and at locations as required with contractor's grease graphite grade "O" IS 408 and as directed. | RM | 100000.00 | 5.45 | 5,45,000 |
| 9 | By using Contractor's Grease Graphite | Each | 20000.00 | 40.38 | 8,07,600 |
| 10 | GRSP | Each | 200.00 | 22.26 | 4,452 |
| 11 | ERCs | Each | 100.00 | 7.43 | 743 |
| 12 | Metal/GFN Liners | Each | 100.00 | 4.95 | 495 |
| 13 | Renewal of seized Plate/Rail screws on PSC Sleepers by using gas or any approved methods, duly drilling holes in broken screw and removing existing screw pieces from the holes along with existing dowels and fixing new contractor's dowels (procured from RDSO approved sources) and grouting around dowel with Epoxy materials of approved specification and refixing new Railway's rail/Plate screws duly greasing the s c r e w w i t h specified grease with all contractor's materials, consumables, tools & plants, labour with all lead, lift. Note: 1.Seized screws shall be identified and marked by JE/P.Way and verified at minimum SSE/P.Way In charge) level. 2. Due care shall be taken to avoid any damage to the sleeper 3.A penalty of 50% of the basic cost of new sleeper in nearest sleeper factory shall be levied on each, if sleeper gets damaged in the process. | Each | 50.00 | 434.73 | 21,736.5 |
| 14 | Rail section of 90R and below | Each | 50.00 | 90.32 | 4,516 |
| 15 | Rail section of 52Kg and above | Each | 50.00 | 108.38 | 5,419 |
| 16 | Sleepers up to 2.85 m length | Each | 10.00 | 651.53 | 6,515.3 |
| 17 | Sleepers of length more than 2.85 m and up to 4.20 m | Each | 10.00 | 898.16 | 8,981.6 |
| 18 | Sleepers of more than 4.20 m length | Each | 10.00 | 1,416.3 | 14,163 |
| 19 | 1 in 8½ Turnout | Set | 2.00 | 4,076.13 | 8,152.26 |
| 20 | 1 in 12 Turnout | Set | 2.00 | 4,464.56 | 8,929.12 |
| 21 | 1 in 8½ Switch Assembly | Set | 5.00 | 14,415.9 | 72,079.5 |
| 22 | 1 in 12 Switch Assembly | Set | 10.00 | 16,058.35 | 1,60,583.5 |
| 23 | Turnout sleepers of length up to 2.85 m | Each | 20.00 | 147.2 | 2,944 |
| 24 | Sleepers of length more than 2.85 m and up to 4.20 m | Each | 300.00 | 176.64 | 52,992 |
| 25 | Sleepers of length more than 4.20 m | Each | 300.00 | 191.36 | 57,408 |
| 26 | Depth of 300 mm below bottom of sleeper of Plain Track | TRM | 1000.00 | 488.11 | 4,88,110 |
| 27 | Boxing and profiling of ballast as per procedure prescribed in latest edition of IRPWM including cess dressing on both sides of track. The work will include removing excess ballast from track and putting the same in crib and shoulder by leading to a maximum of 50m including crossing of track, deweeding on ballast section etc and as directed by Engineer-In charge. | TRM | 200000.00 | 28.14 | 56,28,000 |
| 28 | Under Traffic Block Conditions: | cum | 10000.00 | 56.2 | 5,62,000 |
| 29 | For PSC Sleeper | TRM | 15000.00 | 95.71 | 14,35,650 |
| 30 | For PSC sleeper Track with Sleeper Density of 1540 sleepers/Km or more | TRM | 5000.00 | 190.47 | 9,52,350 |
| 31 | Extra over Items 132011 to 132014 for working in yards | TRM | 4000.00 | 49.5 | 1,98,000 |
| 32 | With Contractor's Hydraulic Rail tensor | TRM | 7000.00 | 52.13 | 3,64,910 |
| 33 | Without Rail tensor | TRM | 10000.00 | 47.35 | 4,73,500 |
| 34 | With Clamps | Set | 50.00 | 166.97 | 8,348.5 |
| 35 | With Contractor's hard wood block. | Each | 200.00 | 1,309.31 | 2,61,862 |
| 36 | Cleaning of side drains along the track including disposing of muck beyond Railway boundary as per instructions of Engineer in- charge to keep drains clean and clear in cuttings etc. | RM | 15000.00 | 34.63 | 5,19,450 |
| 37 | Removing weeds & bushes in ballast section and cess up to 3.95m from centre line of track in mid section & station yard, as specified by Engineer in-charge including disposal of branches, bushes outside cess/yard. | TRM | 320000.00 | 15.94 | 51,00,800 |
| 38 | Kilometre & Gradient post | Each | 50.00 | 110.67 | 5,533.5 |
| 39 | LWR / SEJ Board | Each | 10.00 | 202.74 | 2,027.4 |
| 40 | Curve Post | Each | 20.00 | 118.41 | 2,368.2 |
| 41 | Curve Board | Each | 20.00 | 202.74 | 4,054.8 |
| 42 | Curve details, SE, Versine, Station Nos. etc. per station. | Each | 20.00 | 63.61 | 1,272.2 |
| 43 | Removal of screened muck discharged by FRM/SBCM where muck disposal on side slope is restricted due to platform, cutting, OHE mast etc. and disposing it beyond 5m from edge of cutting up to 3m deep or alternatively carting it up to 50m for disposing off beyond the end of cutting / platform and making up cess wherever low. | TRM | 2000.00 | 21.25 | 42,500 |
| 44 | Ballast equalisation & ballast profiling after completion of deep screening work by BCM and/or after unloading of ballast by DMT (Ballast Train), as directed by Site Engineer as per IRPWM including heaping of ballast in tamping zone keeping rails & sleeper top free from ballast, spacing and squaring of sleeper, gauging, cleaning of muck, proper fixing of fastening, attention during each round of sleeper tamping in relation to pre & post working Note: Payment shall be made only once in irrespective of numbers of TTRM packing round and after restoration of normal speed and restoration of complete ballast profile and cess profile. | TRM | 2000.00 | 39.58 | 79,160 |
| 45 | Pulling the left over ballast to the shoulders and dumping excess ballast in the cribs and shoulders including boxing/profiling as per IRPWM of track together with left over stretches at fixed structures/masts immediately after FRM work, leveling the muck for making up cess and side slopes including removing and re-fixing of traction bonds during line block with all contractors labour, tools, plant, all lead, lift, crossing of track etc. complete and as directed by the Engineer-in-charge. | TRM | 5000.00 | 33.12 | 1,65,600 |
| 46 | For day time block working | TRM | 50000.00 | 20.3 | 10,15,000 |
| 47 | For night time block working | TRM | 120000.00 | 22.76 | 27,31,200 |
| 48 | Removing and refixing of guard Rails over slab bridges during machine packing with all contractor's men and materials duly removing fittings, leading guard rails to bridge approaches, lifting, dragging, positioning and crossing of track etc, and as directed by Engineer In charge. | TRM | 2000.00 | 112.28 | 2,24,560 |
| 49 | 1 in 8½ Turnouts (Under Traffic Block Conditions) | Set | 10.00 | 9,996.74 | 99,967.4 |
| 50 | 1 in 12 Turnouts (Under Traffic Block Conditions) | Set | 30.00 | 11,639.19 | 3,49,175.7 |
| 51 | Derailing Switch (Under Traffic Block Conditions) | Set | 5.00 | 3,655.41 | 18,277.05 |
| 52 | BCM/FRM/UNIMAT (7.5 KVA generator and 12x500 W) | Night | 30.00 | 5,082.83 | 1,52,484.9 |
| 53 | CSM / DUO / 3X with or without DGS (7.5 KVA generator and 8x500 W) | Night | 100.00 | 4,601.17 | 4,60,117 |
| 54 | 60 Kg - 110/90 UTS - Outside Track | Each | 50.00 | 242.54 | 12,127 |
| 55 | 60 Kg - 110/90 UTS - On Running Line | Each | 100.00 | 310.82 | 31,082 |
| 56 | Outside Track | Each | 50.00 | 61.48 | 3,074 |
| 57 | On Running Line | Each | 50.00 | 78.7 | 3,935 |
| 58 | Drilling holes of specified size for bond holes with 7.2mm dia drill twist to correct spacing and location on 60kg/52kg rails on cess or under traffic block with contractor's tools and plant, equipment, consumable, labour etc complete as directed by the Engineer in charge at site. | Each | 50.00 | 44.75 | 2,237.5 |
| 59 | Sleeper Spacing, Re-spacing / Squaring of sleeper by Hydraulic Sleeper Spacer with contractor's tools & plants, equipment, consumable with all lead & lift etc. complete, as directed by Engineer in-charge. Hydraulic Sleeper Spacer shall be as per RDSO's Specification No. TM/SM/17, dated 31.03.1992. | Each | 500.00 | 75.84 | 37,920 |
| 60 | Measuring of Toe Load of ERC during service i n field by Electronic Toe Load Measuring Device with contractor's tools & plants, equipment, consumable with all lead & lift etc. complete, as directed by Engineer in- charge. Electronic Toe Load Measuring Device will be as per RDSO's Specification No.TM/SM/ETLMD/218 dated 13.9.2012. | Each | 1000.00 | 4.69 | 4,690 |
| 61 | Extraction of jammed ERC by Heavy Duty Hydraulic Extractor with contractor's tools & plants, equipment, consumable with all lead & lift etc. complete, as directed by Engineer in-charge. Heavy Duty Hydraulic Extractor for jammed ERCs (10 Ton capacity) shall be used as per RDSO's Specification No. TM/SM/6, dated 8.05.1991. | Each | 50.00 | 36.81 | 1,840.5 |
| 62 | For lead up to 500 metre. | MT | 30.00 | 410.32 | 12,309.6 |
| 63 | For lead beyond 500 metre and up to 1 Km. | MT | 30.00 | 529.6 | 15,888 |
| 64 | For lead up to 500 metres | MT | 30.00 | 319.49 | 9,584.7 |
| 65 | For lead beyond 500 metre and up to 1 Km | MT | 30.00 | 474.19 | 14,225.7 |
| 66 | Rails, switches, crossings, SEJ, Glued Joints, Check Rails etc. | MT | 50.00 | 478.8 | 23,940 |
| 67 | All type of PSC sleepers | MT | 50.00 | 516.47 | 25,823.5 |
| 68 | P.Way fittings of all types and other similar loose items | MT | 50.00 | 414.33 | 20,716.5 |
| 69 | Level crossings with asphalted road surface | Sqm | 300.00 | 607.68 | 1,82,304 |
| 70 | Level crossings with concrete blocks road surface | Sqm | 50.00 | 551.86 | 27,593 |
| 71 | Providing Rail Barricading with rails supplied by Railways with verticals provided at every 1.5m interval, height of barricade being up to 1.5m above ground / termination level and one or more row of horizontal rail, duly cutting rails and drilling holes as required, assembling necessary accessories to required length, including earthwork excavation for foundation, fixing posts in cement concrete 1:3:6 base of size 0.45m x 0.45m x 0.60m and one coat of red oxide painting of steel work. Note: 1. Excavation and concrete work will be paid separately. 2. Rail shall be made available within 250 metres | MT | 10.00 | 1,819.44 | 18,194.4 |
| 72 | Removing existing Channel/H-Beam sleepers with fittings from the running track under traffic block for TBTR & stacking the same neatly at specified places with contractor's tools & labour, as directed by Engineer in- charge. | Each | 5.00 | 299.31 | 1,496.55 |
| 73 | Involving Rubber Pad | Each | 50.00 | 62.55 | 3,127.5 |
| 74 | Not involving Rubber Pad | Each | 50.00 | 34.64 | 1,732 |
| 75 | Clearing waterway of major & minor bridges by removing weeds / shrubs / bushes, removing silt deposit, filling scours, if any up to 10 metre from centre of bridge on either side including disposing waste and silt away from waterway. Note: Rate is for a single line and per metre of bridge span. | Metre | 200.00 | 228.69 | 45,738 |
| 76 | Tightening of steel channel sleeper fittings i.e. hook bolts, running rails bolts, guard rail bolts on girder bridges with contractor labour tools, plants etc., including oiling, greasing of fittings complete and as directed by engineer in charge. Note: Before execution of work specific approval of ADEN to be obtained by duly indicating the locations with specific reasons along with date of last tightening done. | Sleeper | 50.00 | 46.4 | 2,320 |
| 77 | Caution Indicator Board of size 1400mmx400mm with back support frame fixed to vertical post of MS angle of size 50mmx50mmx6mm of 3650 mm long | Each | 20.00 | 6,908.11 | 1,38,162.2 |
| 78 | Speed Indicator Board of equilateral triangular shape having each side of 1000mm with back support frame fixed to vertical post of MS angle of size 50mmx50mmx6mm of 3650 mm long | Each | 70.00 | 5,917.1 | 4,14,197 |
| 79 | Termination Indicator Board of Circular shape having diameter of 1000mm with back support frame welded to vertical post of MS angle of size 50mmx50mmx6mm of 3950 mm long | Each | 45.00 | 8,361.59 | 3,76,271.55 |
| 80 | Manufacturing, supplying and fixing Curve Indicator / Point Indicator / SEJ Boards to be provided at various locations on formation, made out of MS sheet 2mm thick of size 450mm x 300mm duly fixed with MS frame of 25mm x 25mm x 3mm angle welded to 50mm x 50mm x 3mm MS angle, 1000mm long post split and bent 100mm at bottom end with all lead & lift as per specification and including painting of details with enamel paint, as directed by Engineer in-charge (Earthwork & concreting will be paid separately) | Each | 90.00 | 1,171.89 | 1,05,470.1 |
| 81 | Supply and fixing in position pre-cast cement concrete Fouling Mark as per approved drawing at station yard, duly painting the top surface and slopes with white enamel paint in two coats and inscribed letters with black of Fouling Mark, complete in all respects with all labour, materials including cement, tools and plants etc. | Each | 20.00 | 525.14 | 10,502.8 |
| 82 | For Removing | Each | 10.00 | 248.86 | 2,488.6 |
| 83 | For Fixing / Re-erecting | Each | 10.00 | 248.86 | 2,488.6 |
| 84 | Breaking the damaged PSC sleepers including dragging, if required duly removing inserts safely and handing over inserts to Railways at Stores or Depot of SSE/P.Way, including disposing the broken concrete pieces, as directed by Engineer in- charge. Released HTS wire shall be the property of Contractor. | Each | 50.00 | 11.63 | 581.5 |
| 85 | Fixing vertically the unserviceable PSC sleepers at locations of tress-passing, railway boundary or to make temporary store by excavating trench, fixing PSC sleeper in trench and filling back open trench. | Each | 200.00 | 161.09 | 32,218 |
| 86 | Providing and fixing Trolley Refuge of size 3.0m x3.0m on cess, placing with released unserviceable PSC sleepers and keeping them at all four sides of refuge and also placing as matting inside the refuge by keeping them in upside down position with a minimum of 14 sleepers including levelling with earth, excavation, all lead and lift, crossing of tracks, leading the sleepers with in a free lead and lift, handling etc., with all contractor's men material complete and as directed by the Engineer-in-charge. Note: Earth-work will to be paid separately under relevant item. | Each | 50.00 | 4,788.41 | 2,39,420.5 |
| 87 | JCB Backhoe Loaders 3DX Plus or similar with minimum 1.10 cum bucket capacity | Hour | 700.00 | 846.09 | 5,92,263 |
| 88 | Hydra or similar tyre mounted Pick-n-Carry crane of 12T capacity for misc. works of handling of material | Hour | 200.00 | 2,118.4 | 4,23,680 |
| 89 | Tractor with Trolley for local transportation or other misc. works. | Hour | 500.00 | 599.84 | 2,99,920 |
| 90 | Manufacture and supply of Precast Kilometer Posts of size 1.15 x 0.50 x 0.075 m in RCC 1:2:4 mix, engraving letters and leading to work spot, fixing in position with CC 1:3:6 concrete duly making pits of size as required, painting the post, writing the letters on both sides of the post with 2 coats of enamel paint of approved quality to the Railways drawings/IRPWM with contractor's materials, cement, steel, labour, tools, plant, with all lead and lifts etc., complete as per specifications and as directed by the Engineer-in-charge. Note: Excavation, Concrete and steel work will be paid under relevant items. | Each | 10.00 | 610.59 | 6,105.9 |
| 91 | Manufacture and supply of Precast gradient Posts of size 1.65 x 0.60 x 0.075 m in RCC 1:2:4 mix, engraving letters and leading to work spot, fixing in position with CC 1:3:6 concrete duly making pits of size as required, painting the post, writing the letters on both sides of posts in 2 coats with enamel paint of approved quality to the Railways drawings/IRPWM with contractor's materials, cement, steel, labour, tools, plant, with all lead and lifts etc., complete as per specifications and as directed by the Engineer-in-charge. Note: Excavation, Concrete and steel work will be paid under relevant items. | Each | 10.00 | 819.35 | 8,193.5 |
| Schedule total | ₹3,05,70,210.13 | ||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
DRMBRC208of2025-26C.pdf
ATTACHMENT
Annexure-F.pdf
ATTACHMENT
JPOSTDepartment.pdf
ATTACHMENT
PCECircular88forQualityofWorks.pdf
ATTACHMENT
IRSGCCApril-2022.pdf
ATTACHMENT
AdvancecorrectionslipNo01to11GCCApril2022.pdf
ATTACHMENT
ImplementationofContractore-MB.pdf
ATTACHMENT
Annexure-VIB.pdf
ATTACHMENT
208SpecialCondition.pdf
ATTACHMENT
Dainikkaaryanishpaadananumatipatra.pdf
ATTACHMENT
LETTERFORWORKSITESAFETYWITHAGENCIESLIKERVNLDFCCIL.pdf
ATTACHMENT
Recommendedmakermanufacturerofcivilmaterials.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .