CONSTRUCTION OF COMMUNITY Hall AT T. P. S. No. 5 (City Wall Improvement) (Section - 7) Final Sanc., F. P. No. 26 Ahmedabad, near dariyapur Darwaja central zone.

5 30.00 Extra above over item of boring to the rates of bore holes

of 3.5 mtr if bore are made deeper than 3.50 mtr. For a)

300 mm dia. Rmt. 539.34

6 970.00 Excavation for foundation upto 1.50 Mt depth including

sorting out and stacking useful materials and disposing

off the excavated stuff upto 50 Meters lead (B) Dense or

hard soil. Cmt. 259.14

7 970.00 Excavation for foundation 1.50 Mt to

3.0 Mt. depth including sorting out and stacking useful

materials and disposing off the excavated stuff upto

Meters lead (B) Dense or hard soil.

8 323.50 Excavation for foundation 3.0 Mt. to

5.00 Mts. depth including sorting out and stacking useful

materials and disposing off the excavated stuff upto

Meters lead (B) Dense or hard soil.

9 100.00 Filling available excavated earth (excluding rock) in

trenches, plinth, sides of foundations etc. in layers not

exceeding 20 cm. in depth, consolidating each deposited

layer by ramming and watering etc. complete.

10 10.00 Filling in foundation and plinth with murrum or selected

soil in layers of 20 cm. thickness including watering,

ramming and consolidating etc. complete. Cmt. 286.20

11 10.00 Sand filling with sand as approved by Architect in plinth /

under floor / elsewhere including watering, ramming,

consolidating and dressing to the required grades and

levels as directed by Clerk-of-Work.

12 2025.0 Anti-Termite System: Providing and laying of

0 permanent piping technology anti-termite treatment

before flooring work by installing LLDP (Low linear

density polyethylene) tube of 8 mm O.D. & 6.4 mm 1.D.

with inbuilt pressure compensation chip every 30 cm

interval in the tube, having working pressure of 2 Kg/cm2

and release rate of 1.9 Itr/hour fixed by P-clips and nails.

The LLDP pipe shall be installed at the entire periphery of

the building and at internal network of building at a depth

of 20 to 200 mm under floor at every 2 to 3 mtr. c/c

distance (adjusted as per building layout ) & Ends of loop

pass through a PVC elbow of minimum 32 mm ID at

junction box of wall and floor level, entering into a steel

reinforced grooved flexible pipe of minimum 22 mm ID

leading into junction box and the loops shall terminate in

junction boxes & test every junction during injecting

chemicals for termite control treatment. The anti termite

chemical Imidacloprid 30.5% SC mix as per IS-6313 (part

III) shall be injected by the pressure pump diluted with

water @ 10.5 ml/5 ltr of water at the rate of 2 Kg/sq.cm @

5 Ltr/SMT. The contractor shall submit approved line plan

for piping system and junction boxes dully approved by

Engineer-in-Charge with bond of 5 year warranty.(i)Anti

Termite chemical injected area (Chemical injecting incl.

labour cost) Sq. mt 133.00

13 2025.0 Carrying out timber treatment to all woodwork,

0 including drilling holes and spraying oil-based chemical

solution on the surface of timber work for termite control,

including labor and material etc., complete. Using

Chlorpyriphos20 EC as per 6313 2013 Part III (1%

concentration by mass) is recommended: one litre of

chemical emulsion diluted with 19 litres of kerosene.

Total diluted concentration will be 20 liters, inclusive of

liter chemical emulsion application in drilled holes and

0.75 / Litre chemical per one Sqmt two coat on wood

surface not protected by paint or varnish. Sq. mt 54.98

14 3100.0 Applying general insecticide pest control treatment to

0 floors, cupboards etc including labour materials etc.

complete. Using Imidacloprid 30.5 SCas Per IS 6313 part

-II( (0.075% concentration by mass) is recommended

10.5ml chemical diluted with 5 liters of water application

0.5 litre chemical /Sqm of surface is recommended as per

15 600.00 Carrying out plinth treatment to post construction /

existing structure by spraying chemical solution for

termite control treatment, including labour and material,

consistent with I.S.I specification. Using Chlordene and

Chlorpyrifos 20 EC. As Per 6131_paret-II Concentration

Weight one percent is recommended i.e one litre 20 EC

chemical emulsion with 19 liter give 1 % concrentration,

inclusive of one litre chemical emulsion application at the

rate of 5 Litre chemical / Sqm of surface is recommended

as per I.S Sq. mt 104.90

16 2690.0 Carrying out wall treatment for termite control,

0 including spraying with chemical solution in oil base,

including labour and material. Using Chlorpyriphos

ECAs per IS 6313 part- II (1% concentration by mass) is

recommended i.e one litre chemical emulsion diluted with

19 litres of oil base. Total solution will be 20 liters

inclusive of one liter chemical emulsion application at the

rate of 7.5 litres chemical / Sqm of surface is

recommended as per I.S.

17 Conveyance charge of lime , murrum, building rubbish,

earth manure or sludge, and excavated earth and fly ash

and any kind of debris etc. complete. No dry factor for

this item shall be calculated.

a 800.00 a) Upto lead of 5 Kms. Cmt. 235.51

b 300.00 b)Conveyance Charge (Extra Rate) above 5.00 Km

and Up to 10.00 Km. Cmt. 350.00

B CONCRETE AND ALLIED WORK

18 100.00 Providing and laying cement concrete 1:3:6 (1- Cement :

3 - Coarse aggregate : 6-Hand broken stone aggregates

mm nominal size) and curing complete excluding

formwork in (A) Foundation and plinth.

19 550.00 Providing and laying in situ controlled Reinforced Cement

Concrete of Mix M20 grade using cement of OPC and

20mm and down size machine crushed black trap of

approved coarse aggregate and fine aggregates confirming

to IS: 383 - 2007, by concrete batch mix plant, weight

batch machine mixed and machine vibrated design mixed

concrete, including design of concrete mix and shall be

confirming to latest IS : 456, IS : 10262 : 2009, SP23 &

SP24 with minimum cement content of 325 Kg per CUM

of concrete and if necessary adding admixtures in

recommended proportions as per IS : 9103 as retarding

admixture to retard setting of concrete and or water

reducing admixture to maintain workability with reduced

amount of water and to improve durability without

impairing strength of concrete for any type, any shapes

and any sizes of reinforced cement concrete structural

members and mass concrete such as..........for foundation,

raft, retaining wall, column, pedestals, ground/plinth

beam, beam, suspended slab, coping, wall lintel , weather

shed, chajjas, lofts, steps and waist slab of staircase,

platform, canopy, peragolas, parapet, dropwall, window

cills, mullions, facia, fins, gutter, bed block, ramp,

overhead and under ground water tank........etc., as shown

in the drawings and specifications for all sectionc in all

position for including mixing, transporting, pumping and

placing (pouring), hoisting, necessary scaffolding,

vibreting , finishing evenly, watering, levelling,

roughening and or hacking concrete at construction joints,

leaving pockets and holes, keeping drip moulds, grooves,

including curing, testing etc.with rigid and waterlight

centering and shuttering as ordinary formwork using steel

/ plywood shuttering materials for horizontal, vertical and

inclined membe of rectangular, square, round, hexagonal,

octagonal or curved shape, including necessary propping,

scaffolding, bracing, shorig, strutting, bolts, fastener nails

etc; and keeping the same in position during and after

concreting and careful stripping / careful removal of the

same at and up to appropriate time, applying approved

shuttering oils and by approved manner will prior to

placing the reinforcing steel in position to ptevent the

adhesion of concrete to form work etc. complete and as

directed and specified by PMC / ARCHITECT /

(1) The Concrete Mix Design shall be done by the

CONTRACTOR in testing laboratory approved by PMC /

ARCHITECT / ENGINEER with the Maximum Water

Cement ratio shall be limited to 0.50.

(2) The concrete design mix shall be of without mixing

/ using of Admixtures / Additives to achieve the desire

strength etc; and it shall be not paid extra.

(3) Rate EXCLUDES providing and installing

Reinforcement Steel, conduits, sleeves and inserts & form

work-Shuttering and Centering.

(4) If in Concrete Mix Design Fly Ash is allowed to use

with OPC cement - use of Fly Ash as maximum 25 % by

weight of total cementatious material to replace by Fly

Ash conforming to IS : 3812 - 2013 (Latest), than Price

Difference between OPCement and Fly Ash shall be

discounted / adjusted in next respective RA

20 273.10 -Do- as per above item but from below ground level to

Ground Floor Slab level Cmt. 12500.00

21 353.00 -Do- as per above item but from Ground floor Slab to

First Floor Slab level Cmt. 13500.00

22 307.00 -Do- as per above item but from First floor Slab to Third

Floor Slab level Cmt. 13500.00

23 313.00 -Do- as per above item but from THird floor Slab to Fifth

Floor Slab level Cmt. 13500.00

24 790.25 Extra for M

25 1005.8 Extra for M

26 142 Providing TMT Bars FE- 550 reinforcement for R.C.C.

000.00 work including bending, binding and placing in position

complete upto floor two level. Kg 75.46

27 Providing, laying and fixing in position galvalume pre

painted and pre coated (PPGA) trapezoidal profile sheets

(size, shape and pitch of corrugation as approved by PMC

/ ARCHITECT / ENGINEER) with special male / female

side laps and anti siphoning feature at male and to prevent

leakage made from high tensile strength - 345mpa /

500mpa GALVALUME steel and AZ-150gsm Zincalume

coating to total on both side as per ASTM 1397 (55%

aluminium + 43.5% zinc and 1.5% silicon) having sheet

0.55mm TCT at top and base metal thickness 0.48/0.5mm

including colour coating of 20 micron finish coat over

micron primer coat on exposed side and back coat of

microns over a primer coat of 5 microns and having

protective gard film of 25 micrones to avoid stretches

while handling the sheet and upto erection process for

roofing and side clading, approved make and approved

shade, for roofing at all levels and heights including

cutting sheets and drilling the holes with side laps as

required and end laps 150mm to 200mm including fixing

by self tapping and self drilling 8 mm dia x 55mm long

SDST screw of 'BUIDEX' orcorroshield make as per AS -

3566 class-3 with EPDM seal, washer of 25mm dia 3mm

thick bitumen washer with 6mm central hole to form

water proof joint etc. and using templates as suggested by

manufacturer to ensure proper side laps for any pitch in

horizontal and verticle or curved surface, etc. complete

and as directed and spaecified by PMC / ARCHITECT /

a 480. do as per above item but for roofing monitors from

00 mm thick Sq. mt 650.00

b 56.0 do as per above item but for roofing monitors from

0 mm thick Rmt. 775.00

C MASONARY AND PLASTER WORK

28 5.09 Brick work using common burnt clay building bricks

having crushing strength not less than 35 kg/Sq. cm. in

foundations and plinth in cement mortar 1:5 (1 cement :5

fine sand) for conventional type bricks.

29 50.0 Extra rate over above item 37 Brick work using common

0 burnt clay building bricks having crushing strength not

less than 35 kg/Sq. cm. in cement mortar 1:6 (1 cement :6

fine sand) for superstructure upto floor three level height.

For conventional type bricks. (a) For Superstructure above

plinth level upto floor two level

(B) Conventional.

30 170. Extra rate over above item 37 and 38 Brick work in super

00 structure above floor two level over and above the above

item of brick work in superstructure (B) Conventional. Cmt. 4324.00

31 50.0 Half Brick masonary in common burnt clay building

0 bricks having crushing strength not less than 35 Kg/Sq.

Cm in Cement Mortar 1:4 (1-Cement : 4- Coarse Sand) in

superstructure above plinth level for any level and

(B) Conventional Bricks. Sq. mt 633.99

32 269 Providing and applying double coat waterproof cement

0.00 plaster (mala finish) on internal surfaces in two layers,

including surface preparation, mixing approved integral

waterproofing compound, curing, scaffolding, etc.

complete.First coat: 10–12 mm thick in CM 1:4 with

waterproofing compoundSecond coat: 6–8 mm thick in

CM 1:3 with waterproofing compound (mala

finish)Finished smooth and even, true to line and level. Sq. mt 366.12

33 156 Providing and applying 15–20 mm thick stucco plaster in

7.00 cement mortar (1:3 / 1:4) in two coats, including surface

preparation, scaffolding, finishing to the desired texture,

curing, and all leads & lifts complete as per specifications.

34 156 Providing 20 mm thick double coat mala / sandface

7.00 cement plaster on brick/ concrete work for plastering

comprising of base coat of 12 mm thick cement plaster in

cement mortar (1 Cement : 4 Coarse Sand) in rough

finishing and 8 mm thick top coat of cement mortar 1:2 (1

Cement : 2 Coarse Sand) finished with trowel including

scaffolding curing etc. complete. Sq. mt 394.02

35 150 Providing and fixing 23 cms wide chicken mesh jaali with

0.00 nails & then application of 15 mm plaster on R.C.C. &

Masonary joints as per directed of Engineer in Charge Sq. mt 210.00

D STRUCTURE STEEL AND ALLIED WORK

36 143 Providing, Fabricating, Transporting and Erecting in

10.00 position at all levels as per drawing welded / bolted /

riveted steel structures with field bolting / riveting /

welding / drilling whebever necessary and finally full

welde after completting erecting work, applying one coat

of rust remover one coat of anti - corrosive red oxide paint

or yellow zinc chromate and three or more coats of

approved make and shade flat / enamle / aluminium paint

to give even shade etc, as directed and specified with

necessary gusset plates, base plates, base plates, battened

plates, cleats, etc. complete as per design and as directed

and specified by PMC / ARCHITECT / ENGINEER. (a)

Gusset plates will be measured and actual and paid for.

(b) Weight of bolts , nuts, washers, rivets and welding will

not be considered and paid for.

(c) The measurements of rolled sections shall be taken in

length and area and the weight will be computed as per

standard steel tables, Rolling margin and wastage if any

will be to contractor's account.

(d) Rate includes for any Rectifications and minor works

to be carried out etc. cpmplete. Kg 126.68

37 280 Providing and fixing M.S. grills of required pattern to

0.00 wooden frames of windows etc. with M.S. flats at required

spacings and frame alround, square or round bars with

round headed bolts and nuts or by screws. (B)

ORNAMENTAL GRILL pattis, and all other visible

wooden pattis with melamine polish of approved brand

and procedure. KG 143.64

E PAVING AND FLOOR FINISH WORK

38 75.0 Providing and laying marble stone slab flooring over

0 20mm (average)base of cement mortar 1:6 (1-cement :

coarse sand) or L.M. 1:1.5(1- lime putty : 1.5 - coarse

sand) laid and jointed with gray cement slurry including

rubbing and polishing complete. (A) Marble slab 25mm

thick Sq. mt 2267.88

39 59.0 Providing and laying polished kota stone slab 25mm thick

0 in risers of steps,skirting Dedo and pillars laid on 10mm

thick cement mortar 1:3 (1-Cement : 3 coarse sand) and

jointed with gray cement slury mixed with pigment to

match the shade of slab including rubbing and polishing

etc. complete. Sq. mt 1214.30

40 120. Providing and laying Vitrified tiles 8 to 10 mm thick , 36''

00 x 36'' in flooring treads of steps and landing laid on a bed

of 12mm thick cement mortar 1:3 (1-cement : 3-coarse

sand ) finishing with flush pointing in white cement.

41 75.0 Providing and laying Vitrified tiles 8 to 10 mm thick , in

0 skrting risers of steps and dedo on 10mm thick cement

plaster 1:3 (1-cement : 3-coarse sand) and jointed with

white cement slurry Sq. mt 1103.06

42 110. Providing and laying broken china mosaic flooring for

00 terrace using 12 mm to 20 mm broken pieces of glazed

tiles to be laid over cement mortar 1:3 to plain or slope

and to be tempered to bring mortar creme out upto surface

using white cement including rounding off junctions and

extending them upto 15 cm along the wall,clearing with

water and oxalic acid etc. as directed. Sq. mt 771.98

43 50.0 Providing and laying white or golored glazed tiles of the

0 size 300 mm x 200 mm x 8 mm / 300 mm x 450 mm x

mm in skirting, risers of steps and dedo on 10 mm. thick

cement plaster 1:3 (1 cement : 3 coarse sand) & jointed

with white cement slurry.

44 910. Providing & fixing heritage cement / Athangudi tiles in

00 COMMUNITY HALL ,EVENT HALLS, MEETING

ROOMS including base preparation, polishing & sealing Sq. mt 2250.00

45 300. Providing & fixing heritage patterned vitrified tiles

00 (Moroccan/Jaipur design) in150mm border along with

kotah stone in PASSAGES AND FOYER AREA Sq. mt 2250.00

46 450. Providing and fixing Kota stone flooring of approved

00 green and brown shades in leather finish (machine

brushed anti-skid texture), 20–25 mm thick,laid over

mm thick cement mortar bed (1:4), including dressing of

edges,jointing with cement slurry mixed with matching

pigment, curing, and cleaning and sealing is complete.in Sq. mt 1750.00

PASSAGES AND FOYER AREA

47 377. Providing and Fixing 16 mm thick Kota stone skirting of

00 100 mm height with C.M. 1:4 (1 Cement:4 Sand) in good

line and level Rmt 180.00

48 40.0 Providing & fixing 15 mm thick kadappa stone riser in the

0 STAIRCASE including polishing Sq. mt 1250.00

49 80.0 Providing & fixing 15 mm thick Jaisalmer stone steps in

0 STAIRCASE including polishing Sq. mt 1800.00

50 110 8 mm thick Vitrified Skirting (100 mm height) matching

0.00 the flooring Rmt 350.00

51 120. Providing & laying 8 mm thick vitrified tile flooring

00 complete in male female toilet area Sq. mt 1350.00

52 240. Providing & fixing 8 mm thick vitrified tile skirting

00 mm height in male female toilet area Rmt 180.00

53 39.0 Providing and fixing 12 mm thick wooden flooring on

AND GREEN ROOMS Sq. mt 4262.00

54 90.0 Providing and laying integral cement based water

0 proofing treatment Average 120 mm thick including

preparation of surface as required for treatment of roof,

balconies, terraces etc. and making necessary vata at the

junction of Wall and floor wherever required as directed

by Engineer In Charge and consisting of following

operation .Applying and grouting a slurry coat of neat

cement using 2.75 kg/Sq.Mt. Of cement admixed with

proprietary water proofing compound conforming to IS

.2645 over the RCC slab including cleaning the surface

before treatment. Laying cement concrete using broken

bricks/brickbats25 mm to 100 mm size with 50% of

cement mortar 1:5 ( 1 cement , 5 coarse sand)admixed

with proprietary water proofing compound conforming to

IS 2645 over 20 mm thick layer of cement mortar of mix

1:5 After two days of proper curing applying a second

coat of cement slurry admixed with proprietary water

proofing compound confirming to IS 2645 Finishing the

surface with 20 mm thick jointles cement mortar mix 1:4

(1 cement, 4 coarse sand) admixed with proprietary

water proofing compound conforming to IS: 2645 and

finally finishing the surface with trowel with neat cement

slurry and making of The whole terrace so finished shall

be flooded with water for a minimum period of two weeks

for curing and for final test.all above operations to be

done in order and as directed and specified by Engineer -

In- charge Sq. mt 1890.00

55 110. Providing and laying cement concrete flooring 1:2:4 (1

00 Cement : 2 Sand : 4 graded stone aggregates 20 mm

nominal size) laid in one layer and finished with a floating

coat of neat cement (A) 50 mm thick.

56 110. Providing and layingbrick bat koba concrete for china

00 mosaic bedding Sq. mt 750.00

57 100. Providing and Laying of Rubber Moulded Paver Block

00 Grey/Coloured 60 mm thick, M-35 Grade of any size ;

shape (Usually Uni-Paver Blocks) using black trap good

quality aggragate of 20 mm nominal size for footpath,

parking areas, service lanes and other areas as mentioned

in the drawing / instruction of engineer in charge. Cost

includes formworks using rubber mould,providing and

laying paver blocks as per required grading and

specification. The paver block shall be mechanically

compacted. The work of paving blocks shall be executed

in line and level by skill mason of flooring work only. It

should be laid in such a way that the no cutting of the

paver block to be necessary. if cutting of paver block

necessary then it should be cut by machine only and

carting. The finished surface of the paver block shall have

resonably good, plain finished. Paver blocks shall be

compacted and shall be relaid if necessary. Gravel or such

type of materials shall not be allowed for production.

Laying on 5 cms thick sand bedding Sq. mt 501.60

58 100. Providing and fixing pre-cast concrete kerb stone of gray

00 cement based concrete block 30 cm length x 30 cm heigh

and 75 cms thick of M-200 grade concrete as per

approved design and including excavation for fixing in

proper line and level, filling the joints in C: M 1:3 (1

Cement : 3 Fine sand) etc. complete. Rmt 328.00

F PAINT AND POLISH WORK

59 180 Providing & Applying two coat of white putty of Birla or

0.00 equivalent at all levels to internal plaster surfaces/POP

surfaces of concrete, masonry work including jambs, sills,

grooves, pattas, rounding of corners after thoroughly

brushing the surfaces free from mortar dropping and other

foreign matter and also including preparing the surface

even and sand papered smooth etc. after applying every

coat of putty. Priming coat of alkali resistant cement

primer (water or solvent based) is to be applied before at

all levels, all floors, all height, all complete as per

drawing, specifications, instruction & directions of the

Engineer-in-charge. Payment shall be done as per

drawing/laid at site of plastered area. Approved Brands :

J.K. White, Birla, Asian.

60 100. Painting two coats (excluding priming coat) on new steel

00 and other metal surface with enamel paint, brushing,

interior to give an even shade including cleaning the

surface an even shade including cleaning the surface of all

dirt, dust and other foreign matter.

61 100. Painting one coat extra on new steel and other metal

00 surface with enamel paint, brushing, interior to give an

even shade including cleaning the surface an even shade

including cleaning the surface of all dirt, dust and other

foreign matter. Sq. mt 50.40

62 150 Painting two coats (excluding priming coat) on new wood

0.00 and other wood base surface with enamel paint, brushing,

interior to give an even shade including cleaning the

surface an even shade including cleaning the surface of all

dirt, dust and other foreign matter.

63 180 Wall painting (Two coats) with plastic emulsion paint of

0.00 approved brand and manufacture on undecorated wall

surface to give an even shade including thoroughly

brushing the surface free from mortar droppings and other

foreign matter and sand papered smooth.

64 180 Finishing wall with weather proof exterior emulsion paint

0.00 on wall surface (two coats) to give an required shape even

shade after thoroughly brushing the surface to remove all

dirt, and remains of loose powdered materials.etc

complete Sq. mt 113.40

65 15.0 Providing and fixing exterior grade teak wood

0 door/window frames made from well-seasoned timber

having a moisture content of 12–15%, including

machining, rebates, mortise-tenon joints, preservative

treatment to concealed surfaces, stainless steel holdfasts,

fixing in masonry, and finishing smooth complete as per 200000.0

drawings and specifications. Cmt. 0

66 10.0 Providing and fixing teak wood external door shutters

0 of approved thickness and design including styles, rails,

panels or glazing provision, waterproof adhesive joints,

machining, sanding, preparation for hardware and

application of approved exterior wood finish complete as

per drawings and specifications. 190000.0

67 6.50 Providing and fixing carved teak wood pillar / column

including base, shaft and capital as per architectural

drawings, complete with carving work, machining,

stainless steel anchoring arrangement, preservative

treatment, sanding and exterior protective coating. 211860.0

68 3.00 Providing and fixing decorative wooden brackets /

fascia made from seasoned hardwood including shaping,

joinery, anchoring to structural support, preservative

treatment and exterior finish complete as per architectural

details. Cmt. 0

69 50.0 Wooden handrail as per design for the staircase Made out

0 of hard wood (teak,sal)with pu polish Rmt. 6000.00

H CEILING AND GLASS WORK

70 195. Providing and fixing sheet glass, selected quality (Type-

00 C) bedded in putty and fixed with wooden beading,

including the cost of wooden beadings of first-class

teakwood and necessary cutting of glass. (2) 6 mm thick.

71 21.0 Providing and fixing glazed louvered glass windows and

0 ventilators with teak wood frame 10cm. x 7cm. size

including 3 coats of oil painting to wood work

etc.complete. Sq. mt 4102.54

72 550. Providing and fixing PVC printed false ceiling with flush

00 type with alluminium frame, frame work is done with

three different sections of G.I. sheet of 24 gauge thickness

named as C, U and L. The C section is fixed with hangers

at an equal distance of 36” each and then U section is

fixed perpendicular on C section with steel screws at and

equal distance of 16” each. The complete frame work is

supported by G.I. L angle/6 mm rod hangers from the roof

and L sections is fixed all around the wall as shown in the

diagram. 5mm PVC sheet strips of size 2 wide are fixd

with counter sunk steel screws on the U section. Further

3mm PVC sheet is stuck to these PVC strips with solvent

cement such that joining lines are perfectly matched. P.U.

putty is filled, dried and leveled and requisite coats of

primer and paint is done on the ceiling for getting fine

surface finish etc. complete as per direction of

Engineering and charge manufacturer’s specification and

drawing. Sq. mt 902.00

73 550. Providing and fixing wooden planks ceiling with tounged

00 and grooved jointing and wood screws (frame work and

cover fillings to be measured and laid for separately) (A)

Indian Teak wood (iii) 25mm thick

74 15.0 Providing and fixing M.S. Fan clamps type 1 to 16mm

0 dia M.S. bar bent to shape with hooked ends to R.C.C.

slabs curing, laying including painting the exposed portion

of loops, all as per standard design complete. Eac h

130.98 11011 11.21 Extra over rate of item 20 for

providing and fixing M.S. fan clamps type-II as per

standard design in R.C.C. beams during laying towards

additional height of the clamp due to beam rib. Cm Hei

ght 1.49 11012 11.23 Providing and fixing M.S. round

holding down or anchor bolts with nuts and washer plates

complete. Each 124.74

75 550. Providing and fixing wooden false ceiling including

00 framework, ceiling boards, suspension system, finishing

and all complete as per drawings and directions of

Engineer-in-Charge.Framework to be fixed true to line,

level and plumb. Grid spacing 600x600 mm. Boards fixed

with screws. Provide cut-outs for services. Framework:

Seasoned wooden battens 50x25 mm or GI sections.

Boards: 12 mm BWR/BWP plywood. Suspension: MS

rods 6–8 mm dia. Finish: Veneer/laminate/ PU polish.

Fasteners: SS/GI screws. Sq. mt 3140.00

I GFRP AND ROOFING WORK

76 68.0 Providing and fixing Glass Fiber Reinforced Polymer

0 (GFRP) elements of approved design, shape, size, and

pattern as per drawings and instructions of the Engineer-

in-Charge.The GFRP shall be manufactured using

isophthalic polyester/vinyl ester resin reinforced with E-

glass fiber, produced through hand lay-up or spray-up

process in approved moulds.The minimum thickness of

GFRP elements shall be 5 mm, unless otherwise

specified.The outer surface shall have a UV-resistant gel

coat finish, smooth or textured as per the approved

sample. The material shall be resistant to weathering,

moisture, and temperature variations.The GFRP panels

shall be fixed over MS structural framework (minimum

40x40x3 mm) anchored to the base structure using

approved anchor fasteners. Panels shall be fixed using SS

screws, rivets, or adhesive as required.All joints shall be

properly sealed using weatherproof silicone sealant.The

rate shall include:Cost of materials, labour, moulds

Transportation, loading/unloading Scaffolding and

installation All leads and lifts Finishing and cleaning.

Complete work shall be executed as per approved

drawings and sample, to the satisfaction of the Engineer-

in-Charge.Submittals Required Shop drawings Material

test certificate Sample panel (mock-up) Sq. mt 88275.00

77 550. Stone-coated roof tiles fixing over an aluminium sheet,

00 including accessories Sq. mt 3500.00

78 110 Providing & fixing aluminium roofing sheet 0.8 mm thick

0.00 with 50 mm thick rock wool insulation, including

fasteners, sealants, overlaps, flashing, complete Sq. mt 2600.00

79 121 Providing, Fabricating, Transporting and Erecting in

00.00 position at all levels as per drawing welded / bolted /

riveted steel structures with field bolting / riveting /

welding / drilling whebever necessary and finally full

welde after completting erecting work, applying one coat

of rust remover one coat of anti - corrosive red oxide paint

or yellow zinc chromate for MS truss including erection

80 385 Providing, Fabricating, Transporting and Erecting in

0.00 position at all levels as per drawing welded / bolted /

riveted steel structures with field bolting / riveting /

welding / drilling whebever necessary and finally full

welde after completting erecting work, applying one coat

of rust remover one coat of anti - corrosive red oxide paint

or yellow zinc chromate for Purlins

81 100. Providing and fixing GI/Aluminium gutters having section

00 400 mm wide and 150 mm deep with 0.50 mm thick sheet Rmt 800.00

82 28.0 P&F PVC Downpipes of 100 mm dia 4 Kgf/sqcm

83 120. Flashing & ridge caps

84 480. Providing, laying and fixing in position galvalume pre

00 painted and pre coated (PPGA) trapezoidal profile sheets

(size, shape and pitch of corrugation as approved by PMC

/ ARCHITECT / ENGINEER) with special male / female

side laps and anti siphoning feature at male and to prevent

leakage made from high tensile strength - 345mpa /

500mpa GALVALUME steel and AZ-150gsm Zincalume

coating to total on both side as per ASTM 1397 (55%

aluminium + 43.5% zinc and 1.5% silicon) having sheet

0.55mm TCT at top and base metal thickness 0.48/0.5mm

including colour coating of 20 micron finish coat over

micron primer coat on exposed side and back coat of

microns over a primer coat of 5 microns and having

protective gard film of 25 micrones to avoid stretches

while handling the sheet and upto erection process for

roofing and side

clading, approved make and approved shade, for roofing

at all levels and heights including cutting sheets and

drilling the holes with side laps as required and end laps

150mm to 200mm including fixing by self tapping and

self drilling 8 mm dia x

55mm long SDST screw of 'BUIDEX' or corroshield

make as per AS - 3566 class-3 with EPDM seal, washer of

25mm dia 3mm thick bitumen washer with

6mm central hole to form water proof joint etc. and using

templates as suggested by manufacturer to ensure proper

side laps for any pitch in horizontal and verticle or curved

surface, etc. complete and as directed and spaecified by

PMC / ARCHITECT / ENGINEER. for roofing 0.50 mm

thick Sq. mt 650.00

85 56.0 Do as per above item but for ridge about 500 mm wide

0 having 0.50 mm thickness Rmt 775.00

J PLUMBING AND SANITARY WORK

86 SITC (Supply,Installation,Testing & Commisioning)of C

PVC (SDR-11) water supply, comprising of necessary

fittings like ,elbows ,tees, unions, reducers, coupling , pipe

nipples etc.comp. confirming to relevant ASTM D

standards necessary brass threaded male / female adaptors

or elbows necessary clamps or hangers of approved make

and made out heavy FRP channel, Zinc Coated L clamp,

G.I U clamp covered with EPDM or Silicon rubber and

Anchor fasteners etc.comp Zari cutting with el.grinder &

finishing the same in wall or floor for concealing the pipe

line jointing materials like solvent cement along with

primer base of solvent of pipe and fitting supplier's

a 25.0 20 mm dia. (NB) pipe line

b 55.0 25 mm dia. (NB) pipe line

c 75.0 40 mm dia. (NB) pipe line

d 15.0 50 mm dia. (NB) pipe line

87 Providing and Fixing PVC SWR Pipes and Fittings,

solvent fix 6kg/cm2, confirming to IS4985 and IS7834

including all fixtures such as Couplers, Elbows, Tees,

a 24.0 40 mm dia. (OD) pipe line

b 191. 110 mm dia. (OD) pipe line

c 15.0 160 mm dia. (OD) pipe line

d 10.0 200 mm dia. (OD) pipe line

88 SITC of C PVC/U PVC Ball Valve for water supply pipe

line. comprising of Jointing materials like solvent cement

along with primer base of solvent of same company make

a 2.00 C PVC ball valve of Heavy duty confirming to relevant

ASTM D standards 40 mm dia. (NB) pipe line Nos. 1000.00

89 Providing and Fixing Eurpean Type W.C. of following

a 16.0 Providing and Fixing Concealed flush tank comprising of

Providing and Fixing Concealed flush tank with upper

plate (Jaquar cat.No.JCS-JCS-WHT-2400 and Plate

Cat.no.JCP-CHR-352415)

making necessary Brick masonry wall (approx.

1000x600*150mm thick) with single coat of plaster to

concealed the flush tank with chair bracket as per

architectural design

b 16.0 Providing and Fixing ewe wall mounting suite with proper

0 line, level (Jaquar cat.No.CNS-WHT-961SPP with seat

cover) Nos. 11000.00

c 16.0 Providing and fixing Health Faucet with one metre long

0 easy flex tube in chrome finish and wall flange(cat.No -

d 16.0 Providing and fixing toilet paper holder:C.P. brass( Cat

90 Providing and Fixing Washbasin of following make and

a 13.0 Providing and Fixing wash basin above counter type

0 comprising of. Nos. 12500.00

Providing and Fixing waste coupling and Bottle trap for

wash basin (Jaquar cat.No.FLS-WHT-5601)

Making Hole for waste coupling- Pillar Cock or basin

mixer on platform

Providing and Fixing waste coupling (Jaquar cat.No.ALD

Providing and Fixing bottle trap (Jaquar cat.No.ALD

b 13.0 Providing and Fixing Pillar Cock comprising of.

Providing and Fixing Pillar Cock (Jaquar cat.No.FLR-

Providing & Fixing necessary 450mm long Braided hose

with nut and washer of Jaquar make ALD-805B

c 13.0 Providing and fixing liquid soap container (Cat No- CAN-

d 13.0 Providing and fixing PTMT towel ring. (Cat No -CAN

Providing and fixing mirror of superior glass (of approved

quality) and of required shape and size with plastic

moulded frame of approved make and shade with 6 mm

thick hard board backing :

e 13.0 Rectangular shape (Cat No - AKP-35795)

91 Providing and Fixing Urinal of following make and model

a 12.0 Providing and Fixing Sensor type urinal flushing system

0 comprising of. Nos. 21300.00

Providing and fixing white vitreous china flat back or wall

corner type lipped front urinal basin (Cat No- URS-WHT-

Providing Sensor type Urinal flushing system of jaquar

make cat. No SNR-STL-51087

Fixing sensor type flushing system at proper location with

necessary concealed box fittings etc.

b 12.0 Providing and fixing Bottle Trap (Cat No- ALD

c 12.0 Providing and Fixing waste coupling (Jaquar cat.No.ALD

92 Providing and Fixing S.S. Kitchen Sink of following make

a 2.00 Providing and Fixing Stainless steel sink made out of

1mm thick Nirali make Popular Range, Large having

Bowl size 460 x 460 x 230 mm, comprising of. Nos. 8000.00

Providing & Fixing brackets

b 2.00 Providing and Fixing wall mounted sink cock with regular

swinging spout comprising of. Nos. 2600.00

Providing and Fixing wall mounted sink cock with regular

swinging spout (Jaquar cat.No.FLR-5347N)

Providing & Fixing necessary heavy C P flange &

extension nipple heavy of Viking or Eq.make with Teflon

c 2.00 Providing and Fixing Angle Cock comprising of. Nos. 1500.00

Providing and Fixing Angle Cock ( Jaquar cat.No.FLR-

Providing & Fixing necessary heavy C P flange &

extension nipple heavy of Viking or Eq.makewith Teflon

d 2.00 Providing and fixing Bottle Trap (Cat No- ALD

93 42.0 110x110mm dia.(OD) Deep Seal P trap having water Seal

0 not less than 50mm Nos. 680.00

94 Providing and Fixing Pumps & Pressure System

a 1.00 Submersible Twin Pump System using Grundfos Make

Openwell Submersible Pumps,

2 Pumpsets (1W + 1S),Each Motor Rating : 1.5kW (2

HP), Three PhaseSystem Rating : 3.0kW (4 HP), Three

PhaseEach Pump : Flow 122 LPM @ 39 Mtr. Delivery

HeadSystem : Flow 244 LPM @ 39 Mtr. Delivery Head

Scope of Supply:Horizontal Submersible Pumpsets -

Nos., Multi Pump Controller - 1 Nos., Float / Magnetic

Sensor - 2 Nos.incl. of Material Handling &

Commissioning Charges

Controller Features:One Working One Assist Operation

With Auto Cascading (Alternating Logic) of Pumps, Over

Load / Dry Run Protection, Digital Display, On - Off

Timer & Hooter Connection

b 1.00 Pressure Booster System Grundfos Make HYPN Booster

System - Single VFD

2 Pump + Motor sets (1W + 1S),

Each Motor Rating : 1.5 kW, Three Phase, IE 3 Efficiency

System Rating : 3.0 kW, Three Phase, IE 3 Efficiency

Each Pump : Flow 10 M3/hr @ 30 Mtr. Delivery Head

System : Flow 20 M3/hr @ 30 Mtr. Delivery Head

Pump M.O.C.: Base - CI, Impeller & Chamber - SS

Scope of Supply:

Pump with Motor - 2 Nos, Pressure Transmitter - 1 Nos,

Non Return Valve - 2 Nos, Isolating Valve - 4 Nos,

Pressure Gauge - 1 Nos, Base Frame (MOC : MS, CED

Coated) - 1 Nos, Suction and Discharge Manifolds (MOC

: MS, CED Coated) - 1 Nos, Single VFD Pump Controller

- 1 Nos, 100 Ltr. Pressure Tank – 1 Nos., Dry Runing

Protection Sensor for UG tank - 1 Nos.

95 6.00 Providing and fixing in position cowl vent to pipes. (B)

75 mm diameter. Nos. 450.00

96 6.00 Providing and fixing in position cowl vent to pipes. (C)

110 mm diameter. Nos. 600.00

97 10.0 Providing and fixing 12 mm dia C.P. bib cock of approved

0 make like jaquar or Essess or any other type and make

specified by the Architect. All pillar cocks, stop cock,

angle cock etc to be Jaquar or EssEss make with quarter

turn disc ceramic cartridge and chrome finish.

98 4.00 Providing and fixign S.W. gully trap with C.I. grating

brick masonary chamber and water tight C.I. cover with

frame of 300 mm x 300 mm size (inside) with standard

weight (i) Square mouth traps. (A) 100 mm x 100 mm size

P- Type. Nos. 1997.22

99 4.00 Constructing chamber of following size including

excavation, refilling, BBCC (1:5:10) for foundation,

Cement concrete channel(1:2:4) finished with 15 mm

thick cement plaster inside in cement mortar 1:3, finished

with cement slurry, brick masonary in C.M. 1:5 and

excluding the cost of chamber seat cover etc. complete.

(ii) for size 600 x 750 mm inside clear for depth

0.00 to 900 mm for pipe dia <= 200 mm diameter.

100 500 Construction of under ground tank with 23 cm thick

00.00 Masnory wall in c.m. 1:6 incl. Excavation, necessary

cm P.C.C. in 1:4:8 for foundation and providing R.C.C.

1:2:4 for top slab ( 150 mm thick & bottom slab (120 mm.

thick). Also having 100 mm. thick R.C.C.(1:2:4) paradi on

internal face of periphery walls. Rate includes all

necessary formwork, T.M.T. steel reinforcement as per

given design, vibrating,curing, & mixing of approved

water proofing material 1 Kg. of chemical with every

Kg.bag of cement ,inside plaster in C.M. 1:3 and vatta in

C.M.1:1 inside the tank. Providing and fixing F.R.C.

frame & cover of size 600 x 450 mm , F.R.P. steps etc.

comp as directed. This includes making Two tanks of

various capacities.

101 250 Construction of overhead tank with R.C.C. 1:2:4 pardi

00.00 and top slab Rate includes all necessary formwork, T.M.T.

steel reinforcement as per given design, vibrating,curing,

& mixing of approved water proofing material 1 Kg. of

chemical with every 50 Kg.bag of cement ,inside plaster

in C.M. 1:3 and vatta in C.M.1:1 inside the tank .

Providing and fixing F.R.C. frame & cover of size 600 x

F.R.P. steps etc. comp as directed. Litre 20.00

PART -C (ELECTRICAL ITEMS)

CHAPTER - I WIRING

SECTION - 1-2 Point wiring in Copper (MODULAR)

1 Point wiring for secondary light point with 2-1.5 sq.mm &

earthwire of 1.5 sq.mm (green) both are of ISI marked 1.1 KV

grade FRLS PVC insulated multistrand copper wires, in

following type of pipe to be erected concealed in / flushed on

wall/ceiling, complete with earth continuity and necessary

connection with primary light with accessories erected on

Metal / PVC box covered with 3 mm thick PC(Polycarbonet) /

Acrylic sheet for open / concealed wiring. with necessary

Lamp holder / ceiling rose / H.D.Connector as directed.

Note:- Maximum up to 6 mtrs length, excess will be considered

as Mains for Secondary Point.

163 (a) with medium class Rigid PVC pipe and accessories Pt. 131

2 Point wiring for Light / Bell with 2-1.5 sq.mm & earthwire

of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade

FRLS PVC insulated multistrand copper wires, in following

type of pipe to be erected concealed in/ on surface on

wall/ceiling complete with 6A Modular type switch / bell push

& accessories and earth continuity of following type, erected

on PVC / Metallic box, single mounting base frame covered

with textured/metallic front plate modules erected on / in wall /

ceiling as per pipe erected, with necessary Lamp holder/ceiling

rose / H.D.Connector as directed. 0

(a) with medium class Rigid PVC pipe and accessories erected

flushed on wall/ceiling complete 0

162 Cat. III Pt. 372

3 Point wiring for FAN with 2-1.5 sq.mm & earthwire of

sq.mm (Green) both are of .ISI marked 1.1 KV Grade FRLS

PVC insulated multistrand copper wires, in following type of

pipe to be erected concealed in / flushed on wall/ceiling

complete with 6A Modular type switch and hum free EME four

or more step type electronic fan regulator with separately

mounted and accessories with earth continuity of following

type erected on PVC / Metallic box, single mounting base

frame covered with textured/metallic front plate modules

erected on / in wall / ceiling as per pipe erected. with necessary

ceiling rose / H.D.Connector as directed. 0

(a) with medium class Rigid PVC pipe and accessories erected

flushed on wall/ceiling complete 0

60 Cat. III Pt. 632

4 Point wiring for Individual Plug with & earthwire of 1.5 sq.mm

(Green) both are of ISI marked 1.1 KV grade FRLS PVC

insulated multistrand copper wires, in following type of to be

erected concealed in / on surface of wall / ceiling complete with

Modular type switch & 5 pin Plug erected on PVC / Metallic

box covered with appropriate front plate modules erected on /

in wall / ceiling as per pipe erected with following type of

[I] For 6A Plug and 6 a switch with 2-1.5 sq.mm Cu. Wire

from nearby switchboard/mcb db board 0

(a) with medium class Rigid PVC pipe and accessories erected

flushed on wall/ceiling complete 0

70 Cat. III Pt. 471

5 Point wiring for Looped Plug with 6A Modular type switch &

pin socket erected on PVC / Metallic box, single mounting base

frame covered with textured / metallic front plate modules

erected on / in wall / ceiling with following type accessories 0

79 Cat. III Pt. 255

6 Providing following type of Modular Type Accessories

mounted with pvc / metallic box, single mounting base frame

covered with textured / metallic front plate , modules erected

with necessary connection. As desired by Engineer In charge 0

(9) 16 Amp. SP one way switch 0

43 Cat.III Ea. 179

(10) 6/16Amp. Universal socket 0

43 Cat.III Ea. 198

Section :- 1- 3 / Conduits & Pipes 0

7 Providing and erecting ISI mark Medium class RIGID PVC

PIPES of following size complete to be erected on/in wall or

ceiling erected with necessary PVC fittings & Junction boxes

fixed with adhesive solution & Clamps with following dia of

pipes, in approved manner as directed 0

25 (a) 20 mm Mtr. 33

8 Providing & erecting PVC Corrugated Flexible Conduit with

required nos. of coupling, PVC bushes, Check-nuts etc.

complete of following sizes. 0

Section 1-4 Mains & Wires 0

9 Mains with 1.1 KV grade FRLS PVC insulated ISI marked

stranded Copper conductor wire in following type of pipe to be

erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm

copper conductor FRLS PVC insulated stranded wire of green

colour for earth continuity of following size 0

(a) with medium class Rigid PVC pipe and accessories 0

1500 (b) 2 wire 2.5 sq. mm (From LDB to SB and SB) Mtr. 82

10 Mains with 1.1 KV grade FRLS PVC insulated ISI marked

stranded Copper conductor wire in following type of pipe to be

erected in / on wall / ceiling with 2.5 sq. mm copper conductor

FRLS PVC insulated stranded wire of green colour for earth

continuity of following size 0

. (a) with medium class Rigid PVC pipe and accessories 0

1000 (a) 2 wire 4 sqmm Mtr. 111

11 Providing & Erecting approved make following size of TV Co-

axial flexible cable comprising inner conductor of solid bare

copper insulated with Foam PE & Secondary conductor made

of poly - Aluminium film bonded Al. Braids @ suitable

coverage overall sheathed with black PVC insulation. 0

50 (c) RG - 6 CCS Mtr. 21

12 Supplying & erecting approved make Telephone Cable

electrolytic copper conductor PE insulation twisted in two

pairs, & wrapped with FRLS PVC tape & sheathed with

FRLS PVC or HFFR outer Jacket suitable for telephone wiring

& confirming to C-DOT erected in existing pipe. of following

size of conductors & nos.of pairs. With necessary connections. 0

[A] Conductor Size 0.5 mm 0

(a) Unarmoured 0

75 (2) Two Pairs Mtr. 20

LED LUMINARIES 0

Indoor LED Fittings 0

Supplying and erecting LED indoor fittings with LEDs of

wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB,

with housing used as a heat sink shall be made of thick sheet

Steel conforming to IS: 513/CRCA/ aluminium die cast

powder coated and high U.V. & corrosion resistance with

diffuser with company mark/name 160V to 270V, Power

Factor more than 0.95, THD < 15%,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below

description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage capacity

between the ranges shown.)

Supplying and erecting LED indoor fittings with LEDs of

wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB,

with housing used as a heat sink shall be made of thick sheet

Steel conforming to IS: 513/CRCA/ aluminium die cast

powder coated and high U.V. & corrosion resistance with

diffuser with company mark/name 160V to 270V, Power

Factor more than 0.95, THD < 15%,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below

description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage capacity

between the ranges shown.)

12 (i) 5-10 Watts, Surge-2 KV, IP-20, conventional 1 to 2 feet

28 Cat-lll Ea 164

(iii) 18-20 Watts, Surge - 2KV,IP-20, conventional 4 feet

42 Cat-lll Ea 293

Supplying and erecting LED indoor fittings with LEDs of

wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB,

with housing used as a heat sink shall be made of thick sheet

Steel conforming to IS: 513/CRCA/aluminium pressure die cast

powder coated and high U.V. & corrosion resistance with

diffuser housed in aluminium casted body with company

160V to 270V,Power Factor more than 0.95, THD < 15 %,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below

description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage capacity

between the ranges shown.)

Supplying and erecting LED indoor fittings with LEDs of

wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB,

with housing used as a heat sink shall be made of thick sheet

Steel conforming to IS: 513/CRCA/aluminium pressure die cast

powder coated and high U.V. & corrosion resistance with

diffuser housed in aluminium casted body with company

160V to 270V,Power Factor more than 0.95, THD < 15 %,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below

description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage capacity

between the ranges shown.)

(A) Square/ Circular shaped Surface/Recessed Mount

Downlight with provision for spring loaded mounting clips

(i) 5-9 watts,Surge-2 KV

82 Cat-lll Ea 218

(ii) 11-15 watts, Surge-2 KV

14 Cat-lll Ea 423

(iii) 16-20 watts, Surge-2 KV

110 Cat-lll Ea 584

13 Supplying and erecting LED street light / Flood light fittings

with High power White LEDs wattage of 3 Watt and above

assembled on single MCPCB, efficiency more than 130 lm/w

and corrosion free High pressure die cast aluminum housing

with smooth finish powder coated and heat sink extruded

aluminium with diffuser and Polycarbonate optics/ lenses, with

toughened glass with company mark/name engraved or

embossed 160 to 270 V,Power Factor more than 0.95, THD <

10 %, CCT 3000 K to 5700K,Uniformity ratio >0.45,

Luminaire efficacy> 100 lumens/watt . LED driver efficiency >

85 %.( fittings required LM-79 & LM-80 certificates)(NOTE:

Below description have shown ranges of Wattage capacity of

LED fittings.The Engineer incharge may select any wattage

capacity between the ranges shown.)

(C) Post Top Lantern LED fitting comprises of finish cast

aluminum spigot and spun aluminum canopy fixed with opal

polycarbonate, pipe arrangement for vertical mounting driver

and accessories wired upto terminal block.IP

25 Cat-lll Ea 4052

(G) Step Light having Aluminium die cast and ABS Plastic

(i) 5 watts, Direct/Indirect luminaire

6-1 STREET LIGHTPOLES

Indoor LED Fittings

14 Supplying & erecting Galvanized M.S pipe post “B” class

mm O.D 4 mtr. Long duly painted with two coats of

aluminium paint complete with metallic base plate of 300 mm x

300 mm x 4mm thick for using as a compound light pole with

approx. weight 32 Kg.

15 Supplying & erecting approved make SMC press moulded

composite FRP. loop-in, loop-out approx. 2mm thick box

complete with Bakelite connector strip 5way(3P+N+E),DIN

rail for mounting mob & hinged doors as per requirement

having locking arrangements with mounting clamp with nuts,

bolts & washers suitable for erection on pole with cable

clamps& earth bolt of following size of box.

25 (B) 250mm x 200mm x 100mm [deep] Ea. 510

16 Providing 1:2:4 cement concrete foundation & 70 % PCC from

bottom including excavation for the pole of size 45 x 45 x

cm. Deep in below ground level with plinth of 45 cm x 45 cm

(or 45 cm dia x 45 cm) high upper ground level with necessary

curing and finishing in approved manner.

( for 4 & 6 mtr pole)

SWITCHGEARS & DISTRIBUTION BOARDS 0

Section 3-4 MOULDED CASE CIRCUIT BREAKERS 0

14 Providing and erecting Approved make Four pole moulded case

circuit breaker having breaking capacity ICU of 25 KA. at

V,having normal current rating up to 25 A to 100A. with Fixed

thermal & magnetic release suitable to work on A.C. supply

c/s. with all internal connections, spreader tinned copper &

complete erected in existing 16 G.M.S. housing. 0

6 ICS=100% of ICU only Cat III Ea. 6112

17 Providing and erecting Approved make Four pole moulded

case circuit breaker having breaking capacity ICU of 35 KA. at

415 V. having Normal current rating 200A.with variable

Thermal & magnetic release suitable to work on A.C.supply

c/s. with all internal connections, spreader tinned copper &

complete erected in existing 16 G.M.S.housing 0

2 ICS=100% of ICU only Cat III Ea. 16061

Section 3-8 / PANEL MOUNTING BUSBARS 0

18 Supplying and erecting triple pole & neutral 440V / 500V panel

mounting Copper Busbars with four equal Nos. of electrolyte

bus having current density not more than 1.6 Amp. / sq.mm

(Rated current / cross section area) duly wrapped with colour

insulating tape for phase sequence of following current carrying

capacity, erected with necessary bus bar supports /insulators,

main cable socket to each bar, erected in existing cubical panel

with necessary connections. 0

14 (B) Suitable for 200 Amp. capacity Rn.Mtr 3171

12 (C) Suitable for 300 Amp. capacity Rn.Mtr 4861

SECTION 3-10 / MINIATURE CIRCUIT BREAKERS 0

19 providing and erecting Miniature circuit breaker single pole 6A

to 25A suitable to operate on 240 V A.C. system and having

breaking capacity 10 KA to be erected in existing box.

confirming to IS 8828/1996 with ISI Mark 0

110 Cat.III Ea. 111

20 Providing & erecting 240 V MCB double pole switch for motor

& inductive load (C Curve) having 10 KA breaking capacity

& confirms to IS : 8828 in existing box having following

21 Providing & erecting 415 V MCB Four Pole for Motor &

Inductive Load (C Curve) having 10KA breaking capacity &

confirms to IS :8828 in existing box having following capacity 0

8 Cat III Ea. 662

12 Cat iii Ea. 730

22 Providing & erecting 415 V MCB three Pole for Motor &

Inductive Load (C Curve) having 10KA breaking capacity &

confirms to IS :8828 in existing box having following capacity 0

(a) 6 to 32 Amp. 0

23 Supplying & erecting 20 Amp 10 KA ‘C Curve’ single

pole MCB with 20 Amp. Plug socket, company fabricated

powder coated sheet steel enclosure erected as directed with

[A] Metal Clad Socket with metal clad top 0

1 Cat.III Ea. 582

SECTION 3-11 MCB DISTRIBUTION BOARDS 0

24 5 Half / One Module Blanking Plate of Standard Size. Ea. 35

25 Supplying & erecting approved make RCCB + MCB (Electro

magnetic type only) working on residual current device having

10 KA short circuit breaking capacity and 30 mAmp.

Sensitivity & 30 mili sec. tripping time conforming to IS

test knob facility trip free mechanism operating for rated

leakage at nominal ten volt, complete erected including all

materials lugs screws etc. completed.

[e] 32A to 40 A, 4 Pole Three Phase

2 Cat. II Ea. 2145

[f] 63A, 4 pole Three Phase

6 Cat. II Ea. 2806

SECTION 3-14 EARTHING 0

26 Providing and erecting required size HOT deep Galvanised iron

strip for earthing of H.T. , OCB/ ACB/ Transformer LT panel

20 board, Motors etc. using proper clamp. (25x3MM) Kg. 77

27 Providing and erecting Annealed bare Copper wire 8 to

28 Supplying & erecting in earthpit of minimum bore dia. 225mm

size ASH or approved make Safe Earthing Electrode

consisting Pipe-in-Pipe Technology as per IS 3043-1987

made of corrosion free G.I.Pipes having Outer pipe dia of

mm having 80-200 Micron galvanising, Inner pipe dia of

mm having 200-250 Micron galvanising, connection terminal

dia of 14 mm with constant ohmic value surrounded by

highly conductive compound with high charge dissipation

suitable for following type of applications. 0

[C] For Electrical Installation covering Transformer Neutrals,

Lightning arrester Earthing, A.C.Plant & Sensitive

Computer System(like Automation, SCADA)i.e.

independent Earthing located in other than normal soil i.e.

Soft Rock, Marshy Soil etc..

-Length of Pipe : 3 Mtrs.

8 -Back filling Compound :2 nos Bags of 25 Kg. Ea. 10489

SECTION 3-16 CUPBOARDS. 0

29 Providing & erecting weather proof, dust & vermin proof, floor

mounted front operated indoor type cubical panel board

necessary IP-42 and above protection as per approval from

engineer incharge made from 14 SWG thick CRC M.S. sheet

for outer body & doors, 16 SWG thick CRC M.S.sheet for

internal partitions with necessary accesories , supporting

angles/ flats channel including cutting, bending, drilling,

welding, riveting with internal partitions & cable alley as per

requirements & instruction of engineer-in-charge with erection

supplied switch gears, BUSBARS, suitable size of inter

connecting PVC copper wire / copper-aluminium strips, rubber

grommets, rib, bakelite control fuses/MCB for measuring

instruments, earth bus & earth bolts, foundation flange - bolts-

base Plates, sufficient nos. of hinged doors, handles with

locking arrangement and rubber gasket,heavy duty end terminal

connection,danger notice board,necessary ventilation,earthing

strip complete. The Panel shall be painted with epoxy powder

(The rates excludes the cost of switchgears, bus bars, inter

connecting mains & Copper Aluminium strips, meters, Fuses

etc. The dimension shall be measured excluding base beams)

The panel shall be supplied with following approved

manufacturers with following size.

(A) locally fabricated panel board 0

45 (i) with 350 mm depth Sq.Mtr 10365

SECTION 4-3 / ARMOURED ALUMINIUM CABLES 0

30 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured

cable multistrand Aluminium conductor for 1.1 KV. to be laid

on wall with necessary clamps or in existing trench / pipe of

following size of cables (VERIFY THE ACTUAL LENGTH

6 (A) 3 1/2 core 25 Sq. mm ( 16 Sq. mm 1/2 core) Mtr. 182

SECTION 4-4 / ARMOURED COPPER CABLES

31 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured

cable multistrand Copper conductor for 1.1 KV. to be laid on

wall with necessary clamps or in existing trench / pipe at road

crossing or floor of following size of cable.

60 (A) 4 core 2.5 Sq. mm Mtr. 269

50 (B) 4 core 6 Sq. mm Mtr. 505

32 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured

cable multistrand Copper conductor for 1.1 KV. to be laid

on wall with necessary clamps or in existing trench / pipe at

road crossing or floor of following size of cables.

160 (A) 4 core 10 Sq. mm Mtr. 269

SECTION 4-5 MISCELLANEOUS.

33 Making trench in soft soil of suitable width of 90 cm deep for

laying cable or locating the fault all over the run and back

300 filling the same and making the surface as normal ground. mtr 55

34 Covering of cable with second class bricks or cement tiles laid

cover the cable crosswise & also on both sides with covering of

7. 5 Cm. layer of sand above & below cable (16 bricks per

375 meter) mtr 139

SECTION 4-6 / CABLE GLANDS.

35 Providing and, fixing heavy duty flange type brass cable gland

with rubber ring for PVC insulated armoured cable complete

with out going tails, insulating tape etc for following size of

16 (\B) 2 to 4 core 2.5 / 6 Sq. mm Ea. 38

52 (C) 2 to 4 core 10 Sq. mm Ea. 38

36 Providing and, fixing heavy duty flange type brass cable gland

with rubber ring for PVC insulated armoured cable complete

with out going tails, insulating tape etc for following size of

SECTION 4-7 CABLE LUGS.

37 Solderless crimping type Aluminium lugs conforming to IS

suitable for cable of following size evenly crimped with high

pressure tool & connected to switchgear terminals with

brass/cadmium plated nut bolts in an approved manner.

38 Solder less crimping type Copper lugs conforming to IS

suitable for cable of following size evenly crimped with high

pressure tool & connected to switchgear terminals with

brass/cadmium plated nut bolts in an approved manner.

CHAPTER - V Fans and Accessories

SECTION 5-1 / CEILING FANS AND ACCESSORIES

39 Providing & erecting Approved make Ceiling Fan with double

ball bearing ISI mark with Condenser 230 volt A.C.50 Hz

1200 mm sweep complete having 3 blades aluminium body and

blade sets having ornamental design shanks , canopy erected

with earthing. [ Make shall be approved by Engineer in

60 Charge] Ea. 2289

SECTION 5-2 FAN ACCESSORIES

40 Supplying and erecting 19 / 20 mm. nominal bore Medium

Class M.S. Pipe down rod erected duly painted for fan

60 complete with proper insulation without leakage and earthing. Mtr 107

41 Supplying & erecting Fan Hook of 10 mm M.S. Round bar

60 grouted in RCC slab with Making the site as original. Ea. 43

SECTION 6-7 TIME SWITCHES

42 Supplying & erecting approved make time switch with single

pole air break contacts suitable for 230 V.15/16A.complete

with self starting motor driven clock ‘ON’ &’ OFF’ automatic

arrangement at any predetermined time during each

hours,With nickel cadmium rechargeable battery backup

3 erected as directed. Ea. 2331

43 Supplying & erecting power contactor ,AC3 duty for time

switch complete erected as per direction Cat III

3 (D) 4 pole 440V 40 Amp. Ea. 2755

LIGHTNING ARRESTER

44 SITC of Vertical Air Termination Solid aluminium with Base-

10 mm dia and 1000 mm long. Air Termination Base tested for

conditioning, Ageing Test & Lightning impulse current

withstand test: 100 kA of 10/350µs waveform in an accredited

Third party laboratory as per 6.3 & 6.4 of IEC 62561-1

protocol with MAST 34mm dia 3000 mm long- Cold

2 Galvanized Each 11000

45 SITC of Galvanized Steel Flat 25x6 mm thickness from earth

electrode directly in ground as required. Zinc coating: 500 g/m

square (Approx:70 micron coating) tested and used exclusively

for lightning protection earthing system and ring equipotential

200 bonding. Mtr 153

MARKET RATE ITEMS:-

SUB PANEL & DISTRIBUTION BOARDS

46 Supply, installing, testing and commissioning of metallic

double door type distribution board with following MCBs /

ELMCBs / RCCBs / etc. with all necessary connections,

remaining blank area shall be covered with blanking (dummy)

plates etc. complete. (All DBs shall be installed concealed in

Non-Plant Bldg.) w.r.t Technical specification

Note All MCBs & MCCBs taken in SOR

47 4-WAY VTPN DB :

Incoming : 40 A FP RCBo-30mA

Outgoing : 6 to 32 A SP MCB (12 nos) (MCB TAKEN IN

2 ABOVE SOR) Ea. 12000

4-WAY VTPN DB :

Incoming : 63 A FP RCBo-30mA

Outgoing : 6 to 32 A SP MCB (12 nos) (MCB TAKEN IN

4 ABOVE SOR) Ea. 12000

4-WAY VTPN DB :

Incoming : 63 A FP MCB

Outgoing : 6 to 32 A SP MCB (12 nos) (MCB TAKEN IN

3 ABOVE SOR) Ea. 12000

6-WAY VTPN DB :

Incoming : 63 A FP RCBo-30mA

Outgoing : 6 to 32 A SP MCB (18nos) (MCB TAKEN IN

2 ABOVE SOR) Ea. 13500

6-WAY VTPN DB :

Incoming : 80 A FP MCB

Outgoing : 6 to 32 A SP MCB (18nos) (MCB TAKEN IN

1 ABOVE SOR) Ea. 13500

8 -WAY VTPN DB :

Incoming : 100 A FP MCCB

Outgoing : 6 to 32 A SP MCB (24 nos) (MCB TAKEN IN

1 ABOVE SOR) Ea. 15000

Incoming : 160 A FP MCCB

Outgoing : 63 A FP MCB (1 nos) (MCB TAKEN IN

Outgoing : 100 A FP MCB (1 nos) (MCB TAKEN IN

SUB PANEL SF PANEL 1 (BANQUET HALL 1)

Incoming : 160 A FP MCCB

Outgoing : 63 A FP MCB (1 nos) (MCB TAKEN IN

Outgoing : 100 A FP MCB (1 nos) (MCB TAKEN IN

SUB PANEL SF PANEL2 (BANQUET HALL 2)

Incoming : 80 A FP MCCB

Outgoing : 63 A FP MCB (1 nos) (MCB TAKEN IN

Outgoing : 40 A FP MCB (1 nos) (MCB TAKEN IN

SUB PANEL TF PANEL1 (GYMNASIUM)

Incoming : 80 A FP MCCB

Outgoing : 40 A FP MCB (2 nos) (MCB TAKEN IN

SUB PANEL TF PANEL2 (RESTAURANT)

Incoming : 80 A FP MCCB

Outgoing : 63 A FP MCB (1 nos) (MCB TAKEN IN

Outgoing : 40 A FP MCB (2 nos) (MCB TAKEN IN

48 Supply, installation, testing and commissioning of OUTDOOR

water tight fitting wall washer suitable for wall mounting with

29 12 W LED lamp complete Ea 900

49 Supply and Installation of High Volume Low Speed Fan

(HVLS) 12 feet Dia., 5 blades complete. With Motor, Control

2 Panel, Controller, Mounting arrangements etc. Ea 192500

50 Supply and Installation of High Volume Low Speed Fan

(HVLS) 10 feet Dia., 5 blades complete. With Motor, Control

4 Panel, Controller, Mounting arrangements etc. Ea 172500

PART-D ( FIRE FIGHTING ITEMS)

A FIRE HYDRANT SYSTEM

Providing, laying, jointing, testing and

commissioning of following sizes of pipes

conforming to IS-1239 and IS:3589, with all

accessories like all fittings (standard M.S.

fitting with welded joint shall be used on the

pipes) including tees, elbows, reducers, union,

flanges, rubber gaskets, GI nuts bolts,

washer including supporting/fixing the pipe

1.00 on floor / wall /ceiling with clamps, hangers

(using anchor fastners) as per specification.

All hangers, clamps, brackets etc. shall be of

galvanized iron unless specified otherwire and

then supply of the same shall also be included

for rates under this head.. Welding of any

kind on the galvanized support / hanger shall

not be permitted. Arc Welding procedure as

For wet riser System - M.S `C' Heavy class

pipe (For Hydrant ,)

Providing & fixing of Single Fire Hydrant

Valve, Single Outlet, SS-304, 63 mm female

inst. oblique type, 80 mm NB flange Inlet.,

200 mm OD, 160 mm PCD, 4 holes of

1.1 4 mm, complete with C.I wheel, PVC Blank Nos.

Cap and G.I Chain, Bearing IS:5290 mark,

Painted red. Including fixing with anchor

fastner and flanged tapping from wet riser

complete as required.

SITC of Air Release Valve For Fire Hydrant

Riser, 25 mm Male BSP

Threaded, GM, Nitrile Rubber Ball And

Sheet, Minimum 1,556.00

Operating Pressure 2 Kg/Cm2 with all

Providing & fixing swinging type ISI mark,

First Aid hose reel in red colour drum with

mts long and 20 mm dia heavy duty rubber

braided water hose , terminating with SS

coupling & nozzle of 6mm outlet with shut

1.3 4 off valve confirming to IS 8090 - 1976 Nos

complete with MS socket for tap-off, drum

and brackets (including painting) for fixing on

wall with anchor fastner, bolts & nuts

conforming to IS:884-1969 complete as

Providing and Fixing of Branchpipe,

short, Stainless Steel, 63mm male inst. inlet,

Fitted with male threaded outlet,20 mm bore

1.4 4 nozzle, Nos.

bearing IS:903 mark, suitable for inter

connection to hose pipe coupling

complete as required.

Providing and fixing Hose Box lockable

cabinet, made out of MS sheet of 16 gauge

thickness having central opening and 4 mm

thick glazed glass doors (Two nos.) suitably

marked on the outside with the letters "FIRE

HOSE" including necessary locking 1,905.00

arrangement and shall be painted with one

coat of primer and two coats of synthetic

enamel paint of approved shade.(External)

Size: 750 mm x 600 mm x 250 mm.

Providing & fixing of fire brigade connection

made from SS 304 (suction collecting head)

consisting of 4 Nos. 63 mm dia instantaneous

type male couplings with built-in check

1.60 1 valves, drain valve 1 No. 150 mm dia Nos.

butterfly valve, 150 mm dia. non return valve

with flanged outlet complete with bolts, nuts

and rubber insertions as required and as per

B SPRINKLER SYSTEM

Providing, laying, jointing, testing and

commissioning of following sizes of pipes

conforming to IS-1239 and IS:3589, with all

accessories like all fittings (standard M.S.

fitting with welded joint shall be used on the

pipes) including tees, elbows, reducers, union,

flanges, rubber gaskets, GI nuts bolts,

washer including supporting/fixing the pipe

2.0 on floor / wall /ceiling with clamps, hangers

(using anchor fastners) as per specification.

All hangers, clamps, brackets etc. shall be of

galvanized iron unless specified otherwire and

then supply of the same shall also be included

for rates under this head.. Welding of any

kind on the galvanized support / hanger shall

not be permitted. Arc Welding procedure as

For Sprinkler System - M.S `C' Heavy class

Supply Installation testing & comissioning of

UL / FM approved pendent / Upright type,

chrome plated / Brass finished sprinkler, Inlet

15 NB, 68 deg.with heat activated, Quick 360.00

Response type, K-115, with required

Providing and fixing of UL listed and FM

approved flexible hose

drop with required accessories and false 1,455.00

ceilling clamps.

Supply, installation, testing and

commissioning of vertical sprinkler Alarm

Valve With Motor Gong with all required

accessories like in built drain valve, test valve, -

gauge cock and pressure gauges etc. Sprinkler

alarm valve shall be FM approved.

Providing and fixing of inspector test and

drain assembly PN 16 with sight glasss, ball

valve, union, nipple etc. Test drain assembly 2,250.00

shall be comlete in all respect.

Providing and fixing of flange ended Y

strainer PN 16 with SS scrin of

mesh/sq.inch. Flange drilling standard shall be -

Providing and Fixing of hand lever operated

butter fly valve, PN: 1.6, with CI body and

S.G disc and other working parts as per IS:

13095 - 1991. With required accessories like -

matching flange, packings etc. complete as

a 0 50 mm dia Nos.

b 4 80 mm dia Nos.

c 2 100 mm dia Nos.

SITC electrically operated water flow

switches (Vane type) including tamper switch

and accessories, complete with tap off socket

arrangement as required, with potential free

contact with 2 Nos. NONC suitable to be 875.00

fixed directly on line of the foll. diameter of

pipes including cabling till alarm panel and all

other accessories to finish the installation.

Providing and fixing of Glycrin feeled burdon

type pressure guage, made from SS working

parts and SS casing, 150 mm dial and 0-21 kg

range with calibration certificate and Shall be 810.00

fitted with shut off valve and SS 304 syphon

tube and other required accessories.

SITC of 25mm dia Air Vent Valves with

2.90 3 mm dia. Ball valve and other required Nos.

accessories like nipple, socket etc.

SITC of pressure release valve with ball valve

and accessories 3,600.00

Providing and fixing of MS support with

required anchor fasteners, insert plate etc.

2.11 1000 with one coat of zinch chromate and two caot Kg

of black enemal paint. Support shall be

complete in all respect.

C PUMP HOUSE EQUIPMENTS

Supply, installation, testing and

commissioning of electrically driven high

3.00 1 pressure centrifugal fire hydrant & Sprinkler Set

pump suitable for automatic operation

consisting of the following:

Horizontal end suction / high pressure

centrifugal pump, suitable for operation on

415 volts ± 6%, 3 phase, 50 HZ A.C supply.

The installation shall be complete with

flexible coupling and coupling guard as

required. Fire pump shall have C.I. casing,

CS diffusers, bronze impeller (hard finished

and dynamically balanced) and S.S. (304)

Shaft with mechanical seal, capable for

delivering 2280 LPM at outlet head of 70 -

MWC to ensure a minimum pressure of

Kg/Sqcm at the farthest or topmost hydrant.

The installation shall be complete with

necessary pressure gauge with gun metal shut

off cock on delivery side. (The pump should

be tested for bench mark at factory and shall

be gotten approved by the Local fire

Pump shall be capable of furnishing not less

than 150% of rated capacity at a head of not

less than 65% of the rated head. The shut off -

head shall not exceed 120% of rated head.

b. Squirrel cage induction motor, TEFC type

suitable for operation on 415 volts, 3 phase

50 HZ A.C supply, for the above pump with

synchronous speed of 2900 RPM, conforming

to IP 55 protection & class F insulation. The -

motor shall conform to IS 325-1978 (up to

date) with flexible coupling and coupling

guard, complete as required.

Common base plate for (a) and (b) from

M.S. Channel for required size. -

Suitable cement concrete foundation with

cement concrete plaster (design and drawing

to be provided by the Contractor while the

foundation will be done by others) complete -

with anti-vibration arrangement of cushy foot

Supply, installation, testing and

commissioning of Diesel Engine driven fire

3.10 1 pump suitable for automatic operation Set

comprising of the following and conforming

to BS 649/IS 10002 all amended upto date.

Horizontal, End section, Back pullout

centrifugal pump, suitable for operation on

415 volts ± 6%, 3 phase, 50 HZ A.C supply.

The installation shall be complete with

flexible coupling and coupling guard as

required. Fire pump shall have C.I. casing,

CS diffusers, bronze impeller (hard

a finished and dynamically balanced) and

CS shaft with mechanical seal, capable for

delivering 2280 LPM at outlet head of

MWC minimum pressure of 3.5 Kg/Sqcm at

the farthest or topmost hydrant / sprinkler.

The installation shall be complete with

necessary pressure gauge with gun metal shut

off cock on delivery side.

Pump shall be capable of furnishing not less

than 150% of rated capacity at a head of not

less than 65% of the rated head. The shut off -

head shall not exceed 120% of rated head.

Heat exchanger cooled (secondary cooling)

diesel engine of speed 1800 RPM suitable for

the above pump with automatic starting

mechanism and other accessories including

fuel tank (fabricated from 3mm MS sheet,

painted with two coats of synthetic enamel

paint over a coat of primer) of capacity

adequate to sustain pump operation for

c hours continuous working. The tank shall be

fitted with Magnetic oil level indicator, MH

with cover, drain valve, air vent including

structural supports (painted with approved

shade), 1 Nos. x 12 volt battery, heat

exchanger with necessary piping connections

& fittings, flexible coupling, coupling guard

& exhaust pipe connection complete as

Diseal engine tank 200 ltr capacity minimum. -

Common base plate for (a) and (b) from

e M.S. channel of required size. -

Including Diesel Engine control panel with

Battery charger. -

Suitable cement concrete foundation with

plaster, (design and drawing to be provided by

g the Contractor while the foundation will be

done by others) complete with antivibration

arrangement of cushy foot mountings.

Supply, installation, testing and

commissioning of jockey pump

(pressurisation pump) comprising of the 2,01,000.00

Horizontal end suction centrifugal pump of

180 LPM with 70 Head, suitable for operation

on 415 volts ± 6%, 3 phase, 50 HZ A.C

The installation shall be complete with

Flexible coupling and coupling guard,

complete as required.

The pump casing shall be CI, shaft shall be SS

& impeller / shaft sleeve / casing wearing ring

shall be bronze. The pump shall be provided

with mechanical seal The system shall be

complete with necessary pressure gauge with -

gun metal shut off cock on delivery side. (The

pump should meet the condition and shall be

gotten approved by the Local fire Authority).

Squirrel cage induction motor TEFC type for

operation on 415 V, 3 phase 50 HZ AC

supply for the above pump with a

synchronous speed of 2900 R.P.M. with -

flexible coupling and coupling guard etc. as

Common base plate for (a) and (b) from

M.S. channel as required size. -

Suitable cement concrete foundation with

plaster, (design and drawing to be provided by

e the Contractor while the foundation will be

done by others) complete with Antivibration

arrangement of cushy foot mounting.

Providing & fixing pressure switch assembly

with isolation valve suitable for working

pressure of 10 bar. Cost shall be inclusive of

providing any short pieces, nipples, elbows

etc as required.

General specification of pressure switch

Encloser : Painted Mild Steel to IP:33 as per

IS:13947 (Part-1)

Sensing Element Phosphor Bronze Bellows 3,700.00

Switching : 1 SPDT Contact System

Switch Rating : 6A Inductive / 10A Resistive

240V AC, 0.2A Inductive

Repeatability / Accuracy : ± 2% FSR

Process Connection 1/4" BSP (F)

Cable Entry : Suitable for 6 to 14 mm dia

Supplying, installing, testing and

commissioning of C.I. Non-return valves as

3.40 per IS:5312 (Part I) 1984, swing check type

with required flanges, nuts, bolts and gaskets

etc. complete. (PN 16 Rated.)

a 2 150 mm dia Nos.

b 1 100 mm dia Nos.

Providing & fixing of flange ended rubber

expansion bellow joint of standard length as

3.50 per manufacturers specs including rubber

gaskets, flanges, nuts, bolts and washers

complete as required. (PN 16 Rated.)

a 8 150 mm dia Nos.

Supplying, installing and commissioning of

CO2 4.5 Kg Fire Extinguisher containing

99.95% Co2 Gas, fitted with discharge hose,

wall mounting bracket etc., ISI approved as 3,900.00

per IS:15683:2006 complete with Required

size of Zebra paintaing on wall and floor.

Supplying, installing and commissioning of

ABC 6 Kg Fire Extinguisher containing MAP

50, Stored Pressure Type, fitted with Pressure

Gauge, fitted with discharge hose, wall

mounting bracket etc., applicable on Class A, 1,450.00

B,C ISI approved as per IS:15683:2006

complete with Required size of Zebra

paintaing on wall and floor.

PART -E (HVAC ITEMS)

Appendix-1- (VRF AC System with Standard VRF Units )

1 Section 1: High Side Work

Supply & Installation of Outdoor condensing

units of the following capacity with R

Gas Based Model. (Bidder to offer nearest

size of Unit & suitable combinations available

with them & must consider piping derating for

Up to 40 KWr capacity Min EER 3.28 and

40 to 70 KWr capacity Min EER 3.26 and

Above 70 KWr capacity Min EER 3.02 and

First Floor : CKT 01 - 32 HP ( 16 HP + 16 HP

)- - Top Discharge

Second Floor : CKT 01 - 20 HP ( 20 HP )- -

Second Floor : CKT 02 - 12 HP - Side

Second Floor : CKT 03 - 10 HP - Side

Third Floor : CKT 01 - 10 HP - Side

Third Floor : CKT 02 - 12 HP - Side

Supply & Installation of VRF-indoor units of

1.02 the following capacity. (Bidder to offer

nearest size of Unit available with them)

Ceiling mounted 4 way Compact Cassette

Unit with condensate drain pump

Ceiling mounted 4 way Cassette Unit with

condensate drain pump.

1.03 Remote control Systems

Cordless remote controllers ( Operating

Mode:- On/Off/Fan Speed/Mode/Temp )

Ref-net joints for above VRF systems.

1.05 1 Outdoor unit branch kit Nos. 5000

2 Section 2: Low Side Work

Epoxy painted M.S. structure for supports and

For VRF system, all refrigerant piping

between indoor & outdoor units duly insulated

as per specifications. All piping inside the

room shall be properly supported with hanger

and exposed piping shall be properly

2.02 supported in GI Perforated tray. Exposed

piping insulation to be covered with 1 layer

of glass cloth and 2 layers of UV paint and

all the insulation joints must be covered

with EPDM Rubber Tape. (minimum

mm thick Class O Insulation)

2.02.01 For Folloing HP Ref Piping

2.02.01.02 50 20 HP VRF Piping CKT

2.02.01.03 100 32 HP VRF Piping CKT

Supply & Installation of Insulated uPVC drain

piping for all VRF Indoor AC units. (All the

Insulation joint must be covered with

aerotape.) ( min 9 mm thick)

Testing & Commissioning of VRF system

along with topping-up of refrigerant Gas.

2.04.01 4 10 / 12 HP VRF CKT Nos

2.04.02 1 20 HP VRF Piping CKT Nos

2.04.03 1 32 HP VRF Piping CKT Nos

2.05 Electrcial Work:-

All Cu armored power cable between

electrical panel & VRF ODU’s located on

2.05.01 Terrace. This cabling should be properly

supported in G.I Cable trays where-ever

2.05.01.01 0 06 Sq mm X 4 Core Copper Rmt

2.05.01.02 0 10 Sq mm X 4 Core Copper Rmt

2.05.01.03 0 16 Sq mm X 4 Core Copper Rmt

10 Sq mm Cu Single core wire for earthing

All control cables between indoor and

2.05.03 outdoor unit lay in PVC pipe and clamped.(for

2.05.03.01 600 1.5 Sq.mm 2 core Shielded Control Cable Rmt

1.6 mm thk G.I perforated cable trays with

2.06 necessary structural supports, anchor bolts,

etc. for the above work.

90 Deg ODU Exhaust Air Cowl with 18 G GI

& MS Frame Work & Safety Chicken Mess

Appendix-2- (LVL 0 Room Split AC )

1 Section 1: High Side Work

SITC of DX air-cooled Split AC unit

complete with Indoor / Outdoor units along

with cordless remote controller & aditional

charge of refrigerant. (R-410a / R32

Refrigerant)(Min. 3 Star & Cu Cond.)

1.01 (Without Ref Piping )

2 Section 2: Low Side Work

Supply, Fabrication and Erecting structure

steel for support. Applying two coats of zinc

chromate primer of ICI, Asain make/eq. , with

rubber gasket between support & duct / pipe

2.01 as per specifications and drawings and as

directed by the Engineer-in-Charge client

/consultant. Make : Tata / Sail / JSW as per

IS-2062 with TC. ( with 2 coats of approved

0 color epoxy paint ) Kg 0

For AC system, all refrigerant piping between

IDU & outdoor units duly insulated as per

specifications. All piping inside the room shall

be properly supported with hanger and

exposed piping shall be properly supported

with clamp.Exposed piping insulation to be

covered with 1 layer of glass cloth and

layers of UV paint and all the insulation joints

must be covered with EPDM Rubber Tape.

For 1.0 / 1.5 TR ( Min 1/4" (0.8mm thk) &

2.02.01 6 1/2" (0.8mm thk) with min 13 mm thk Rmt

Isulation) 1000

Supply & Installation of Insulated uPVC drain

piping for all Indoor AC units. (All the

Insulation joint must be covered with

2.03.01 6 For 19/25 mm dia piping Rmt

All Cu armored power cable / control cable

between IDU to ODU’s .

2.04.01 8 4 Core x 2.5 Sqmm Copper armored) Rmt

2.04.02 0 6 Core x 2.5 Sqmm Copper armored) Rmt

2.05 1 L type Wall Mounted Powder coated GI Satnd Nos 1000

Signage Sticker for each OUD with Room

Name (for Identification) 400

2.06 2 Chipping Work in Wall Rmt 150

AHMEDABAD MUNICIPAL CORPORATION

ENGINEERING DEPARTMENT- BUILDING PROJECT

Name of Work:CONSTRUCTION OF COMMUNITY BUILDING

AT T. P. S. No. 5 (City Wall Improvement) (Section – 7) Final Sanc., F. P. No. 26, At: Dariyapur -

Kazipur, Taluka: City, District: Ahmedabad, near dariyapurgate dariyapur ward central zone,

FINANCIAL BID (Online Only)

RECAPULATION SHEET

SR.NO. DESCRIPTION AMOUNT

1 EARTH WORKS & ALLIED WORKS

2 CONCRETE & ALLIED WORK

3 STRUCTURAL STEEL & ALLIED WORKS

4 ROOFING & ALLIED WORKS

5 MASONARY AND PLASTER WORK

12 AS PER MARKET RATE

13 TOTAL ELCRTICAL WORK

14 VRF AC SYSTEM WITH STANDARD VRF UNITS AND SPLIT AC

15 A. FIRE HYDRANT SYSTEM

16 B. SPRINKLER SYSTEM

17 C.PUMP HOUSE EQUIPMENT

I/We am/are willing to carry out work at ______% above / below (should be written in figures and

the estimated cost mentioned above.

Estimated cost put to tender :Rs.00000 Estimated cost put to tender :Rs.000000

Add_____% above : Rs ___________ Deduct_____% below : Rs __________

In words : Rupees

Signature of contractor Additional City Engineer (Central Zone )

Seal Ahmedabad Municipal Corporation