CONSTRUCTION OF 200 BEDDED HOSTEL AT MAHARANA PRATAP SPORTS COLLEGE, RAIPUR DEHRADUN

Amount

DSR Item No.- 2.6.1 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 mm. All kinds of soil.

DSR Item No.- 2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

DSR Item No.- 2.35.3.1 Treatment of soil under existing floors using chemical emulsion@ one litre per hole, 300 mm apart including drilling 12mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

DSR Item No.- 2.27 Supplying and filling in plinth with Jamuna sand under floors, including watering, ramming, consolidating and dressing complete.

DSR Item No.- 4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

DSR Item No.- 4.10 Providing and laying damp-proof course 40 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size).

DSR Item No.- 4.17 Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth

DSR Item No.-5.1.2 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

DSR Item No.-5.2.2 Reinforced cement concrete work in beams, suspended floors, roof, walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

DSR Item No.-5.22.6 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-mechanically treated bars

DSR Item No.-5.9 Centring and shuttering including strutting,ropping etc. and removal of form for

DSR Item No.-5.9.1 Foundations, footings, bases of columns, etc. for mass concrete.

DSR Item No.-5.9.2 Centring and shuttering for Walls (any thickness) including attached pilasters,butteresses, plinth and string courses etc.

DSR Item No.-5.9.3 Suspended floors, roofs, landings, balconies and access platform.

DSR Item No.-5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts.

DSR Item No.-5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers.

DSR Item No.-5.9.4 Shelves

DSR Item No.-6.1.2 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

DSR Item No.-6.4.2 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1:6 (1 cement : 6 coarse sand)

DSR Item No.-6.13.2 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:4 (1 cement :4 coarse sand)

DSR Item No.-6.15 Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

DSR Item No.- 9.21.1 Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

DSR Item No.- 9.100.1 Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : 125 mm

DSR Item No.- 9.96 Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :

DSR Item No.- 9.96.1 300x16 mm

DSR Item No.- 9.96.2 250x16mm

DSR Item No.- 9.97.2 Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete

DSR Item No.- 9.97.2 250x10 mm

DSR Item No.- 9.97.4 150x10 mm

DSR Item No.- 9.100.1 Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : 125mm

DSR Item No.- 9.101.1 Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. completev Single rubber stopper.

DSR Item No.- 9.51.2 Providing and fixing fly proof galvanised M.S wire gauze to windows and clerestory windows using galvanised M.S. wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.63 mm. With 12 mm mild steel U beading.

DSR Item No.- 9.27.1 Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws :35 mm thick shutters with ISI marked M.S. pressed butt hinges bright finished of required size Second class teak wood

DSR Item No.- 10.14.1.1 Providing and fixing pressed steel door frames confirming to IS: 4351 manufactured from commercial mild steel sheet of 1.25 mm thickness including hinges jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25mm, or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechanical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge Profile B :Fixing with adjustable lugs with split end tail to each jamb

DSR Item No.- 10.14.1.1 Profile 'B' (Single Pattam)

DSR Item No.- 10.14.2.1 Profile 'C' (Double Pattam)

NSI Item- Providing and fixing Sliding NCL SECCOLOR or Equivalent make Series Window fabricated form roll formed sections made of Galvanized Steel Colour Coated / Powder Coated (Base Steel as per IS 513 "D" quality , Galvanized as per IS 277 with Zinc of 120 grams /Sqm. mrt.) with total coated thickness of 0.60 mm Coated Section should be with Primer Coat of Epoxy Primer of 5-7 micron thick, finish painted with Polyester paint of 12-16 micron thick and back coated with Alkyd backer of 5-7 micron or powder Coated with pure Polyester Powder up to 50-60 micron thick.Section for Frame should be of 72mmX 55mm, Section for Mullion should be of 72mm X50mm.Section for Shutter Frame should be of 47mm X 20mm , Section for Fixed Glass bead should be of 12mm X 12mm, and Section for Fly mesh should be of 40mm X20mm, and Section for Frame Glazed Shutter and Mesh Shutter should be cut to lenfth and mtr joined with Polypropylene Corner Brackets., Mullion Section should be joined with Frame /Mullion using Mullion Cap Ethyle Propylene Diamine Monomer (EPDM) Gasket should be used all around glass in shutter between Frame and Glazed Shutter and both sides of Fixed Glass . Rubber Gasket should be used around fly mesh to fix Mesh in Mesh Shutter . Each Glazed Shutter should be provided with MS Powder Coated Friction Hinges -1 set, High Grade Aluminium Powder Coated Handle -1 No.And 3" Aluminium Tower Bolt with Recivers -2 No. Glazed Shutter and Fixed Glass portions should be provided with a Stainless Steel 32 Gauge Fly mesh of 304 grades with 144 holes per sqm. Inch. Windows should be provided with Grill made of 10mm sqr. MS Bars welded to at 150mm center to center painted and fixed to window frame with screws. Window Frame should be fixed to brick /concrete masonary by using Nylon self expanding caps and driving MS electroplated 80mm long screw into the caps through frames.

DSR Item No.- 10.30.1 Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with: 5.5 mm thick glass panes

DSR Item No.- 10.25.2 Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

DSR Item No.- 10.25.1 Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In stringers, treads, landings etc. of stair cases including use of chequered plate wherever required, all completen stringers, treads, landings etc. of stair cases including use of chequered plate wherever required, all complete

DSR Item No.- 10.26.1 Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing and staircase railing including applying a priming coat of approved steel primer. M.S. tube

DSR Item No.- 10.28 Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

DSR Item No.- 11.41.2 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm

DSR Item No.- 11.46.2 Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm

DSR Item No.- 11.37 Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cement and matching pigment etc., complete.

DSR Item No.- 11.36 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

DSR Item No.- 8.12 Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigmen t of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge :

DSR Item No.- 13.1.1 12 mm thick cement plaster in 1:4 ( 1 cement and 4 fine sand) mortar including supply of all material , labour and T&P etc. required for proper completion of the work.

DSR Item No.- 13.1.2 12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand

DSR Item No.- 13.2.2 15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement: 6 fine sand

DSR Item No.- 13.80 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

DSR Item No.- 13.41.1 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water tinnable priming coat with cement primer

DSR Item No.- 13.47.1 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade : New work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

DSR Item No.- 13.62.1 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

DSR Item No.- 11.21.2.1 Providing and fixing 10 mm thick acid and/or alkali resistant tiles of approved make and colour using acid and/or alkali resisting mortar bedding, and joints filled with acid and/or alkali resisting cement as per IS : 4457, complete as per the direction of Engineer-in- Charge.In dado/skirting on 12 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand) Acid and alkali resistant tile

DSR Item No.- 22.14.1 Grading roof for water proofing treatment with Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

DSR Item No.- 14.90.1 Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer, 3 mm thick water proofing membrane, black finished reinforced with glass fibre matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufactured of density at 25°C, 0.87 - 0.89 kg/litre and viscocity 70 - 160 cps. Over the primer coat the layer of membrane shall be laid using butane torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 350/300 N/5 cm. Tear strength in longitudinal and transverse direction as 60/80N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane : 3 mm thick

DSR Item No.- 19.1.1 Providing, laying and jointing glazed stoneware pipes grade ‘A’ with stiff mixture

DSR Item No.- 12.41.2 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS :

DSR Item No.- 18.32.1 Constructing masonry chamber 30x30x50 cm, inside with 75 class designation brick work in cement mortar 1:4 (1cement :4 coarse sand ) with C.c 1:2:4 floor over C.C 1:5:10 Finished with a floating coat of neat cement complete .Rectangular shape 600x450mm internal dimensions

DSR Item No.- 19.2 Supplying and fixing C.I. cover 300x300 mm without frame for gully trap (standard pattern) the weight of cover to be not less than 4.5kg

DSR Item No.- 16.3.5 Supplying and stacking at site. Over burnt (Jhama) brick aggregate 90 mm to 45 mm

DSR Item No.- 18.10.1 Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. Iinternal work - Exposed on wall

DSR Item No.- 18.10.1 15 mm dia nominal bore

DSR Item No.- 18.10.2 20 mm dia nominal bore

DSR Item No.- 18.10.6 50 mm dia nominal bore

DSR Item No.- 18.12.6 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work.50 mm dia nominal bore

DSR Item No.- 18.46 Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :

DSR Item No.- 18.46.1 15 mm nominal bore

DSR Item No.- 18.46.2 20 mm nominal bore

DSR Item No.- 18.46.6 50 mm nominal bore

DSR Item No.- 18.49.1 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore approved quality

DSR Item No.- 18.51.1 Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. : 15 mm nominal bore approved quality

DSR Item No.- 18.52.1 Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore approved quality

DSR Item No.- 18.18 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :

DSR Item No.- 18.18.2 20 mm nominal bore

DSR Item No.- 18.18.3 25 mm nominal bore

DSR Item No.- 18.19 Providing and fixing gun metal non- return valve of approved quality (screwed end) :

DSR Item No.- 18.19.4.1 50 mm nominal bore (Horizontal)

DSR Item No.- 18.48 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. Circular tank

NSI Item- Supply and installation of Kirloskar make (2 HP) Single phase

DSR Item No.- 17.1.1 Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

DSR Item No.- 17.2.1 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

DSR Item No.- 17.7.1 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

DSR Item No.- 17.35 Providing and fixing soil , waste and vent pipes: S.C.I S&S pipe as per IS:1729

DSR Item No.- 17.35.1 100 mm dia

DSR Item No.- 17.35.2 75 mm dia

DSR Item No.- 18.65 Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth Nos. 102mm, height of 75mm with concealed fitting arrangements weighing not less than 106 gms.

DSR Item No.- 17.37 Providing and fixing M.S holder-bat clamps of approved design to PVC/Sand Cast iron/ cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc.

DSR Item No.- 17.37.1 For 100 mm dia pipe

DSR Item No.- 17.37.2 For 75 mm dia pipe

DSR Item No.- 17.38 Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete

DSR Item No.- 17.38.1 100 mm diameter pipe

DSR Item No.- 17.38.2 75 mm diameter pipe

DSR Item No.- 17.39 Providing and fixing plain bend of required degree wbolts and nuts complete

DSR Item No.- 17.39.1 100 mm diameter pipe

DSR Item No.- 17.39.2 75 mm diameter pipe

DSR Item No.- 17.60.1 Providing and fixing floor drain points formed out of 65 mm dia PVC ,elbow, including with 75mm dia Stainless Steel grating with frame, embedded in floor, all complete as directed.

DSR Item No.- 17.32.1 Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing

DSR Item No.- 17.56.1.1 Providing and fixing terminal guard 100 mm Sand cast iron S&S as per IS - 1729

DSR Item No.- 17.72 Providing and fixing PTMT towel ring trapezoidal shape 215mm long, 200mm Nos. wide with a minimum distances of 37mm from wall face with concealed fittings arrangement of approved quality and colours weighing not less than 80 gms

DSR Item No.- 17.57 Providing and fixing collar : Sand cast iron S&S as per IS - 1729

DSR Item No.- 17.57.1.1 100mm

DSR Item No.- 17.57.2.1 75 mm

DSR Item No.- 2.10.1.2 Excavating trenches of required width for pipes, cables, etc including excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.5 m including getting out the excavated soil and then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

DSR Item No.- 19.1.3 Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 200 mm diameter

DSR Item No.- 19.3.3 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design : 200 mm diameter S.W. pipe

DSR Item No.- 19.4 Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame o f 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:

DSR Item No.- 19.4.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

DSR Item No.- 19.7 Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :

DSR Item No.- 19.7.1 Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, totalweight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :

DSR Item No.- 19.8.1.1 Extra depth for manholes. Size 90x80 cm. With F.P.S brick class designation 75

DSR Item No.- 13.7.1 12 mm cement plaster finished with a floating coat of neat cement of mix

DSR Item No.- 11.3.1 Cement concrete flooring 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete. 40mm thick with 20mm nominal size stone aggregate.

DSR Item No.- 19.19.1 Man Hole Cover(Rectengular Shape) Size 600x450 mm)

DSR Item No.- 4.1.3 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

DSR Item No.- 6.23 Honey-comb brick work 10 / 11.4 cm thick with common burnt clay bricksof class designation 7.5 in super structure above plinth level upto floor V level with cement mortar 1:4 (1 cement : 4 coarse sand).

DSR Item No.- 16.3.5 Supplying and stacking at site. Over burnt (Jhama) brick aggregate 90 mm to 45 mm

DSR Item No.- 16.3.2 Supplying and stacking at site. Over burnt (Jhama) brick aggregate 63 mm to 45 mm size stone aggregate

DSR Item No.- 19.3.3 Supplying and stacking at site. Over burnt (Jhama) brick aggregate 53 mm to 22.4 mm size stone aggregate

DSR Item No.- 17.35.1.1 Providing and fixing soil, waste and vent pipes : 100 mm dia Sand cast iron S&S pipe as per IS: 1729

DSR Item No.- 17.56.1 Providing and fixing terminal guard :100 mm Sand cast iron S&S as per IS - 1729

DSR Item No.- 19.6.4 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 300 mm dia. R.C.C. pipe

DSR Item No.- 19.19.1.1 Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality 19.19.1 L D- 2.5 Rectangular shape 600x450 mm internal dimensions

SOR Item No. (1-4) Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6) upto plinth level with :

DSR Item No.- 13.47.1 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

DSR Item No.- 4.4.1 Providing and laying cement concrete in kerbs, steps and the like at or near ground level excluding the cost of centering, shuttering and finishing 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

SOR MISC (2-6) Providing and Laying of Interlocking Concrete Block Pavements of M-40 Grade having thickness 80 mm as per drawings and Technical Specification Clause 1504.

DSR Item No.- 2.31 Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared.

DSR Item No.- 16.1 Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity

DSR Item No.- 16.3.1 Supply and stacking at site (soiling) 90mm to 45mm size stone aggregate

DSR Item No.- 4.1.2 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:1.5:3 (1 Cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

ELECTRICAL WORK DSR Item No.- 1.10.2 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required.Group B

DSR Item No.- 1.11 WGSTLMIDTC Twin Control point wiring in PVC conduit, with modular type switch:Wiring for twin control light point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required.

DSR Item No.- 1.12 WGSTLPP2 Power plug wiring in PVC conduit (2x4 sq. mm) Wiring for light/power plug with 2x4 sq.mm FR PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 1 No 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.

DSR Item No.- 1.14 WGSTLSB Circuit/ submain wiring in PVC conduit:Wiring fir curcuit/ submain wiring alongwith earth wire the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.

DSR Item No.- 1.14.1 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

DSR Item No.- 1.14.2 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

DSR Item No.- 1.14.9 4 X 6 sq. mm + 2 X 6 sq. mm earth wire

DSR Item No.- 1.14.10 4 X 10 sq. mm + 2 X 6 sq. mm earth wire

DSR Item No.- 1.18.2 TLWGEC Telephone wiring in PVC conduit:Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.2 Pair

DSR Item No.- 1.21 PVCCON S/F PVC conduit:Supplying and fixing of following sizes of PVC conduit along with accessories in surface / recess including painting in case of surface conduit, or cuttting the wall and making good the same in case of recessed conduit as required.

DSR Item No.- 1.21.2 25 mm

DSR Item No.- 1.21.3 32 mm

DSR Item No.- 1.22.1 MB S/F metal boxes:Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc as required.75 mm X 75 mm X 60 mm deep

DSR Item No.- 1.24 PTSWEB S/F modular type switch/ socket:Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

DSR Item No.- 1.24.1 5/6 amps switch

DSR Item No.- 1.24.4 3 pin 5/6 amp socket outlet

DSR Item No.- 1.24.6 Telephone socket outlet

DSR Item No.- 1.25 MODFREB S/F modular type electronic fan regulator: Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

DSR Item No.- 1.31 LPACCPT S/F light plug point modular type accessories: Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings).

DSR Item No.- 1.32 PPACCPT S/F power plug point modular type accessories: Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

DSR Item No.- 1.33 CREB S/F ceilling rose:Supplying and fixing 3 pin, 5 amp. ceilling rose on the existing junction box/ wooden block including connection etc. as required

DSR Item No.- 1.34 BRHOLD S/F brass holder:Supplying and flxing brass batten/angle holder including connection etc. as required.

DSR Item No.- 1.41 ITCFFSUR ITC fluorescent fitting directly on surface: Installation, testing and commissioning of pre-wired, fluorescent fitting/ compact fluorescent fitting of all types, complete with all accessories and tube etc. directly on ceiling / wall, including connection with 1.5 sq.mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required.

DSR Item No.- 1.45 ITCCFFC ITC ceiling fan with cover on fan box: Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq, mm FR PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

DSR Item No.- 1.50.1 ITCEF450 ITC exhaust fan upto 450 mm sweep: Installation of exhaust fan upto 450 mm sweep in the existingopening, including making the hole to suit the size of the above fan, making good the damage, connection, testing, commissioning etc. as required.

DSR Item No.- 1.51 LOUSHEF Fixing louvers/shutters for exhaust fan: Extra for fixing louvers/shutters complete with frame for a exhaust fan of all sizes.

DSR Item No.- 2.4 PWTPMCBDB S/F TP MCB DB:Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

DSR Item No.- 2.4.3 8 way (4 + 24), Double door

DSR Item No.- 2.13 MCBTPIS S/F TP MCB isolator:Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissoning etc. as required. 63 amps

DSR Item No.- 2.10.1 MCBC S/F 'C' curve, SP MCB. Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

DSR Item No.- 4.1.4 Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 300 mm width X 50 mm depth X 1.6 mm thickness

DSR Item No.- 5.4 EARGIPL G.I earth plate elctrode:Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc.with charcoal/ coke and salt as required..

DSR Item No.- 5.9 EARG125X6 S/L 25 mm x 5 mm G.I. earth strip in ground:Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

NSI ITEM- Supply of AC 230/250 volts, 50 HZ energy efficient ceiling fan with standard down rod, blades, 3 nos. caps Model-Captiva 50 (1200 mm Sweep) etc. complete in all aspects as per direction of Engineer in Charge. 1200 mm sweep

NSI ITEM Supply of AC 230/250 volts, 50 HZ exhaust fans including providing nuts, bolts, mounting frame and other accessories etc. complete . Model- Ventil Air - DS 300 mm sweep 900 rpm ,complete in all aspects as per direction of Engineer in Charge. 300 mm sweep 900 rpm

NSI ITEM Supply and fixing of LED Tube light 1200mm 18W 865 T8 IP20 ,Lumen Output-1600 , 6500K ceiling mounted LED batten, extruded aluminium heat sink provided for efficient heat deissipation 7& integrated electronic driver. ( 1x18 W LED Double 6500K) complet in all aspects as per direction of Engineer in charge.

NSI ITEM SUPPLY OF LED Glass Bulb B22, 12 W ,6000k /4000k/3000K ,230/250 Volt,50 HZ ETC, complete in all aspects as per direction of Engineer in Charge.

NSI ITEM Supply & fixing of main panel with 250 amp. incoming with 9 Nos. 25 amp. four pole MCB as outgoing ameter, Voltmeter

NSI Item- Supply and installation ,Testing and Commissioning of TISUN make 1500 LPD(500LPD X 3 Nos. tank) with 12 Flat plate Collectors , Premium Closed Loop SS 304 Tank with HeatExchanger, Circulation Pump, Control Panel, Temperature Pressure, Relief Valves with electrical back up of 6 Kwatt X 3. Complete With prefabricated MS hot dipped galvanized and painted mounting structure. Max. system operating Pressure- 1kg/cm² ,Max Water Temp. 90º C. complete in all aspects as per directions of engineer- in-charge

NSI ITEM Supply and fixing of LED Post-top 27 W ,IP Rating-IP65, Lumen Output (lm)-2500 (4000K), 2300 (3000K), System Efficacy (lm/W)-85 complete in all aspects as per direction of Engineer in charge.

NSI Item- Supply,of following sizes of PVC sheathed LT XLPE armoured, aluminium 1.1KV grade, as required of the following sizes.

NSI ITEM 3.5c x50 sq.mm cable

NSI ITEM 4c x10 sq.mm cable

NSI ITEM Supply and fixing of floor panel with 125 amp incoming with 4 nos. 32amp MCB outgoing with suitable size busbar.

NSI ITEM Supply and installation of 15 Ltr. Gyser (water Heater).

VKJ Projects Pvt. Ltd.

Makin Developers Pvt. Ltd.

M/S Shiv Kumar Agarwal

Sunehari Bagh Builders Pvt. Ltd.

M/s Mahalaxmi Construction

M/s Sameer Construction Co.

COX INFRATECH PVT LTD