ENGINEERING, PROCUREMENT AND CONSTRUCTION (EPC) FOR DEMOLITION AND RECONSTRUCTION OF CERTAIN OFFICERS MARRIED ACCOMMODATION (72 DUs) AT DOLPHIN HILL UNDER GE(P) NO.2 (N) VISAKHAPATNAM

Amount

Notes : 1. The schedule"A" Part -I is not pre-priced by MES and the pre-priced rate indicated as "Rs 0.00" under Col. 5 siginifies this fact only. 2.Schedule "A" Part – II to Part – XI are prepriced by MES. Bidders shall insert their Lumpsum amount in Green coloured field under Column - 6 only

Engineering, Procurement and Construction (EPC) of OFFICERS MARRIED ACCOMMODATION (72 DUs) with G+2 configuration (i.e., in 12 blocks with 06 DUs in each block) INCLUDING INTERNAL WATER SUPPLY AND INTERNAL ELECTRIFICATION complete, all as specified and directed.

Engineering, Procurement and Construction (EPC) of sewage sump of capacity 40000 Ltrs, complete, all as specified and directed.

Engineering, Procurement and Construction (EPC) of sewage sump cum pump house of capacity 20000 Ltrs complete all as specified and directed. (Note : Pump will be measured and paid separately under relevent item of BOQ)

Lumpsum price worked out by the contractor for "EARTH WORK EXCAVATION AND AREA DEVELOPMENT", as listed in SCHEDULE "A" PART – II.

Lumpsum price worked out by the contractor for "ROAD, HARDSTANDING AND CULVERT", as listed in SCHEDULE "A" PART – III"

Lumpsum price worked out by the contractor for "AREA DRAINAGE" as listed in SCHEDULE "A" PART – IV "

Lumpsum price worked out by the contractor for "RAIN WATER HARVESTING" as listed in SCHEDULE "A" PART – V".

Lumpsum price worked out by the contractor for "RETAINING WALL ", as listed in SCHEDULE "A" PART – VI".

Lumpsum price worked out by the contractor for "COMPOUND WALL ", as listed in SCHEDULE "A" PART – VII".

Lumpsum price worked out by the contractor for "SEWAGE DISPOSAL" as listed in SCHEDULE "A" PART – VIII".

Lumpsum price worked out by the contractor for "EXTERNAL ELECTRIFICATION" as listed in SCHEDULE "A" PART – IX"

Lumpsum price worked out by the contractor for "EXTERNAL WATER SUPPLY" as listed in SCHEDULE "A" PART – X ".

Lumpsum price worked out by the contractor for "DISMANTLING/ DEMOLITION", as listed in SCHEDULE "A" PART – XI ".

[Miscellaneous Items SCHEDULE "A" PART – XII] [ROADS /PATH/HARD STANDING/ CULVERT, ARBORICULTURE, EXTERNAL ELECTRIFICATION, SOLAR POWER INVETER , PVC CONDUIT, HOT WATER SUPPLY, SOLAR WATER HEATER, SEWAGE DISPOSAL E/M, EXTERNAL WATER SUPPLY, & FURNITURE ]

ROADS /PATH/HARD STANDING/ CULVERT

Granular sub Base (GSB) with grading V of 150mm thick Compacted thickness (laid in two layers of 75mm each, Compacted seperately) confirming to grading as specified, spread, rolled and consolidated to required gradient asnd camber complete using necessary mechanical paver/ Grader and vibratory soil compacter of Capacity 8-10 ton all as specified and as directed. (a) Pavement shall be made for solid quantity arrived after consolidation. (b) Compaction of granual sub base filling shall be carried out under Optimum moisture condition to achieve 98.50 modified density. (c) Curing shall be carried out as per IRC recommendations. (d) Before execution of this item the approved material obtained from outside MD land shall be tested/ checked for suitability to use.

(e) The lead/ Royalty involved is to be ascertained by the contractor before quoting his tender and no extra payment/ Adjustment for increased in lead or Rate of Royalty due to whatever reason shall be admissible on his account. (f) Contractor shall use Vibratory earth compactor inlieu of Power roller to achieve 98.00% MDD at OMC without any extra cost and the method of compaction to be adopted as per recommendation of agency reporting MDD at OMC. (g) GSB shall be as per MORTH specification as detailed in Perticular specification.

Wet mix Mecadam of 250mm thick (Compacted thickness) laid in three layers compacted seperately with Coarse aggregate of specified grade spred rolled and consolidated to required gradient and camber complete using mechanical paver/ Grader and Pandom Vibrator of capacity of minimum 8-10 Tons at OMC to achieve atleast 98% MDD determained using modified Proctor density determination method as per IS code on prepared GSB surface complete all as specified and as directed. Note : 1. The rate quoted shall be for 250mm compacted thickness. 2. Each layer shall be rolled seperately.

Material and Labour for Painting lines, dashes, arrows, letters, etc. on road surface with hot applied retro reflective thermoplastic paint confirming to MORTH (Clause. 803.40) all as specified with 8% glass beads using special applicator machine with heating arrangement upto 160 Degress C, including cleaning and drying the road surfaces to ensure dust,oil,grease and moisture free surface beforeapplying paint complete all as specified as directed.

ARBORICULTURE

Supply & Planting carpet Grass grass by piece turfing including preparation of ground upto 30 cm deep and filling soft soil, cow dung and watering etc complete all as specified and directed. Note: Loose soil and cow dung shall be measured and paid separately UNDER SUPPLY ONLY.

Supply only approved loose soil of best quality for plantation.

Supply only approved manure (Cow dung) of best quality for plantation.

Supply only approved vermi compost of best quality.

Supply and plantation of Mango Plant (height of plant not less than 2.0m above ground level) incl preparation of ground up to 30cm deep and filling of good earth, cow dung vermi compost and watering etc complete all as directed by the Engineer-in-charge.

Supply and plantation of Guava Plant (height of plant not less than1.50m above ground level) incl preparation of ground up to 30cm deep and filling of good earth, cow dung vermi compost and watering etc complete all as directed by the Engineer-in-charge.

Supply and plantation of Naseberry tree of height not less than 1.50 m above ground level) incl preparation of ground up to 560cm deep and filling of good earth, cow dung vermi compost and watering etc complete all as directed by the Engineer-in-charge.

Supply and laying 25mm bore GI Tubing medium grade conforming to IS :1239 with all fittings laid in trenches complete all as specified and as directed

Supply and laying 15mm bore GI Tubing medium grade conforming to IS :1239 with all fittings laid in trenches complete all as specified and as directed

Supply, fix & testing of 25mm dia Gun metal gate valve with iron whell head screwed both ends for in iron pipe compelte all as specified and as directed

Supply, fix & testing of 15mm dia Gun metal gate valve with iron whell head screwed both ends for in iron pipe compelte all as specified and as directed

S & F for brass water Sprinckler 15 mm dia OL hose--end sprayer fixed in pipe line, consisting of 02 Rotary Nozzles/ Radiators, radius 0.5-5.5M, flow 0.2 to 17 LPM, pop-up height 2M and weight not less than 0.4Kg complete all as specified.

MAINTENANCE OF ARBORICULTURE

MAINTENANCE OF ARBORICULTURE WORKS DURING DEFECT LIABILITY PERIOD OF WORK. Material and labour for maintenance including watering and fertilization of all the grass/plants/trees by weeding housing saucer melding once in every 15 days, planting new plants/grass spices and height with out any extra cost to the department for period of maintenance period of TWO YEARS from the completion date of project complete all as specified and directed.

EXTERNAL ELECTRIFICATION

Supply and erect two pole structure on with SP-410-55, 11 meter steel Tubular pole with necessary spaces, for mounting of HT air break switch and DO fuse units complete with including all excavation and concrete (1:24) type B1 filling in foundation and base, painting, Steel bracing, clamps, channels, insulators, anti-climbing device etc. complete all as specified and as directed.

XLPE insulated and screened insulated, FRLS armoured and PVC bedded underground HT cable, ISI marked with aluminium stranded conductor 11000 Volt grade (heavy duty) of size 3 Core, 120 Sq.mm cross section conforming to IS-7098 (Part-II) laid in trenches, fixed to walls or passing through pipes and connecting up complete all as specified and directed.

Supply, installation, testing and commissioning of 11 kV outdoor Compact Sub Station in compliance with IEC 62271-202 with Transformer 630 KVA 11 kV/433 V DYn11 conforming to IS 2026 & IS1180( latest amendments), oil filled ONAN type, energy efficiency Level-2,copper wound with off circuit tap links of range +/- 7.5% in steps of 2.5 % ,class of insulation -F, temp. rise over ambient temp of max. 50 degree C, losses & % impedance as per ECBC 2017, insulation class F including HT and LT switch gears, the enclosure having IP 54 degree of protection for HT and LT switch gear compartment and IP 23 degree of protection for transformer compartment shall be minimum of 1.5 thick powder coated/ wet polyurethane painted GI sheet mounted on hot galvanised 4 mm thick GI base frame and with partially modular design of GI sheets fastened by riveting .,the partition between compartment shall be min 1.5 mm thick ,rated temperature class for transformer compartment shall be k10 & lowers shall be designed for natural ventilation and with thermal class K20, roof should be designed to support min load of 250 kg/sqm, gaskets/stiffeners shall be provided as required, proper interlocking arrangement for safety of operator and to avoid corrosion door should have stainless hinges, the whole structure shall be fitted with lifting beams/ hooks for easy installation at site :

HT Switch gears : 11 kV, 630 Amp, 21kA/1sec, non-extensible RMU in min 2.5 mm thick stainless non ferrite and non-magnetic robotically welded steel tank with copper bus bar, compact switch gear consisting of one no. fixed manual VCB with direct incoming connection in SF6 insulated sealed for life gas tank with IP67 degree of protection with integrated current protection, LT Switch gears : Incomer- 415 V, 1000A, 50 kA EDO type ACB with microprocessors based release of over-current, and earth fault protection including copper bus bar Outgoing- 415 V, 250 A, 36kA (05 Nos), including APFC panel with microprocessor relay with 6 stage, MDXL capacitor of steps 25KVAR x 6 Nos (150KVAR) complete all as specified and as directed.

Supply, laying and testing cable XLPE insulated and PVC sheathed, FRLS armoured heavy duty underground cable, ISI marked with aluminium stranded conductor 1100 Volt grade of size 3½ Core, 240 Sq.mm cross section suitable for earthed system, laying in trenches / duct / fixed to poles / drawn through pipes / sleeving through pipe in duct, including suitable size Double compression copper stainless steel cable gland, crimping type cable lugs, sockets etc complete all as specified and directed. .(from CSS to FP 1,2,3&4)

Supply, laying and testing cable XLPE insulated and PVC sheathed, FRLS armoured heavy duty underground cable, ISI marked with aluminium stranded conductor 1100 Volt grade of size 3½ Core, 70 Sq.mm cross section suitable for earthed system, laying in trenches / duct / fixed to poles / drawn through pipes / sleeving through pipe in duct, including suitable size Double compression copper stainless steel cable gland, crimping type cable lugs, sockets etc complete all as specified and directed. . (From FP 1,2,3,& 4 to Each blocks)

Supply, laying and testing cable XLPE insulated and PVC sheathed, FRLS armoured heavy duty underground cable, ISI marked with aluminium stranded conductor 1100 Volt grade of size 4 Core, 16 Sq.mm cross section suitable for earthed system, laying in trenches / duct / fixed to poles / drawn through pipes / sleeving through pipe in duct, including suitable size Double compression copper stainless steel cable gland, crimping type cable lugs, sockets etc complete all as specified and directed. .

Supply, install, test and commissioning of LT Panel board (Distribution Panel) made out of CRCA sheet , 3.15 mm thick outdoor Pedestal type, CPRI approved, totally enclosed with front and rear opening, hinged doors with projected an raised platform of suitable size weather and water proof with necessary locking arrangements along with lugs, cable glands of various sizes for cables, danger notice plate, strickering of Switcher gear about termination of switch gear, cable connector for connecting multi cables located in cable chamber terminated form the switchgear, and the nuts/ bolts etc used are to be made of rust proof material incl as per IS: 8623 aluminium bus bar with insulators suitable for three phase and four wire LT AC, 50 Hz 415 V, 400 A capacity complete with powder coating, necessary internal electric connection as required, with and inclusive of the following items: Incoming : a) MCCB 4 Pole, 415 V, Adjustable type, 250 Amps with breaking capacity 36 kA- 01 No Outgoing : a) MCCB 4 Pole, 415 V, Adjustable type, 100 Amps with breaking capacity 16 kA- 03 Nos b) MCB TPN 32 A -02 Nos c) Intelligent Panel meter to measure voltage, current, frequency, power factor, KWH, etc with all connected CTs - 01 No d) LED indicating lamps with colour Red, Yellow, Blue - 01 Set

Earthing complete with Galvanised iron earth plate electrode 600 X 600 X 6 mm thick burried directly in ground [earth pit not less than 2.25 m deep below ground level] with top edge of plate not less than 1.50 m below normal ground level connected to 32 X 6 mm GI earth strip [Earth Lead] and GI pipe 50 mm, Medium Grade for earthing lead protection to the extent of maximum 7.5m in length from earth plate, Earth Plate Electrode surrounded by 150 mm thick packed layers of Charcoal and Rock Salt filled in alternate layers, connected to the plate by means of brass Bolts & Nuts complete all as per Electrical plate No. 3 of SSR Part - I, connected to panel / DB including testing on completion including main earthing, Charcoal, Rock Salt, PCC chamber [1:3:6, Type C1] with RCC cover of 1:2:4 type B1 , MS Funnel with 20 mm bore, medium grade GI Watering pipe, wire mesh, earth work excavation, return filling, removal of surplus soil etc. complete all as specified. (Earthing of for Sewage & EE)

M & L for earthing complete with galvanised steel earth plate electrode 60cm×60cm× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0 mm dia by meams of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown electrical plate No.3, connected to earthing test point all as specified and directed and testing on completion.

Loop in loop out box (minimum size-200mm x 160mm x 98mm)of FRP made with IP 65 protection of thermoplasic circuit breaker boxes with metric knockouts for cable entry and exit, Combi climate Cable Glands of IP 66/ IP 67 for cable entry and Grommets IP 65 for conduit for cable exit with MCB 6 Amps, 10 kA, C Curve Overload and Short Circuit protection, terminals as bus terminals for cable with necessary fixing arrangemets and with cable glands, etc all as specified and directed.

M & L for PVC insulated copper conductor of size 2.5 sqmm 3 core drawn through PVC pipe with clamping materials complete all as specified and as directed.

Supply and fix Cone LED Bollard, 8 Watt, 230 V, AC, outdoor type luminaire with diffuser at the upper portion with IP 65 protection complete all as specified and as directed.

SOLAR POWER INVETER

Supply, install, testing and commissioning of solar panel powered inverter (sine wave) with battery back up for 08 hours capacity 01 KW (Single phase 230 Volts, 50 Hz, AC supply) complete (off grid type) with and inclusive of all electrical and mechanical accessories & stand for inverter and batteries complete all as specified and as directed. (for four blocks one number) Note :- [i] Solar panel of Specification 320 Wp (Minimum) polycrystalline type to be provided [ii] Inverter and battery backup shall be near the building staircase. [iii] Tubular battery of 12 Volts, 150 AH of sufficient quantity to be provided and rate quoted shall be deemed included in the cost of batteries. [iv] Manual changeover switch 20 Amps single phase, 240 Volts to be provided near inverter for switching on to normal electric supply, incase solar system fails. Cost of the same deemed to be included in the rate quoted. [v] Solar inverter supply will feed to light fittings of parking area, staircase lights, building security lights in ground floor and passage lights, staircase lights of each floor of building. [vi] Before commencement of work contractor shall submit complete wiring diagram for approval of Eng-in-Charge.

Supply and lay XLPE insulated and PVC sheathed, FRLS armoured heavy duty cable, ISI marked with aluminium stranded conductor 1100 Volt grade of size 2 Core, 6 Sq.mm cross section suitable for earthed system, laying in trenches / duct / fixed to poles / drawn through pipes / sleeving through pipe in duct, including suitable size Double compression copper stainless steel cable gland, crimping type cable lugs, sockets etc complete all as specified and directed.

PVC CONDUIT

Supply and fix Rigid non-metallic PVC conduit of 25 mm dia exclusive of boxes (junction/termination) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc including GI wire for wiring of TV/ telephone cable concealed in wall or clamped on wall all as specified and directed.

Supply and fix Rigid non-metallic PVC conduit of 40 mm dia exclusive of boxes (junction/termination) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc including GI wire for wiring of TV/ telephone cable concealed in wall or clamped on wall all as specified and directed.

Supply and fix telephone sockets(Jack type) RJ 11-1 with shutter 1 module complete with all accessories all as directed

Supply and fix TV co-axial socket 1 module complete with all accessories all as directed.

HOT WATER SUPPLY

Supply, install, testing and commissioning of storage water heater/geyser 25 Ltrs capacity complete with inlet and outlet pipe with all standard fittings and fixing accessories for fixing to wall including making electrical & water line connections and necessary civil work and complying with the following specification:- (i) Type:- Vertical (ii) capacity of Inner tank:- 25 Ltrs (iii) Colour:- White (iv) Temperature sensitive LED indicator (v) Feather touch digital temp control (vi) Shock proof 3 pin plug. (vii) Upto 8 bar pressure resistance inner tank (viii) Multifunctional safety valve. (ix) IPX4 technology to protect electrical parts from water splash. (x) Earth leakage current breaker to cut off power immediately in case of current leakage and protect user from electric shocks. (xi) Tank: Made with ultra-thick super cold rolled steel plates dry powder coating finish and energy saving high density PUF insulation. (xii) Heating element:- Glass coated heating element with resistant to oxidation and carbonation at high temperature of capacity 2000 W capacity.

(xiii) Heavy duty magnesium anode rod with steel core to protect enamelled tank from rust and corrosion 230 V, single phase, 50 Hz AC power supply 5 star energy saving rating with BEE level.

SOLAR WATER HEATER

Supply, install, testing and commissioning of Solar water heating system, Flat plate collector type based on indirect transfer of heat of 200 litre per day capacity, with electrical heating back up all as specified and as directed. ( 1 No. per each block of 6 Nos Qtrs for 01 toilet & Kitchen each)

SEWAGE DISPOSAL E/M

Material and Laboure for laying of Ductile pipe with spigot and socket end centrifugally cast(spun) class K-9 of 100 mm (4") dia pipe conforming to IS-8329 including provision of specials, such as tees, elbows,bends reducers, taper pieces, including testing and commissioning all as specified and as directed.

Supply, installation, testing and commissioning of non-clog type vertical sewage disposal submersible pump 600 LPM, 22 m head, 3.7 kW/5.0 HP, 415 V, 3 phase 50 cycles with chrome steel impeller , including supply, installation with guide rail and lifting chain, cables, suitable to handle sewage water including silt, sand etc. complete all as specified and as directed.

Supply and fixing electric submersible copper cable of size 6.0 sqmm, 3.0 core 415 V, and complete all as specified and as directed.

Supply, installation, testing and commissioning of star delta type starter panel with steel enclosure for submersible pump, 415 V, 5 HP capacity all as specified and as directed

EXTERNAL WATER SUPPLY

Supply and lay pipe ductile Iron, Class “K-9” ,150 mm (6”) dia centrifugally cast with socket and spigot ends conforming to IS-8329 in standard length suitable for push on rubber gasket tyton joints complete all as specified and as directed.

M & L for Masonary valve chamber for 900 x 900 x 900 mm (internal dimensions) suitable for 150 mm bore sluice valve including excavation and earth work in any type of soil and 100 mm thick PCC 1:4:8 type D2 using 40 mm graded stone aggregate foundation, brick work in CM (1:6) plastering internal surface 15 mm tick in CM (1:4) PCC (1:3:6) type C1 coping 50 x50x6 mm angle iron 6 mm thick MS plate cover complete with locking arrangement painting steel and iron surface with two coat of synthetic enamel paint over a coat of zinc chrome primer all as shown on drawing and as specified.

M & L for valve chamber of internal size 750 x 750 x 750mm comprising of 50mm thick PCC 1:5:10 type E2 foundation, 200mm thick brick wall in CM 1:6, 15mm thick plastering in CM 1:4 internally and externally up to 50mm be;ow GL,100mm thick PCC 1:3:6 type B1 as in copings,3mm thick MS sheet cover with suitable hinges and locking arrangement, painting steel surfaces with two coats of synthetic enamel paint over a coat of primerincluding necessary earth work and excavation in any type of soil complete all as directed.

M & L for Boring of holes under road, pavement, hard standing by trenchless technology using ultra sound technique and necessary machine including HDPE pipe of 150 mm dia suitable for 0.4 mpa working pressure complete all as specified and directed.

FURNITURE

Almirah Medium steel all as per FD-1032

Almirah large steel half hanging all as per FD/E6/MAP/18

Bath mat (PVC) all as per FD/E6/MAP/07

Bed hard all as per FD/E6/MAP/08 (R)

Bin Linen multi purpose all as per FD/E6/MAP/09

Chair dining officers all as per FD/MAP-II/04

Chair verandah all as per FD/E-6/MAP/11

Chair writing all as per FD/E-6/MAP/ 12

Chair computer all as per FD/E-6/MAP/ 01

Chapoy folding IP with hardtop all as per FD- 388(R)

Chapoy IP folding all as per FD/MAP-II/01

Mirror dressing (Gents) all as per FD/E-6/MAP/ 16

Hat Stand with mirror all as per FD- 1110

Ladder Aluminium all as per FD-1025

Table peg all as per FD-384

Plate rack all as per FD-97(M)

Reseptacle PVC all as per FD/E-6/MAP/ 13

Rack shoe steel all as per FD/E-6/MAP/ 02 (R)

Side board all as per FD-1112

Sofa set 5(3+1+1) seater cushioned all as per FD/MAP-II/02

Stool dressing with cushioned seat all as per FD/E-6/MAP/ 14

Table bed side all as per FD/E-6/MAP/ 15 (R)

Table centre all as per FD/E-6/MAP/ 08

Table dining 6 Persons all as per FD/MAP-II/03

Table dressing Ladies including stool all as per FD/MAP-II/07

Table writing all as per FD-275

Table computer all as per FD/E-6/MAP/ 03

Teapoy all as per FD-208

Teapoy Verandah all as per FD/E-6/MAP/ 17

Trolly for TV all as per FD/E-6/MAP/ 04 (R)

Aalaya Engineering Project Private Limited

CHHABINDRA KUMAR PRADHAN

RAGHUSONS INFRA ENGINEERING PVT. LTD

SHRADHA SABOORI PROJECTS (INDIA) PVT LTD

DES RAJ AND SONS BUILDERS PVT LTD

SOOD ASSOCIATES PVT LTD

CH.VEERARAGHAVULU CONSTRUCTION PVT LTD

RKEC Projects Limited

Som Projects Pvt Ltd