PROVN OF BEARER ROOM, TILING OF BAR LIBRARY, BILLIARDS ROOM OF OFFRS MESS AND ADDN/ALTN OF BLDG NO 39 INFRONT OF LAO OFFICE NHQ PROVN OF EXHAUST FANS IN BATHROOM AT VOHRA, SUNDER RAO BLOCK AND GYAN VIHAR AT OUTRAM LINE UNDER GE (ARMY) BARODA

Amount

Surface excavation n.exc (not exceeding) 30cm deep and averaging 15cm deep and getting out in soft/loose soil

Excavation in trenches n exc 1.5m wide and n exc 1.5m in depth for foundation, etc or for the shafts, well, cesspits, manholes, pier holes, etc n exc 10 Sq m on plan and n exc 1.5m in depth and getting out in soft/loose soil.

M & L Cement concrete in foundations, filling and mass-concrete type D2 1:4:8 (40 mm graded stone aggregate) all as specified and as directed.

M & L for M-25 Grade nominal mix reinforced cement concrete in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under-reamed piles and mass concrete all as specified and as directed.

M & L for M-25 Grade nominal mix reinforced cement concrete in column, pier, pillars beams; plinth beams; bases for columns, etc; basement slabs, under-reamed piles and mass concrete all as specified and as directed.

M & L for M-25 Grade nominal mix reinforced cement concrete in lintel, lintel beams; plinth beams; bases for columns, etc; basement slabs, under-reamed piles and mass concrete all as specified and as directed..

M & L for M-25 Grade nominal mix reinforced cement concrete in slab supported on wall, shelves slab dick slab, bases for columns, etc; basement slabs, under-reamed piles and mass concrete all as specified and as directed..

Use and waste formwork for rough finished flat surface of concrete to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter.

Use and waste formwork for rough finished flat surface of concrete sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc.

Use and waste formwork for rough finished flat surface of concrete to sides of concrete to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping).

M&L for Brickwork with sub class ‘B’ bricks straight or curved on plan exc 6 m mean radius built in CM 1:6 all as specified and directed.

M&L 40 mm thick Damp proof course in cement concrete type Bo 1:2:4 to horizontal or vertical surfaces including necessary formwork using water proofing compound @ 3% by wt of cement.(WPC will be measured separately)

Applying evenly a coat of blown type bitumen at the rate of 1.50 kg per square metre and blinding with clean dry sand @ 0.05 cu. m. per sq. m

M & L for mild steel TMT bars 10mm dia and over, cut tolength, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

M & L for mild steel TMT bars but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/loose soil

Spreading and leveling of soft/loose soil in floor in layers n exc. 25 cm thick including well ramming watering as required.

Removing excavated soil n exc 50 m and deposited where directed at a level n. exc 1.5 m above the starting point

M&L Hardcore of broken stone of gauge n exc. 63 mm, deposited, spread and leveled in layers n exc. 15 cm thick, watered and rammed to a true sur-face

M&L cement concrete 75 mm thick, type D2 1:4:8 (40 mm graded stone aggregate) in sub base of flooring.

M&L 25 mm thick cement concrete in flooring type Bo, 1:2:4 (12.5mm graded aggregate) all as specified and as directed.

M&L for non skid colour ceramic tile 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc set and jointed inneat cement slurry and pointed in white or colour cement to match including screed bed or bedding layer of 15 mm thick, in CM 1:6 (Tile pattern and decoration may be as directed by Engineer-in-charge)

M&L for Glazed ceramic coloured walls tiles in vertical surfaces 300x200x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick rendering on vertical surface of wall or concrete surfaces in CM 1:4 to receive wall tiles (Tile pattern and decoration may be as directed by Engineer-in-charge).

M&L 75 mm thick cement concrete type C2 1:3:6 using 40mm graded stone aggregate in plinth protection for finished even and smooth without using extra cement including forming joints and filling with bituminous filler material.

M&L Rendering in two layer on fair faces of brick work or concrete surfaces of wall 5 mm thick in CM 1:4 mixed with WPC @ 3% by wt of cement for finished even and smooth without using extra cement over 10 mm thick rendering in cement mortar 1:6 smooth without using extra cement (WPC will be measured separately)

Rendering 10 mm thick on fair faces of brick work or concrete surfaces of wall in cement mortar 1:6 for finished even and smooth (without using extra cement)

Rendering 10 mm thick on fair faces of brick work or concrete surfaces of wall as backing coat in cement mortar 1:6 for finished even and fair (without using extra cement)

Rendering 5 mm thick on fair faces of ceiling in cement mortar 1:3 for finished even and smooth withou using extra cement complete all as specified and as directed.

Supply only integral water proofing compound

S & F for Towel rail 600 mm long of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats.

S & F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification and drawing. The door frame shall be tied to the wall using 75/100mm long MS screw as directed .

S & F Factory made solid panel PVC door shutte 30mm thick (style) consisting of frame made out of MS tube for top and bottom rails. M S tube for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stile and rails with suitable PVC sheet beading and jointed together with solvent cement.

S&F Butt hinge, medium wight, cold rolled mild steel of 100 mm size

S&F 150 mm aluminium alloy handles, cast type anodised all as specified.

S&F150mm aluminium anodised barrel tower bolts of extruded section and fixed.

S&F 3.00mm thick figured glass, pin head type and glazing with oil putty in square n exec 0.5 sqm in each pane

M&L preparing new plastered surfaces of wall and applying three coats of white wash on wall complete all as specified and as directed.

M&L preparing new plastered surfaces of ceiling and applying three coat of white wash complete all as specified and as directed.

M&L preparing new plastered surfaces of wall and applying two coats of cement base paint over a coat of primer.

M & L for 10 mm thick cement plaster (1:3) in CM with using water proofing compound @ 3% by weight of cement as per manufacturer's instructions shall be applied on padding concrete when concrete is still green complete all as specified and directed by Engr-in-charge. (WPC will be measured separately).

M & L for applying evenly a priming/tack coat with bituminous primer at 10 kg per 10 sq metre (Paving bitumin).

M & L for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified.

Demolition of stone slab/tiles of any description or thickness in floor, wall, aprons etc. Laid bedded and pointed in any mortor (without taking off backing coat) complete.

M&L for non skid colour ceramic tile 7 to 8 mm thick area of each tile exceeding exceeding 0.11 sqm but not exceeding 0.18sqm , in floors etc set over including screed bed or bedding layer of mortar 15 mm thick for laying floor finishes with CM 1:6 (Tile pattern and decoration may be as directed by Engineer-in-charge)

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc.

M & L preparing new plastered surfaces of wall and applying two coats cement base paint over a coat of primer on external wall.

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 all as specified and directed.

M&L for non skid colour ceramic tile 7 to 8 mm thick area of each tile joint free exceeding 0.18 Sqm but not exceeding 0.38 Sqm , as in floors etc set over and including high performence adhisive manufactured by somani ezifix tile adhisive or equivalent mixed in cement as per manufacturer instruction and jointed with polymer modified cementetious grout manufactured by somani ezy grout or equivalnet of pigment matching to tile color including screed bed or bedding layer of mortar 15 mm thick for laying floor finishes with CM 1:6 (Tile pattern and decoration may be as suggested by Engineer-in-charge)

M&L for non skid colour ceramic tile 7 to 8 mm thick area of each tile joint free exceeding 0.18 Sqm but not exceeding 0.38 Sqm , as in skirting etc set over and including high performence adhisive manufactured by somani ezifix tile adhisive or equivalent mixed in cement as per manufacturer instruction and jointed with polymer modified cementetious grout manufactured by somani ezy grout or equivalnet of pigment matching to tile color including rendering or backing layer of mortar 10 mm thick for fixing tiles with CM 1:4 (Tile pattern and decoration may be as suggested by Engineer-in-charge)

Rendering 10 mm thick on fair faces of brick work or concrete surfaces of wall in cement mortar 1:6 for finished even and smooth (without using extra cement)

Rendering 10 mm thick on fair faces of brick work or concrete sur-faces of ceiling in cement mortar 1:4 for finished even and smooth (without using extra cement)

M & L for preparing new plastered surfaces of wall and applying two coats of oil bound distamper over and including a coat of 1 to 1.5mm average thick birla/ equivalent wall care putty and one coat of primer. (Note : Putty shall be measured and paid separately under relevant Item)

M&L preparing new/old plastered surfaces of wall and applying 1 to 1.5 mm thick layer of Birla/J K Wall care Putty all as specified and directed. .

M & L for preparing new plastered surfaces of ceiling and applying three coats of white wash.

Taking down chowkats or frame with shutter (without taking off shutter from the frame) n.exc 1.5sqm each

Taking down chowkats or frame with shutter (without taking off shutter from the frame) Exc 1.5 Sq m but n.exc 4.00 Sq m each

S&F of Powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F of Powder coated aluminium window/ventilator shutters, side hung/sliding type aluminium sections including necessary joining cleats, sash bars, glazing clips rubber neoprene packing, anodised aluminium snap beading, screws etc as per manufactures instruction & trade pactiice.

S&F 4.00mm thick figured glass, pin head type and glazing with rubber beading or with glazing clips, all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples.

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks, cooler stand and similar work con- forming to Fe.290.Gde-E-165 all as specified and directed.

M&L for 100mm butt hinges of stainless steel grade 202, 14 gauge thickness, medium weight of approved make fixed with pressed steel door frame/PVC door frame with screw complete all as specified and directed.

S & F 150 mm aluminium alloy handles, cast type anodised all as specified.

S & F 200mm aluminium anodised barrel tower bolts of extruded section and fixed.

S&F 250 mm Aluminium alloy, anodised sliding door bolt with hasp, staple (Bolt Type) and fixing, clips of sheet of extruded sections and fixing bolts.

S & F in repairs 25mm dia stainless steel tubular curtain rod medium quality including brackets for fixing of rod to wall complete all specified and as directed.

S & F in repairs stainless steel brackets decorative type for 25mm dia stainless steel tubular curtain rod at both end medium quality complete all specified and as directed.

M & L for 16 to 18 mm thick green marble (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking plateform and like including cement mortar 1:4 (10mm thick) and pointing in white cement (1:2) using marble dust with admixture of pigments to match with shade green marble all as specifed and as directed.

M&L for concealed point wiring complete with 1.5 Sqmm single core multistranded copper conductor PVC insulated and unsheathed FRLS cable 1100 volts grade drawn through and including non metallic rigid PVC conduit, medium grade minimum 20mm dia ISI marked and conduit accessories concealed in wall etc with sunken type pressed steel/welded MS terminal boxes made out of 1.2 mm MS sheet, 3mm thick laminated sheath top cover for mounting of fittings, switches, sockets outlets, regulators etc complete including provisining of 1.5 sqmm PVC insulated unsheathed FRLS cable 1100 volt grade with multi stranded copper conductor to common earth and connected to earth dolly for One light/fan/bell point controlled by one switch 6 Amp one way

One light/fan/bell point controlled by one switch 6 Amp one way

One 3 pin switch socket combination 6 amp on the independent board.

One 3 pin switch socket combination on same board with other switches.

One exhaust fan point controlled by one switch 6 Amp one way

S/Fix MCB DB factory made IP 42 protection class metal double door with 200 Amp rating bus bar 240/430V for fixing of MCBs/Isolators/RCCBs etc completed of following sizes:-

SPN 08 way

S&F MCBs 240/415 Volts 10 KA finger proof terminal, bio connect termination, label holder, 35 mm² terminal capacity, insulated sliding shutter, large two position dolly, ISI marked to be fixed on DB (DB will be measured and paid separately under respective items of sch A):-

MCB SPN 40 Amps.

MCB SP 5 to 40 Amps

M&L switch piano flush type single pole, one way 6amp .

M&L switch socket combination 5 pin 6 amp.

S/fix fan regulator electronic type 100Watt 20V-50Hz as directed by Engr-incharge

Supply and fix ceiling rose 65x17mm three terminals .

S& F lamp holder,PVC/Polycarbonate type and back plate suitable for batten fitting along with 09watt LED Lamp of make : Philips/Bajaj/Wipro

Supply and fixing ceiling fan 1200 mm sweep BEE 5 star rated including fixing of down rod and connection complete with & including provision of flexible three core PVC insulated multi-stranded copper conductor cable of size 0.50 sq mm from ceiling rose/connector to fan complete all as specified and directed. Make : Crompton Greaves or equivalent in Bajaj/Orient/Usha

Supply, Fixing, Testing and commissioning of 4' LED not less than 1X18W LED Batten with LED tube not less than 18 watt. Similar to Batten cat Part No.REGALBATTEN8UPTO1X22wSSBSWH and LED tube light cat part No.CRYSTAL1213T8DSTL18WLED865SGLASS of Make- Havells or equivalent in Make: Philips/Wipro/CG

M&L earthing complete with galvanized steel earth plate electrode 600mmX600mmX6mm buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, the earth electrode surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15cm on all side and connected to and including galvanized earth lead wire 4.0 mm dia upto 7.5 mtrs long by means of nuts and bolts, check nuts and washers of GI and connected to earhing test point and earth dolly all as shown in electrical plate No 3 of MES schedule Part-I, and testing on completion including necessary excavation and earth work in any type of soil, PCC(1:3:6) type C1 chamber, CI Cover with cast iron frame, funnel with watering pipe 20mm dia medium grade, wire mesh and lugs, GI protection pipe15mm dia, light grade 7.5 mtr long for protection of earth lead upto test point etc all as specified and as directed.

M&L for sand cushoning, to cable with river sand and punning to provide required cover for UG cables all as directed at site. Note: Punned hickness shall measured.

M&L brick protection cover to electric cable with class 'B' bricks laid dry and flat abutting each other with gap between adjascent not exceeding 10mm.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of 6 sq mm 2 core

M&L for galvanized steel tubing light Grade of 40 mm dia protection of cable fixed to pole/walls or laid in floors, road crossing ducts with all necessary fittings and fittings and fixed with clamps, bolts, nuts and washers etc complete all as specified and directed.

M&L for making hole in existing wall of 230mm thickness, suitable for housing of 225 mm sweep Exhaust fan complete including grouting of 04 Nos bolt fasteners, PCC work etc including making good disturbed surfaces

S&F of Exhaust fan 225 mm sweep with minimum airflow/air delivery 720 Cmh, 03 blades, light weight, rust proof iron body & blades, self opening louvers for protection from birds & rain water, IP-55, 230 Volt AC supply, rated power input not more that 45watt, connecting up including provison of cable from ceiling rose to fan. Make : Crompton Greaves, Model : Trans AIR Reversible

Shree Vaishno Enterprises