Supply of Tools Equipments and Machineries of Fitter Trade

Steel Rule 15 cm with metric & British graduation - 150 mm, Stainless Steel

Try Square 15 cm blade. - 150 mm

Caliper inside 15 cm spring - 150 mm

Caliper 15 cm hermaphrodite - 150 mm

Caliper outside 15 cm spring - 150 mm

Divider 15 cm spring - 150 mm

Straight Scriber 15 cm. - 150 mm

Centre Punch 10 cm - 10 mm and Length 120 mm

Screw driver 15 cm - 150 mm insulated flat type

Chisel cold flat - 20 mm X 150 mm High Carbon Steel

Hammer ball peen With handle - 0.45 kg. (1 lb)

Hammer ball peen With handle - 0.22 kg. (1/2 lb)

File flat 25 cm. second cut - 250 mm

File flat 25 cm. smooth - 250 mm

File half round second cut 15 cm. - 150 mm

Hacksaw frame fixed 30 cm. - 300 mm

Safety goggles.

Dot slot punch 10 cm. - 100 mm

Steel Rule 30 cm Graduated both in Metric and English Unit - 300 mm

Straight edge steel - 300 mm or above

Spirit Level metal Type - 2 (300 mm Basic length accuracy 0.1 mm/Meter)

Stud Extractor EZY – out Set 0f 8

Combination Set 30 cm. - 300 mm

Micrometer 0 – 25 mm outside.

Micrometer 25 – 50 mm outside.

Micrometer 50 –75 mm outside.

Micrometer inside 25 - 50 mm with extension rods. (Accuracy 0.01 mm with extension rods upto 150 mm)

Vernier caliper 15 cm -150 mm

Vernier height gauges 30 cm - 300 mm

Vernier bevel protractor blade with Acute Angle attachment

Screw pitch gauge - 0.25 to 6 mm

Wire gauge, metric standard.

Surface plate CI / Granite with Stand and Cover - 600 x 600 mm

Marking table (Mild Steel) 900 x 900 x 900 mm.

Universal scribing block 22 cm - 220 mm

V-Block pair with clamps - 150 x 100 x 100 mm

Angle plate - 150x 150 x 250 mm

Punch letter 3 mm set.

Punch number set 3 mm.

Portable hand drill (Electric) 0 to 13 mm Capacity

Drill twist straight shank 3 mm to 12 mm by 0.5 mm H.S.S

Drill twist taper shank 8 mm to 20 mm by 0.5 mm H.S.S

Taps and dies complete set in box With-worth.

Taps and dies complete set in box 5, 6, 8, 10, & 12 mm set of 5

File knife edge 15 cm smooth - 150 mm

File feather edge 15 cm smooth - 150 mm

File triangular 20 cm smooth - 200 mm

File round 20 cm second cut - 200 mm

File square 25 cm second cut - 250 mm

Feeler gauge - Gauge Feeler /Thickness - 0.05 mm to 0.3 mm by 0.05 and 0.4mm to 1 mm by 0.1 mm - 13 leaves

File triangular 20 cm second cut. - 200 mm

File flat 30 cm second cut safe edge - 300 mm

File flat 20 cm bastard - 200 mm

File flat 30 cm bastard - 300 mm

File Swiss type needle set of 12. Length - 150 mm

File half round 25 cm second cut. - 250 mm

File half round 25 cm bastard. - 250 mm

File round 25 cm bastard. - 250 mm

File hand 15 cm second cut. - 150 mm

File Card - 3" x 5 " size , brass or steel wire

Oil Can 0.25 liters. - 250 ml

Pliers combination 15 cm - 150 mm

Wooden handle forged Soldering iron copper bit - 230 V, 250 W, 350 gm

Blow Lamp 0.50 liters.

Spanner D.E. 6x7, 8x9, 10x11, 12x13, 14x15, 16x17, 18x19, 20x22 - 1 set each

Spanner adjustable 15 cm - 150mm

Interchangeable ratchet socket set with a 12 mm driver, sized10-32 mm set of 18 socket & attachments.

Double Ended tubular Box spanner set 6-25 mm set of 8 with Tommy bar.

Glass magnifying 7.5 cm - 75 mm

Clamp toolmaker 5 cm and 7.5 cm set of 2.

Clamp “C” 10 cm - 100 mm

Clamp “C” 20 cm - 200 mm

Hand Reamer Set (Tapar pin straigh flute) Nominal Dia 6,8,10,12,16 m

Machine Reamer parallel (Helical flute)12 - 16mm set of 5.

Scraper flat 15 cm. - 150 mm

Scraper triangular 15 cm

Scraper half round 15cm

Chisel cold 9 mm cross cut 9 mm X 150 mm diamond.

Chisel cold flat 9 mm X 100 mm

Chisel cold round noze. 9 mm X 100 mm

Drill chuck with key 12 mm.

Pipe wrench 40 cm - 400 mm

Pipe vice 100mm

Adjustable pipe tap set BSP with die set cover pipe size 1" or 3/4"

Wheel dresser (One for 4 units). Star/Dresser with Holder

Machine vice - Swivel Base 10 cm -100 mm

Machine vice 125 mm

Sleeve drill Morse 0 - 1, 1 - 2, 2 - 3., 3-4, 4-5

Vice bench 15 cm jaws - 150 mm

Bench working 240 x 120 x 90 cm.

Almirah 180 x 90 x 45 cm.

Lockers with 8 drawers (standard size).

Metal rack 182 x 182 x 45 cm

Instructor Table

Instructor Chair

Black board with easel.

Fire extinguisher (For 4 Units) CO2 type, 3kg capacity

Fire buckets.

Machine vice 100mm.

Wing compass 25.4 cm or 30 cm.

Hand hammer 1 kg. with handle.

Torque wrench (Standard/Ratchet type) (14 to 68 Nm)

Power tools for fastening Capacity 10-18 mm

Different profile gauges (Plat type) - For demonstration Metric Standard

Knurling tool (Diamond, Straight & Diagonal)

Indexable boring bar with inserts - 1" shank

Machine maintenance mannual for Lathe, Pedestal grinder, Drill machine, Power saw

Temperature gauge Range 0 - 150°C

Dowel pin ( straight) Dia. -1" Length -4" (Mat: Stainless Steel)

Standard Tap screws M3, M4, M5, M6, M8, M10, M12, M14, M16

Lapping plate Dia. -6"

Medium carbon Heat treated alloy steel Metric Studs and bolts along with nuts (for display) of standard length (May be manufactured in-house) M6, M8, M10, M12, M14, M16 (Standard)

Caps screws M6, M8, M10, M12

Drill gauges Letter drill gauge (A to Z) , Number drill gauge (1 to 60) , Metric drill gauge (1.5mm to 12.5mm, 30 holes)

Cast Iron Globe Valve (Flanged type) 150NB, Class# 150 Flange: ANSI125-B16.1

C.I. Sluice / Gate valve (flanged type) 150NB, Class# 150 Flange:ANSI125-B16.1

Stop cock 25NB (2-way, Threaded end)

M.S. Pipe 150NB, Sch.40, ERW, IS:1239

G.I. Pipe 25mm, Sch.40, ERW

Slip-on Forged steel Flange 150NB, ANSI-B16.5, Class#150

Bolt & Nut with washer (May be manufactured in-house) M20x2.5x90 Long (part thread - Hex. Head)

Pipe threading die with handle Ratchet type Die head of 1/2" , 3/4" and 1"

Jigs & Fixture (sample)-For demonstration (May be manufactured in-house)

M. S. Shaft (May be manufactured in-house) Bright M.S. round bar  80mm, 600mm long, Stepped  0mm on 300mm one end

Pulleys (for V-belt or Flat belt) to fit on 50mm dia. Shaft with key slot

Steel keys (May be manufactured in-house) to fit with keyslot of shaft & pulley

Damaged old spur gear to fit 50mm dia. Shaft

V-belt and Flat belt to fit on pulley

Packing gasket PTFE gasket roll small size

Washer, clutch, keys, jib, cotter & circlip minimum 25mm size, carbon steel material

Hollow punch Straight Shank Hollow Punch Sets 5-12mm

Drill Drift (May be manufactured in-house) 200mm hardened and black finish

Bearing different types each type of diameter 25mm (min.)

Lifting sling 8mm Nominal Dia. Single leg sling

Bearing extractor Universal gear puller 2 or 3 jaws adjustable

Pulley extractor Universal gear puller 2 or 3 jaws adjustable

Trammel 30cm. - 300 mm

Pocker.

Prick punch

Mallet.

Aviation Snips straight cut 30 cm - 300 mm.

Flat head hammers with handle.

Planishing hammer.

Snip bent left cut 25 cm. - 250 mm

Stake hatchet with leg 300x200x20 mm

Stake grooving 100x100x300 mm

Slip Gauge as Johnson metric set. 87 pieces set

Gauge snap Go and Not Go 25 to 50 mm by 5mm. Set of 6 pcs.

Gauge plug single ended 5 to 55 by 5 mm. Set of 11 pcs.

Gauge telescopic upto 8-150 mm.

Dial test indicator .01 mm on stand

Sine bar 125 mm.

Dial vernier caliper 0 – 300 mm LCO 0.05 mm. (Universal type).

Screw thread micrometer with interchangeable 0-25mm. Pitch anvils for checking metric threads 60

Depth micrometer 0-25 mm. Accuracy 0.01 mm with standard set of extension rods upto 200 mm

Vernier caliper 0-150 mm. L.C. 0.02 mm.

Digital Micrometer 0 – 25 mm outside. L.C. 0.001 mm.

Comparators Gauge dial indicator with stand and bracket LC 0.01mm.

Engineer‟s try square (knife-edge) 150 mm blade.

Surface roughness comparison plates N1-N12 grade

Digital Vernier caliper 0-200 mm. L.C. 0.001 mm.(Optional)

Vernier Bevel Protector Range 360deg, LC. : 5min(150mm blade)

Carbide Wear Block 1 mm - 2 mm

Lathe tools H.S.S. tipped set.

Lathe tools bit 6 mm X 75 mm HSS/Carbide

Lathe tools bit 8 mm x 75 mm. HSS/Carbide

Lathe tools bit 10 mm x 85mm. HSS/Carbide

Arm strong type tool bit holder Right.Hand.

Arm strong type tool bit holder Left.Hand.

Arm strong type tool bit holder straight.

Stilson wrenches 6 mm to 25 mm

Pipe cutter 6 mm to 50 mm wheel type.

Pipe bender machine spool type up to 25 mm cold bending. with stand manually operated.

Adjustable pipe chain tonge to take pipes up to 300 mm.

Adjustable spanner 38 cm long.- 380 mm

SS and SC centre lathe (all geared) with minimum specification as: Centre height 150 mm and centre distance 1000 mm along with 3 & 4 jaw chucks, auto feed system, safety guard, taper turning attachment, motorized coolant system, lighting arrangement & standard accessories.

Drilling machine pillar sensitive 0-20 mm cap with swivel table motorised with chuck & key. (Pls refer Terms & Conditions for detailed Technical Specifications)

Drilling machine bench - Sensitive 0-12 mm cap motorised with chuck and key.

D.E. pedestal Grinding machine with 200mm diameter wheels rough and smooth with twist drill grinding attachment. (Ps refer Terms & Conditions for detailed Technical Specifications)

Transformer welding set continuous welding current, with all accessories and electrode holder 60% Duty Cycle with Standard Accessories - 300 A, OCV 60-100 V

Welder cable to carry 300 amps. With flexible rubber cover

Lugs for cable

Earth clamps.

ARC welding table (all metal top) 1200 mm X 1200 mm X 750 mm with positioner

Oxy - acetylene gas welding set equipment with hoses, Oxygen & Acetylene cylenders, regulator and other accessories.

Gas welding table with positioner with Fire Bricks

Welding torch tips of different sizes for Oxy - Acetylene gas welding To fit nozzel no 1,2, & 3

Gas lighter.

Trolley for gas cylinders.

Chipping hammer.

Gloves (Leather)

Leather apron.

Spindle key for cylinder valve.

Welding torches nozzles no 1,2,& 3.

Welding goggles

Welding helmet with coloured flame retardent glass

Tip cleaner

Compressor unit : Please Refer Technical Specification for Detail Specifications

Pneumatic Trainer Kit, each consisting of the following matching components and accessories: Please Refer Technical Specification for Detail Specifications

Cut section model for pneumatic components

Hydraulic Trainer Kit, each consisting of the following matching components and accessories: Please Refer Technical Specification for Detail Specifications

Cut-section models for hydraulic components

Xtreme Engineering Equipment Pvt Ltd

Yashaswi Electronics