SPECIAL REPAIR REPLACEMENT OF SECURITY LIGHT POLES WITH STEEL TUBULAR POLE OH LT FEEDERS WITH UG CABLES SERVICE CABLES DISTRIBUTION CONTROL PANELS AND CONVERSION OF OH LINE IN TO UG CABLE AT MIL STN GANDHINAGAR

Amount

Excavating in trenches not exceeding 1.5m wide and not exceeding 1.5 m in depth, for laying of cable incl getting out soft/loose soil manually complete all as specified and directed by Engr-in charge.

Returning, filling in including spreading, levelling, watering and well ramming excavated soil in layers not exceeding 25 cm thick each, back in trenches after cables have been laid and tested,poles, stays , struts have been erected and tested all as specified and directed.

Removing excavated surplus soil (Soft/hard soil) obtained from excavation to a distance not exceeding 50 mtr and deposting where directed at a level not exceeding 1.5m above the starting point all as specified and directed.

Supply and laying sand cushioning for cable protection in trenches 8 cm before laying cable and 15 cm deep over the cable all as specified. Note : Depth of sand shal be measured as 18cm after punning.

Supply and laying sub class old 'B' burnt bricks, local available size, laid as cable protection cover complete all as specified and as directed.

Supply and Laying Class LV, Type I, flat, size 250mm x 150mm x 40 mm laid flat in trenches as protection to LT cable complete all as specified and as directed.

Supply, laying and testing cable XLPE Insulated galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 3.5 Core x 120 Sqmm.

All as per item No.6 here-in-before but of 3.5 x 70 sqmm.

All as per item No.6 here-in-before but of 3.5 x 50 sqmm.

All as per item No.6 here-in-before but of 3.5 x 35 sqmm.

All as per item No.6 here-in-before but of 3.5 x 25 sqmm.

All as per item No.6 here-in-before but of 4 x 16 sqmm.

All as per item No.6 here-in-before but of 4 x 10 sqmm.

All as per item No.6 here-in-before but of 2 x 10 sqmm.

All as per item No.6 here-in-before but of 2 x 6 sqmm.

All as per item No.6 here-in-before but of 2 x 4 sqmm.

Note:- For item 7 and 16 cable entry and exit shall be provided with metallic glands of suitable size and the cost shall be deemed to be incl in quoted rate

Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to using galvanised iron strip 25×4mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion all as specified and directed by ENgr-in-charge

M&L for horizontal drilling of size 40mm dia, in any type of soil, using trenchless technology suitable for insertion GI pipe and LT cables along the pipe complete all as specified and directed.

M&L for horizontal drilling of size 50mm dia, in any type of soil, using trenchless technology suitable for insertion GI pipe and LT cables along the pipe complete all as specified and directed.

Supply, installation, commissioning and testing, in repair, Main Panel board, LT (415 Volts, 50 Hz , 3-phase, 4 wire supply),CPRI approved, plinth mounted, factory made, outdoor type, weather and vermin proof (Protection Class IP-54) made out of 50mm x 50mm x 5mm angle iron frame and 3.15 mm thick MS Sheet CRCA sheet powder coated with front & back hinged opening, rubber lining, locking arrangement, painted externally and internally with two coats of synthetic enamel gray paint (First Quality) over a coat of red oxide primer, grouting panel through MS angle iron of size50mm x 50mm x 5mm , 0.5 mtr in ground and 0.35 mtr over the ground including excavation & earth work in any type of soil and PCC (1:3:6) type C-2 using 40mm graded stone aggregate complete comprising of the followings:- (a) Incoming supply:- (i) 40 X 10 mm. EC grade aluminium busbars of 04 strip - 01 Nos (ii) Mains incomer, 200 A, 25 kA, 4-pole MCCB with adjustable thermal-magnetic release - 01 No (iii) MFM without RS-485 port, class - 1.0- 01 Nos (iv) Indicating lamp Neon type for R-Y-B - 3 Nos (vi)Extended rotary handle & spreader terminals for above MCCB-01 Nos (vii)6 A TP MCB-01 Nos (viii) 6 A SP MCB-01 Nos (ix) CT - 125 / 5 A, class - 1.0-03 Nos (b) Outgoing supply:- (i) MCCB, thermal and magnetic setting, 3 pole, AC, 415volts,125 Amp rating, 25KA rupturing capacity - 02 Nos (ii) (i) MCCB, thermal and magnetic setting, 3 pole, AC, 415volts,100 Amp rating, 25KA rupturing capacity - 02 Nos (iii) Extended rotary handle for above MCCB - 01 Nos (iv) Wire - 16 sq. mm. for power wiring (v) Timer switch astronomical type for street light operation 12 kw 3 phase ( 100Nos x 60 watt street light ) (vi) Terminal connectors for power connections complete all as specified and directed by Engr-in-Charge

MAIN BUSBAR SIZE- 40 X 10 mm. EC grade aluminium busbars MAIN BUSBAR SIZE (For neutral)-40 X 10 mm. EC grade aluminium busbars EARTHING BUS 40 X 5 mm. EC grade aluminium busbars PANEL MOUNTING-Floor mounted CABLE ENTRY-Bottom for both incoming and outgoing PANEL FABRICATION-From 11G CRCA sheet steel FINISHING-Powder coating (min. 80 micron) after 7-tank process to shade RAL-7035 PANEL DIMENSIONS- App. 750 mm. (H) X 1200 mm. (W) X 400 mm. (D)

S&F GI tubing light grade galvanised with all fittings & fixed complete wall/pole for 40mm bore complete all as specified and directed.

S&F GI tubing light grade galvanised with all fittings & fixed complete wall/pole for 50 mm bore complete all as specified and directed.

M and L for dismantling stay assembly from poles any type and any size complete all as specified and directed by Engr-in-charge.(Demolition of concrete, etc. and excavation measured separately)

M/L for PCC (1:2:4) type B-1 using 20mm graded aggregate as in foundation/surface repair etc complete all as specified and directed.

S and F PVC insulated and PVC sheathed copper conductor cable of size 1.5 Sqmm, 3 core, 1100 volts grade, multistranded, passing throuth pipe, on pole/wall from juntion box to street light fitting complete all as specified and directed by Engr-in-charge

S&F in repair MS made junction box of CRCA sheet min thickness 1.6 mm, outdoor type, size 250 x 200x 150 mm factory made,, with one No SP MCB of 6 Amp rating, class-B and terminal assembly with min 4 terminals necessary clamps and bolts etc of MS iron including connecting with street light cable complete all as specified and directed by Engr-in-charge.

Supply and fix in repair, Digital time switch, Electro mechnical type with programming using captive segments with 24 hrs timing setting, contactor 230 volt AC coil voltage with 415 volt AC power contact AC 3 duty. 40 Amps rating including 40 Amp 3 Nos terminal block for input & output 03 pole neutral & spare one of 03 pole & neutral (TPN) including 4 module weather proof cabinet IP-65 protection complete with electrical internal connection complete all as specified and as directed.

M & L for cutting chases for fixing of GI Pipe of any size on wall / Plinth and including PCC work for making good the distrub surfaces of wall and plinth, including white wash for matching the existing wall complete all as specified and directed .

Material and labour for Taking out Security Light OH Line any type and size with ACSR conductor after taking electrical shutdown complete all as specified and directed

Material and labour for Taking out Broken / detreorated Security Light PCC Poles with cross arms complete after taking electrical shutdown all as specified and directed

M/L for PCC (1:4:8) type D-2 using 40mm graded aggregate as in foundation/surface repair for pole / Platform etc complete all as specified and directed.

M/L for PCC (1:3:6) typeC-1 using 20mm graded aggregate as in foundation/surface repair for pole / Platform etc complete all as specified and directed.

M&L for plain cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate for padestal/coping around poles, including necessary form work, finishing even and smooth without using extra cement, all as specified and directed.

M&L Steel Tubular swaged welded pole, type 410 SP-31 (9 metres long) including cast iron base plate, Finial Taper Plug, Cap, Mild Steel Bolts, Nuts, Screws etc. Including applying two coat of Black bituminous Paint Internally and Externally up to Planting depth and applying two coats of aluminium painting over a coat of red oxide primer including writing MES street light Pole and Blue reflector strip with synthetic enamel paint ( First Grade/quality) complete all as specified and directed Note: Earthwork and PCC work will be measured and paid seperately.

Supply and fixing LED street light fitting 60 Watt 230 V AC outdoor type with high pressure die cast aluminum housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP66 protection complete including taking out old unserviceable fitting of any type complete all as specified and as directed.

Supply, installation, commissioning and testing, in repair, LT street light panel , (415 Volts, 50 Hz , 3-phase, 4 wire supply),CPRI approved, plinth mounted, factory made, outdoor type, weather and vermin proof (Protection Class IP-54) made out of 50mm x 50mm x 5mm angle iron frame and 3.15 mm thick MS Sheet CRCA sheet powder coated with front & back hinged opening, rubber lining, locking arrangement, painted externally and internally with two coats of synthetic enamel gray paint (First Quality) over a coat of red oxide primer, grouting panel through angle iron, 0.2 mtr in ground and 0.5 mtr over the ground including excavation & earth work in any type of soil and PCC (1:3:6) type C-2 using 40mm graded stone aggregate complete comprising of the followings:- (a) Incoming supply:- (i) Mains incomer, 63 A, 25 kA, 4-pole MCCB with adjustable thermal-magnetic release - 01 No (ii) Indicating lamp Neon type for R-Y-B - 3 Nos (iii)Extended rotary handle & spreader terminals for above MCCB-01 Nos Outgoing (i) DigitalTimer switch for street light operation with 40 A contactor, 230 Volt AC coil voltage with 415 volt AC power contact AC 3 duty. 40 Amps rating including 40 Amp 3 Nos terminal block for input & output 03 pole nuetral & spare one of 03 pole & neutral (TPN) (ii) 40 A TP MCB-01 Nos. MAIN BUSBAR SIZE- 25 X 5 mm. EC grade aluminium busbars MAIN BUSBAR SIZE (For neutral)-25 X5 mm. EC grade aluminium busbars EARTHING BUS 25 x 5 mm. EC grade aluminium busbars PANEL MOUNTING-Floor mounted CABLE ENTRY-Bottom for both incoming and outgoing PANEL FABRICATION-From 11G CRCA sheet steel FINISHING-Powder coating (min. 80 micron) after 7-tank process to shade RAL-7035 PANEL DIMENSIONS- App. 700 mm. (H) X 700 mm. (W) X 300 mm. (D)

M&L for earthing complete with galvanized steel earth plate electrode of 60 cm x 60 cm x 6mm thick buried directly in ground [earth pit not less than 2.25 metre deep below normal ground level] with top edge of the plate not less than 1.5 m below normal ground level, connected to galvanized earth Lead 4 mm by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No. 3 of MES SSR Part I connected to earth test point using earth strip of 25x4mm as earth lead all as specified and testing on completion including provision of earth lead protected by 20 mm dia light grade GI pipe & watering pipe shall be 15 mm bore medium grade GI pipe including all excavation and earth work in any type of soil, PCC pit with RCC cover, char coal, salt, funnel etc complete. Note : Rate quoted by tenderers shall be deemed to include for following provisions:-[i]. Excavation & earth work in any type of soil including removing of surplus material upto 50 M.[ii]. PCC 1:3:6 type C1 using 20mm graded stone aggregate in pit & 40mm thick precast RCC 1:2:4 type B1 cover 50x50 cm with 8mm TMT bars @ 10 cm C/C both ways with handles.[iii]. Main earthing lead from earth electrode to test point upto 7.5 mtr.[iv]. Funnel with watering pipe [GI pipe] 15 mm bore [ISI marked] medium grade & copper lugs, charcoal & salt as reqd.[v]. GI protection pipe of size 20 mm bore light grade 7.5m.

Supply, installation, commissioning and testing, in repair, Junction Box , LT (415 Volts, 50 Hz , 3-phase, 4 wire supply),CPRI approved, plinth mounted, factory made, outdoor type, weather and vermin proof (Protection Class IP-54) made out of 50mm x 50mm x 5mm angle iron frame and 3.15 mm thick MS Sheet CRCA sheet powder coated with front & back hinged opening, rubber lining, locking arrangement, painted externally and internally with two coats of synthetic enamel gray paint (First Quality) over a coat of red oxide primer, grouting panel through angle iron, 0.2 mtr in ground and 0.5 mtr over the ground including excavation & earth work in any type of soil and PCC (1:3:6) type C-2 using 40mm graded stone aggregate complete comprising of the followings:- (a) Incoming supply:- (i) Mains incomer, 125 A, 25 kA, 4-pole MCCB with adjustable thermal-magnetic release - 01 No (ii) Indicating lamp Neon type for R-Y-B - 3 Nos (vi)Extended rotary handle & spreader terminals for above MCCB-01 Nos (vii) 6 A TP MCB-01 Nos MAIN BUSBAR SIZE-30 X 10 mm. EC grade aluminium busbars MAIN BUSBAR SIZE (For neutral)-30 X 10 mm. EC grade aluminium busbars EARTHING BUS 30 X 10 mm. EC grade aluminium busbars PANEL MOUNTING-Floor mounted CABLE ENTRY-Bottom for both incoming and outgoing PANEL FABRICATION-From 11G CRCA sheet steel FINISHING-Powder coating (min. 80 micron) after 7-tank process to shade RAL-7035 PANEL DIMENSIONS- App. 750mm. (H) X 700 mm. (W) X 400 mm. (D)

Taking out old serviceable cable any type and any size and keep in safe custody for relay at site incl returning filling of soil at site complete all as specified and directed by Engr-in-charge. Note:- Excavation and Returning filling will be paid seperately

Relaying of old serviceable cable any type and any size by connecting in panel through glands and terminating as required at site incl all accessories such as Lugs, fastener etc complete all as specified and directed by Engr-in-charge. Note:- Excavation, removal and Returning filling will be paid seperately

Taking out carefully from existing grouted position PCC/steel tubular poles by removing all the cradles, cross arm, complete incl all as specified and directed by Engr-in-charge. Note:- Taken out poles should be transported out of the mil stn Gnr to the charge of the contractor rate of which shall deemed to be incl in quoted rate

Taking out Old UNSV ASCR conductor at site complete all specified and directed by Engr-in-charge

M and L for repair of cable by insertion of straight through joint cold shrink type for LT cable 10 Sqmm 2 core with all accessories all as specified and directed by Engr-in-charge.

M and L for repair of cable by insertion of straight through joint cold shrink type for LT cable 16-25 Sqmm 3.5/4 core with all accessories all as specified and directed by Engr-in-charge.

M and L for repair of cable by insertion of straight through joint cold shrink type for LT cable 35-70 Sqmm 3.5/4 core with all accessories all as specified and directed by Engr-in-charge.

M and L for repair of cable by insertion of straight through joint cold shrink type for LT cable 95 -120 Sqmm 3.5 Core with all accessories all as specified and directed by Engr-in-charge.

M and L for dismantling cross-arms of M.S. channel or angle sections etc. complete and setting aside for re-use with in 50m complete all as specified and directed by Engr-in-charge.

M and L for dismantling insulators from poles any type and any size complete all as specified and directed by Engr-in-charge.

Excavating in trenches not exceeding 1.5m wide and not exceeding 1.5 m in depth, for taking out LT cables any size/type etc in any kind of soil by mechanical means (Hydraulic excavator) complete all as specified and directed by Engr-in charge.

Relaying of old 'B' burnt bricks, any size laid as cable protection cover complete all as specified and as directed.

Electricals India (BID ID -3369720)

Abhishek Enterprises (BID ID -3367369)

BK CONSTRUCTION (BID ID -3366828)

JYOT ENTERPRIES (BID ID -3378893)

TRIMURTHI ENTERPRISES (BID ID -3366900)

MONA GENERATOR SEVICES PVT. LTD. (BID ID -3370986)

Vending Services And Solutions (BID ID -3370403)