8538/e8

Amount

Demolition of cement concrete (unreinforced ) in ground floors and pavings n exc 15cm thickness ( below or above ground level )

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the permises including necessary disposal of cracked tiles all as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C-2 ( using 40mm graded crushed stone aggregate ) in floorings, foot paths, hard standing, plinth protection etc, including finishing the top surface even and smooth without using extra cement all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B-0 using 12.5 mm graded crushed stone aggregate as in floor & finishing the top surface even and rough for receiving floor finishes all as specified and as directed.

M&L for Non-skid joint free ceramic coloured tiles 7mm to 8mm thick area of each tile exceeding 0.18 but not exceeding 0.38sqm, in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of the tiles including 15mm thick screed bed or bedding layer of morter in CM 1:6 for laying floor finishes all as specified and as directed.

M&L for Non-skid ceramic coloured tiles 7mm to 8mm thick area of each tile exceeding 0.11 but not exceeding 0.18 sqm, in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of the tiles including 15mm screed bed or bedding layer of morter in CM 1:6 for laying floor finishes all as specified and as directed.

M&L glazed ceramic coloured tiles in vertical surfaces 450x350x 7mm set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of the tiles including rendering 10mm thick in CM 1:4 all as specified and as directed.

Demolition Brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone work and precast concrete articles all as specified and as directed.

M&L PCC (1:3:6 ) type C-1 (using 20mm graded crushed stone aggregate) as in coping including form work all as specified and as directed.

M&L pre-cast cement concrete block masonry 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) with solid block exc 10 cm in width and set in CM 1:6 all as specified and as directed.

Taking down cement plaster on brick or concrete walls including racking out joints, hacking for key, scrubbing down with water all as specified and as directed.

M&L rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finished surfaces even and smooth without using extra cement using water proofing compound all as specified and as directed. ( WPC shall be measured and paid separately )

M&L for rendering 15mm thick on other than fair faces of brick work or concrete surfaces in cement morter 1:6 finished surfaces even and smooth without using extra cement all as specified and directed.

Supply only integral water proofing compound (CICCO No 1/SIKA/SAP seal/ACCOPROOF )

M&L preparing new plastered surfaces of walls and applying two coats of oil emulsion white or tinted all as specified and directed.

M&L for preparing new plastered surfaces of walls and applying two coats of cement base paint over a coat of primer all as specified and directed.

M&L two coats of white wash on walls including preparation of new plastered surfaces all as specified and directed.

Taking down chowkats or frame with shutters ( without taking off shutters from the frame ) area not exc 1.5 sqm each and removing from site of work all as specified and directed.

Taking down chowkats or frame with shutter w/o taking off shutter from the frame area exc 1.5 but n exc 4 sqm each and removing from site of work all as specified and directed.

Taking down shutters of any description area exc 1.0 Sqm but n.exc 2.0 Sqm each and removing from site of work all as specified and directed.

Taking down steel windows/ventilatior of any description and of any type including guard bars all as specified and directed.

S&F second class hard wood plain, solid, straight chowkats and frames wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints all as specified and directed.

S&F for mild steel work as in band, strap, hold fast, clamp, cleat, hook, hinges base tie for floor, frame, support or stay for rain water pipe and other similar items conforming to Fe-410-0 or Fe-310-0 all as specified and directed.

S&F 35 mm thick factory made second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass or gauze etc divided into square with plain, chamfered or rounded mitred and rebated sash bars any numbers edges of framing plain, chamfered or rounded fitted with cut mitred beads for securing glass etc, the size of members of shutters shall be as specified in SSR part I, section 8, clause 8.24 ( a) all as specified and directed.

S&F 35mm thick flush shutters, solid core constructions with particle board core and commercial type ply wood face (BWP type) including lipping/frame to match all round all as specified and as directed.

M&L for preparation of new or previously untreated surfaces of wood and wood based materials not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer all as specified and as directed.

S&F 100 mm butt hinges, medium weight, cold rolled mild steel all as specified and directed.

S&F 150mm aluminium anodised barrel tower bolts of extruded section all as specified and directed.

S&F 250mm aluminium alloy, anodised, sliding door bolt with hasp, staple ( bolt type ) and fixing clip of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast- aluminium alloy all as specified and directed.

S&F for 150mm extruded aluminium alloy handles, fabricated type anodised all as specified and directed.

S&F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, devetailed or welded all as specified and directed.

S&F for steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, devetailed or welded all as specified and directed.

S&F mild steel work in framed work such as grills framed guard bars, gratings, ladders etc with ends of bars shouldered and/or riveted or forged into spikes and similar work conforming to Fe-290. Gde-E-165 all as specified and directed.

M&L preparation of new or undecorated steel surfaces and applying two coats of synthetic enamel paint (ordinary tint ) over a coat of red oxide primer on roof or wall all as specified and directed.

Hacking out old broken glass of any thickness size quality or description from steel/wooden frames glazed with oil putty or pins/spring clips all as specified and directed.

S&F 3mm thick sheet glass, ordinary quality and glazing with oil putty in square metre in each pane nexc 0.5sqm each pane all as specified and directed.

S&F in repair 3mm thick sheet glass, ordinary quality and glazing with oil putty in square metre in each pane not exc 0.50sqm all as specified and directed.

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperature 1.18mm and fixed with tinned tacks or galvanised wire staple all as specified and directed.

S&F in repair galvanised mild steel wire cloth 0.56mm nominal dia wire and average width of aperature 1.18mm and fixed with tinned tacks or galvanised wire staple all as specified and directed.

S&F in repairs vitreous china squatting pan Orrisa pattern of size 580X440mm white with integral foot rest 'P' trap including connection to trap and flush pipe anti-syphonage pipe including making good to floor all as specified and directed.

S&F PVC connections 15mm size with PTMT nuts of length 600mm all as specified and directed.

S&F in repairs 15mm bore stop valves/angle cock, cast copper alloy, fency type, chromium plated with long shank and cup (concealed type) screwed down high pressure, screwed both ends for iron pipe or for unions all as specified and directed.

S&F in repairs brass CP mixer for mixing hot and cold water screwed down for iron pipe all as specified and directed.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons, laid, bedded in any type of mortar all as specified and directed.

M&L machine cut mirror polished kota stone slab flooring 20mm (+ 2mm) thick laid over and including 20mm (+ 2mm) thick screed bed or bedding layer in cement mortar 1:4 as base laid and jointed with grey cement slurry mixed with pigment to match the shade including rubbing, polishing all as specified and directed.

S&F in repair vitreous china wash hand basin white flat back of size 550x400 mm including PVC waste pipe 32 mm bore and CP waste coupling with and including a pair of suitable mild steel brackets, fixed all in repairs, including cutting for or pinning in and making good disturbed portion as required all as specified and directed.

S&F in repair vitreous china wash down water closet pan (pedestal pattern), white including white plastic seat cover with mild steel CP hinging device, suitable brass CP wash jet with 1.00 to 1.50m long tube (Make of Jet 'Praayag' Cat Part No 5211 or Equivalent) including making connection to inlet flush pipe, & to 'P' or 'S' drain trap, including supply of long special 'P' or 'S' trap and making good the disturbed portion all as specified and directed.

S&F in repair for bib taps, cast copper alloy, chromium plated, long body with capstan head, screwed for iron pipe 15 mm bore or for brass furrule all as specified and directed.

S&F in repair for bib taps, cast copper alloy, chromium plated, small body with capstan head, screwed for iron pipe 15 mm bore or for brass furrule all as specified and directed.

S&F in repair angle stop valve (Angle cocks), cast copper alloy, chromium plated with capstain head & cup, screwed down high pressure, screwed both ends for 15 mm bore iron pipe or for union, all as specified and directed.

S&F in repair pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe 15 mm bore all as specified and directed.

S&F in repair brass shower rose 125 mm size (chromium plated) with swivel joint suitable for 15 mm bore iron pipe all as specified and directed.

S&F in repair for PVC valveless syphonic action type, flushing cistern, low level 10 litres capacity, white with inlet, ball valve, float and handle including brackets with and including PVC flush pipe 32 mm bore & making connections to PVC connections all as specified and directed.

S&F in repair for CP towel rail 20mm dia , D type 600 mm long between flanges with CP screws and wooden/plastic cleats having weight not less than 170gms each all as specified and directed.

M&L PVC waste pipe, 90 cm long suitable for 32mm/40mm dia with waste coupling all as specified and directed.

M&L for CP waste coupling of 32mm/40mm dia complete all as specified and directed.

Taking up or down 15mm bore GI steel tubing and connections, including cleaning for refixing or removal to store all as specified and directed.

Taking up or down for 20mm bore GI steel tubing and connections, including cleaning for refixing or removal to store all as specified and directed.

Taking up or down for 25mm bore GI steel tubing and connections, including cleaning for refixing or removal to store all as specified and directed.

S&F for GI water tubing, medium grade, 15mm bore ISI marked with all fittings and fixtures fixed to wall or laid in floor all as specified and directed.

S&F GI water tubing, medium grade, 20mm bore ISI marked with all fittings and fixed to wall or laid in floor all as specified and directed.

S&F GI water tubing, medium grade, 25mm bore ISI marked with all fittings and fixed to wall or laid in floor all as specified and directed.

Fixing only old serviceable GI water tubig 15mm bore, any grade to wall and ceilings or laying in floors after necessary cleaning internally including all fittings & fixtures all as specified and directed.

Fixing only old serviceable GI water tubig 20mm bore , any grade to wall or ceilings or laying in floors after necessary cleaning internally including all fittings all as specified and directed.

Dismantling of water tank and removing to store of capacity exc 250 litre but not exc 500 litres all as specified and directed.

Dismantling of water tank and removing to store of capacity exc 500 litre but not exc 1000 litres all as specified and directed.

S&F rotational moulded PVC water storage tank 500 litres capacity conforming to IS-12701(1989) cylindrical vertical type multi-layered with closed top including inlet, outlet and wash out holes of approved make hoisted and fixed in position all as specified in SSR Part I (Make:SINTEX/POLYCON) including 20mm ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 210 gms) all as specified and directed.

S&F rotational moulded PVC water storage tank 1000 litres capacity conforming to IS-12701(1989) cylindrical vertical type multi-layered with closed top including inlet, outlet and wash out holes of approved make hoisted and fixed in position all as specified in SSR Part I (Make:SINTEX/POLYCON) including 20mm ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 210 gms) all as specified and directed.

S&F in repairs 15mm bore gun metal, globe or gate valves with iron wheel head, screwed both ends for iron pipes all as specified and directed.

S&F in repairs 20mm bore gun metal, globe or gate valves with iron wheel head, screwed both ends for Iron pipes all as specified and directed.

S&F in repairs 25mm dia bore gun metal, globe or gate valves with Iron wheel head, screwed both ends for Iron pipes all as specified and directed.

S&F in repairs mild steel 300mm long oridnary rat tail rod pattern springs, including roller and roller plate all as specified and directed.

S&F in repair 600mmx450mm bevelled edge mirror of selelcted quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers all as specified and as directed.

M&L preparation of old decorated surfaces of walls and applying one coat of white wash all as specified and directed.

M&L preparation of old decorated surfaces of ceiling and applying one coat of white wash all as specified and as directed.

M&L for preparation of old decorated surfaces of wall and applying one coat of colour wash all as specified and directed.

M&L for preparation of old decorated surfaces of wall and applying one coat of oil bound distemper all as specified and directed.

M&L for preparation of old decorated surfaces of wall and applying one coat of cement base paint all as specified and directed.

M&L for preparation of old decorated wooden surfaces of any descreption exc 10 cm width or grith and applying one coat of synthetic enamel paint all as specified and directed.

M&L for preparation of old decorated steel surfaces and applying one coat of synthetic enamel paint (coptic green) (ordinary tint ) on roof or wall all as specified and directed.

Dismantling of false ceiling of any thickness including cover fillets all as specifed and directed.

Dismantling of frame work of timber scantling 40 Sq cm and over in section in any position all as specifed and directed.

S&F framework of suspended false ceiling GI exposed ceiling suspension system of grid size 600mm/600mm with main runner 38mmx24mm, cross tee 29mmx24mm and wall angle 24mmx24mm using 6mm thick (high pressure steam cured), conforming to IS 14862:2000, to be placed in a grid of GI system duly suspended with 4mm dia GI/MS bar hanger fixing with steel dash fastner or iron purlins from the roof with adjustment clip providing position for light fixture all as specified and directed.

S&F false ceiling of Everest designer boards of size 595mm x 595mmx4mm thick fixed on GI snap grid all as specified and directed.

S&F factory made solid panel PVC door shutters 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the styles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing all as specified and directed. Make : Rajshree Doors or equivalent as approved by GE

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing all as specified and as directed. Make : Rajshree Doors or equivalent as approved by GE.

Dismantling plain or corrugated steel sheeting of any gauge, thickness, including Nainital or similar pattern roof coverings all as specified and directed .

S&F pre painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified and directed.

M&L for 75mm thick PCC 1:4:8 type D2 using 40mm graded crushed stone aggregate as in sub base all as specified and directed.

M&L chequered cement concrete tiles 25cm x 25cm x 22mm thick set gointed and pointed in neat cement slurry in floors or pavings with grey cement and pigments over and including 20mm thick screed bed or bedding layers in CM 1:6 all as specified and directed.

Demolition of cement concrete (re inforced) in roof floors, beams, staircase, landings, chajjas, pillars etc and similar suspended works and removing materials from site of work all specified and directed.

M&L cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in precast slabs for covers of manholes and set in CM 1:6 including necessary form work and placing of manholes cover in position all as specified and directed.

M&L TMT bars 8mm dia cut to length ,bent to shape required,including cranking, bending spirally for hopping for columns, hooking ends and binding with and including mild steel wire ( annealed) not less than 0.90mm dia all as specified and directed .

M&L PCC 1:3:6 type C 1 (using 20 mm graded crushed stone aggregate) as in surface channel and drain all as specified and directed.

Extra for forming fair finished drain and channel 30 cm inner girth in cement concrete using extra cement including forms, mould, mittred/stopped ends all as specified and directed.

Removing sludge mixed with water n exc 50m and deposited where directed at a level n exc 1.5m above the starting point the solied working in foul position all as specified and directed.

Cleaning of sludge from existing manholes of any size and depth not exceeding 1.5 metre and removing of sludge to outside the MD land n exc 50m away all as specified and directed.

Cleaning of existing sewage lines of any size by rodding with split bamboo or any other means as spproved and removal of blockage including taking out existing RCC cover slab covers to facilitate cleaning debris/sludge in pipe line of any type all as specified and directed.

Excavation in trenches n exc 1.5 m deep and n exc 1.5 m width and getting out in soft/loose soil all as specified and directed.

Dismantling of 100mm internal dia CI or reinforced concrete drain pipes jointed in cement mortar and taking out trenches if required all as specified and directed.

S&F 100 mm dia cast iron (sand cast) soil waste and vent pipes in any length fixed with cement joints laid in trenches or in floor all as specified and directed.

M&L PCC 1:4:8 type D2 (using 40mm graded crushed stone aggregates) for concrete bed to 100mm bore drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested all as specified and directed.

Returning filling in including spreading , levelling, watering & well ramming in layers n exc 25 cm thick all as specified and directed.

S&F in repairs cast iron bend (sand cast) of any radius with oval access door including jointing with cement joints for (100 mm bore) all as specified and directed .

S&F in repair 100 mm bore cast iron floor trap/nahani trap with grating including jointing to waste pipe fixed in PCC 1:2:4 type B1 using 20mm graded crushed stone aggregates all as specified and directed.

Jahori Singh Pokhriyal

SIDHARTH CONSTRUCTION