CA NO GE(N)AMB-21/2025-26 REPAIR TO JOINERY, PLUMBING, SANITARY, ROOF, PLASTERING AND OTHER CONNECTED BLDG REPAIR WORK IN JCO/ORS/AREA OF MD ACCN-II OF AGE B/R-I UNDER GE (NORTH) AMBALA CANTT

Amount

Cleaning and removing all scale and dirt, etc from existing water storage tanks of capacity exceeding 250 litres and not exceeding 500 litres by emptying, drying and cleaning the tank by scrubbing the dust with wire brush from tank including cleaning from mouths of circulating pipes & writing on the tank with synthetic enamel paint not less than 200mm in height and 20mm wide of words in shape like cleaned on : 15.06.2024 to entire satisfaction of Engr-in–charge complete all as specified. (The rates includes for disconnecting of existing water tank, lowering if required and hoisting, reconnecting and refixing in same position after cleaning ) Note- The whole process of disconnecting, reconnecting and refixing in same position after cleaning shall be done on the same day, if failing so, Rs. 1000/- shall be deducted for each tank per day from the contractor due.

Taking down cement or cement lime plaster of any description on brick or stone walls etc including racking out joints, hacking for key scrubbing down with water etc., complete, all as specified and as directed by the Engineer–in–Charge.

Material and labour for rendering 15mm thick in cement plaster (1:4) on any faces of brick work or concrete wall surfaces and finished even and smooth without using extra cement up to height of double storey bldg, including necessary scaffolding etc., complete all as specified and as directed by the Engineer–in–Charge.

Material and labour for rendering 10mm thick in cement plaster (1:6) on any faces of brick work or concrete wall surfaces and finished even and smooth without using extra cement up to height of double storey bldg, including necessary scaffolding etc complete all as specified and as directed by the Engineer–in charge.

Material and labour for rendering 5 mm thick on ceiling surfaces of brick work or concrete surfaces in cement mortar 1:3 and finished even and smooth without using extra cement complete all as specified and as directed by the Engineer–in–Charge.

Material and labour for preparation of new plastered /concrete surface of wall applying of two coats of cement base paint over a coat of alkali resistant primer complete all as specified and directed.

Material and labour for preparation of new plaster surface on walls and applying two coats of acrylic distemper over a coat of alkali resistant primer over and including 1 to 2 mm thick wall care putty white cement based in one or two coats to achieve smooth surfacescomplete all as specified and as directed.

Material and labour for preparation of new plastered surface of ceilling applying three coats white wash, complete all as specified and directed.

Material and labour for preparation of old treated surfaces of walls, cornices etc. (plastered or unplastered) by brooming down, steel wire brushing, scraping down smoke soot, moulds, moss, efflorescence salts, trading oil and greasy spots etc, up to any height of including necessary scaffolding and applying one coat of acrylic distemper on wall surface etc., complete, all as specified and as directed

Material and labour for preparation of old plastered surface of ceilling applying one coat white wash, complete all as specified and directed.

Material and labour for preparation of old wooden painted surfaces and applying one coats of synthetic enamel paint on wooden surfaces of any description, not otherwise described, over 10cm width or girth complete, all as specified and as directed.

Material and labour preparation of old painted steel and iron surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and as directed by the Engineer–in–Charge.

Material and labour preparation of new steel and iron surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over and incuding a coat of red oxide primer complete all as specified and as directed by the Engineer–in–Charge.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exe 15 cm thickness (below or above ground level) complete, all as specified and as directed

Material and labour for 75mm thick PCC 1:4:8 type D-2 (using 40 mm graded mechanically crushed stone aggregate) as in sub base to floor /hardstanding etc finished even and fair, complete all as specified and directed.

Material and labour for providing 50 mm thick cement concrete 1:3:6, type C–1 (using 20mm graded crushed stone aggregates) as in plinth protection laid in alternate bays (n exc 2 Sqm each) and finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight, complete all as specified and directed.

Material and labour for 25mm thick PCC 1:2:4, type B–0 (using 12.50mm graded crushed stone aggregates) finished even and fair for levelling or base of floor finishes, complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete, all as specified and as directed.

Material and labour for granite black (of any type) tiles 16 to 18mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing over 15mm thick screed bed in cement mortar (1:6), as in steps, cooking platform, and including cutting 25mm dia hole for gas pipe complete all as specified and directed.

Material and labour for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations,. complete all as specified and directed.

Supply and fixing non skid ceramic colour tiles joint free premium /1st quality 7 to 8mm thick (square /rectangular) area of each tiles exc 0.06 sqm but n exe 0.11 sqm, in floor etc, set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

Supply and fixing glazed ceramic colour tiles joint free premium /1st quality in vertical surface, dado, skirting etc of size 300X600X7 to 8mm thick, set and jointed in neat cement slurry and pointed in coloured cement to match including 10 mm thick cement plaster in cement mortar (1:4) on wall of brick /concrete surfaces, complete all as specified and directed.

Material and labour non skid coloured ceramic tiles joint free premium /1st quality 8 to 10 mm thick, (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and inculding 15mm thick screed bed in cement mortar (1:6), complete all as specified and directed

Material and labour non skid coloured ceramic tiles of 8 to 10 mm thick, of same description as of floor tiles as in serial item No 23 above but 100 to 150mm in height as in skirting, set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match over and including 10mm thick rendering on fair faces of brick /concrete surfaces in cement mortar (1:4), complete all as specified and directed

Material and labour for machine cut kota stone slab flooring 18 to 22 mm thick (each slab size not less than 550mm x 550mm) in floor, set and jointed in neat cement slurry with grey cement mixed with pigment to match the shade of the slab including rubbing and polishing (granite finish) over and including 15 mm thick screed bed in CM 1:4 complete all as specified and as directed by the Engineer-in-Charge.

Material and labour 18 to 20 mm thick machine cut kota stone slab as in skirting, riser of steps, dado & pillar verticle surfaces etc. over and including 10mm thick screed layer in cement mortar 1:4 set and jointed in neat cement slurry mixed with pigment to match the shade including grinding and polishing complete all as specified and directed.

Supply and fixing as in repair, water storage tank, 500 ltr capacity, HDPE triple layer, white colour, conforming to IS, fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm dia high pressure with polythene float and flynut, screwed and suitable for iron pipe 20 mm bore and including 20mm bore tank nipple & one 20mm GI union at outlet and including disconnecting and dismantling of existing water tanks and removing from site all as specified in SSR Part–I complete, all as specified and as directed.

Cutting chases to brick wall built in cement mortar, pinning in making good to facing where required and pointing in CM 1:3 to edges of landing, steps, cills, sunsheds, shelves, lintel etc and cutting chases for concealed water tubing etc and making good cutting not exc 10 cm girth complete all as specified and as directed by the engineer - in- charge

Supply and fixing for galvanised iron tubing 20mm bore medium grade with all fittings and fixed complete to wall and ceiling or laid in floors, including taking down of existing unserviceable GI tubing including all fittings etc complete all as specified and directed.

Supply and fixing for galvanised iron tubing 15mm bore medium grade with all fittings and fixed complete to wall and ceiling or laid in floors, including taking down of existing unserviceable GI tubing including all fittings etc complete all as specified and directed.

Supply and fixing 15mm bore cast copper alloy fancy type, chromium plated stop valves with long shank and cup (concealed type), screwed down, high pressure with capstan head, screwed both ends for iron pipe or for unions as in repair, complete, all as specified and as directed.

Supply and fixing in repair stop valves /angle valve chromium plated fancy type, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

Supply and fixing in repair 15mm bore pillar taps cast copper alloy, with capstan heads, chromium plated, screwed down, fancy type high pressure, with or without lettred 'HOT or COLD' with long screwed shank and fly nuts complete all as specified and directed.

Supply and fixing in repair 15mm bore long body bib taps cast copper alloy fancy type, chromium plated, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

Supply and fixing in repair pvc connection 15mm size PTMT nuts of length 450mm, complete all as specified and directed.

Supply and fixing in repair vitreous china wash basin white, flat back, size 550x400 mm including cutting for pinning in ends of brackets or erecting stand, including 32mm bore pvc corrugated waste pipe 900mm long, 32mm bore waste coupling chromium plated long screwed shank and fly nuts etc., complete all as specified and directed.

Supply and fixing in repair 15mm bore shower rose chromium plated 150 x 150mm alongwith 15mm bore shower arm 195 mm long with bend of 45 degree complete all as specified and directed.

Supply and fixing in repair vitreous china squatting pan, "Orissa pattern" of size 580 mm x 440 mm white with integral foot rest complete including provn of cement concrete bedding and connection to trap, flushing pipe, anti syphonage pipe complete all as specified and as directed by the Engineer–in–Charge.

Supply and fixing in repair vitreous china wash down water closet pan (pedestal pattern) white, incl 'P' or 'S' trap, connection to drain and flush pipe, antisyphonage pipe and including pvc seat cover closed pattern flat bottom, mild steel chromium plated or aluminised hinging device complete and as specified.

Supply and fixing mild steel chromium plated hand shower (health faucet ABS body) suitable for 15mm dia pipe with 8 mm dia 1.25 mtr long flexible tube and ABS wall hook including making connection as in repair , complete, all as specified and as directed.

Supply and fixing 10 litre capacity virgin polypropylene cistern, ISI marked, coloured at low level complete with PVC bend/flush pipe and making all connection including taking down existing high or low level unerviceable flushing cistern and making good the disturbed surface to match with the existing surface, complete all as specified and directred.

Supply and fixing in repair stainless steel grating 100mm dia with or without waste hole complete all as specified and directed.

Supply and fixing in repair for 20mm bore gun–metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

Supply and fixing in repair pvc water closet seat cover, white, closed pattern with flat bottom, mild steel chromium plated or aluminised hinging device complete all as specified and directed.

S & F CP brass wall mixture 3-in-1 system for mixing hot and cold water suitable for 15mm bore pipe complete with 115 mm long bend pipe,connecting legs & wall flange and wall bracket for hand shower as in repair complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing sinks with drainage board made out of stainless steel 1mm thick sheet for kitchen or laboratory with plugs, waste pipe, brass chromium plated coupling and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm with bowl size 410mm x 330mm x 160mm as in repair, complete, all as specified and as directed.

Supply and fixing as in repair brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and as directed by the Engineer–in–Charge.

Supply and fixing in repair 32 mm dia PVC waste pipe for wash hand basin /kitchen sink etc of standard length complete all as specified and as directed by the Engineer–in–Charge.

Supply and fixing as in repair 20mm bore GI unions to connecting galvanised iron pipe complete all as specified and as directed.

Supply and fixing in repair 20mm bore ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed.

Supply and fixing in repair 32/40mm bore CP waste coupling full threaded suitable for kitchen sink etc of standard length complete all as specified and as directed by the Engineer–in–Charge.

Taking down chowkats or frames with shutter area not exceeding 1.50 Square meter (without taking off shutters from the frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish , complete, all as specified and as directed.

Taking down chowkats or frames with shutter area exceeding 1.50 Square meter and not exceeding 4.00 Square meter (without taking off shutters from the frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish, complete, all as specified and as directed.

Taking down shutters of any description area exc 1 sqm and not exc 2 sqm and removing from site , complete, all as specified and as directed.

Taking down shutters of any description area exc 1 sqm and not exc 2 sqm each and refixing in the same opening, complete, all as specified and as directed.

Supply and fixing bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook and pintle hinges; large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe 410-0 or Fe 310-0 complete all as specified and as directed by the Engineer-in-Charge

Cutting holes in brick walls built in cement mortar exceeeding half brick thick and not exceeding one brick thick wall for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 (Depth of embedded portion of holdfasts or lugs measured from the face of the jamb into the wall)as required, complete all as specified and as directed by Engr-in-charge.

Supply and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, all as per direction of Engineer-in-Charge. (Note: stainless steel butt hinges and necessary SS screws shall be paid separately) complete all as specified and as directed by the Engr–in–charge.

Supply and fixing double shutter steel window box type ERW hollow P section comprising of glazed/gauged skeleton shutter fabricated from following sections :- (a) ERW hollow P section frame of size 60 mm x25 mm made from 1.25 mm thick MS sheet (02 Nos i.e. 01 for glazed shutter and 01 for gauzed shutter ). Both P section shall be welded with flat iron 25x03 mm thick all around of frame on both inner and outer faces . (b) Style and rails of window shutters shall be fabricated with ERW hollow P section of size 50 mm x25 mm made from 1.00 mm thick MS sheet and comprising of 02 Nos sash bars for glazed window leaf of T – section 20 x 03 mm thick and one No sash bar of 20 mm x 3 mm thick section for gauzed winodw leaf . (c) Vertical mullion shall be ERW hollow T -section of size 60 x 25 mm made from 1.25 mm thick MS sheet (d) The above steel window shall be deemed to include the following accessories/ fittings : i) Hold fast 150mm long mild steel flat iron 12x3 mm thick made to shape- 04 Nos per window ii) Handle of Z section 20mmx25mm, 100mm long – 01 No per leaf. iii) MS tower bolt stove enamelled 150mm long- 2 Nos per leaf. iv) Z section 20mmx25mm, 100mm long stopper – 01 No per leaf. (v) Cleat 55 mm long of solid square 15x20x.63mm square - 01 No per leaf (vi) Pintal hinges 12 x 75 mm - 2 Nos each leaf (vii) 10mm square Guard bar @ 10 cm c/c welded to frame . (viii) Two coat of Synthetic enamel paint over one coat of red oxide primer. (ix) 0.36mm nominal dia of stainless steel wire mesh and average width of aperture of 1.40mm fixed in gauzed skelton shutter of window with flat iron 15 x 03 mm with steel screws . (x) 3mm thick sheet glass, ordinary quality and with oil putty in square n. exc 0.5 sqm in each pane fixed in glass shutter of window. (xi) Fabrication and fixing arrangements as per specification including cutting holes and making good dismantled portion in PCC 1:2:4 type B-1 /cement plaster 1:4 as require and make finish good to the existing surface complete all as specified and directed. Notes : (i) For the purpose of measurement and payment double shutter both glazed and gauzed with frames shall be considered as one unit. (ii) Unit rate quoted against this item shall also include the iron mongery, grill and other accessoriries as mentioned above. (iii) The window upto 1.00 metre width shall consists of two leaves both for gauzed shutter and glazed shutter and all the shutters are openable. The window more than 1.00 metre width shall have two openable leaves on both outer side for gauzed shutter and glazed shutter and middle leaf/shutter shall be fixed type.

Supply and fixing powder coated aluminium section (minimum thickness of powder coating 50 micron) for doors,windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/panelling, C.P. brass/ stainless steel screws complete all as specified and as directed by the Engineer-in-Charge. Note : (a). Glazing shall be measured and paid separately; (b). Weight of aluminium sections shall be as per IS or actual weight which ever less shall be measured. (c). The rates quoted shall be inclusive of neoprene beading, glazing clips, jointing clips, screws, etc as required and the same shall not be measured for arriving the weight; (d). The rates shall be inclusive of locking arrangement including complete packing with silicon gel all around contacting surface of aluminium framework and including matching the existing surface area complete all as specified and directed.

Supply and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other frames/ chowkhat of size 50 x 70 mm comprising of virgin PVC polymer of K value 58–60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant complete all as specified and directed.

Supply and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other frames/ chowkhat of size 65 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant complete all as specified and directed.

S&F factory made single extruded WPC (Wood Polymer Composite) glazed and skeleton shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, all as per direction of Engineer-in-Charge. (Note: stainless steel butt hinges and necessary SS screws shall be paid separately) complete all as specified and as directed by the Engr–in–charge.

Material and labour for PCC 1:3:6, type C–0 (12.50mm graded crushed stone aggregate) as in bed blocks for hold fast & filling of pressed steel frame including necesssary formwork complete all as specified and directed.

Supply and fixing for 100mm stainless steel Butt hinge medium weight cold rolled, complete all as specified and directed.

Supply and fixing for 150mm long aluminium, anodised, barrel tower bolt of extruded section, complete all as specified and directed.

Supply and fixing for 100mm long aluminium, anodised, barrel tower bolt of extruded section, complete all as specified and directed.

Supply and fixing for 150mm long aluminium handles, fabricated type, anodised complete, all as specified and directed.

Supply and fixing in repair floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor 150mm long cover plate, complete all as specified and directed.

Supply and fixing 300 mm long aluminium sliding door bolts, plate type, stove enamelled black with bright bolt not less than 12 mm dia with and including minimum of 6 bolts and nuts, four on bolt plate and two on staple and fixed complete all as specified and directed.

Supply and fixing mild steel 150 mm, ordinary rat tail rod pattern springs, including roller and roller plate including fixing to steel frame complete all as specified and directed.

Supply and fixing in repair for 150mm long aluminium handles, cast type, anodised complete all as specified and directed.

Supply and fixing in repair for 100mm MS Butt hinge medium weight, cold rolled and welding to MS chowkhats if reqd complete all as specified and directed.

Supply and fixing in repair for 150mm long aluminium, anodised, barrel tower bolt of extruded section, complete all as specified and directed.

Supply and fixing in repair 300 mm long aluminium sliding door bolts, plate type, stove enamelled black with bright bolt not less than 12 mm dia with and including minimum of 6 bolts and nuts, four on bolt plate and two on staple and fixed complete all as specified and directed.

Material and labour welding to grills, guard bars, steel windows, fixing of hinges to steel chowkhats and steel door etc., thickness of metal to be welded exc 6mm and not exceeding 9 mm and exceeding 2.5 cm and not exceeding 5.0 cm in length complete all as specified and as directed.

Demolition of brick work built in cement mortar or cement lime mortar including all quoins, arches, pillar etc but excluding ashlar facing, dressed stone work and precast concrete articles , complete, all as specified and as directed.

Material and labour brick work with sub class 'B' old size bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6, up to height of double storey bldg, including necessary scaffolding /formwork etc complete all as specified and as directed.

All as per serial item No. 79 here in befor but except bricks (old serviceable bricks obtained from serial item No 78 above including removing motar, cleaning the bricks with water,shall be used), complete all as specified and as directed by the Engineer-in-Charge.

Demolition of cement concrete (reinforced) in roofs, floors (other than ground floors) beams, slabs, staircases, landing, chajjas and similar suspended work including cutting of steel reinforcement as required to facilitate demolition and removal the rubbish/ demolished material outside defence land, complete all as specified and as directed by the Engineer–in–Charge.

Material and labour for reinforced cement concrete (Nom mix) type B–1, 1:2:4 (20mm graded crushed stone aggregate) in chajjas and incl necessary formwork /scaffolding upto 9mtr height complete all as specified and directed

Material and labour reinforced cement concrete 1:1–1/2:3 (Nominal Mix) using 20mm graded crushed stone aggregates as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like and incl necessary formwork complete all as specified and as directed by the Engineer–in–Charge.

Supply and fixing mild steel TMT bar 10 mm dia and over cut to length bent to shape required including cranking bending spirally for hopping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0,.9mm dia or screwing with clip etc all as specified.

Hacking out old broken glass (any thickness, size, quality or description) from metal frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed

Supply and fixing 3mm thick sheet glass ordinary quality with aluminium beading, rubber packing or oil putty in square n.exc 0.5sqm in each pane, complete , all as specified and directed.

Supply and fixing 3mm thick frosted sheet glass ordinary type and glazing with aluminium beading, rubber packing or oil putty in square n exc 0.5 sqm each pane complete all as specified and directed.

Supply and fixing for galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with stainless steel wire staples, complete all as specified and directed.

Supply and fixing in repair galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with stainless steel wire staples or ms nut & bolt including removing from old steel window /door cutter /grinder or any other method complete all as specified and directed.

Supply and fixing in repair stainless steel rod of 25 mm dia, min 1.0 mm wall thickness as in curtain rod complete incl Supply and fixing 02 Nos stainless steel brackets/finials fancy type, stops fixed with ss screws etc complete fixed as in repair complete all as specified and as directed by the Engineer–in–Charge. Note : For the purpose of mesurement and payment running length of curtain rod only shall be considered.

Taking down of PVC /cast iron/RCC drain pipes /rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan–necks, etc., including where as necessary excavation, returning filling, removal etc and cleaning or refixing or removal to store, jointed in cement mortar and taking out of trenches, if required complete all as specified and directed.

Supply and fixing 110mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joints, fixed on wall including all fittings (branch piece,tee & coupler etc ) complete all as specified and directed.

Supply and fixing 110mm bore PVC (SWR) bends of any radius , complete, all as specified and as directed.

Supply and fixing 75mm bore PVC (SWR) pipes single socketed incl all necessary fitting tee ,branch piece, single Y etc. in any length with rubber ring joints, laid in floor /trenches complete all as specified and as directed by the Engineer–in–Charge

Supply and fixing 75mm bore PVC (SWR) bends of any radius , complete, all as specified and as directed.

Supply and fixing in repair 75 mm PVC(SWR) floor trap with grating incl jointing to waste pipe incl fixed in cement concrete type B–1 (1:2:4) complete all as specified and as directed.

Supply and fixing continuous (piano) hinges, width of flaps 30mm (when open) mild steel bright finish or electro galvanished complete all as specified and as directed by the Engr–in–charge.

Supply and fixing for 100mm long aluminium handles, fabricated type, anodised complete, all as specified and directed.

Supply and fixing 100 mm long hasp and staple, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws complete all as specified and directed.

Material and labour for PCC 1:5:10 type E–2 using 40mm graded crushed stone aggrgate as in filling in sunken portion floor, rounded or chamfered on edges including demolition of old PCC and removing from site complete all as specified and directed.

Dismantling Brick tiles or terracing tiles, single layer on roofs complete all as specified and as directed by the Engineer-in-Charge.

Demolition of mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof) complete all as specified and as directed by the Engineer-in-Charge.

Material and labour providing cement concrete (1:2:4) type B1, using 20mm graded stone aggregate as in roof kerbs, mud stops, padding etc., and finished even and smooth without using extra cement including form work where ever required complete all as specified and as directed by the Engineer-in-Charge.

Material & Labour for providing and laying 3mm thick APP (atactic polypropylene polymer) modified prefabricated five layer weight not less than 3.60 kg /Sqm water proofing membrane black finish reinforced with non woven polyster matt and consisting of a coat bituminous primer @ 0.40 litre /Sqm by the same membrane manufactures of density 0.87 to 0.89 kg/ltr at 25 degree centegrate temperature and viscosity 70–160 cps over the primer coat with overlap of 100mm at the side and 150mm at the end, the layer membrane shall be laid using butane gas torch and sealing all joints etc. after preparing the surface complete as per standred practice as per manufacture's instructions. The vital physical and chemical parameters of the membrane shell be under :– (i) Joint strength in longitudinal and transverse direction at 23 degree centegrate at 650/ 450 N /5 cms. (ii) Tear strength in longitudinal and transverse direction at 300/250N/5 cms. Softing point of membrane not less then 150 degree centegrate when tested in accordance with ASTM (d–5147) (iii) The laying of membrane shell be got down through the authorised applicator of manufactures of membrane only, complete all as specified and as directed. (iv) The work shall be carriout at a height upto 12 metre.

Material and labour cement concrete tiles 30 cm x 30cm x 20 mm thick, machine pressed laid on screed bed and joints grouted flush in CM (1:3) mixed with 5% crude oil by weight of cement including screed bed 15 mm thick in cement mortar 1:6 complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for sunken floor water proofing treatment complete all as under :– (A) Scrapping the surface with wire brush and cleaning with water and allow to dry. (B) Applying cement slurry @ 3 kg/sqm duly mixed with water proofing compound. (C) 15 mm thick cement plaster 1:3 mixed with water proofing compound as per manufacture instruction (the corner will made rounded in concave shape). (D) Apply one coat of hot bitumin grade 85/25 conforming to IS 702 @ 1.5 kg/sqm. (E) Supply and laying APP with non woven polyster reinforced sheet 3mm thick weight not less than 3.00 kg/sqm. (F) Applying one coat of hot blown bitumin grade 85/25 conforming to IS–702 @1.50 kg/sqm. (G) Curing the sunken portion with water min 48 hours by ponding. (H) Fixing 50mm bore GI pipe medium grade as in spout of 0.60 mtr length in each sunken.

Supply and fixing of 18mm thick PVC sheet (density not less than 600 Cum) having one side decorative laminated sheet all required brackets SS screws etc. the panel shall be fabricated using adhesive and screws where ever required.all the edges shall be covered with 2mm thick edge bonding tape or 90 degree edge bent finish as per make and specification including dismanteling existing board any type complete all as specified and directed. NOTE: - Material manufacture test certificate alongwith purchase voucher should be produced before execution of work.

Supply and fixing in repair 15 mm bore spindle for Bib Tap /Angle Cock /concealed stop cock etc of standard length complete all as specified and as directed by the Engineer–in–Charge.

Supply and fixing in repair pvc flushing cistern internal fittings complete (syphone, lever, ball float valve and rubber washer or gasket etc) of 10 ltr capacity complete all as specified and directed.

Supply and fixing as in repair PVC tank lid/cover suitable for capacity 500 /1000 ltrs with and including locking arrangments such as nuts, bolts etc complete all as specified and as directed by the Engineer–in–Charge.

Supply and fixing in repair stainless steel kitchen plate rack made out of 0.63mm thick stainless steel of grade SS304 of size not less than 786 mm x 914mm x 264mm, including screws and fixing arrangements complete all as specified and directed.

Supply and fixing in repair glass corner shelf 8mm thick including CP railing radius 200mm complete all as specified and directed by Engineer–in–Charge.

Supply and fixing as in repair mild steel door shutter two leaves with frame of 20 gauge MS sheet (all around) and leaves of 21 gauge MS Sheet (all as per godrej pattern) with three way locking arrangement with brass lock with duplicate key and CP handle including two coats of spray painting over a coat or red oxide primer complete fixed in existing cupboard fixed with necessary nuts, bolts including embedded in PCC 1:2:4 (area of opening shall be measured) complete all as specified and as directed by the Engineer–in–Charge.

Material and labour for cleaning of sewage line upto first man holes by any means and removing blockage of WC, EWC, Bathroom, floor trap of WHB/Kitchen pipe etc including first man hole complete all as specified and as directed by the Engineer–in–Charge.

Material and labour for cleaning of manhole or gully trap of any size, type and any depth and removing the sludge /solid content from the manhole or pit by manual /mechanical method or any other suitable means at the discretion of the contractor at his own arrangements including flushing with fresh water and make the manhole or pit fully functional to the entire satisfaction of Engineer-in-Charge also to remove the sludge/solid contents out of defence land including covering with a layer of lime and further earth filling and respositioning of the RCC /CI cover slab all as directed by the Engineer-in-Charge.

Note for Item No. 114 to 115 :– (i) Contractor or his authorised rep will report daily at 0830 hrs and onwards at complaint cell for collection of complaints from the concerned JE's in charge and distribute all complaints/ detailing to his tradesmen, monitoring the work done and taking the complaint slip back from trademans on every working day, re–submit the same to JE's in charge after rectifying the complaint at complaint cell, failing which a recovery of Rs 1000/– per day shall immediately be effected from the contractor's dues in terms of conditions 25, 44 & 45 of IAFW–2249 (General Conditions of contracts). (ii) The complaint shall be attended & defect shall be rectified within 08 hrs i.e from 0900 hrs to 1700 hrs (excluding sunday & gazetted holiday), commencing from date and time of notifying the complaint slip failing which a penalty @ Rs.120/– per complaint per day (08 hrs) shall be levied upon/imposed on the contractor and necessary recovery shall be effected from his dues on this account. In case, after checking & attending the defects, if it is not possible to rectify the defect within 08 hrs, the fact shall be brought to the notice of Engr–in–Charge by the contractor/ his rep immediately and if Engineer–in–Charge is satisfied with the facts brought by the contractor, no recovery shall be made on this account. (iii) All T&P required for attending the complaints shall be provided by the contractor without any extra. (iv) The mason shall always be in possession of all mason tools like trowel, plumb, hammer, chisel etc. as required at site or will be arrange by contractor on site on own expenditure and deemed to be included uin quoted rates. (v) The above all aspect shall be deemed to be included in the quoted rate of the respective item. (vi) All the complaint slip, register & other connected documents will be provided and maintained by contractor. (vii) Proper record (date wise) of complaints received & rectified by the contractor and attendance register of tradesman shall be maintained and may be asked for the verification at the time of payment of each RAR/Bill.

Note:- Amount of credit of Rs.85,035.00 for retrieved materials is mentioned in Schedule of Credit Page No. 111 & 112 of tender documents in pdf form which will be deducted offline while acceptance of tender.

dhingra builders (BID ID -3375802)

MAYANK ENTERPRISES (BID ID -3367574)

Peerzada And Sons (BID ID -3367647)

shiv const co (BID ID -3365746)