Providing LWSS to PC habitations Charna Dana Ghaton Ganog Jammu Koti Jarag Koti Dhiman Maina Gharel and Rajana under JJM GP Dadahu in Tehsil Sangrah Distt. Sirmour HP

Amount

Excavation in foundation and trenches etc.(in pipes and pits) in all kinds of soils such as pick work, jumper work, blasting in soft/hard rock, chiselling/wedging out of rock/where blasting prohibited) saturated soil stacking the excavated soil as directed by the Engineer-in-charge clear from the edge of excavation and then returning the stacked soil in 15cm layers when required into plinth sides of foundation etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed by the Engineer –in-charge in all leads and lifts.

Providing and laying cement concrete 1:6:12 (1Cement:6sand:12 graded stone aggregate 40mm nominal size) and curing complete excluding the cost of form work foundation and plinth in all leads and lifts

Brick work using common burnt clay building bricks (IInd class) in super structure above plinth level upto floor two level in cement mortar 1:6 (1cement:6 sand) in all leads and lifts. and carriage of material and as per direction of Engineer incharge

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike?plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: Profile B Fixing with adjustable lugs with split end tail to each jamb

Providing and fixing 1 mm thick M.S sheet garrage door with frame of 40 mmX 40mm X6mm angle iron 3.15 mm m.s gusset plates at the junctions and corners,all necessary fittings complete including applying a priming coat of red lead paint. Using M.S angles 40mm x 40mm x 6mm for diaganal braces in all respect and as per direction of Engineer Incharge.

Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm, so as to give a fair finish including centring, shuttering , strutting and propping etc. with wooden battens and ballies height of propping and centering below supporting floor to ceiling not exceeding 4meters and removal of the same for insitu reinforced concrete and plain.

a )Flat surfaces such as soffits of suspended floors, roofs, landings and the like floors upto 200mm kin thickness.

b) Vertical surface such as walls (any thickness) partition and the like I/c attached pillasters, buttresses, plinth and string sourses and the lick

c) Edeges of slab

Providing and laying cement concrete work 1:2:4(1cement:2sand: 4 graded stone aggregate 20mm nominal size ) and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in:-

Suspended floors, roofs, landings and shelves and their supports, balconies, beams ,griders bressumers and cantilevers upto all floor level.

Cement concrete flooring 1:2:4(1cement:2sand:4 graded stone aggregate 20mm nominal size) laid in one layer finished with a floating coat of neat cement (40mm thick) in all leads and lifts.

20 mm cement plaster in single coat on rough side of brick /stone masonary for interior plastering upto floor two level including arrises, internal rounded angles,chamfers and/or rounded angles not exceeding 80-mm in girth and finished even and smooth in cement mortar 1:6(1cement:6app.sand) including all leads, lifts and carriage of material at site and as directed by the Engineer Incharge.

6mm cement plaster in ceiling in cement mortar 1:3 (1cement:3sand) including all leads lifts and carriage of material at site and as directed by the Engineer Incharge.

Providing plinth protection 50mm thick in cement concrete 1:3:6) 1cement : 3sand : 6graded stone agg. 20mm nominal size) including finishing the top surface of concrete smooth including all leads, lifts and carriage of material at site and as directed by the Engineer Incharge.

Providing mild/tor steel reinforcement for R.C.C. work including bending and binding and placing in position complete up to floor two level including all leads,lifts and carriage of material at site and as directed by the Engineer in Charge.

Painting two coats (excluding priming coat)on new steel and other metal surface under coat with ready mixed paint brusing to give an even shade including cleaning the surface all dirt,dust and other foreign matter :-- With readymixed paint other than white in all leads and lifts. as per direction of Engineer incharge

Applying priming coat over new steel and metal based surface after and including preparing the surface by thoroughly cleaning oil dirt grease and other foreign matter sand papering and knotting ready mixed paint brushing primer pink in all leads and lifts. as per direction of Engineer incharge

Finishing wall with water proofing cement paint of approved brand & manufacture & of required shade on undecorated wall surfaces (two coats) to give an even shade after thotoughly brushing the surface to remove all dirt & remains of loose powdered materials. in all leads and lifts. and as per the direction of Engineer incharge.

Providing and fixing following anodized aluminium fittings of anodized transparent and shade with necessary screw etc.complete in all respect

(a) Sliding door bolts 250x16mm.

(b-i) M.S. tower bolts (Barrel type) 200x10mm.

(b-ii) M.S. tower bolts (Barrel type) 150x10mm.

(b-iii) M.S. tower bolts (Barrel type) 100x10mm.

(c-i) M.S. handles 125 mm dia

(c-ii) M.S. handles 75 mm dia

Demolition above G.L. up to floor two level including disposal of unserviceable materials with in 20 mtr lead and I/c cutting the necessary rienforcement and separating out from R.C.C. work.

Demolition below G.L. up to 1.50 mtrs depth and disposal of unserviceable materials with in 20 mtr lead unreinforced cement concrete more then 15cm thickness. I/c all leads , lifts and carrige of material at site and as directed by the Engineer Incharge.

Dimantling doors,windowos and clearstory windows,ventilators etc. (wood or steel) shutters I/c chowkhats, architravas,holdfasts and other attachments etc. complete and stacking them with 20mtrs lead not exceeding 3sqm. In area.including all leads , lifts and carrige of material at site and as directed by the Engineer Incharge.

Demolition above G.L. up to floor two level including of unserviceable materials with in 20 mtr lead un-reinforced cement concrete more then 15cm thickness. I/c all leads , lifts and carrige of material at site and as directed by the Engineer Incharge.

Applying one coat of distemper primer of approved brand and manufacture on wall surfaces after thoroughly brushing the surface free from mortar dropping and other foreign matter and including preparing the surface even and sand papered smooth as directed by the Engineer Incharge.

Distempring (two coats) with oil bound washable distemper of approved brand and manufacture and of requried shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar dropping and other foreign matter and also including preparing the surface even and sand papered smooth. Priming coat with distemper primer as directed by the Engineer Incharge.

Providing and fixing M.S hooks and eyes 100mm including all leads , lifts and carrige of material at site and as directed by the Engineer Incharge.

Constructing course rubble hammer dressed ' U ' shape open surface drain with side walls 15 x 22 cms. in cement mortor 1 : 6 (1 cement : 6 sand ) and inside plastering with cement plaster in cement mortor 1 : 3 (1 cement : 3 sand ) including earth work and laying 10 cms.cement concrete in 1 : 5 : 10 ( 1 cement : 5 sand : 10 graded stone aggregate of 40 mm nominal size and 7.5 cms. cement concrete 1 : 2 : 4 ( 1 cement : 2 sand : 4 graded stone aggregate of 20 mm nominal size ) and finished with a floating coat of neat cement complete as per standard design. including all leads , lifts and carrige of material at site and as directed by the Engineer Incharge.

Providing and fixing M.S. fan light pivote with necessary screw etc. complete including all leads , lifts and carrige of material at site and as directed by the Engineer Incharge.

Providing and fixing PVC Pipe 80 mm dia from P or s trap to septic tank & vent. in septic tank including all leads ,lifts and carrige of material at as directed by the Engineer Incharge.

Terrazzo tile flooring with precast terrazzo tiles 20 mm thick with marble chips of specified size laid in floors,treads of steps and landing on a bed of 25 mm average thickness of cemenrt mortar 1 :6 ( 1 cement,6 sand ) jointed with neat cement slurry mixed with pigment to match the shade of tile where ever required including rubbing and polishing complete with tiles of following shades medium with in all leads and lifts complete in all respect.

Wiring of light point / fan/ exhaust fan point call bell point with 1.5 sq mm PVC insulated copper conductor cable in surface/ recessed PVC condurce required (Group C) Complete with all lead and lift.

Wiring for cicuit wiring with 1.5 Sq mm PVC insulator copper conductor single coil cable om surface recessed PVC conduct required . Complete with all lead and lift Finolex make.

Wiring for light/ power plug wiring with 2.5 Sq mm . PVC insulated copper conductor cable in surface recessed PCV conduit allow with 1 No. 2.24 mm dia base copper conductor wire for loopearthing. Complete with all lead and lift Finolex make.

Suppling , Fixing of 15/16 Amp .3 pin tumpler , Piano type switch socket complete on existing box cover including connection etc as required compelete with all leads and lift. Havells Make, Finolex Make.

Suppling , Fixing of 5/6 Amp .3 pin switch socket and Switch outlet on the existing switch box cover including connection etc as required compelete with all leads and lift. Havells Make,

Suppling fixing wooden box of following six nominal on surface racess with suitable sixe of phonetic laminated sheet cover in from as required.

(i) 8"x6" or 203 mm x152 mm

(ii) 4"x7" or 102 mm X178 mm

Wiring for sub main wiring with 4 Sq m PCV insulated copper conduction in single cover in surface or recessed in PVC conduction required with all lead and lift

Supplying , fixing 5 to 32 Amp rating 240 volts L- Series main circuit bracker in existing MCB box. Complete with commissioining connection testing etc. as required with all lead and lift Havells Make.

Single Pole

Supplying , fixing 40 to 63 Amp rating 240 volts L- Series main circuit bracker in existing MCB box. Complete with commissioining connection testing etc. as required with all lead and lift Havells Make.

Double Pole

Supplying , Fixing single pole and natural sheet steel MCB distribution box on surface/ recessed complete with tinned copper busher, neutral, detachable , glass plate inter connection including painting earthing etc. 4 way complete with all lead and lift, Havells MAKE.

Providing installing testing and commissioning of electronic tube fitting complete suitable to operate on 230 volts single phase AC supply directly on surface with copper wiring as required. Havells Make.

S/F Backlite batten/ angle holder including connection etc. complete with all lead and lift. Havells make

S/F ceiling rose on existing junction box/ wooden block including connection as required complete with all lead and lift. Havells make

Providing installing testing and commissioning of ceiling fan with regulator including wiring the down rod of standred length (upto 30 cm _) with 1.5 mm PVC insulated copper conductor single core cable as required 1200 mm sweep Bajaj/ Uska Make.

Providing and fixing C.P.brass waste for wash basin 32mm dia, including all lead lifts and carriage of material at site and as directed by the Engineer Incharge

P/F G.I. elbow,tee, socket, union, plug, nipple 7 Gate valve heavy grade of following dia reputed make,i/c all lead lifts and carriage of material at site and as directed by the Engineer Incharge

Elbow 15mm dia

Tee 15x15x15 mm dia

Socket 15mm dia

Union 15mm dia

Plug 15mm dia

Nipple 15mm dia

Gate valve 15mm dia

C.I. Clamp 65x15

Laying and jointing in trenches galvanised mild steel tube for In Let , Out Let and Scour pipe (light grade) tube fitting (earth work to be measured and paid for seperately) including all leads, lifts and carriage of material at site and as directed by the Engineer Inchargte.

15 mm dia (L)

Providing and laying double socket C.I. bends 80 mm dia of 45˚ heavy duty , i/c all lead lifts and carriage of material at site and as directed by the Engineer Incharge

Providing and laying double socket C.I. bends 80 mm dia of 22˚ -30' heavy duty , i/c all lead lifts and carriage of material at site and as directed by the Engineer Incharge

Providing and fixing CI L-bend of reputed make, including all lead, lifts and carriage of material at site and as directed by the Engineer Incharge.

Providing and fixing T-ring of reputed make, including all lead, lifts and carriage of material at site and as directed by the Engineer Incharge.

Providing and fixing hole basin mixture of reputed make, including all leads, lifts and carriage of material at site and as directed by the Enginer incharge.

Providing and fixing Kitchen sink mixture of reputed make, including all leads, lifts and carriage of material at site and as directed by the Enginer incharge.

Providing and fixing b cock long body of reputed make heavy duty , including all leads, lfits and carriage of matrial at site and as directed by the Enginer Incharge.

Providing and fixing PVC Storage tank 1000 ltr cap. make heavy duty , including all leads, lfits and carriage of matrial at site and as directed by the Enginer Incharge.

Chaman Lal Contractor

Deepak Kumar Contractor