PROVISION OF STANDBY POWER SUPPLY TO PERIMETER LIGHT AND WATCH TOWER AT AF STN BAREILLY

Amount

Excavation in trenches in Soft/Loose soil not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth and getting out all as required for laying of cables, foundation filling of poles or stays all as specified and directed.

Returning, filling in including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick all as specified and directed.

Removing excavated material (Soil) to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point all as specified and directed.

M&L for Dry sand cushioning for protection of under ground cables (8cm before laying the cable and 15cm after laying the cable in trenches and punning down upto 18 cm) complete, all as specified and directed.

M&L for Well burnt Sub class 'B', Old size bricks laid dry, flat, over the cable abutting each other, length of brick equal to width of brick, complete all as specified and directed.

Supply and laying/fixing GI tubing light grade with all fittings and fixed complete to walls, poles and laid in floors,in trenches & under road for cable protection of size 100mm dia all as specified and directed.

Supply and laying/fixing GI tubing light grade with all fittings and fixed complete to walls, poles and laid in floors,in trenches & under road for cable protection of size 80mm dia all as specified and directed.

Supply and laying/fixing GI tubing light grade with all fittings and fixed complete to walls, poles and laid in floors,in trenches & under road for cable protection of size 50mm dia all as specified and directed.

Supply and laying/fixing GI tubing light grade with all fittings and fixed complete to walls, poles and laid in floors,in trenches & under road for cable protection of size 40mm dia all as specified and directed.

M & L for horizontal boring under Road, pavement, hard standing complete with inserting GI pipe light grade of size 50/80mm dia all as specified and directed. Note :- GI pipe shall be measured and paid seperately.

Supply, laying & testing of LT Cable XLPE insulated, galvanized steel strip or wire armoured, electric power cables (heavy duty) with stranded aluminium conductor, 1100 volts, grade cross setional area 95 Sqmm 3.5 Core complete all as specified and as directed.

Supply, laying & testing of LT Cable XLPE insulated, galvanized steel strip or wire armoured, electric power cables (heavy duty) with stranded aluminium conductor, 1100 volts, grade cross setional area 70 Sqmm 3.5 Core complete all as specified and as directed.

Supply, laying & testing of LT Cable XLPE insulated, galvanized steel strip or wire armoured, electric power cables (heavy duty) with stranded aluminium conductor, 1100 volts, grade cross setional area 50 Sqmm 3.5 Core complete all as specified and as directed.

Supply, laying & testing of LT Cable XLPE insulated, galvanized steel strip or wire armoured, electric power cables (heavy duty) with stranded aluminium conductor, 1100 volts, grade cross setional area 35 Sqmm 3.5 Core complete all as specified and as directed.

Supply, laying & testing of LT Cable XLPE insulated, galvanized steel strip or wire armoured, electric power cables (heavy duty) with stranded aluminium conductor, 1100 volts, grade cross setional area 25 Sqmm 4 Core complete all as specified and as directed.

Supply, laying & testing of LT Cable XLPE insulated, galvanized steel strip or wire armoured, electric power cables (heavy duty) with stranded aluminium conductor, 1100 volts, grade cross setional area 16 Sqmm 4 Core complete all as specified and as directed.

Design, supply, erection, testing and commissioning of outdoor type LT Feeder Pillar of overall size not less than 1050mm width x 800mm Height (Without Canopy & Base Channel) x 400mm Depth, M.S. Channel Base Frame mounted (to be mounted on the 3 side covered brick. pedestal of height 900mm above ground level) , suitable for 3 phase 4 wire, 415 volts AC supply and having 4 Nos Aluminium bus bars of rating 100 Amps, Provision of Spreader link to incoming side of MCCBs for termination of cables and 4 way ebonite cable connector (rating 32 amps) for termination of outgoing cables with MCBs.TheFeeder Pillar shall be duly fabricated in a approved / certified factory / fabrication house who posseses type test certificate from CPRI for similar type of Feeder Pillar and having modern fabrication and testing facility which includes atleast seven (07) tanks pre-treatment facility comprising of de-greasing, rinsing, de-rusting, rinsing, phosphating, rinsing and passivation followed by powder coated painting (thickness not less than 80 Micron) with approved shade of RAL 7032

(SIEMENS GRAY). The Feeder Pillar shall be provided with suitable rubber gasket to make it completely dust and vermin proof and degree of protection not less than IP-55 and general construction conforming to IS : 13947. The feeder pillar shall be made out of 3.00mm thick CRCA mild steel sheet and 3.00mm thick gland plate and having compartmentalized construction for individual switchgears and Bus Bars and having front opening facility (with double layer shutter) and rear opening facility with single layer shutter with locking facility and 2 side slanting canopy type roof on top and mild steel channel (MC-75) base frame at bottom, suitable for mounting on the brick pedestal through grouting bolt, The panel board shall be provided with ventilation facility in the form of louvers for better heat dissipation. The feeder pillar shall be comprising of the followings :-

Location :- LT Panel Pocket No 1 (PH No 10) & Pocket No 7 (PH No 15) PROVISION FOR CABLE ENTRY :- The provision for cable entry / exit shall be provided in the bottom for both incoming and outgoing cables. BUS BARS & INTERNAL CONNECTIONS :- The bus bars should be made of Aluminium, duly insulated with 1100 volts grade standard colour coded heat shrink type PVC sleeves and rigidly mounted on suitable size 'F' class insulators of non hygroscopic non combustable, track resistant,high strength FRP / SMC / DMC material. 4 Nos Aluminium bus bars of rating 100 Amps, . For all internal connections from main bus bars to switch gears shall be carried out with suitable size FRLS grade PVC insulated multiflexible type copper wire as per the current carrying capacity of individual switch gears. Earthing bar shall be provided as per standard practice and shall be made of Galvanized Steel flats of size 25mm x 6 mm

MISCELLANEOUS ITEMS :- (a) SP MCB 6 Amps 10 KA (For Control Wiring) - 03 No. (b) Danger Notice Plate duly written in Signal Red colour on Aluminium plate in English & Hindi language and of size not less than 150mm x 100mm - 02 Nos Note : 1) All incoming & outgoing feeders to be marked with aluminium name plates duly rivetted on the front inner door of the feeder pillar. 2) All the cable entry / exit will be through bottom only, duly glanded with single compression type brass cable gland of suitable size. Cost of end termination of cable shall deemed to be included in the cost of feeder pillar. 3) All the inner / outer doors should have locking facility through castle locks 4) Cost of all civil work for brick pedestal, duly plastered, shall deemed to be included in the unit rate quoted, no separate payment shall be allowed for this. 5) The dimension of Panel Board as mentioned above is tentative. If it is required to be enhanced to accomodate the switchgears and maintaining the gaps as per IE Rules, it should be enhanced as per requirement without any extra cost to the department. 6)The thickness of MS Sheet for outer shell and canopy shall be of 3.0mm and inner doors and partitions shall be of 2.0 mm 7) The Panel Board should be designed in such a way that adequete workable space is made available inside every compartments. 8) The drawing of the Panel Board shall have to be got approved by Garrison Engineer before starting of fabrication process.

Design, supply, erection, testing and commissioning of outdoor type LT Feeder Pillar of overall size not less than 1050mm width x 800mm Height (Without Canopy & Base Channel) x 400mm Depth, M.S. Channel Base Frame mounted (to be mounted on the 3 side covered brick. pedestal of height 900mm above ground level) , suitable for 3 phase 4 wire, 415 volts AC supply and having 4 Nos Aluminium bus bars of rating 100 Amps, Provision of Spreader link to incoming side of MCCBs for termination of cables and 4 way ebonite cable connector (rating 32 amps) for termination of outgoing cables with MCBs.TheFeeder Pillar shall be duly fabricated in a approved / certified factory / fabrication house who posseses type test certificate from CPRI for similar type of Feeder Pillar and having modern fabrication and testing facility which includes atleast seven (07) tanks pre-treatment facility comprising of de-greasing, rinsing, de-rusting, rinsing, phosphating, rinsing and passivation followed by powder coated painting (thickness not less than 80 Micron) with approved shade of RAL 7032

(SIEMENS GRAY). The Feeder Pillar shall be provided with suitable rubber gasket to make it completely dust and vermin proof and degree of protection not less than IP-55 and general construction conforming to IS : 13947. The feeder pillar shall be made out of 3.00mm thick CRCA mild steel sheet and 3.00mm thick gland plate and having compartmentalized construction for individual switchgears and Bus Bars and having front opening facility (with double layer shutter) and rear opening facility with single layer shutter with locking facility and 2 side slanting canopy type roof on top and mild steel channel (MC-75) base frame at bottom, suitable for mounting on the brick pedestal through grouting bolt, The panel board shall be provided with ventilation facility in the form of louvers for better heat dissipation. The feeder pillar shall be comprising of the followings :-

Location :- LT Panel (Pocket No 2 (WSA) & Pocket No 6 (Philiphit Gate OMQ Area) PROVISION FOR CABLE ENTRY :- The provision for cable entry / exit shall be provided in the bottom for both incoming and outgoing cables. BUS BARS & INTERNAL CONNECTIONS :- The bus bars should be made of Aluminium, duly insulated with 1100 volts grade standard colour coded heat shrink type PVC sleeves and rigidly mounted on suitable size 'F' class insulators of non hygroscopic non combustable, track resistant,high strength FRP / SMC / DMC material. 4 Nos Aluminium bus bars of rating 100 Amps, . For all internal connections from main bus bars to switch gears shall be carried out with suitable size FRLS grade PVC insulated multiflexible type copper wire as per the current carrying capacity of individual switch gears. Earthing bar shall be provided as per standard practice and shall be made of Galvanized Steel flats of size 25mm x 6 mm CONTROL WIRING :- All control wirings shall have to be carried out with 1100 volts rated FRLS grade PVC insulated (Gray Colour) multi-flexible type copper wire of cross sectional area 1.50 Sq mm and shall be properly bunched,tied and dressed, ferrule marked for proper identification and crimped with suitable size & type of tinned copper lugs and shall be wrapped with PVC spring type flexible pipes near the door hinges

Note : 1) All incoming & outgoing feeders to be marked with aluminium name plates duly rivetted on the front inner door of the feeder pillar. 2) All the cable entry / exit will be through bottom only, duly glanded with single compression type brass cable gland of suitable size. Cost of end termination of cable shall deemed to be included in the cost of feeder pillar. 3) All the inner / outer doors should have locking facility through castle locks 4) Cost of all civil work for brick pedestal, duly plastered, shall deemed to be included in the unit rate quoted, no separate payment shall be allowed for this. 5) The dimention of Panel Board as mentioned above is tentative. If it is required to be enhanced to accomodate the switchgears and maintaining the gaps as per IE Rules, it should be enhanced as per requirement without any extra cost to the department. 6)The thickness of MS Sheet for outer shell and canopy shall be of 3.0mm and inner doors and partitions shall be of 2.0 mm 7) The Panel Board should be designed in such a way that adequete workable space is made available inside every compartments. 8) The drawing of the Panel Board shall have to be got approved by Garrison Engineer before starting of fabrication process.

Design, supply, erection, testing and commissioning of outdoor type LT Feeder Pillar of overall size not less than 1050mm width x 800mm Height (Without Canopy & Base Channel) x 400mm Depth, M.S. Channel Base Frame mounted (to be mounted on the 3 side covered brick. pedestal of height 900mm above ground level) , suitable for 3 phase 4 wire, 415 volts AC supply and having 4 Nos Aluminium bus bars of rating 100 Amps, Provision of Spreader link to incoming side of MCCBs for termination of cables and 4 way ebonite cable connector (rating 32 amps) for termination of outgoing cables with MCBs.TheFeeder Pillar shall be duly fabricated in a approved / certified factory / fabrication house who posseses type test certificate from CPRI for similar type of Feeder Pillar and having modern fabrication and testing facility which includes atleast seven (07) tanks pre-treatment facility comprising of de-greasing, rinsing, de-rusting, rinsing, phosphating, rinsing and passivation followed by powder coated painting (thickness not less than 80 Micron) with approved shade of RAL 7032

(SIEMENS GRAY). The Feeder Pillar shall be provided with suitable rubber gasket to make it completely dust and vermin proof and degree of protection not less than IP-55 and general construction conforming to IS : 13947. The feeder pillar shall be made out of 3.00mm thick CRCA mild steel sheet and 3.00mm thick gland plate and having compartmentalized construction for individual switchgears and Bus Bars and having front opening facility (with double layer shutter) and rear opening facility with single layer shutter with locking facility and 2 side slanting canopy type roof on top and mild steel channel (MC-75) base frame at bottom, suitable for mounting on the brick pedestal through grouting bolt, The panel board shall be provided with ventilation facility in the form of louvers for better heat dissipation. The feeder pillar shall be comprising of the followings :-

Location :- LT Panel (Pocket No 4 (WT No 17 (Base Ops)) & Pocket No 5 (Arjun Auditorium) PROVISION FOR CABLE ENTRY :- The provision for cable entry / exit shall be provided in the bottom for both incoming and outgoing cables. BUS BARS & INTERNAL CONNECTIONS :- The bus bars should be made of Aluminium, duly insulated with 1100 volts grade standard colour coded heat shrink type PVC sleeves and rigidly mounted on suitable size 'F' class insulators of non hygroscopic non combustable, track resistant,high strength FRP / SMC / DMC material. 4 Nos Aluminium bus bars of rating 100 Amps, . For all internal connections from main bus bars to switch gears shall be carried out with suitable size FRLS grade PVC insulated multiflexible type copper wire as per the current carrying capacity of individual switch gears. Earthing bar shall be provided as per standard practice and shall be made of Galvanized Steel flats of size 25mm x 6 mm

MISCELLANEOUS ITEMS :- (a) SP MCB 6 Amps 10 KA (For Control Wiring) - 03 No. (b) Danger Notice Plate duly written in Signal Red colour on Aluminium plate in English & Hindi language and of size not less than 150mm x 100mm - 02 Nos Note : 1) All incoming & outgoing feeders to be marked with aluminium name plates duly rivetted on the front inner door of the feeder pillar. 2) All the cable entry / exit will be through bottom only, duly glanded with single compression type brass cable gland of suitable size. Cost of end termination of cable shall deemed to be included in the cost of feeder pillar. 3) All the inner / outer doors should have locking facility through castle locks 4) Cost of all civil work for brick pedestal, duly plastered, shall deemed to be included in the unit rate quoted, no separate payment shall be allowed for this. 5) The dimention of Panel Board as mentioned above is tentative. If it is required to be enhanced to accomodate the switchgears and maintaining the gaps as per IE Rules, it should be enhanced as per requirement without any extra cost to the department. 6)The thickness of MS Sheet for outer shell and canopy shall be of 3.0mm and inner doors and partitions shall be of 2.0 mm 7) The Panel Board should be designed in such a way that adequete workable space is made available inside every compartments. 8) The drawing of the Panel Board shall have to be got approved by Garrison Engineer before starting of fabrication process.

Design, supply, erection, testing and commissioning of outdoor type LT Feeder Pillar of overall size not less than 1050mm width x 800mm Height (Without Canopy & Base Channel) x 400mm Depth, M.S. Channel Base Frame mounted (to be mounted on the 3 side covered brick. pedestal of height 900mm above ground level) , suitable for 3 phase 4 wire, 415 volts AC supply and having 4 Nos Aluminium bus bars of rating 100 Amps, Provision of Spreader link to incoming side of MCCBs for termination of cables and 4 way ebonite cable connector (rating 32 amps) for termination of outgoing cables with MCBs.TheFeeder Pillar shall be duly fabricated in a approved / certified factory / fabrication house who posseses type test certificate from CPRI for similar type of Feeder Pillar and having modern fabrication and testing facility which includes atleast seven (07) tanks pre-treatment facility comprising of de-greasing, rinsing, de-rusting, rinsing, phosphating, rinsing and passivation followed by powder coated painting (thickness not less than 80 Micron) with approved shade of RAL 7032

(SIEMENS GRAY). The Feeder Pillar shall be provided with suitable rubber gasket to make it completely dust and vermin proof and degree of protection not less than IP-55 and general construction conforming to IS : 13947. The feeder pillar shall be made out of 3.00mm thick CRCA mild steel sheet and 3.00mm thick gland plate and having compartmentalized construction for individual switchgears and Bus Bars and having front opening facility (with double layer shutter) and rear opening facility with single layer shutter with locking facility and 2 side slanting canopy type roof on top and mild steel channel (MC-75) base frame at bottom, suitable for mounting on the brick pedestal through grouting bolt, The panel board shall be provided with ventilation facility in the form of louvers for better heat dissipation. The feeder pillar shall be comprising of the followings :- Location :- LT Panel (Pocket No 3 (PH No 5)) PROVISION FOR CABLE ENTRY :- The provision for cable entry / exit shall be provided in the bottom for both incoming and outgoing cables.

BUS BARS & INTERNAL CONNECTIONS :- The bus bars should be made of Aluminium, duly insulated with 1100 volts grade standard colour coded heat shrink type PVC sleeves and rigidly mounted on suitable size 'F' class insulators of non hygroscopic non combustable, track resistant,high strength FRP / SMC / DMC material. 4 Nos Aluminium bus bars of rating 100 Amps, . For all internal connections from main bus bars to switch gears shall be carried out with suitable size FRLS grade PVC insulated multiflexible type copper wire as per the current carrying capacity of individual switch gears. Earthing bar shall be provided as per standard practice and shall be made of Galvanized Steel flats of size 25mm x 6 mm CONTROL WIRING :- All control wirings shall have to be carried out with 1100 volts rated FRLS grade PVC insulated (Gray Colour) multi-flexible type copper wire of cross sectional area 1.50 Sq mm and shall be properly bunched,tied and dressed, ferrule marked for proper identification and crimped with suitable size & type of tinned copper lugs and shall be wrapped with PVC spring type flexible pipes near the door hinges.

Note : 1) All incoming & outgoing feeders to be marked with aluminium name plates duly rivetted on the front inner door of the feeder pillar. 2) All the cable entry / exit will be through bottom only, duly glanded with single compression type brass cable gland of suitable size. Cost of end termination of cable shall deemed to be included in the cost of feeder pillar. 3) All the inner / outer doors should have locking facility through castle locks 4) Cost of all civil work for brick pedestal, duly plastered, shall deemed to be included in the unit rate quoted, no separate payment shall be allowed for this. 5) The dimention of Panel Board as mentioned above is tentative. If it is required to be enhanced to accomodate the switchgears and maintaining the gaps as per IE Rules, it should be enhanced as per requirement without any extra cost to the department. 6)The thickness of MS Sheet for outer shell and canopy shall be of 3.0mm and inner doors and partitions shall be of 2.0 mm 7) The Panel Board should be designed in such a way that adequete workable space is made available inside every compartments. 8) The drawing of the Panel Board shall have to be got approved by Garrison Engineer before starting of fabrication process.

Design, supply, erection, testing and commissioning of outdoor type LT Feeder Pillar of overall size not less than 1050mm width x 800mm Height (Without Canopy & Base Channel) x 400mm Depth, M.S. Channel Base Frame mounted (to be mounted on the 3 side covered brick. pedestal of height 900mm above ground level) , suitable for 3 phase 4 wire, 415 volts AC supply and having 4 Nos Aluminium bus bars of rating 100 Amps, Provision of Spreader link to incoming side of MCCBs for termination of cables and 4 way ebonite cable connector (rating 32 amps) for termination of outgoing cables with MCBs.TheFeeder Pillar shall be duly fabricated in a approved / certified factory / fabrication house who posseses type test certificate from CPRI for similar type of Feeder Pillar and having modern fabrication and testing facility which includes atleast seven (07) tanks pre-treatment facility comprising of de-greasing, rinsing, de-rusting, rinsing, phosphating, rinsing and passivation followed by powder coated painting (thickness not less than 80 Micron) with approved shade of RAL 7032

(SIEMENS GRAY). The Feeder Pillar shall be provided with suitable rubber gasket to make it completely dust and vermin proof and degree of protection not less than IP-55 and general construction conforming to IS : 13947. The feeder pillar shall be made out of 3.00mm thick CRCA mild steel sheet and 3.00mm thick gland plate and having compartmentalized construction for individual switchgears and Bus Bars and having front opening facility (with double layer shutter) and rear opening facility with single layer shutter with locking facility and 2 side slanting canopy type roof on top and mild steel channel (MC-75) base frame at bottom, suitable for mounting on the brick pedestal through grouting bolt, The panel board shall be provided with ventilation facility in the form of louvers for better heat dissipation. The feeder pillar shall be comprising of the followings :- Location :- LT Panel (Pocket No 8 (259 SU Guard Room Gate))

PROVISION FOR CABLE ENTRY :- The provision for cable entry / exit shall be provided in the bottom for both incoming and outgoing cables. BUS BARS & INTERNAL CONNECTIONS :- The bus bars should be made of Aluminium, duly insulated with 1100 volts grade standard colour coded heat shrink type PVC sleeves and rigidly mounted on suitable size 'F' class insulators of non hygroscopic non combustable, track resistant,high strength FRP / SMC / DMC material. 4 Nos Aluminium bus bars of rating 100 Amps, . For all internal connections from main bus bars to switch gears shall be carried out with suitable size FRLS grade PVC insulated multiflexible type copper wire as per the current carrying capacity of individual switch gears. Earthing bar shall be provided as per standard practice and shall be made of Galvanized Steel flats of size 25mm x 6 mm CONTROL WIRING :- All control wirings shall have to be carried out with 1100 volts rated FRLS grade PVC insulated (Gray Colour) multi-flexible type copper wire of cross sectional area 1.50 Sq mm and shall be properly bunched,tied and dressed, ferrule marked for proper identification and crimped with suitable size & type of tinned copper lugs and shall be wrapped with PVC spring type flexible pipes near the door hinges.

Note : 1) All incoming & outgoing feeders to be marked with aluminium name plates duly rivetted on the front inner door of the feeder pillar. 2) All the cable entry / exit will be through bottom only, duly glanded with single compression type brass cable gland of suitable size. Cost of end termination of cable shall deemed to be included in the cost of feeder pillar. 3) All the inner / outer doors should have locking facility through castle locks 4) Cost of all civil work for brick pedestal, duly plastered, shall deemed to be included in the unit rate quoted, no separate payment shall be allowed for this. 5) The dimention of Panel Board as mentioned above is tentative. If it is required to be enhanced to accomodate the switchgears and maintaining the gaps as per IE Rules, it should be enhanced as per requirement without any extra cost to the department. 6)The thickness of MS Sheet for outer shell and canopy shall be of 3.0mm and inner doors and partitions shall be of 2.0 mm 7) The Panel Board should be designed in such a way that adequete workable space is made available inside every compartments. 8) The drawing of the Panel Board shall have to be got approved by Garrison Engineer before starting of fabrication process.

Supplying, installation, commissioning and testing complete Silent Diesel Engine driven Generating Set 1500 RPM of following capacities (or nearest higher rating) , AC volts, 50 C/s, 3 phase , 4 wire, 415 volts , 0.8 PF complete with standard control panel as per OEM's recommendation including integrated powder coated acoustic enclosure as per CPCB year 2020 regulations and duly certified by agencies/labs designated by CPCB for noise level upto 75 dbA at one metre distance etc floor mounted including PCC foundation as per manufacturer's instructions complete all as specified and directed and comprising of the following :-(A) DIESEL ENGINE: Turbo charged Diesel Engine suitable for deliver adequete powe,r for driving the alternator, multi cylinder , vertical type, 4 stroke, water cooled , electric battery start conforming to IS 10001/10002/BS-5514 for continuous running capable of taking 10 % overload for one hour in 12 hours testing period complete and comprising of the following :- (i) Radiator cooling including coolant (ii) Radiator fan with guard (iii) Fly wheel with starter ring (iv) Air cleaner oil bath type (v) Vacuum indicator (vi) Electronic governer class 1A (vii) Exhaust silencer (viii) Fuel filter and fuel hoses (ix) Fuel injection pump (x) Fan and water pump assy (xi) Lub oil filter and Pump

(xii) Oil filter (xiii) Turbo Charger (xiv) Lub oil cooler (xv) Engine maintenance manual with spare part list (xvi) Suitably designed acoustic enclosure as per CPCB norms (xvii) Engine Emergency Stop Switch (xviii) Engine safety shut down system against low lub oil pressure and high water pressure. (xix) Electric battery starting system with battery charging alternator and axial type starter motor including adequate number of high capacity maintenance free lead acid battery 12 volts and suitable Ah as recommended by the OEM including interconnecting cables/leads with terminals complete - 01 set (B) ENGINE INSTRUMENT PANEL: It shall be consisting of the the following :- (i) Starting switch ON/Off (ii) Water temp gauge (iii) Hour meter cum RPM indicator (iv) Lub oil pressure (v) Lub oil temperture (vi) Battery charging meter (vii) Safety alarm against high water temp and low/high lub oil pressure. (C) ALTERNATOR : It shall be self excited, self regulated, drip proof, brush less of continuous operation at the speed of 1500 RPM at 415 volts, 50 HZ three phase four wire system with automatic voltage regulator to ensure high voltage accuracy with ± 1% with class H insulation and SPDP enclosure directly coupled with engine through flexible coupling and conforming to IS -13364 complete - 01 No

(D) BASE FRAME : A Common base frame, fabricated with structural steel, for engine and alternator including adequate number of suitable Dunlop metallastik anti- vibration pads all as per recommendation of the manufacture. ( Note :- (E) FUEL TANK : Fuel tank shall be fabricted out of 2 mm MS sheet of capacity and shall be mounted inside the canopy. Capacity of the tank shall not be less than 8 hrs continuous operation. It should contain fuel level gauge , drain plug, locking arrangement etc with and including pipe connections duly laid as per engineering practice complete. (F) Catalogues :- Operation and maintenance manual book, spare parts list, overhauling manual 03 Set. Warranty Card for covering 02 years maintenance period. Note : a) Cost of suitable size PCC foundtion is deemed to be included in the unit rate quoted by the contractor b) Cost of Fuel (for 12 Hrs testing on various loads as specified in P.S.) and Hire Chargse of artificial load alongwith other testing materials, are deemed to be included in the unit rate quoted. No extra charge shall be paid for this. c) If it is required to extend the exhaust pipe outside the room, it shall be done with additional pipe having same specification of existing exhaust pipe including all jointing materials ,Asbestos rope duly bandaging with cotton bandage duly impregnated in POP solution..Cost of the additional pipe is deemed to be included in the quoted rate. No extra payment shall be allowed for the same.

(a) DG Set of Capacity 20 KVA . (Refer item Nos. 22.00, 22.01 & 22.02 above)

(b) DG Set of Capacity 30 KVA . (Refer item Nos. 22.00, 22.01 & 22.02 above)

(c) DG Set of Capacity 40 KVA . (Refer item Nos. 22.00, 22.01 & 22.02 above)

(d) DG Set of Capacity 50 KVA . (Refer item Nos. 22.00, 22.01 & 22.02 above)

M&L for Earthing complete with galvanized steel earth plate 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25 Mtr deep below normal ground level) with top edge of plate not less than 1.5 Mtr below normal ground level connected to galvanized iron strip size 32x6mm as earthing lead by means of bolt ,nuts, check nuts and washer of galvanized iron or steel besides welding of all joints as shown in drawing and including excavation and earth work, G.I.pipe light grade 40 mm bore for protection of G.I.strip from earth electrode to and including the earth test point of galvanised iron /steel of size 75 x75x 25 mm , supplying and laying charcoal dust, common salt PCC 1:2:4 type B-I using 20 mm stone aggregate for chamber and MS angle iron frame 40x40x3mm and RCC cover 40 mm thick (1:2:4) type BI using 20 mm graded stone aggregate reinforced with 8 mm dia TMT bars @ 75 mm c/c both ways with MS handle 12 mm dia, round ,PGI funnel and wire mesh, 20 mm dia GI pipe light grade for watering all as shown in Plate no 3 of SSR Part I of 2009 and connected to earth test point & testing including dismantling and taking out old U/S Earthing materials complete all as specified and directed. Note :- Cost of earthing strip & GI pipe 40mm up to 7.5 m shall be included in cost of above item.

Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 32 x 6 mm GI Strip continuity earth conductor complete all as specified and as directed.

S&F Weather Proof thermo plastic (Polysterene) Cable Junction box , having protection class IP-66 and of overall size 450mm x 300mm x 170mm having metric knockouts on the wall, duly fixed with the pole with aluminium strip (25x3mm) clamp, GI bolts, nuts, washers and 2 Nos polymide weather proof cable glands of cable sealing range 28mm to 38mm (Complete with check nut) and including 1 No 30 Amps 5 Way cable connector and 1 No. 6 Amps SP MCB. Make of Box : HENSEL (Cat No.- K 7005) or Equivallent model in SPELSBERG / RITTAL Make of Cable gland : HENSEL (Cat No. - 1545.50.1.38) or Equivallent in SPELSBERG / RITTAL / GEWIS

S&F Copper wire PVC insulated 3 Core multistranded of size 1.5 Sq. mm with FRLS PVC insulated copper conductor, cable in surface/ recessed as required from Junction Box to Street light fittings complete all as specified and directed.

Material and Labour for making 2 Nos hole (20mm) in steel tubular pole by using gas welding/electric arc welding for insertion of wire for street light (from pole mounted street light junction box to street light). The holes should be carried out at 15mm above ground level and 1200mm below top level of the pole including grinding the surface of pole for proper smoothness complete all as specified and as directed.

S&F MCCB 63 Amps 4 pole 415 Volts 16 KA Amps with MS enclouser fixed in Existing LT Panel

S&F MCCB 100 Amps 4 pole 415 volts 16 KA Amps with MS enclouser fixed in Existing LT Panel

S&F ON LOAD change over switch 415V in sheet metal enclosures 4 pole of capacity 80 Amps complete all as specified and as directed. (Loc - Base Ops)

S&F ON LOAD change over switch 415V in sheet metal enclosures 4 pole of capacity 63 Amps complete all as specified and as directed. (Loc - Base Ops)

S&F ON LOAD change over switch 415V in sheet metal enclosures 4 pole of capacity 40 Amps complete all as specified and as directed. (Loc - Base Ops)

Taking out existing old corroded LT Feeder pillar box complete incl all MCCB/MCBs etc

Taking out existing old corroded Earthing incl Earth plates etc

Taking out existing unserviceable LT UG cables of sizes 95 Sqmm 3.5 Core

Taking out existing unserviceable LT UG cables of sizes 70 Sqmm 3.5 Core

Taking out existing unserviceable LT UG cables of sizes 50 Sqmm 3.5 Core

Taking out existing unserviceable LT UG cables of sizes 35 Sqmm 3.5 Core

Taking out existing unserviceable LT UG cables of sizes 25 Sqmm 4 Core

Taking out existing unserviceable LT UG cables of sizes 16 Sqmm 4 Core