GENERAL-HT Work-Urgent Conversion of 11 KV DHT service connection in to 11 KV HT at KanjoorLIS under Electrical Wing(I) Section Kalady-HT-Electrical-Work

Amount

HT Works

OD120497/2024-2025:Supply and erection of two pole structure consisting of 2 nos 11 mtrs long 175x85 RSJ poles and fixing the pole excluding excavation of trench and providing PCC of 1:3:6 mm of 40mm metal at bottom and RCC 1:2:4 of 20 mm metal at top with size 600x600x1980 mm and neatly plaster over the earth portion of plinth and neatly painted the pole with 2 coat aluminium paint over a coat of primer as required

OD150390/2023-2024:Supply and fixing of channel iron 100mm X 50 mm X 6 mm (9.56 kg per meter) for placing and fixing ABS/ Lightning arrestor using suitable size bolt and nuts , paint in 2 coat aluminium paint

OD150391/2023-2024:Supply, conveyance, fitting and commissioning of approved make 11 KV,400 Amps, out door type gang operated, Polymer type Air Break triple pole switch with all necessary accessories including adequate length of GI pipe as operating lever, operating handle with insulation and locking arrangements on suitable height, with necessary clamps, nut, bolt, washer etc. as required.

90.17.8.2:Providing, laying, testing & commissioning of 'B' class heavy duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :32 mm

13.10:Supplying and erection of 11 KV pin insulator complete with large steel head G.I. pin, nuts, washers etc. as required

13.13:Supplying and erection of three piece nonlinear resistor type lightning arrestor suitable for 3 wire. 11 KV overhead lines with rated voltage 9 KV (rms) with a nominal discharge current rating of 5 KSA and complete with galvanised clamping arrangement, G.I. bolts, nuts, washers etc. as required.

OD150392/2023-2024:Supply, conveyance, fitting and commissioning of approved make 11 KV, Drop Out Fuse Unit with all standard accessories GI / MS Chanel, properly fixing on cross arm including giving connections etc. as required.

13.1:Supplying and erection of galvanised stay set for 11 KV over head lines complete with 19/ 20 mm dia X 1.8 metres long stay rod, anchor plate of size 45 cm X 45 cm X 7.5 mm thick, thimble, stay clamps, turn buckle ( 20 mm X 600 mm ), 7/ 4.00 mm dia G.I. stay wire and 11 KV strain insulator etc in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size ) foundation including excavation and refilling etc. as required.

OD150397/2023-2024:Supply, installation, testing and and commissioning of 500 KVA,11KV/433 V 3 phase 50 Hz copper wound out door type ONAN cooled transformer having vector group of Dyn 11 , cable box on LT side, Off circuit tapping's of +5% to -10 % in steps of 2.5 %, first fill of oil and standard fittings conforming to IS 1180 Level -1 specification. Intrans/Unitech or equivalent make

OD120484/2024-2025: Supply and fixing of Outdoor type panel with 11kV, 630A, 26.3kA for 3 sec Horizontal Draw out VCB fitted with Manual/Motor operated spring charging mechanism with 230V AC motor and motor control switch, shunt trip coil of 24V DC, closing coil of 24V DC, Auxiliary Contact 2NO + 2NC, Mechanical ON/OFF indicator, mechanical operation counter, protection CT, (--/5A, 5P10, 15VA , 11kV/110V, Cl-0.2, 25VA PT Instantaneous IDMT relay with Microprocessor based 3O/C + and 1EF Protection relay, Strip Heater with thermostat, Digital Ammeter and Digital Voltmeter, Power pack 230V AC-24 V DC emergency OFF push button with HT Metering (3nos CT & 1 no PT Unit ), Provision for TOD Meter

OD150394/2023-2024:Supply, conveyance, erecting testing and commissioning of approved make 3 phase, 4 wire, 110 V ( L-L), -/1 A CT or -/5A CT with DLMS compliant, having RS 485 port of class 0..2 S class TOD meter in the existing meter box after submitting the test certificate from KSEB TMR Division, giving all connections etc. as required. (excluding testing fees)

13.11:Supplying and erection of 11 KV disc insulator for 11 KV over head lines with galvanised insulator fittings, ball and socket type and complete with galvanised strain clamps, bolts, nuts, washers etc. as required.

OD121979/2024-2025:Supply and laying of 3 core 300 sq.mm 11KV stranded compact circular aluminium conductor, conductors screened with extruded semi conducting compound XLPE insulated, insulation screened with extruded semi conducting compound in combination with copper tape (0.3KA for I sec.) cores laid up. inner sheath of PVC ape, galvanized steel flat strip armored, and overall PVC sheathed cable conforming to IS: 7098 part II 1985 with latest amendments, on existing GI cable tray/pipe

90.12.12.5:Supply & laying of DWC pipe in ordinary soil 1.2 m below ground level including excavation90/75 mm or nearest size

10.4.4:Supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required:300 sq. mm

10.5.4:Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :300 sq. mm

OD121993/2024-2025:Supplying siemens / trapdoor type nickel plated Double compression brass cable gland for PVC insulated and PVC sheathed armored aluminum/ copper conductor cable 11 KV grade, and making end termination suitable for 2/ 3/ 3½/ 4 core cable of the following sizes as required. 300 sq.mm

14.1:Excavation for foundation in soft soil including dressing of sides and ramming of bottoms, lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 metres.

14.9:Providing and laying in position cement concrete 1 :3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) in foundation of pump, DG set etc. including form work etc. as required.

14.10:Providing and laying in position reinforced cement concrete 1 :2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) in foundation of pump, DG set etc. including form work etc. as required (excluding reinforcement).

14.12:Providing 15mm thick cement plaster of mix 1:4(1 cement: 4 fine sand) at all levels

OD150401/2023-2024:supply and spreading of fine sand in HT yard

OD150402/2023-2024:Supply conveyance and laying 40 mm size broken stone in the ground of HT yard as required

2.22:Providing and fixing H.T. danger notice plate of 250 mm X 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

90.14.5:Supply and fabrication conveyance and installation of angle iron frame work for wall mounting panel board

LT cable 3.5 core, 400 Sq mm Aluminum,3 runs

90.12.1.37:Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in ground including excavation of trench of size 35 x 75 cm, refilling the trench etc. as required but excluding sand cushioning and protective covering (in ordinary soil).3.5 core 400 sq mm

90.12.2.37:Supply and laying of one number additional PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in ground in the same trench in one tier horizontal formation including widening the trench by 20 cm, refilling the trench etc. as required but excluding sand cushioning and protective covering (in ordinary soil)3.5 core 400 sq mm

90.12.7.37:Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.3.5 core 400 sq mm

90.12.7.35:Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.3.5 core 240 sq mm

90.12.7.34:Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.3.5 core 185 sq mm

90.12.7.33:Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.3.5 core 150 sq mm

90.12.7.30:Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.3.5 core 70 sq mm

90.12.7.27:Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.3.5 core 25 sq mm with factory made clamp

90.12.38.1:Supply and Laying of one number additional PVC insulated and PVC sheathed armoured copper power cable of 1.1KV grade of the following sizes in ground in the same trench in one tier horizontal formation including widening the trench by 20 cm, refilling the trench etc. as required but excluding sand cushioning and protective covering (in ordinary soil)2 core 4 sq mm

9.1.31:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 400 sq. mm (82mm)

9.1.29:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 240 sq. mm (62mm)

9.1.27:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 185 sq. mm (57mm)

9.1.26:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 150 sq. mm (50mm)

9.1.23:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 70 sq. mm (38mm)

9.1.20:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X25 sq.mm (28mm)

90.12.9.6:Supplying, laying and jointing of the following sizes of double wall corrugated (DWC) pipes made out of HDPE conforming to IS 14930 Part II for mechanical protection to underground power cables with all required accessories in ground in the existing trench110/94 mm or nearest size

90.12.9.2:Supplying, laying and jointing of the following sizes of double wall corrugated (DWC) pipes made out of HDPE conforming to IS 14930 Part II for mechanical protection to underground power cables with all required accessories in ground in the existing trench50/38 mm or nearest size

OD122105/2024-2025:Supply and providing20x3mm earth clamps made out of copper strip including cutting and bending the flat exactly tot the shape of the gland drilling necessary holes for nut and bolts tinning the points of contact and giving to the main earthing system as required for earthing gland of size 120sqmm to 400sqmm

OD122103/2024-2025:Supplying and providing earth clamps for siemens/ tropodur type cable glands of suitable length and other dimensions noted along with each size of glands for the following sizes of cables as required.(25 sq - 95 sq mm with 12 mm wide x 1.20 mm thick clip)

OD150413/2023-2024:Supplying , threading , laying and jointing of the following sizes of 100 mm dia B class GI pipe with all required accessories.

7.10:Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required.

Replacement of damaged panel boards & switch gears

90.14.1.1:Fabrication, supply, conveyance, installation testing and commissioning of floor or wall mounting, dust and vermin proof, cubicle type MV panel board comprising of the following components/ devices & complying to IS 8623. Fabrication of fully partitioned, dust and vermin proof enclosure for panel assembly as per form 4 of IS 8623 (with latest amendments) using CRCA sheet as per approved design and requirement, with front and rear access facility, bus bar chambers, hinged doors for all switch gear compartments, earthing the doors using 4 sq mm braided copper conductor, providing necessary cut-outs for mounting meters, relays, indication lamps, bus bar interconnection etc, detachable covers for bus bar chamber and cable alley, powder coating the assembly after subjecting to 7 tank process etc as required. CRCA sheet alone be used for the fabrication. Angles/ flats/ slotted angles etc shall not be used for the fabrication of panel assembly. The measurments will be taken the area of the complete sheets used for panel board including partitions, folding, shrouding etc.Supply and fabrication of MV panel board using 2.00mm CRCA sheet, powder coated (excluding base frame)

90.14.2.1:Supply and providing 2mm SMC sheet as shrouding for bus interconnection / terminations etc. including required nut & bolt etc.

90.14.3.3:Supply and providing heavy duty 'A' section neoprene gasket in the panel boardSupply and providing 'U' section PVC beeding in the panel board

OD150344/2023-2024:Carrying out control wiring for panel with normal meters and indication lamps for interconnecting the control devices/ equipments including providingsuitable size insulated sockets at the termination points or soldered properly, providing numbering ferrules for the proper identification of the wiring,keeping the wiring firm by suitable tie/ tie mounts/ PVC duct etc as required.-1.50 sq mm single run with required sockets.

90.14.4:Supply and fabrication conveyance and installation of base frame of panel board using 75 x 40 mm rolled steel channel (ISMC)

90.14.5:Supply and fabrication conveyance and installation of angle iron frame work for wall mounting panel board

90.14.6:Supply and providing copper bus bars including finger type SMC bus bar supports in the bus chamber, suitable size nut & bolt, providng heat shrink sleeves etc. as required.

90.14.7:Supply and providing copper earth bus in the panel board

OD150345/2023-2024:Supply & fixing Illuminated Flush head Actuator - Red with legend "OFF" (Contact - 1NC)

OD150346/2023-2024:Supply & fixing Illuminated Flush head Actuator - Green with legend 'ON', (Contact - 1 NO)

OD150353/2023-2024:Supply and installation of LED indicators for power/on-off/trip-different Colors

OD150348/2023-2024:Supply and Fixing of 800/5 A, 15 VA, accuracy class 1, Resin Cast Metering CT

OD150347/2023-2024:Supply and installation of 400/5 A, 5 VA, accuracy class 1, Resin Cast Metering CT

OD150352/2023-2024:Supply and fitting Multifunction meter to read: V, A, F, 3 phase accuracy class 1

OD150351/2023-2024:Supply and installation of Three phase Ammeter (V - RY, YB, BR, R, Y, B) of accuracy class 1

OD150350/2023-2024:Supply and installation of Three phase Voltmeter (V - RY, YB, BR, R, Y, B) of accuracy class 1

90.14.8.11:800 A, 4 pole, manual draw out type, microprocessor based ACB with overload , instantaneous SC , delayed SC and ground fault protection 50kA

OD150354/2023-2024:Supply, fixing testing and commissioning of suitable type Standby lowest Earth fault relay L & amp; T MC12AB50X00 or Equivalent

OD150355/2023-2024:Supply and laying of 2 x 6 sqm Aluminum cable from neutral CT to ELR of each transformer in the existing DWC including terminations with suitable lugs , both ends .

OD150356/2023-2024:Supply and Fixing of 200/5 A, 10 VA, accuracy class 10P 10, Protection CT (Tape wound)

OD122409/2024-2025:Transportation, Supply, Installation, Testing and Commissioning of FCMA SOFT STARTER with following ELECTRICAL PARAMETERS: Model No. STD-150-6W, Motor Rating 140 Kw/190 HP, Operating Voltage 415V, Control Supply Voltage 220 VAC, Duty Cycle 4 equal spaced starts per hour, Type of Soft Starter FCMA Soft Starter, Protections/ Metering 1] Built in CT for metering and protection, 2] Built in Digital Micro processer Motor Protection Relay (Short Circuit Over Load,Under Voltage, Single Phasing, Dry Running, Unbalance, Lock, Rotor,Under Current etc.), 3]Reverse Phase relay, Connection In side Delta ( 6 wire), Features Panel with individual lock & key arrangement Remote Operation a] Start / Stop / Reset Push Button, b] Panel with individual lock & key arrangement, Ambient Temperature & Altitude 50° C/ 1000 meters above sea level Line/Bypass device Air break contactor. MECHANICAL PARAMETRS : Enclosure Fabricated 16 SWG CRCA Sheet IP 41, Cable Entry Bottom Removable cable gland plates of MS Materials, Surface Finish Epoxy Powder Coated, Method of cooling Natural Air Cooled Application Pump Reference IS/IEC standards 53/60289/60076/9920/16227/2016/3156/1992/325/2165/12261/2071/-6/ 60071-2/ 3427,298/289 / 13947 / 3043 / 1901 / 2705 / 3156 / 13118 / 5561 / 250

2.2.18:Providing and fixing following rating and breaking capacity and pole MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.400 Amp, 50 KA, 4 pole

90.14.11.4:MCCB AccessoriesSupply and fixing one number earth fault Relay up to 630A to 800A with CBCT.

90.14.11.11:MCCB AccessoriesSupply and fixing one number under voltage release for all voltage range up to 630A MCCB.

90.14.11.12:MCCB AccessoriesSupply and fixing shunt release for all voltage range up to 630A.

90.14.11.16:MCCB AccessoriesSupply and fixing rotary handle, Direct type (including BUC handle with door interlock ) in the existing MCCB of rating up to 630A.

2.1.8:Providing and fixing following capacity TP&N disconnector fuse switch unit inside the existing panel board with ISI marked HRC fuses including drilling holes in cubicle panel, making connections, etc. as required.400 Amp TP&N

2.1.7:Providing and fixing following capacity TP&N disconnector fuse switch unit inside the existing panel board with ISI marked HRC fuses including drilling holes in cubicle panel, making connections, etc. as required.320 Amp TP&N

2.1.6:Providing and fixing following capacity TP&N disconnector fuse switch unit inside the existing panel board with ISI marked HRC fuses including drilling holes in cubicle panel, making connections, etc. as required.200 Amp TP&N

2.1.4:Providing and fixing following capacity TP&N disconnector fuse switch unit inside the existing panel board with ISI marked HRC fuses including drilling holes in cubicle panel, making connections, etc. as required.125 Amp TP & N

OD122210/2024-2025:Supply and fixing following capacity switch fuse unit with ISI marked HRC fuses in sheet enclosure, making connections, etc. as required.400 amps TPN

OD122211/2024-2025:Supply and fixing following capacity switch fuse unit with ISI marked HRC fuses in sheet enclosure, making connections, etc. as required.200 amps TPN

OD122217/2024-2025:Supply and fixing following capacity switch fuse unit with ISI marked HRC fuses in sheet enclosure, making connections, etc. as required.315 amps TPN

90.11.1.14:Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required4 way (8+12) - double cover TPN vertical DB with provision for fixing 4P MCB / Isolator/ RCCB/ RCBO as incomer and SP/ TP MCB as outgoing (IP 42/43)

2.13.2:Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

2.15.3:Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

2.10.4:Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Triple pole

2.10.1:Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

OD150367/2023-2024:Supply and fixing 8 stage 440 / 110 V 5A/1A , Intelligent Power Factor Controllers (IPFC)

90.6.4.53:Supply and drawing 650/1100 V grade FRLS PVC insulated stranded single core copper conductor cables conforming to IS 694 part I 1990 in the existing surface / recess conduit as required including giving necessary connections of the following sizes.10.00 sq.mm 3 Run

1.17.30:Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 6 sq. mm

1.17.21:Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 4 sq. mm

1.17.12:Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 2.5 sq. mm

OD122636/2024-2025:Supply and fixing of Power Capacitor duty contactors for switching capacitor banks 25 kVAR with AC Coil

OD122628/2024-2025:Supply and fixing of Power Capacitor duty contactors for switching capacitor banks 20 kVAR with AC Coil

OD150372/2023-2024:Supply and fixing of Power Capacitor duty contactors for switching capacitor banks 15 kVAR with AC Coil

OD150373/2023-2024:Supply and fixing of Power Capacitor duty contactors for switching capacitor banks 7.5-10 kVAR with AC Coil

OD150374/2023-2024:Supply and fixing of Power Capacitor duty contactors for switching capacitor banks 5 kVAR with AC Coil

90.14.24.31:Supply & fixing the following Power Capacitors 3 phase delta connected in positon and giving connection.5 KVAr, 3 phase, 440 V, Metalised Poly Propylene Heavy duty Cylindrical Gas filled Capacitor suitable for APFC panel without block reactor.

90.14.24.33:Supply & fixing the following Power Capacitors 3 phase delta connected in positon and giving connection.7.5 KVAr, 3 phase, 440 V, Metalised Poly Propylene Heavy duty Cylindrical Gas filled Capacitor suitable for APFC panel without block reactor.

90.14.24.34:Supply & fixing the following Power Capacitors 3 phase delta connected in positon and giving connection.10 KVAr, 3 phase, 440 V, Metalised Poly Propylene Heavy duty Cylindrical Gas filled Capacitor suitable for APFC panel without block reactor.

90.14.24.36:Supply & fixing the following Power Capacitors 3 phase delta connected in positon and giving connection.15 KVAr, 3 phase, 440 V, Metalised Poly Propylene Heavy duty Cylindrical Gas filled Capacitor suitable for APFC panel without block reactor.

90.14.24.37:Supply & fixing the following Power Capacitors 3 phase delta connected in positon and giving connection.20 KVAr, 3 phase, 440 V, Metalised Poly Propylene Heavy duty Cylindrical Gas filled Capacitor suitable for APFC panel without block reactor.

90.14.24.38:Supply & fixing the following Power Capacitors 3 phase delta connected in positon and giving connection.25 KVAr, 3 phase, 440 V, Metalised Poly Propylene Heavy duty Cylindrical Gas filled Capacitor suitable for APFC panel without block reactor.

OD122715/2024-2025:Supplying and fixing 100 amps rating, 415 volts, Triple pole "D" curve, miniature circuit breaker in the existing panel board complete with connections, testing and commissioning etc. as required.

OD150375/2023-2024:Supplying and fixing 63 amps rating, 415 volts, Triple pole "D" curve, miniature circuit breaker in the existing panel board complete with connections, testing and commissioning etc. as required.

OD150376/2023-2024:Supplying and fixing 6 amps to 32 amps rating, 415 volts, Triple pole "D" curve, miniature circuit breaker in the existing panel board complete with connections, testing and commissioning etc. as required.

OD122780/2024-2025:Supply & amp; fixing of 2 lock and 1 key Castell key lock set for 315 to 630A SDF

OD150386/2023-2024:Electrical drawing preparation charge for getting approval from Electrical Inspectorate , A3 sheet for first copy

OD150385/2023-2024:Electrical drawing preparation charge for getting approval from Electrical Inspectorate , A3 sheet - additional copy

OD150387/2023-2024:Supply and providing First Aid Chart duly framed and placed in a conspicuous location for clear vision.

OD150388/2023-2024:Supply and providing 9 Liter capacity GI Fire Bucket painted in post office red with primer coat of red oxide and written with white paint 'FIRE' mounted on MS angle frame work/ wall bracket filled with fine sand, painting the bracket/ floor stand including making good the damages, color washing etc. as required.

OD150358/2023-2024:Painting letters or figures of the following sizes with enamel paint as identification mark to SB, DB, panel board etc as required- 2.50 cm, 4 cm or 5 cm height

OD150361/2023-2024:Aluminium anodised Danger Notice Board of size 150 x 100 mm. with inscriptions ( both in English and Malayalam) and conventional Skull and Bone in Red color.

OD150362/2023-2024:Disconnecting all electrical connections, dismantle the existing panel board , conveying panels to suitable place

OD150363/2023-2024:Supply and providing 6 Kg. Dry Chemical Powder type Fire Extinguisher with hose and clamps including fixing it to wall as required.

OD150364/2023-2024:Supply and providing 2.0 mm thick Elastomeric fire retardant insulating mat as per IS 15652/2006 to withstand 3.3 KV dielectric strength.

OD150365/2023-2024:Supply and providing 11 KV rubber hand long glove

Earthing

OD150404/2023-2024:Supply and providing plate earthing as per IS 3043 with 1200x1200x12 mm GI/CI earth plate, 50 mm GI watering pipe fixed to the earth plate with 25 x 3mm GI clamps, GI funnel with weld mesh, filling required quantity of charcoal including construction of inspection chamber with a bed concrete of 1:4:8 PCC using 40 mm broken stone (10 cm thick), brick work in cement mortar 1:6, plastering the surface of brick masonry and the exposed surface of PCC bed with cement mortar 1:4, 12 mm thick, (the finished inside dimension shall be 450 x 450 x 450 mm) but excluding test joint, earth continuity conductor to the plate, and covering at the top. (in ordinary soil)

5.4:Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

OD124219/2024-2025:supply and providing test joint for the earthing system using 25x6mmGI strips including cutting and bending and bend to shape drilling necessary holes and fixed to the watering pipe etc as required

OD150408/2023-2024:Supply and providing test joint for the earthing system using 25x6 mm copper strips including cutting and bending to shape, drilling necessary holes and fixed to the watering pipe etc as required.

OD124308/2024-2025:supply and providing earth lead from the test joint to the earth plate including25x6mm GI strip including cutting drilling necessary holes and fixing firmly with plate test joint etc as required

OD124307/2024-2025:supply and providing earth lead from the test joint to the earth plate including 25 x6mm copper strip including cutting drilling necessary holes and fixing firmly with plate test joint etc as required

90.16.3.3:Supply and clamping the following size of strips on surface of wall/ parapet/ existing cable tray using clamps fabricated from 20 X 3 mm GI flat duly painted or heavy duty GI spacer saddles spacing of clamps not exceeding 1 m, making good the damages, colour washing etc. as required ( for horizontal run)25 x 6 mm GI strip

90.16.3.10:Supply and clamping the following size of strips on surface of wall/ parapet/ existing cable tray using clamps fabricated from 20 X 3 mm GI flat duly painted or heavy duty GI spacer saddles spacing of clamps not exceeding 1 m, making good the damages, colour washing etc. as required ( for horizontal run)25 x 6 mm copper strip

OD124789/2024-2025:Supplying and laying 25 mm X 6 mm GI strip at 0.60 meter below ground as strip earth electrode, including connection/ terminating with suitable nut, bolt, spring,

OD125435/2024-2025:Supply and laying 25 x 6 mm copper strip tinned at the points of contacts laid 0.60 m below ground level including excavating trench of suitable size and refilling etc. as required (in ordinary soil).

OD150405/2023-2024:Supply and providing the following sizes of cast iron gully trap with covering at the top of the inspection chamber of earth pit as required . - 450 x 450 x 10 mm cast iron gully trap with covering

OD150406/2023-2024:Supply and providing 25 x 6 mm brass bolt & nut with washers on the existing MS box / earth bus etc. as required including drilling necessary holes as required

90.16.1.2:Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required2.65 mm copper conductor (12 SWG)

90.16.1.3:Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required3.15 mm copper conductor ( 10 SWG)

90.16.1.4:Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required4.00 mm copper conductor ( 8 SWG)

90.16.5.2:Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.2.65 mm (12 SWG)

90.16.5.3:Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.3.15 mm (10 SWG)

90.16.5.4:Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.4.00 mm (8 SWG)

ELCON ELECTRICALS (BID ID -2189385)

Bidder Name

Kittu Electricals private limited

ELCON ELECTRICALS