COMPLETION OF INCOMPLETE WORKS FOR SPECIAL REPAIR TO BLDG NO 2FS/01 TO 02, 07/16, 08/01 TO 02 AT MH LANSDOWNE UNDER GE LANSDOWNE

Amount

Dismantling wall and ceiling boards (fiber pulp, insulation etc) or insulation boards / slabs / blankets any thickness including cover fillets / snap grid complete all as specified & directed.

Dismantling un-framed timber scantlings 40 Sqcm in section or over fixed in any position complete all as specified and directed.

Dismantling of boarding, any description and fixed in any position with nails complete all as specified and directed.

Dismantling plain, corrugated or RMP sheet any gauge, thickness including Nainital or similar pattern roof coverings complete all as specified and directed.

Demolition of RCC of any description and in any position not otherwise specifically provided for and dispoing the rubbish off the site of work complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floor and paving not exc. 15 cm thick (Below and above ground level) and dispoing the rubbish off the site of work complete all as specified and directed.

Demolition of brick work or stone / boulders masonary including all quoins, arches, pillars etc built in CM and dispoing the rubbish off the site of work complete all as specified and directed.

Taking down Chowkats or frames (without taking off shutters from the frames) from the opening of size exc 1.5 Sqm but not exc 4 Sqm each complete all as specified and directed.

Taking down Chowkats or frames (without taking off shutters from the frames) from the opening of size not exc 1.5 Sqm each complete all as specified and directed.

Taking down door shutters from the frames of any description not exceeding 1 sqm each complete all as specified and directed.

Taking down door shutters from the frames of any description exceeding 1 sqm but not exceeding 2 sqm each complete all as specified and directed.

Dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing) and removing rubbish off the premises complete all as specified and directed

S & F pre-painted galvalume aluminium zinc coating AZ-150 GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed.

S & F 0.63 mm thick galvanized corrugated iron (CGI) sheeting with two corrugation side lap inclusive of both sides fixed with coach screws and washers as in roof covering, walls etc with grade of Zinc coating 275 complete all as specified and directed.

S & F 0.63 mm thick Plain, galvanised, mild steel sheeting (PGI), as in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of Zinc coating 275 fixed with coach screws and washers as in any pattern complete all as specified and directed.

S & F steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to I.S. 1161-1979 grade St.-240 complete all as specified and directed.

S & F second class hard wood (Not less than Hollock wood) as in scantlings, clean sawn and fixed, in un framed work complete all as specified and directed.

S & F second class hard wood (Not less than Hollock wood) as in plain fillets, clean sawn, square, rectngular in section exceeding 6 sqcm but not exceeding 13 sqcm and fixed with nails complete all as specified and directed.

S & F second class hard wood (Not less than Hollock wood) as in plain fillets, clean sawn, square, rectngular in section exceeding 13 sqcm but not exceeding 25 sqcm and fixed with nails complete all as specified and directed.

S & F 6 mm thick plywood grade BWR type BB, fixed to frame work to ceiling with nails complete all as specified and directed.

S & F 20 mm thick 2nd class hard wood boarding planed one side with butt joints and fixed with nails as in roofs, ceiling, partition, fascia, barge, soffit etc. (except flooring and skirting) complete all as specified and directed.

S & F 35 mm thick factory made pannelled shutter of second class hard wood ( Not less than Hollock wood) Plain, framed, panelled (two panel) with lock rail and panel of 9 mm BWP commercial ply on both faces, the size of rail and stile as per IS 1003(part-1) klin seasoned and chemically pressure treated complete all as specified and directed.

S & F Glazed and skelton shutters 35 mm thick of IInd class hard wood ( Not less than Hollock wood), open rebeated and prepared to receive glass, guage, etc(with out sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred moulded beads on both sides for securing glass etc. sizes of members of shutters as specified in SSR Part I, Section - 8 Clause - 8.24(a) supplied and fitted to chowkat complete all as specified and directed.

M & L for pressed steel frames of size 125 mm x 60 mm made out of 1.25 mm thick mils steel sheets for doors with one or more rebate including necessary fittings such as lugs, lock strike plate, hinges etc and M & L for filling of PCC 1:3:6 type C-0 (using stone aggregates), treating the surface with coal tar black paint which is in contact with concrete / brick work / stone masonary and painting two coats of synthetic enamle paint over a coat of red oxide primer after preparation of steel surfaces which is exposed to view complete all as specified and directed.

M & L for pressed steel frames of size 105 mm x 60 mm made out of 1.25 mm thick mils steel sheets for doors with one or more rebate including necessary fittings such as lugs, lock strike plate, hinges etc and M & L for filling of PCC 1:3:6 type C-0 (using stone aggregates), treating the surface with coal tar black paint which is in contact with concrete / brick work / stone masonary and painting two coats of synthetic enamle paint over a coat of red oxide primer after preparation of steel surfaces which is exposed to view complete all as specified and directed.

M & L for factory made Box type steel window made of ERW tube 'P' section of size 60 mm x 25 mm double rebated outer frame, comprises of gauged shutter and glazed & skelton shutter of ERW tube 'P' section of size 50 mm x 20 mm with one / two openable leaf for each shutter consisting of two number sash bars of T-section 20 mm x 3 mm welded to frame with one number vertical mullion of ERW box type T-section of size 60 mm x 25 mm and flat iron 2 mm thick welded / screwed to the frame for fixing of glass including fittings and fixtures like handles, tower bolts, stoppers, cleats, pintal hinges, hold fasts etc complete all as specified and directed. (a) Hold fasts 150 mm long of 12 mm x 3 mm mild steel flat - 04 number, (b) Handle of Z section 20 mm x 25 mm, 100 mm long - 01 number per leaf, (c ) Mild steel tower bolt 150 mm long - 02 number per leaf, (d) Z section stopper 20 mm x 25 mm, 100 mm long - 01 number per leaf, (e) Cleat 55 mm long of hollow square 15 mm x 12 mm - 02 number per leaf, (f) Mild steel pintal hinges of size 75 mm x 12 mm - 02 number per leaf. Note :- (a) Mild steel guard bars, sheet glass, wire mesh and painting shall be measured and paid for separately under appropriate items of Sch 'A'. (b) For the purpose of measurements and payment, the double shutter with frame shall be measured as one unit.

M & L for factory made Box type steel ventilator made of ERW tube 'P' section of size 60 mm x 25 mm single rebated outer frame, comprises of glazed & skelton shutter of ERW tube 'P' section of size 50 mm x 20 mm with side hung shutter and flat iron 2 mm thick welded / screwed to the frame for fixing of glass including fittings and fixtures like handles, tower bolts, stoppers, cleats, pintal hinges, hold fasts etc complete all as specified and directed. Note :- (a) Mild steel guard bars, sheet glass and painting shall be measured and paid for separately under appropriate items of Sch 'A'.

S & F mild steel framed work such as grills, gratings etc with ends of bars shouldered and / or riveted forged into spikes, framed guard bars, railings and the similar works conforming to Fe-410-O or Fe-310-O complete all as specified and directed.

S & F Solid PVC Door Frame of size 50mm x 47 mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing mentioned in Section 8 of SSR-II complete all as specified and directed.

S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing mentioned in Section 8 of SSR-II complete all as specified and directed.

S & F 100 mm long stainless steel butt hinges, medium weight complete all as specified and directed.

S & F 75 mm long stainless steel butt hinges, medium weight complete all as specified and directed.

S & F 150 mm long (Length of bolt) mild steel barrel tower bolt, stove enamelled black with bright bolt complete all as specified and directed.

S & F 300 mm long (Length of bolt) aluminium alloy, anodised sliding door bolts, with hasp & staple (clip type), cast or extruded sections and fixing bolts and sliding bolt of extruded sections or cast aluminium alloy and including a minimum of 6 bolts and nuts ( four on bolt plate and two on staple plate) complete all as specified and directed.

S & F 125 mm long aluminium handles, cast type, anodised complete all as specified and directed.

S & F 100 mm long aluminium handles, cast type, anodised complete all as specified and directed.

S & F 150 mm long mild steel pressed handles, oval type, stove enamelled black complete all as specified and directed.

S & F 100 mm long mild steel pressed handles, oval type, stove enamelled black complete all as specified and directed.

S & F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel tinned tacks complete all as specified and directed.

S & F in replacement stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel tinned tacks complete all as specified and directed.

S & F 300 mm mild steel ordinary rat tail, rod pattern springs including roller and roller plate complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden / steel frames, glazed with putty or fixed with beads and removing rubbish off the site complete all as specified and directed.

S & F 3 mm thick pin headed sheet glass, ordinary quality and glazing with oil putty or fixed with beads in square not exc. 0.5 Sqm in each pane complete all as specified and directed.

S & F 3 mm thick plain sheet glass, ordinary quality and glazing with oil putty or fixed with beads in square not exc. 0.5 Sqm in each pane complete all as specified and directed.

S & F in replacement 12 mm thick particle board, medium density, flat pressed, single layer type or three layer type with BWR type adhesive, fixed with screws as in pelmet boxes or similar works complete all as specified and directed.

S & F mild steel continuous piano type hinges bright finishes or electro galvanized with width or flap 30 mm ( when opened) complete all as specified and directed.

M & L for PCC 1:2:4 Nominal Mix type B-0 (using 12.50 mm grade stone aggregates) as in fixing of hold fasts, coping and similar works including necessary form work weathering, slightly rounded or chamefered angles and throating complete all as specified and directed.

M & L for PCC 1:3:6 Nominal Mix type C-2 (using 40mm graded stone aggregates) as in surface channels, drains or benching including necessary form work weathering, slightly rounded or chamefered angles and throating complete all as specified and directed.

M & L for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement including forms, moulds, mitred / stopped ends etc complete all as specified and directed.

S & F Hasp and staple, safety type, 75 mm of aluminium anodized with mild steel hinge pin including bolt to hinge plate and fixed with screw complete all as specified and directed.

S & F in replacement 20 mm dia mild steel visa pattern chromium plated wood finish curtain rod with fixing wooden brackets (two per 1.50 RM), wooden stops, rings ( 10 number per 1.50 RM) complete all as specified and directed.

M & L for brick work with sub class 'B' bricks ( old size locally known as Ist Class), straight or curved on plan exc.6 metres mean radius, built in cement motar 1:6 complete all as specified ans as directed.

M & L for raised pointing to randum or polygonal rubble, uncoursed or brought upto course in CM 1:4 to wall on fair faces of brick work / stone masonary complete all as specified and directed.

Racking out joints / pointing from stone / brick masonary and dressing face beds and joints as specified for randum rubble walling, uncoursed and detached joints for flashing and raised pointing to masonary complete all as specified and directed.

M & L for RCC 1:1.5:3 type A-1 (using 20 mm graded stone aggregates) as in slabs supported on walls, beams and columns etc complete all as specified & directed.

Use and waste of form work to the sides and soffits of suspended slab such as roof slab, floor slab etc not exceeding 200 mm thick vertical or batter to rough finish concrete surfaces complete all as specified & directed.

S & F mild steel TMT bars 10 mm dia and over cut to length, bent to shape required including cranking, binding spirally for hooping for columns, hooking ends and binding with and including mild steel binding wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

S & F Non skid ceramic coloured tiles as in flooring of size 7 to 8 mm thick (square / rectangular), area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, set and jointed in neat cement slurry and pointed with white cement mixed with colour pigment to match the colour of tiles over and including 15 mm thick screed bed plaster in CM 1:6 complete all as specified and directed.

S & F Glazed ceramic coloured joint free tiles as in skirting / dado of size 300 mm X 450 mm X 7 mm thick, set and jointed in neat cement slurry and pointed with white cement mixed with colour pigment to match the colour of tiles over and including 10 mm thick screed bed plaster in CM 1:4 complete all as specified and directed.

S & F machine cut pre-polished Udaipur green slab flooring 14 to 16 mm thick as in cooking platform, shelf set and jointed in neat cement slurry and pointed with white cement mixed with admixture of pigment to match the colour of stone over and including 20 mm thick screed bed layer in cement mortar 1:6 including cutting and necessary notching, moulding, chamefered the edges complete all as specified and directed.

S & F machine cut kota stone slab flooring 20-25 mm thick as in floors set and jointed in neat cement slurry and pointed with grey cement mixed with colour pigment to match the colour of slab over and including 20 mm thick screed bed layer in cement mortar 1:6 including cutting, grinding, polishing ( mirror polishing) complete all as specified and directed.

S & F machine cut kota stone slab flooring 20-25 mm thick as in skirting / dado / pillars / risers of step set and jointed in neat cement slurry and pointed with grey cement mixed with colour pigment to match the colour of slab over and including 10 mm thick screed bed layer in cement mortar 1:4 including cutting, grinding, polishing ( mirror polishing) complete all as specified and directed.

M & L for 75 mm thick PCC 1:3:6 Nominal Mix type C-2 (using 40 mm graded stone aggregates) as in plinth protection finished even and fair laid in bays complete all as specified and directed.

M & L for 100 mm thick PCC 1:2:4 Nominal Mix type B-2 (using 40 mm graded stone aggregates) as in path / floor / paving finished even and fair laid in bays complete all as specified and directed.

M & L for 25 mm thick PCC 1:2:4 type B-0 (using 12.50 mm graded stone aggregates) as in sub base floor finished even and fair complete all as specified and directed.

M & L for forming 12 mm thick expansion joints filled with perforated bituminous filler and top 30mm primed amd sealed with sealing compound grade `A` for 75 mm thick complete all as specified and directed.

Taking down cement or cement lime plaster from brick or stone walls etc. including raking out joints, hacking for keys, scrubbing down with water etc. and dispoing the rubbish off the site of work and M & L for 15 mm thick rendering in CM 1:4 on fair faces of brick work finshing even and smooth without using extra cement and applying two coats of cement base paint over a coat of cement primer after preparation of surfaces complete all as specified and directed.

Taking down cement or cement lime plaster from brick or stone walls etc. including raking out joints, hacking for keys, scrubbing down with water etc. and dispoing the rubbish off the site of work and M & L for 15 mm thick rendering in CM 1:6 on fair faces of brick work finshing even and smooth without using extra cement and applying two coats of oil bound distemper over a coat of 3 mm thick Birla white wall care putty after preparation of surfaces complete all as specified and directed.

M & L for preparation of old plastered or unplastered surface on walls by complete removal of the old treatment by scrapping, burnning etc and applying two coats of oil bound distemper over a coat of 3 mm thick birla white wall care putty complete all as specified and directed.

M & L for preparation of old plastered or unplastered surface on walls by complete removal of the old treatment by scrapping, burnning etc and applying two coats of cement base paint over a coat of cement primer complete all as specified and directed.

M & L for preparation of new wooden or previously untreated wooden surfaces exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M & L for preparation of new steel or previously untreated steel surfaces exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S & F in replacement 500 Ltrs capacity rotational moulded polythylene water storage tanks (Cylinderical vertical with closed top) double walled hoisted and fixed in position including PTMT float valve 15 mm bore high pressure with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed (Minimum wt -142grams) complete all as specified and directed.

Taking up or down 15 mm bore steel tubing and connections and S & F 15 mm bore galvanised steel water tubing medium grade with and including all fittings and laid in walls or floors complete all as specified and directed.

Taking up or down 20 mm bore steel tubing and connections and S & F 20 mm bore galvanised steel water tubing medium grade with and including all fittings and laid in walls or floors complete all as specified and directed.

S & F in replacement 15 mm bore bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F in replacement 15 mm bore stop valves / angle valves, cast copper alloy, chromium plated (concealed type) long shank, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

S & F in replacement tubular towel rail of 20 mm dia "D" type 600 mm long of brass chromium plated fixed with & including chromium plated brass screws and wooden / plastic clips complete all as specified and directed.

S & F in replacement 20 mm bore ball valve, high pressure, PTMT, with polythene float and flynut, screwed for iron pipe or brass ferrule complete all as specified and directed.

S & F in replacement sink with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plug, washers, waste coupling 32 mm bore PTMT and waste pipeand bedding in wall in PCC 1:2:4 type B-0 with two number cantilever brackets and connecting to union to pipe overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed.

S & F in replacement 15 mm bore gun metal globe or gate valves with iron wheel head, screwed both ends for iron pipe or for unions complete all as specified and directed.

S & F in replacement 20 mm bore gun metal globe or gate valves with iron wheel head, screwed both ends for iron pipe or for unions complete all as specified and directed.

S & F in replacement PVC Flushing cistern 10 lts caapcity, low level, white with inlte, valve, float, 32 mm bore flush pipe and also connect to WC and handle including Brackets complete all as specified and directed.

S & F in replacement vitreous china water closet (squatt pattern) Orissa type 580 X 440 mm long pan white with CI P or S trap front or back inlet, foot rests including provn of concrete bedding including connections to flushing cistern/pipe complete all as specified and directed.

S & F in replacement PVC connection 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

S & F in replacement cast iron Floor Trap 100 mm dia, with grating including jointing to waste pipe fixed with PCC 1:2:4 type B-0 including necessary cutting complete all as specified and directed.

M & L for cutting chases for concealed piping in brick / stone wall, cutting girth exceeding 10 cm but not exceeding 20 cm girth, pinning in, making good to facing where required and pointing in CM 1:3 complete all as specified and as directed.

S & F in replacement PVC (SWR) pipe 110 mm bore, single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed.

S & F in replacement PVC (SWR) pipe 75 mm bore, single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed.

S & F in replacement 15 mm bore pillar taps, cast copper alloy with crutch or butterfly handle, chromium plated screwed down for high pressure with lettered 'Hot' or 'Cold' with long shank, flynut, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F in replacement chromium plated brass soap dish in approvedd pattern, shape and size complete all as specified and directed.

S & F in replacement stainless steel 0.80 mm thick kitchen plate rack of size 90 cm x 75 cm x 25 cm with all internal fittings as approved by the Eng-in-charge and fixed on wall with gutties complete all as specified and directed.

S & F in replacement Vitreous China Wash hand Basin white, flat back, size 450x300 mm, waste coupling 32 mm bore of PTMT, waste pipe, chain and plug and porcelain stopper and brackets complete all as specified and directed.

Taking down carefully copper / alluminium point wiring (light,fan,sockets & power) complete including fittings such as switches, ceiling roses, pendants, regulators, MCBs, ,Isolator DBs etc and CI/pressed steel terminal switch boxes and making good disturbed surfaces of wall / floor to match the existing surfaces complete all as specified and directed.

M & L for point wiring with 1.5 Sqmm PVC insulated unsheathed, multi stranded copper conductor FR cable single core 1100 Volts grade in and including rigid PVC conduit 20 mm or higher size medium grade in concealed manner with all PVC conduit accessories with provision of CI / pressed steel terminal switch box & white bakelite plastic laminated top sheet cover fixed with brass screws and cup washers and 1.5 Sqmm PVC insulated unsheathed multi stranded FR copper conductor single core 1100 Volts grade as earth wire & wire connected with main earth point for One light / fan / bell point controlled by one one way switch piano type 5 Amp complete all as specified & directed.

All as per Srl item No. 96 here-in-above but for one 3 pin 5 Amp socket outlet on the same board controlled by one, one way 5 Amps piano type.

All as per Srl item No. 96 here-in-above but for one 3 pin 5 Amp socket outlet on the independent board controlled by one, one way 5 Amps piano type.

All as per Srl item No. 96 here-in-above but for one power point wiring for one 15 Amp switch socket combined outlet point on Independent Board with 2.5 Sqmm PVC insulated unsheathed,multi stranded FR copper conductor cable single core 1100 Volts grade and 1.5 Sqmm PVC insulated unsheathed multi stranded FR copper single core 1100V grade as earth wire & wire connected with the main earth point.

S & F switch piano flush single pole one way 5 / 6 Amps complete all as specified and directed.

S & F socket outlet flush single pole 3 / 5 pin 5 / 6 Amp 230 volts complete all as specified and directed.

S & F switch socket combination two in one 6 pin 5 Amp & 15 Amp piano flush type 230 volts AC universal complete all as specified and directed.

S & F bell push piano flush single pole one way 5 / 6 Amps complete all as specified and directed.

S & F bell ding dong AC 230 volts single pole complete all as specified and directed.

S & F ceiling rose PVC / Polycorbonate surface bakelite 65 mm x 50 mm having three terminals complete all as specified and directed.

S & F batten lamp holder PVC / Polycorbonate insulator body with back plate suitable for PVC fitting with fixed on PVC rectangular block of 10 cm x 10 cm x 5cm depth complete all as specified & directed.

S & F in replacement sheet metal enclosure for MCB's DBs single pole & neutral 240 Volts AC with 200 Amp rated neutal bus bar suitable for 8 ways outgoing MCBs double door complete all as specified & directed.

S & F in replacement MCB single pole 240 Volts AC 6 to 32 Amps of 10 KA capacity complete all as specified & directed.

S & F in replacement MCB single pole & neutral 240 Volts AC 32 - 40 Amps of 10 KA capacity complete all as specified & directed.

S & F in replacement decorative wall mounting type 1 x 09 Watt luminare with multicolour made up of polycorbonate rings and glass shade with and including lamp holders, connector block, and LED 1 x 09 W, complete with all accessories prewired and including connecting up with twin core twisted flexible copper conductor cable complete all as specified & directed. Make - Havell's / Insta power Ltd / Phillips / Surya Roshni Ltd

S & F in replacement Exhaust fan, heavy duty metalic body turbo charged of 300 mm sweep 900 RPM single phase 230 volt 50 Hz electric driven including louvers and all fixing accessories and opening hole in existing wall of suitable size and fixing with PCC 1:2:4 type B-0 and connection with copper conductor PVC insulated sheathed cord of suitable size complete all as specified and directed.

S & F in replacement MAXOLED BATTEN for T8 LED retrofit lamp (G 13) with G 13 lamp holders tube light including its connection with 2 core flexible copper conductor cable of suitable size with all accessories complete all as specified & directed. Make :- Havell's CAT part No. LHFXCEPITN1W020 including MAXOLED (TUBE) CAT No. LHEXCEP7UN1W20 of capacity 20 watt or equivalent CAT part of make Insta power Ltd / Phillips / Surya Roshni Ltd

S & F in replacement sub main wiring with two single core PVC insulated, unsheathed, stranded copper conductor cable 4 Sqmm with one single core 2.5 Sqmm PVC insulated, unsheathed, stranded copper conductor cable as earth wire in and including PVC rigid conduit 20 mm dia with its accessories and earth wire connected to common earth dolly complete all as specified and directed. Note: Two run of 4 sqmm cable, one run of 2.5 qsmm cable and one run of PVC conduit shall be measured as one unit

S & F in replacement LED street light luminaire 30 Watt IP-65 complete with all accessories internally prewired fixed on wall with bracket made out of 25 mm dia light grade GI pipe of required length not less than 1.20 mtr duly fitted with mild steel nuts , 150 mm long,12 mm dia bolts and washers and painting with two coats of synthetics enamell paint over one coat of red oxide primer and connected with twin core cable of suitable size, PVC insulated copper conductor multistraded cable of required length and connecting complete all as specified & directed.Make Havell's CAT part No. LHEWEBP7PL6S030 or Equivalent CAT part of Make Insta power Ltd / Phillips / Surya Roshni Ltd

S & F in replacement LED bulk head light fitting 1 x 09 watt complete with LED bulb 1 x 09 watt and batten lamp holder PVC / Polycorbonate insulator body with back plate suitable for PVC fitting with fixed on PVC rectangular block of 10 cm x 10 cm x 5cm depth and all accessories including its connection with 2 core flexible copper conductor cable of suitable size with all accessories complete all as specified and directed. .Make: Havells / INSTAPOWER / Philips / Surya Roshni Ltd

M & L in replacement for earthing complete with galvanized earth plate electrode 600x 600 x 6mm thick buried directly in ground (earth pit not less than 2.25mtr deep below ground level) with top edge of the plate not less than 1.5mtr below ground level connected to galvenised earth lead wire of 4 mm dia by means of nuts, bolts, washes of galvanized iron or steel all as shown in electrical plate No 5 and testing on completion including adequate charcoal dust comman salt necessary excavation & earth work, PCC 1:3:6 type C-1 pit with precast RCC cover slab 40 mm thick in PCC 1:2:4 type B-0 reinforced with 6 mm dia MS round bars @ 100 mm c / c both ways with funnel wire mesh and 20 mm dia GI pipe medium grade as watering pipe including connecting to earthing test point complete all as specified and directed.

OM SAI ASSOCIATES AND DEVELOPERS