Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹27.6 LAccepted-Finance | L1 | Accepted-Finance Bid satisfies all tender requirements | |
| 2 | L2₹35.8 L+₹8.2 L (29.5%)Accepted-Finance | L2 | Accepted-Finance Bid satisfies all tender requirements | |
| 3 | Rejected-Technical | - | Rejected-Technical Documents required for tender not submitted. And firm has informed their withdrawal from this tender. |
Tender Value
Refer Docs
Closing Date
5 Nov 2022, 2:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
DGM
DGM SHIP REPAIR MATERIALS DEPT, CSL, COCHIN
Dredge and jet pump repair work to be carried on DCI vessel Dredge XXI at CKSRU, Kolkata
2022_CSL_133759_1
KP1/Dredge And Jet Pump/Dredge XXI/CKSRU
Open Tender
Marine Services
Turn-key
30 days
CKSRU
Please refer Tender documents.
2 documents required · 2 mandatory
₹0
Exempted
11 Oct 2024
29 Oct 2022
7 Nov 2022
29 Oct 2022
5 Nov 2022
29 Oct 2022
29 Oct 2022 - 4 Nov 2022
DREDGE PUMPS PORT & STBD: Complete overhaul of both Dredge pumps to be carried out. Following job to be done on both Dredge Pump. *** All spares, rubber cords, packings DCI supply
DREDGE PUMPS PORT & STBD: Distance piece, suction & discharge end covers, impeller, diaphragm plate, seal-pot unit/assembly, chrome bush/sleeve, flushing water chamber to be removed. Necessary alignment of pump casing with thrust block shaft to be carried out, prior assembling pump. Pump to be boxed back and satisfactory trials to be shown.
l) Thrust block to be removed from place after disconnecting the toothed coupling in engine room. Thrust block to be transported to the workshop. Bearing, seals & D.P. shaft to be renewed. Thrust block to be fitted back in place after completion of above. Necessary alignment of dredge pump casing with thrust block & toothed coupling to be carried out, prior assembling the Dredge Pump. Bearings, seals & shaft: Ship supply
m) Both Impeller and end cover to be build up, if necessary
i) Buffer Layer (7018)
ii) Hard facing
o) Renewal of Dredge Pump volute casing
JET PUMPS (HORIZONTAL SPLIT-CASING TYPE) -: Jet pump toothed-gear coupling alignment to be checked, axial & radial alignment readings to be taken before removing jet pump from position. Pump to be dismantled, coupling to be removed and overhauled completely. Casing, Wear rings, shaft sleeves and Impeller to renew. Both end bearings to renew. Casing locating pins to install, renew. During overhauling any defect observed, same to be rectified/repaired. Toothed-gear coupling to be cleaned, inspected & any defects noticed to be rectified. After completion of repairs, pumps to be boxed back with new joints (contractor supply), pressure tested for 15 bar for no leak. Pump to be fitted in place, proper alignment done and satisfactory trials to be shown to ship staff. *** All spares ship supply
Pitted/holed portions of casings, wear-ring landing/seating area to be weld-build-up with suitable electrodes
Optional (Shall not be considered for Price comparison)
JET PUMPS (HORIZONTAL SPLIT-CASING TYPE) -:During overhauling any defect observed, same to be renewed.
TOTAL MARINE TECHNOLOGY
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .