SPECIAL REPAIRS TO BLDG NO. T-1A AND 1B AND 1C AND 1K (PERSONNEL LINE TOILET AND BATHROOM AND PASSAGE) AT MILITARY HOSPITAL VADODARA

Amount

Demolition of cement concrete (unreinforced) in ground floor and pavings n.exc.15 cm thickness (below or above ground level) and removing from site all as specified and directed.

M & L for 75 mm thick PCC 1:3:6 type C2 (using 40 mm graded stone aggregate)as in plinth protection and paving, finishing concrete surface even and smooth without using extra cement

M&L for Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

M&L for Treatment of surface under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors and aprons etc. laid, bedded and pointed in any mortar and removing from site all as specified and directed.

M&L for machine cut kota stone slab 20-25 mm thick in flooring laid over and including 15 mm thick cement screed bed or bedding layer in CM 1:4 mixed with high performance adhesive as per manufacturers instructions, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.

M&L for kota stone slab 18-20 mm thick in riser of steps, skirting, dado and pillar laid over and including 10 mm thick backing coat in CM 1:3 on stone masonry surfaces/brick work or concrete surfaces mixed with high performance adhesive as per manufacturers instructions and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.

M&L for glazed ceramic tiles, coloured, 450x300x7mm thick on vertical surfaces such as skirting, dados and risers to steps etc, set & jointed in neat cement slurry & pointed in white or coloured cement to match over and including 10mm thick backing coat in CM 1:3 on stone masonry surface/brick work or concrete surface. (Tile pattern and decoration shall be as directed by Engineer in-Charge.)

M&L for non skid ceramic tiles, coloured, 7 to 8 mm thick (square/rectangular) in floors etc. area of each tile exc. 0.06 sqm but n. exc. 0.11 sqm, set & jointed in neat cement slurry & pointed in white or coloured cement to match ,laid over and including 15mm thick screed bed or bedding layer in CM 1:4 (Tile pattern and decoration shall be as directed by Engineer-in-charge).

Polishing of old existing Kota stone flooring i.e, grinding, joints pigment filling and polishing to get mirror finish all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exceeding 1.5 sqm each and removing from site. Note - Quoted rate shall be deemed to be include for cutting holes/demolition of PCC block/brick work etc for taking down chowkats and making good the damaged surfaces in CM 1:3 all as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exceeding 1.5 sqm but not exceeding 4 sqm each and removing from site. Note - Quoted rate shall be deemed to be include for cutting holes/demolition of PCC block/brick work etc for taking down chowkats and making good the damaged surfaces in CM 1:3 all as directed.

M & L for Green marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade laid over and including 15mm thick screed bed or bedding layer in CM 1:4

S&F aluminium powder coated of any colour (minimum thickness of powder coating 50 micron) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F of Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge.

S&F sheet glass 4 mm thick, ordinary quality and glazing with neoprene beading in square exc 0.5 sqm in each pane.

S&F stainless steel wire cloth, 0.36 nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples or wooden beads supplied with shutters.

S&F 4.00mm thick figured glass, pin head type and glazing with rubber beading or with glazing clips n exc 0.5, all as specified and directed.

S & F for Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete confirming to grade Fe 410-W (Gde- E- 250) quality-A, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete

S&F mild steel of grade Fe-290 (Grade E-165) in framed work such as grills, grating etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders; ramed balusters; walk ways; railings; framework of water tanks and similar works.

M&L for preparation of new or previously untreated steel surfaces of any description, over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 50 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. all as specified and directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary SS screws shall be paid separately).

M&L for 35mm thick factory made Flush shutters, solid core construction, with block board core and plywood face panels, comercial type 1.0mm thick (veneered on both side) with decorative choice laminated type 1 (factory laminated), or surface finish, 6mm thick external teak wood lipping fixed with nails, color and pattern as approved by EIC/GE.

S & F 35mm thick 2nd class Hard wood Glazed and Skelton shutters, open rebated and prepared to receive glass, gauze etc(without sash bars) edges of framing plain, chamfered or rounded, fitted with cut ,mitered and moulded beads for securing glass etc, sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a); supplied and fitted to chowkats.

M & L for preparing new wooden surface of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer.

S&F mild steel of grade Fe-290 (Grade E-165) in bands, straps, supports or stays for rain water, ventilating pipes including bolts, if required, clamps, hold fasts and similar small articles.

M&L for PCC 1:3:6 type C-0 using 12.5 mm graded stone aggregate in cills, steps, bands, copings, bed plates, blocks for inserting hold fasts, filling back of chowkats etc. and the like including weathering, slightly rounded or chamfered angles and throating as directed.

M&L for 100mm butt hinges of stainless steel grade 202, 14 gauge thickness, medium weight of approved make fixed with pressed steel door frame/Angle iron frame/PVC door frame with screw complete all as specified and directed.

M&L for 75mm butt hinges of stainless steel grade 202, 14 gauge thickness, medium weight of approved make fixed with pressed steel door frame/Angle iron frame/PVC door frame with screw complete all as specified and directed.

S&F 200 mm long aluminium, anodized, barrel tower bolts of extruded section and fixed.

S&F 150 mm size extruded aluminium alloy handles, fabricated type, anodized.

S&F 150 mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy.

S&F 250 mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy.

S&F in repairs 22 to 25 mm dia stainless steel curtain rod, fancy type/decorative type, fixed to walls complete all as directed.

S&F in repairs, stainless steel decorative finials (round type with mirror optic finish trade/standard pattern suitable for 22 to 25 mm dia decorative/fancy type curtain rods.

S&F floor door stopper, with 150 mm long cover plate, of aluminium alloy body and tongue, anodized, with hard drawn steel spring, fixed in floor.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete.

Dismantling timber scantlings 40 sq. cm and over in section, in any position

Dismantling Plain or corrugated steel sheeting,any gauge, thickness, including Nainital or similar pattern roof coverings.

S & F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

S & F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

S&F rolled mild steel of grade Fe-290 (Grade E-165) in rolled section as in frames for doors/windows, framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc.

Demolition of cement concrete (reinforced) (reinforcement cut as required to facilitate demolition) roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work and removing from site all as specified and directed.

Taking down cement plaster, any description on brick, concrete or stone walls or ceiling including raking out joints, hacking for key, scrubbing down with water etc and removal of rubbish off all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc. and removing from site all as specified and directed.

M&L for brick work with sub class 'B’ bricks using old size bricks, straight or curved on plan exc. 6 m mean radius, built in CM 1:6.

M&L for rendering 10 mm thick in CM 1:6 on brick work or concrete surfaces finished even and smooth without using extra cement.

M&L for rendering 15 mm thick in two coats ,5 mm thick in CM 1:4 mixed with liquid water proofing compound @ 0.200 litre per bag of 50 kg of cement, finished even and smooth without using extra cement over and including 10 mm thick rendering in CM 1:6 on brick work or concrete surfaces. Note:- Liquid water proofing compound shall be measured and paid for separately as “Supply only”

M&L for preparation of new plastered or unplastered surfaces of walls and applying two coats of distemper oil emulsion, white or tinted, over and including a coat of 3 mm thick Birla/JK wall care putty over a coat of primer all as directed.

M&L for complete removal of existing treatment from walls and applying two coats of distemper oil emulsion, white or tinted, over and including of 3mm thick Birla/JK wall care putty over a coat of primer all as directed.

M&L for complete removal of existing treatment from external walls complete all as directed.

M& L for applying Two coats of damp proof waterproofing coating @ 2.7–3.2 m2/L/coat over plastered surface of exterior wall complete all as per manufacturer instuctions. (Make: Nerolac, Berger or equivalent) (Note: Damp proof coat applied to wall surface before exterior emulsion paint)

M & L for preparation of newly plastered surfaces of walls/ceilings of roof projection and chajjas etc. and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old/new surfaces.

Supply only liquid water proofing compound.

Dismantling Wall and ceiling boards or insulation board any thickness including cover fillets.

Providing and fixing Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers with G.I. wire mesh to hanging including grid of size 605x605 mm Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/ intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre (Fillets, metal frame work and G.I. wire mesh paid separately) complete

Taking up or down steel tubing 15 mm bore and connections

S & F 20 mm outer dia CPVC pipes SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed

Taking up or down steel tubing 20 mm bore and connections

Supply and laying 20 mm bore tubes, galvanized steel, medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors all as specified and directed.

S & F 25 mm outer dia CPVC pipes SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed

Taking up or down steel tubing 25 mm bore and connections .

Supply and laying 25 mm bore tubes, galvanized steel, medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors all as specified and directed.

S & F 32 mm outer dia CPVC pipes SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed

Dismantling of cast iron or reinforced concrete drain pipes of 100 mm internal dia, jointed in cement mortar and taking out of trenches, if required.

Dismantling of cast iron or reinforced concrete drain pipes of 75 mm internal dia, jointed in cement mortar and taking out of trenches, if required.

S&F 110 mm bore UPVC (SWR) pipes type ‘B’, single socketed, in any length, with rubber ring joints, laid in trenches or in floors.

S&F in repairs 110 mm bore UPVC (SWR) bend, suitable for type ‘B’ pipes, any radius.

S&F in repairs 110 mm bore UPVC (SWR) bend, suitable for type ‘B’ pipes, any radius with oval access door.

S&F in repairs 75 mm dia PVC (SWR) bends of any radius with duck foot or heel rest fitted with oval access door complete.

S&F in repairs 110 mm bore UPVC (SWR) vent cowl, suitable for type ‘B’ pipes.

S&F in repairs 75 mm bore UPVC (SWR) vent cowl, suitable for type ‘B’ pipes.

M&L in repairs for PVC (SWR) floor trap, suitable for type ‘B’ pipes, 75 mm dia of outlet, plain with SS grating including jointing with solvent cement.

M & L for PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement

S&F in repairs 15 mm bore bib taps (long body), cast copper alloy, fancy type, chromium plated, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule as per Cat part No. CON-107KN of Make-Jaquar or techno commercially equivalent of any make specified.

S&F 15 mm bore bib taps (long body), cast copper alloy, fancy type, chromium plated, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule as per Cat part No. CON-107KN of Make-Jaquar or techno commercially equivalent of any make specified.

S&F in repairs 15 mm bore stop valve/angle valve, cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or for unions.

S&F in repairs, two way angle valve fancy type chromium plated 15mm bore cast copper alloy with capstan heads, screwed down high pressure with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and directed.

S&F 15 mm bore Pillar taps, cast copper alloy, with capston heads, chromium plated fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and directed.

S&F PVC connection 15 mm size with PTMT nuts of length 450 mm.

S&F in repairs vitreous china wash basin, white/ivory, oval type, size 550x400mm including brackets, cutting for and pinning in ends of brackets or erecting stand, including brass chromium plated perforated waste coupling/fittings 32 mm dia with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed and PVC waste pipe of 32 mm bore and of suitable length complete all as specified.

S&F in repairs brass chromium plated shower rose of 125 mm size with swivel joint including fixing to steel pipe or union.

S&F 32 mm bore low density polyethylene pipe (LDPE) of pressure rating 6 kgf/cm² fixed complete to walls, ceilings or in floors etc. as in waste pipe all as specified and directed by Engineer-in-Charge.

S&F in repairs brass chromium plated tubular towel rail, 20 mm dia, D type, 60 cm long between flanges.

S&F in repairs CP soap dish fixed to wall with brass chromium plated screws complete all as specified and directed. Make : Prayag & equivalent

S&F in repairs Vitreous China Urinal, Half stall type, 420 x 395 x 635 mm white (excluding flushing cistern, flush pipe) white , with grating and union for discharge pipe including chromium plated waste coupling, CP spreader and necessary waste pipe complete all as directed by Engineer-in-Charge.

Dismantling water tanks of any description, exc. 500 & n. exc. 1000 litres capacity and removing from site.

S&F 1000 litres capacity rotational moulded polyethylene water storage tanks triple layer (cylindrical vertical with closed top), hoisted and fixed in position all as specified in SSR Part-I, connecting up pipes.

S&F in repairs 25 mm dia gun metal, globe or gate valve, with iron wheel head, screwed both ends for iron pipe.

M&L for cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate any thickness as in platform for PVC tank over roof and similar work etc as directed.

S&F in repair Vitreous China wash down water closet pan (Europion pattern), white (excluding fixing bolts, flushing cistern and flush pipe) including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor. complete all as specified and as directed.

S&F in repairs Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

S&F in repairs PVC flushing cistren low level, 10 ltr capacity with syphonic action type ball valve. Incl inlet ball valve, PVC band (flush pipe) 32mm complete all as specified.

S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S&F in repairs Vitreous China wash down water closet (Squat pattern ) white complete as fixed in repair excluding flushing cisternand flush type "Orrisa" pattern size 580x440 with integral footrest inject connection to trap antisyphonage etc complete including joint between flushing pipe and socket of WC.

Demolition of reinforced cement concrete as in Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work

M&L for Providing reinforced cement concrete (nominal mix) Type B1, 1:2::4 (using 20 mm Aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like including necessary form work complete all as specified and directed. Note. (reinforcement shall be measured and paid separately)

M & L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specifed and as directed.

Taking down carefully existing unserviceable copper/aluminium point wiring (light, fan, socket or power point etc) complete with fittings/fixures such as switches sockets, ceiling rose, fan regulators, etc (except light fittings), removing materials for taking credit and making good disturbed surface of wall, floors, etc complete all as directed by Eng-in-Charge.

M & L Point wiring complete with 1.5 sqmm single core PVC insulated (FRLS) and unsheathed cable 1100 volts grade with multistranded copper conductor drawn through and including PVC Conduit and all accessories Concealed in walls / roofs / floors / ceiling etc. and including provision of 1.5 sqmm copper cable as earth continuity conductor and connected to common earth dolly, including fabricated steel terminal box made out of 1.60mm thick MS sheet concealed in walls, with 3mm thick laminated sheet top cover for housing the switches, socket outlets, fan regulators etc complete including cutting of chases where as required and making good all disturbed work to match the existing all as specified and as directed for the following:-

One light point controlled by one switch.

One ceiling fan point controlled by one switch and fan regulator.

One exhaust fan point controlled by one switch.

One 3 pin socket outlet 5 Amps independent board.

One 3 pin socket outlet 5 Amps on the same board with other switch.

All as per item No. 102 here-inbefore but with 2.5 sqmm PVC insulated multistranded flexible unsheathed copper conductor inclusive of 2.5 sqmm PVC insulated multistranded flexible copper conductor for one independent 6 pin 16 Amp socket.

S & F switch piano flush type SP one way 6 Amp.

S & F switch socket combination 2 in 1, 3 pin, 6 and 16 amp flush type universal.

S & F switch socket combination 2 in in 1, 5 A flush type.

S & F ceiling rose surface polycarbonate body three terminal.

S & F stepped type electronic fan regulator flush type on the laminated sheet complete.

S & F ceiling fan complete with blades, down rod from existing roof / trus to fall ceiling, and accessories, 230V, 1200mm sweep. Min air delivery 210 CFM with star rated including ceiling fan connecting up with three core flexible copper conductor cable of suitable size from ceiling rose and taking down existing UNSV ceiling fan complete all as specified and directed. Note : 1) Old ceiling fans shall be deposited to AGE E/M store yard .

Supply and fix LED light fitting 1X20Watt, 220 Volt AC decorative box type with drivers, holders and including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete including taking down unserviceable existing light fitting complete all as specified and directed.

Supply and fix exhaust fan made of steel body complete with louvers shutter, voltage 230V, 50Hz, RPM 1200, copper winding of 300 mm sweep heavy duty including cutting of suitable size holes on existing wall and making good disturbed work to match the existing surfaces and exhaust fan connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed Note : 1) Old Exhaust fans shall be deposited to AGE E/M store yard .

Supply and fix CRCA sheet metal enclosures distribution board double door,TPN vertical DB 4 way suitable for fixing of Four pole MCCB as in commer & MCBs SP as out going and duly fitted with Bus bar, neutral link, blanking plates, conforms IS 8623-1 & 3, IEC 61439-1 & 3, IK 09 etc complete.The DB shall be included with one No MCCB, 4 pole, 415/430 Volt, 50 Hz, Ics=100% of Icu, having rupturing capacity 16 kA on 415 V icu of capacity 100 Amps complete all as specified and directed. Encloser & MCCB shall preferably of same make. ( MCB s required for out going shall be measured and paid seperately) Make :- Legrand / Schiender / Siemens and equivalent make

M&L for Sub main wiring with FRLS two single core PVC insulated and unsheathed fire retardant multi stranded copper conductor cable 1100 volt grade IS-694, marked of 6.0 Sqmm size drawn through and including not less than 25 mm dia PVC conduit medium grade ISI marked and conduit junction boxes, terminal boxes and accessories such as tees, bends, elbows, reducers, bell mouth tube ends fixed to the surface of wall/ceiling including one run of 6.0 sqmm PVC insulated and unsheathed FRLS multi stranded copper conductor cable for earth wire continuity conductor. Note : Two runs of single core 6.0 sqmm and one run of 6.0 sqmm copper FRLS cable as earth continuity conductor and suitable size conduit with accessories shall be measured as one length.

S & F sheet metal enclosures (double door) for DBs where MCBs to be used single pole and neutral 8 way 240 V with 200 amps rated bus bar fixed on wall (flush/surface as ordered). Including taking down DBs/Main switches / Busbar box of any type and capacity .

S & F sheet metal enclosures (double door) for DBs where MCBs to be used single pole and neutral 4 way 240 V with 200 amps rated bus bar fixed on wall (flush/surface as ordered). Including taking down DBs/Main switches / Busbar box of any type and capacity .

S & F incl connection MCB single pole, having rupturing 10KA, 240 V 63 amps as ordered.

S & F MCB Single pole and neutral (SPN), having rupturing 10KA, 240 V 63 amps as ordered.

S & F incl connecting MCB single pole, having rupturing 10KA, 6 amps to 32 amps as ordered 240 Volts

S & F in repair LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection including bracket made out of GI pipe light grade 32mm bore not less than 1.20m long bent to shape required fixed to pole with suitable size 2 Nos clamps made out of 25X3mm flat iron with nut, bolts and washers complete complete all as specified and directed

Taking down existing earthing and M & L for Earthing complete with galvanised steel earth plate electrode, 60x60cmx 6.3mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level,connected to galvanised earth lead wire 4.0mm dia by means of bolts,nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion, and excavation and earth work in any type of soil strata

Excavation in trenches not exc. 1.5 m wide and not exceeding 1.5m depth for foundation of poles/laying of cables/stay/strut/ pipes etc or for shafts, wells, cesspits,manholes, pier holes, etc not exceeding 10 Sqm on plan for shafts, cesspits, manholes, pier holes etc and getting out in soft/loose soil complete

Removing excavated material (soil) n.exc 50m and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete

Returning filling in excavated approved soil including spreading, leveling, watering and well ramming in layers n.exc 25cm in soil completed all as specified and directed

Supply and laying dry sand cushioning to UG cable 8 cm thick before laying and 15cm thick after laying complete all as specified and directed. Note:- 1.Dry fine sand of best available quality shall be used. 2.Punned thickness shall be measured and paid.

M & L for Sub class `B` bricks laid dry flat transversely along the length of cable with width equal to the length of bricks as protection cover of cable laid, complete all as specified and directed.

Supply and laying in trenches or passing through pipe, 1100 volts grade heavy duty cable with XLPE insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 25 sq. mm 4 Core nominal cross sectional area complete all as specified and directed

M&L for galvanized steel tubing light Grade of 40 mm dia as in protection of cable fixed to pole/walls or laid in floors, road crossing ducts with all necessary fittings and fittings and fixed with clamps, bolts, nuts and washers etc complete all as specified and directed.

Supply and laying in trenches of GI steel tubing medium grade including all fittings such as Tees, elbow, bends etc for 25 mm bore of pipe complete all as specified.

Supply and laying in trenches of GI steel tubing medium grade including all fittings such as Tees, elbow, bends etc for 20 mm bore of pipe complete all as specified.

S & F 20 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe.

M & L for cutting existing steel tubing for alterations or additions (Each cut measured) and inserting new Tee, bend, elbow etc up to 50 mm dia

City Light (BID ID -3113300)

Badri Electricals (BID ID -3109926)