PROVN OF KOTA STONE FLOORING IN BLDG No. T-38, T-80, T-106 AND T-112 FOR INF BDE CAMP, SPECIAL REPAIRS TO BLDG NO. T-109, T-110, T-191, T-192 AND T-201 OF TRANSIST CAMP AND PROVN OF CERTAIN MINOR WORKS AT DIFFERENT LOCATION OF ALONG MIL STN UN

Amount

B/R SERVICES/WORKS

Demolition Cement Concrete (Un-reinforced) of any description in Ground Floors, Pavings, etc. not exc. 150mm thickness (above or below Ground Level) and Removing debris, etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Demolition Brick Work or Pre-cast Concrete Block Masonry, built in Cement Mortar and in any Position including all Quoins, Arches and Pillars, etc., complete all as specified and as directed.

Dismantling Timber Scantling 40 Sq Cm and Over in Section in Unframed Work, complete all as specified and as directed.

Taking down Chowkat or Frame of any description (without Taking Off Shutter from the Frame) not exc. 1.50 Square Metre Each, complete all as specified and as directed.

Taking down Chowkat or Frame of any description (without Taking Off Shutter from the Frame) of any description, exc. 1.50 Square Metre but not exc. 4.00 Square Metre Each, complete all as specified and as directed.

Dismantling Wrought Iron Work of any description not otherwise provided for, complete all as specified and as directed.

Dismantling Plain or Corrugated Steel Sheeting of any gauge and thickness, Segregating the Serviceable Steel Sheeting, stacking properly at Sites and keep in Safe Custody for re-use, complete all as specified and as directed.

Dismantling Wall and Ceiling Boards (Fibre, Pulp, Insulation, etc.) or Insulation Boards/ Slabs/ Blankets of any descriptions including Cover Fillets, complete all as specified and as as directed.

Dismantling Floor, Hearth or Wall Tiling including Cement Mortar Bedding (but not backing) and removing debris, etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Taking down Cement Plaster including Raking out Joints, hacking for Key, scrubbing down with Water and removing Debris, etc. etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Hacking/Taking out Broken Glass of any description from Wooden or Metal Frames, or Stone, Concrete or Brick surrounds of any thickness or size; Hacking out Old Putty or Removing Beads, etc., complete all as specified and as directed.

Surface Dressing not exc. 15 Cm Deep (avg) and getting out in Soft/Loose soil, complete all as specified and as directed.

Excavation Over Areas, not exc. 1.50 Metre in depth and getting out in Soft /Loose Soil, complete all as specified and as directed.

Excavation Over Areas, exc. 1.50 Metre but not exc. 3.00 Metre in depth and getting out in Soft /Loose Soil, complete all as specified and as directed.

Excavation in Trenches not exc. 1.50 Metre wide and not exc. 1.50 Metre in depth for Foundation etc. or for Shafts, Wells, Cess Pits, Manholes, Pier Holes, etc. not exc. 10 Sqm on Plan and not exc. 1.50 Metre in depth and getting out as in Soft/Loose Soil, complete all as specified and as directed.

Returning, Filling in including Spreading, Levelling, Watering and Well Ramming in layers not exc. 25 Cm, in Soft/Loose Soil, complete all as specified and as directed.

Removing Excavated Materials (Soils) to a distance not exc. 50.00 Metre and depositing where directed at a level not exc. 1.50 Metre above the Starting Point, complete all as specified and as directed.

M&L Sand Gravel (as approved) Filling under Floors or in Foundations including Watering and Consolidation in layers not exc. 150mm thick, complete all as specified and as directed.

M&L Hardcore broken Stone or Boulders, gauge not exc. 63mm, deposited, spread and levelled in layers not exc. 150mm thick, watered and well rammed to a True surface, complete all as specified and as directed.

M&L Cement Concrete 1:4:8 (40mm graded stone aggregate) in Foundation, Filling and Mass Concrete, etc. including necessary Formwork as ordered, complete all as specified and as directed.

M&L Cement Concrete 1:3:6 (20mm graded stone aggregate) as in Coping, Bed Plates, Holdfast, Bed Block, Kerb Stones including necessary Formwork and Weathering, slightly Rounded or Chamfered Angles and Throating, complete all as specified and as directed.

M&L Reinforced Cement Concrete 1:1½:3 (20mm graded stone aggregate) in Foundation including Rafts, Footing, Foundation Beams for Column Basement Slab, under reamed Piles, complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:1½:3 (20mm graded stone aggregate) in Columns, Pillars, Piers, Posts and Struts, etc., complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Walls, Retaining Walls, Basement Walls, Ballast Walls and the like; any thickness; above Top of Footings including attached Pilaster and Buttresses, complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Slabs supported on Walls, Beams and Columns in Floors, Roofs, Landings, Balconies, Canopies, Deck Slabs and in Shelves and the like, complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Pre-cast Reinforced Cement Concrete 1:2:4 (20mm graded aggregate) in Landings, Cover Slabs (for Manholes, etc.), Chullah Hoods, Chajjas, Water Troughs, Mangers, Shelves and Similar Articles with Plain faces and setting in Cement Morter 1:4, complete all as specified and as directed. NOTE : Reinforcement will be Measured and Paid for separately under appropriate Items.

M&L Formwork to Sides of Concrete Foundations, Footings, Base of Columns, Raft and Raft Beams, Sides and Soffits (if any) of Foundation and Plinth Beams and Similar Work; Square, rectangular or polygonal, Vertical or to batter, Flat, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Sides of Pillars, Posts, Struts, Piers, Columns and Stanchions, Flat, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Faces of Walls, Retaining Walls, Abutments, Parapets and Similar Work including attached Pillasters, Buttresses, etc.; Vertical or to Batter, Flat, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Sides and Soffits of Floor or Roof Beams, Girders, Beam Haunchings, Bress-summers, Lintels, Cantilevers, Shelves including Supports, Overhangs, etc. also splays between Floors and Beams, etc., Flat, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Soffits of Suspended Slabs such as Roof Slabs, Floor Slabs, Landings and Similar Work; not exc. 200mm thick (Horizontal or Sloping), etc., Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Edges of Concrete Flats, Treads, Breaks in Floors, Window Cills, Openings in Concrete Walls, Floor and Roofs not exc. 20 Cm Wide and Sides of RCC/ PCC Bands in Walls, Horizontal or Sloping and Similar Work, exc. 10 Ccm but not exc. 20 Cm Wide, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Pre-cast Cement Concrete 1:3:6 (20mm graded stone aggregate) Block Masonry with Solid Blocks, exc. 10 Cm in width, Set in Cement Mortar 1:6, complete all as specified and as directed.

M&L Cutting Holes in Brick Walls, not exc. Half Brick thick, built in Cement Mortar for inserting of Holdfasts, Lugs, etc. and Making Good to dismantled portion with Cement Concrete 1:2:4 (20mm graded stone aggregate) or Cement Mortar 1:3 (as required) and adjoining Surfaces in Cement Mortar 1:4, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) in Scantling, Cleansawn, Timber fixed (Unframed work), fixing with Nails, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Plain Fillets, Wrought, Square, Rectangular or Triangular in Section, exc. 3.0 Sq Cm but not exc. 6.0 Sq Cm, fixed with Nails/ Screws (as ordered), complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Plain, Solid, Straight, Chowkats and Frame, Wrought, Framed rebated on the Solid, Rounded or Chamfered, put together with Glue pinned at Joints, complete all as specified and as directed.

S&F Flush Shutter 30mm thick, Solid Core Construction, with Block Board Core and Plywood Face Panels, Commercial type on Both Sides including Teakwood Lipping 6.0mm thick, fixed with Nails, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Glazed and Skeleton Shutter 35mm thick, Open rebated and prepared to receive Glass, Gauze, etc. (without Sash Bars), Edges of Framing plain, chamfered or rounded. fitted with cut and mitred Beads for securing glass, etc.; sizes of Members of Shutters as specified in SSR Part I, Section 8, Clause 8.24(a) and fitted to Chowkat, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Glazed and Skeleton Shutter 30mm thick, Open rebated and prepared to receive Glass, Gauze, etc. (without Sash Bars), Edges of Framing plain, chamfered or rounded. fitted with cut and mitred Beads for securing glass, etc.; sizes of Members of Shutters as specified in SSR Part I, Section 8, Clause 8.24(a) and fitted to Chowkat, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Glazed and Skeleton Shutter 30mm thick, Divided into Squares, with plain, chamfered or rounded, mitred and rebated Sash Bars to receive Gauge/Glass, any numbers, sizes of Members of Shutter as specified in SSR Part-I, Section 8, Clause 8.24(b) and fitted to Chowkat, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Small Fittings such as Brackets of any type, Latch and Hinge Blocks, Shaped Door and Window Stops and the like, including all necessary Labours; Articles not exc. 200 Cu Cm Each, complete all as specified and as directed. NOTE : Stainless Steel Butt Hinge will be Measured and Paid under appropriate Item as 'supply only'.

S&F Aluminium anodised Barrel Tower Bolt 125mm long (as approved), Extruded Section, complete all as specified and as directed.

S&F Aluminium anodised Barrel Tower Bolt 200mm long (as approved), Extruded Section, complete all as specified and as directed.

S&F Aluminium alloy, anodised, Sliding Door Bolt 300mm long with Hasp, Staple (Bolt type) and Fixing Clips of Sheet, Cast or Extruded Sections and Fixing Bolts and Sliding Bolts of Extruded Sections or Cast-Aluminium alloy and fixed, complete all as specified and as directed.

S&F Stainless Steel Butt Hinge 50mm in size (as approved), complete all as specified and as directed.

S&F Stainless Steel Butt Hinge 75mm in size (as approved), complete all as specified and as directed.

S&F Stainless Steel Butt Hinge 100mm in size (as approved), complete all as specified and as directed.

S&F Aluminium Handle 125mm (as approved), Fabricated type, anodised, complete all as specified and as directed.

S&F Aluminium Handle 150mm (as approved), Fabricated type, anodised, complete all as specified and as directed.

S&F Mild Steel 300mm, Ordinary Rat Tail Rod pattern Springs including Roller and Roller Plate, complete all as specified and as directed.

S&F Floor Door Stopper (as approved) having Overall Length of Cover Plate 150mm of Aluminium Alloy Body and Tongue, anodised, with Hard Drawn Steel Spring, fixed in Floor, complete all as specified and as directed.

S&F Stainless Steel Drapery Rods (Curtain/Harrison Rails) having 24mm Outer dia, fixing with and including Brackets, Stops, Rollers, Side Holders, etc., and Fixed-in-repairs, complete all as specified and as directed.

S&F Stainless Steel Wire Cloth 0.36mm nominal dia of Wire and average width of aperture 1.40mm and fixed with Stainless Steel Wire Staples, complete all as specified and as directed

S&F Stainless Steel Wire Cloth 0.36mm nominal dia of Wire and average width of aperture 1.40mm and fixed with Stainless Steel Wire Staples and Fixed-in-repairs, complete all as specified and as directed.

S&F Sheet Glass 3.0mm thick, Plain, Ordinary quality and Glazing with Oil Putty in Square not exc. 0.50 Sqm in Each Pane, complete all as specified and as directed.

M&L TMT Bars 10mm dia and Over, cut to length, bent to shape required including cranking, bending spirally for hooping for Columns, hooking Ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L TMT Bars 8mm dia in Stirrups, Spacers and Binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L Mild Steel Round Bars 10mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping for Columns, hooking Ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L Mild Steel Framed Works such as Grills, Gratings, etc. with Ends of Bars shouldered and/or riveted or forged into Spikes; Framed Guard Bars; Barred Iron Doors; Ladders; Framed Balusters; Walkways; Railings; Framework of Water Tanks and similar Work, conforming to Fe-290, Gde-E-165, complete all as specified and as directed.

M&L Mild Steel Bands, Straps, Supports or Stays for Rainwater, Ventilating Pipes including Bolts, Hooks (Stay) for large Gates; Hook and Pintle Hinges: large Hasps and Staples; Hand Made Sliding Bolts; Clamps; Holdfasts; Wall Ties and similar small Articles conforming to Fe-290 Gde-E-165, complete all as specified and as as directed.

M&L Steel Work (Square/ Rectangular Hollow Section) in Tublar Trusses including Special Shaped Washers, etc. complete using ERW or Induction Butt welded Tubes, confirming to IS:0011-1979, Grade St-240, complete all as specified and as directed.

M&L Plates (Plain or Chequered) Channels, Square cut or notched (Ordinary and Counter Sunk) forming Holes, without any attachment, conforming to Gde Fe-410-W (Gde E-250) Quality 'B', complete all as specified and as directed.

M&L Mild Steel Screw Bolts (machine made) of any description or size, with Hexagonal or Square Heads at One End and screwed the Other End, or screwed Both Ends, Each screwed End to be fitted with Washers and One Hexagonal or Square Nut, complete all as specified and as directed.

M&L Running Welding in Repairs in Steel Works, thickness of metal to be welded not exc. 6.0mm, complete all as specified and as directed.

S&F Corrugated Mild Steel Sheeting 0.63mm thick, Galvanised @ 275 Gram per Sqm, with Two Corrugation Side Lap, fixing with and including L-type or J-type Cranked Hook Bolts with Washer, etc., complete all as specified and as directed.

Re-fixing only Corrugated Mild Steel Sheeting (Serviceable Sheets obtained from Item No. 1.007 here-in-before) with Two Corrugation Side Lap, fixing with and including L-type or J-type Cranked Hook Bolts with Washer, etc., complete all as specified and as directed.

S&F Plain Mild Steel Sheeting 0.80mm thick, Galvanised @ 275 Gram Per Sqm, in Ridges, Hips, Valley Gutters, etc., fixing with and including L-type or J-type Cranked Hook Bolts with Washer, etc., complete all as specified and as directed.

Refixing only Plain Mild Steel Sheeting 0.80mm thick (except Sheets, Serviceable Sheet obtained from Item No. 1.007 here-in-before) in Ridges, Hips, Valley Gutters, etc., fixing with and including L-type or J-type Cranked Hook Bolts with Washer, etc., complete all as specified and as directed.

S&F HSPC Non-Asbestos Fibre Building Boards 4.0mm thick, Plain and fixing to Timber Frame Work with Screws, complete all as specified and as directed.

S&F Plywood Board 6.0mm thick, Grade BWR, Type BB, fixing with Mild Steel Screws to Timber Frame Work as in Walls, etc., complete all as specified and as directed.

M&L Cement Concrete 1:4:8 (40mm graded stone aggregate) 75mm thick in Sub-base to Flooring, etc., finished Concrete Surfaces Fair and Even, complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (20mm graded stone aggregate) 50mm thick in Floors, etc., finished Concrete Surfaces Even and Smooth with Using Extra Cement, complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (20mm graded stone aggregate) 40mm thick in Floors, etc., finished Concrete Surfaces Even and Smooth with Using Extra Cement, complete all as specified and as directed.

S&F Glass Dividing Strips 3.0mm thick, Width of Strips 38mm and inserted in Position, conform to design, complete all as specified and as directed.

M&L Roughening Surfaces of Old Concrete Floor by Picking, Sweeping Clean and Washing down with Water to remove Dust, etc., and Brushing with Neat Cement Slurry @ 3.0 Kilogram per Square Metre on Cleaned Concrete Surfaces, complete all as specified and as directed.

M&L Non-Skid Ceramic Coloured Tiles 7.0mm to 8.0mm thick (Square/ Rect-angular) Area of Each Tile exc. 0.11 Sqm but not exc. 0.18 Sqm (1st quality) in Floors, Jointed in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, laid over and including Screed or Screed Bed 15mm thick in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate

M&L Non-Skid Ceramic Coloured Tiles 7.0mm to 8.0mm thick (Square/ Rect-angular) Area of Each Tile exc. 0.18 Sqm but not exc. 0.38 Sqm (1st quality) in Floors, Jointed in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, laid over and including Screed or Screed Bed 15mm thick in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate

M&L Non-Skid Ceramic Coloured Tiles 7.0mm to 8.0mm thick (Square/ Rect-angular), area of Each Tile exc. 0.11 Sqm but not exc. 0.18 Sqm (1st quality) in Vertical Surfaces i.e. Dado, Skirting, etc., set in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, fixing over and including Screed Bed 10mm thick in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate

M&L Glazed Ceramic Coloured Tiles 300x200x6.0-7.0mm thick (1st quality) in Vertical Surfaces i.e. Dado, Skirting, etc., set in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, fixing over and including Screed Bed 10mm thick in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate

M&L Machine cut Kota Stone Slab Flooring 20-25mm thick, Over and including Cement Screed Base in 15mm thick in Cement Mortar 1:6, laid in Floor and jointed with Grey Cement Slurry mixed with Pigment to match the Shade of the Slab including Rubbing and Polishing, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate

M&L Machine cut Kota Stone Slab 20-25mm thick, Over and including Cement Screed Base in 10mm thick in Cement Mortar 1:4, laid in Riser of Steps, Skirting, Dado and Pillar and jointed with Grey Cement Slurry mixed with Pigment to match the Shade of the Slab including Rubbing and Polishing, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate

M&L Machine cut Granite (of any type) Tiles 20mm thick, Over and including Cement Screed Base in 15mm thick in Cement Mortar 1:6, Bedded and Jointed with Grey Cement and Pointed with White Cement with Admixture of Pigment to match the Shade of Granite Stone including Grinding and Polishing, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate

M&L Cement Concrete 1:3:6 (20mm graded stone aggregate) 75mm thick in Plinth Protection, etc., Laid in Alternate Panels, finished Concrete Surfaces Even and Smoooth without Using Extra Cement, complete all as specified and as directed.

M&L Rendering 10mm thick in Cement Mortar 1:6 on Brick/ PCC Blocks or Concrete Works, finished Plastered Surfaces Even and Smooth without using Extra Cement, complete all as specified and as directed.

M&L Rendering 15mm thick in Cement Mortar 1:4 on Brick/ PCC Blocks or Concrete Works, finished Plastered Surfaces Even and Smooth without using Extra Cement, complete all as specified and as directed.

M&L Rendering 15mm thick on Bricks/PCC Blocks consisting in 2 layers, Backing/Under layer of 10mm thick in Cement Mortar 1:6 and Float/ Top layer 5.0mm thick in Cement Mortar 1:4 including mixeing WPC to Float/ Top layer, finished Fair and Even, complete all as specified and as directed. NOTE : Water Proofing Compound (WPC) will be Measured and Paid saperately under appropriate Item.

Supply only Water Proofing Compound (as approved), conforming to IS:2645-2003, complete all as specified and as directed.

M&L Preparing Newly Plastered Surfaces of Walls and applying Three Coats of White Wash, complete all as specified and as directed.

M&L Preparing Old Treated Plastered Surfaces of Walls and applying One Coat of White Wash, complete all as specified and as directed.

M&L Preparing New Non-Asbestos Fibre Building Boards Surfaces of Ceiling and applying Three Coats of White Wash, complete all as specified and as directed.

M&L Preparing Old Treated Non-Asbestos Fibre Building Boards Surfaces of Ceiling and applying One Coat of White Wash, complete all as specified and as directed.

M&L Preparing New Plastered Surfaces of Walls and applying a Layer of Wall Care Putty 3.0mm thick on Plastered Surfaces of Walls including Cutting and Rubbing down to obtain a Even and Smooth Surface, complete all as specified and as directed.

M&L Applying Two Coats of Distemper Oil Emulsion (as approved) over a Coat of Chalk Whitening (Priming Coat), complete all as specified and as directed.

M&L Preparing Old Treated Plastered Surfaces of Walls and applying One Coat of Distemper Oil Emulsion (as approved Tint), complete all as specified and as directed.

M&L Preparing Newly Plastered Surfaces of Walls and applying Two Coats of Cement Based Paint (as approved Tint) over a coat of Alkali Resistant Priming Paint, complete all as specified and as directed.

M&L Preparing Old Treated Plastered Surfaces of Walls and applying One Coat of Cement Based Paint (as approved Tint), complete all as specified and as directed.

M&L Preparing New Wooden Surfaces of any description, over 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade of approved Tint) over a Coat of Pink Primer, complete all as specified and as directed.

M&L Preparing Old Painted Wooden Surfaces of any description, over 10 Cm in Width or Girth and applying One Coat of Synthetic Enamel Paint (1st quality/ grade of approved Tint), complete all as specified and as directed.

M&L Preparing New Wood and Wood Based Surfaces of any description, Width or Girth not exc. 10 Cm and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade of approved Tint) over a Coat of Pink Primer, complete all as specified and as directed.

M&L Preparing Old Painted Wooden Surfaces of any description, not exc. 10 Cm in Width or Girth when unconnected with other Painting or when Painted in different Tint and applying One Coat of Synthetic Enamel Paint (1st quality/ grade of approved Tint), complete all as specified and as directed.

M&L Preparing Steel and Iron Surfaces of any descriptions, over exc. 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade of approved Tint) over a Coat of Red Oxide Zinc Chrome Primer, complete all as specified and as directed.

M&L Preparing Old Painted or Previously untreated Steel and Iron Surfaces of any descriptions, over exc. 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade of approved Tint), complete all as specified and as directed.

M&L Preparing Steel and Iron Surfaces of any description, not exc. 10 Cm in Width or Girth when unconnected with other Painting or when Painted in different Tint and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade of approved Tint) over a Coat of Red Oxide Zinc Chrome Primer, complete all as specified and as directed.

M&L Preparing Old Painted Steel and Iron Surfaces of any description, not exc. 10 Cm in Width or Girth when unconnected with other Painting or when Painted in different Tint and applying One Coat of Synthetic Enamel Paint (1st quality/ grade of approved Tint), complete all as specified and as directed.

M&L preparing New or Previously Treated Surface of Wood and Wood based Materials of any description and girth and treated with Two Coats of Creosote Oil, complete all as specified and as directed.

M&L Preparing previously Untreated Surfaces of Wood and Wood Based Materials, of any description and girth not otherwise described and treating with Tar or Coal Tar Black Paint to Backs of Chowkats, etc. Area tarred exc. 0.10 Sqm but not exc. 0.50 Sqm Each including Sanding with Clean Sharp Sand after tarred, complete all as specified and as directed.

M&L Preparing previously Untreated Surfaces of any description and girth not otherwise described and treating with Tar or Coal Tar Black Paint to Holdfast or similar Small Items, Area tarred not exc. 0.10 Sqm Each including Sanding with Clean Sharp Sand after tarred, complete all as specified and as directed.

M&L Preparing Newly Painted/ Treated Brick, Stone, Concrete, Asbestos Cement or Plaster Surfaces, Area not exc. 0.50 Sqm Each and applying One Coat of Synthetic Enamel Paint (Black/ Red or as approved Tint) as Base Surface Area for Writing Letters, etc., complete all as specified and as directed.

M&L Stencil Writing Letters or Figures (Block. Roman, Italic or Indian) of height exc. 150mm and not exc. 200mm with White Synthetic Enamel Paint over Black Base Surfaces, complete all as specified and as directed.

M&L Stencil Writing Stops, Commas, Short Lines, Dashes, Hyphens, Brackets, etc. with White Synthetic Enamel Paint over Black Base Surfaces, complete all as specified and as directed.

S&F Galvanised Steel Tubing 15mm bore (dia), medium grade, conforming to IS-1239 with all Fittings, fixed to Walls, Ceiling or laid in Floors, complete all as specified and as directed.

S&F Bib Tap 15mm bore (dia), Cast Copper alloy, screwed down, high pressure, with Crutch or Butter-fly handle, screwed both Ends for Iron Pipe or for Unions, complete all as specified and as directed.

S&F Angle Valve 15mm bore (dia), Cast Copper alloy, Chromium Plated, screwed down, high pressure, with Crutch or Butter-fly handle, screwed both Ends for Iron Pipe or for Unions, complete all as specified and as directed.

S&F Stop Cock 15mm bore (dia), Cast Copper alloy, Chromium Plated, Fancy type with long Shank and Cup (Concealed type), screwed down, high pressure, with Crutch or Butter-fly handle, screwed both Ends for Iron Pipe or for Unions, complete all as specified and as directed.

M&L Rotational Moulded Polyethene Water Storage Tank 1000 Litre Capacity, Cylindrical, Vertical with Closed Top, 3 layered, conforming to IS:12701-1996, hoisted and fixed in Position all as specified in MES Schedule, complete all as specified and as directed.

S&F PTMT Ball Valve 20mm bore (dia), having weight not less than 210 Grams, high pressure with Epoxy coated Aluminium Rod and high density Plastic Ball, screwed for Iron Pipe, complete all as specified and as directed.

S&F Kitchen or Laboratory Sink made of Stainless Steel l.0mm thick of Overall size 495x420mm and Bowl size 410x330x160mm with 40mm (dia) Stainless Steel Waste Fitting, Strainer, Washers and Wastes, etc. including bedding in Cement Mortar to dwarf Wall or including fixing Cantilever Brackets and connecting Union to Pipes, complete all as specified and as directed.

S&F PTMT Grating Doom 100mm dia (minimum Weight 25 Gram) with Waste Holes (as approved), complete all as specified and as directed.

S&F PVC (SWR) 75mm bore (dia) Pipe, Single Socketed, in any length with Rubber Ring Joints, laid in Trenches or in Floors, complete all as specified and as directed.

S&F PVC (SWR) 110mm bore (dia) Pipe, Single Socketed, in any length with Rubber Ring Joints, laid in Trenches or in Floors, complete all as specified and as directed.

S&F PVC (SWR) Vent Cowl 75mm bore (dia), jointing with Solvent Cement, complete all as specified and as directed.

S&F PVC (SWR) 160mm bore (dia) Soil and Waste Pipe, single socketed, in any length with PVC/Rubber Ring Joints, with or without Ears, laid in Trenches, complete all as specified and as directed. NOTE : Necessary Earth Works will be Measured and Paid for separately under appropriate Items.

M&L Cement Concrete 1:3:6 (40mm graded stone aggregate) in Concrete Bed to PVC (SWR) 160mm bore (dia) including Packing Under and Haunching against the Sides of Pipes after they are laid and tested; complete all as specified and as directed. NOTE : Necessary Earth Works will be Measured and Paid for separately under appropriate Items.

M&L Cutting into existing Manholes for Connecting PVC (SWR) Pipes of 160mm bore (dia), Making Good to Pipe and rendering, cutting out existing Benching for and forming Branch Channel (½ Round or ¾ Section) in Cement Concrete 1:2:4 (20mm graded stone aggregate), Smooth Finished and Reforming Benching as required, complete all as specified and as directed.

E/M SERVICES/WORKS

M&L Taking down carefully Copper/Aluminium Point Wiring (Light, Fan, Socket or Power) complete from in any position including Fixture and Fittings such as Switches, Ceiling Roses, Pendants, Regulators, Sockets, Light Fittings, etc., Making Good disturbed surfaces of Walls/ Ceillings, etc. in Cement Mortar 1:3 including providing Surface Treatment (White/Colour Washing/ Distemper-ing/ Painting) wherever required to match the Existing Finishes, complete all as specified and as directed.

M&L Taking down/out unserviceable Sub-main Wiring from Batten/ Conduit/ PVC Casing Capping of any description, Making Good disturbed surfaces of Walls/Ceillings, etc. in Cement Mortar 1:3 including providing Surface Treatment (White/Colour Washing/ Distempering/ Painting) wherever required to match the Existing Finishes, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLS multi-stranded single core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLS multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE LIGHT/ FAN POINT controlled by One 1-way Switch 6 Amp, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLS multi-stranded single core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLS multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire for ONE 3/5 PIN SOCKET 6 AMP POINT on SAME BOARD, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLS multi-stranded single core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLS multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE 3/5 PIN SOCKET OUTLET 6 AMP POINT on INDEPENDENT BOARD, complete all as specified and as directed.

M&L Point Wiring with 4.0 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLS multi-stranded single core Copper Conductor Cable with 2.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLS multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE 3/5 PIN SOCKET OUTLET 6/16 AMP POINT on INDEPENDENT BOARD, complete all as specified and as directed.

M&L Sub-main Wiring with 2-Runs of 4.0 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLS multi-stranded Single Core Copper Conductor Cable and 1-Run of 4.0 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLS multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuty Conductor drawn through Concealed PVC Conduit of dia not less than 20mm, Medium grade, ISI Marke along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc., complete all as specified and as directed. NOTE :- (a) Cost of 3-Runs of Cables & 1-Run of PVC Conduit shall deem to be include in the Quoted Unit Rate and the same will be Mesured as ONE UNIT. (b) Sub-main Wiring will be measured PVC Conduit only. Wires required for looping, etc. as ordered will deem to be include in the Quoted UNIT RATE.

S&F PVC Casing Capping (ISI Marked) of size 25mm including all Fitting/ Fixtures such as Tee, Bend, Elbow, Socket, Saddles, etc., including Taking down/ out unserviceable PVC Casing Capping, complete all as specified and as directed.

S&F PVC Rectangular Block of size 350x300x50mm deep with 3.0mm thick Plastic Laminated Sheet Cover for mounting Swiches, Sockets, Fan Regulators, etc. including Taking down /out unserviceable Block of any descriptions, complete all as specified and as directed.

S&F Switch Piano 6 Amp, Single Pole, Flush type, 1-way, 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Socket Outlet 6 Amp, 5 Pin, Flush type, 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Switch Socket Combination 6 Amp 3/5 Pin & 16 Amp 3/5 Pin, Multi Plug, Flush type, 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Ceiling Rose 65x50mm, 3 Terminals, Surface Bakelite suitable for 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Angle Holder PVC/ Polycarbonate type with Back Plate suitable for Batten Fitting and connecting up, complete all as specified and as directed.

S&F LED Lamp 12 Watt, 230 Volt (as approved) including Taking down/out unserviceable Lamp of any description, complete all as specified and as directed.

S&F LED Light Fitting 1x20 Watt, T-8 with LED Tube Road 20 Watt, 4 Feet long, Complete and Connecting up with and including Twin Flexible Copper Wire of size 40/0.0076 having 0.50 Metre in length including Taking down unserviceable Light Fitting of any description, complete all as specified and as directed. MAKE : HAVELS, Cat No : LHEXBXPNIN1W020 or equivalent in Make : BAJAJ/ CG/ PHILIPS (as approved by GE).

M&L Taking down Ceiling Fan, Exhaust Fan of any Make, Size after disconnecting and Removing to AGE E/M Store Yard and deposited, complete all as specified and as directed.

M&L Opening Ceiling Fan body in presence of JE-in-Charge, Checking for Repair Works involving, Transporting Ceiling Fan 1200mm Sweep from AGE E/M Store Yard at ALONG to nearest Workshop, Taking out carefully burnt out Winding of any type from the Fan of any Make, Cleaning of Slots, Rewinding Fan Motor with Super Enamalled Copper Wiinding Wire of suitable Gauge and Weight (not less than 350 Gram) providing new Insulation Materials, Varnishing, Heating, Reassembling & Testing for Smooth Functioning after Rewinding, Removing the Fan to Site of Work after Rewinding, complete all as specified and as directed.

M&L Preparing Old Painted Surfaces of Fan including Cleaning, Washing, Rubbing and Filling Cavities with Filler, applying One Coat of Synthetic Enamelled Paint (as approved) with Spray Painting Machine and Writing MES No. with Black Paint, complete all as specified and as directed.

M&L Mild Steel Flat Iron 40x6.0mm Fan Hook, cut to length, bent to shape and drilling Holes, etc. as required, conform to Fe-290 Gde-E-165 including Mild Steel Bolts, Nuts, Washers, etc., complete all as specified and as as directed.

Supply & Hanging Ceiling Fan 1200mm Sweep, 230 Volt AC and connecting with and including suitable size Copper Conductor Cable from Ceiling Rose to Connector of the Fan, complete all as specified and as directed.

S&F Ceiling Fan Regulator, Rotary Stepped type, Electronic, 230 Volt AC including necessary Connection and connecting up, complete all as specified and as directed.

S&F MCB Single Pole 6 Amp to 32 Amp, 'C' Series, 50 Hz, 10 kA, 240 Volt and connecting up including Taking down/out unserviceable MCB, complete all as specified and as directed.

S&F MCB Single Pole & Neutral 10 Amp to 32 Amp, 'C' Series, 50 Hz, 10 kA, 240 Volt and connecting up including Taking down/out unserviceable MCB, complete all as specified and as directed.

S&F MCB Single Pole & Neutral 40 Amp, 'C' Series, 50 Hz, 10 kA, 240 Volt and connecting up including Taking down/out unserviceable MCB (if ordered), complete all as specified and as directed.

S&F MCB Distribution Board Sheet Metal Enclosure, Single Door with Steel Phosphotised Powder painted, SPN, 6-way, 240 Volt with 200 Amp rated Neutral Bars & Earth Bar and connecting up including Taking down/out unserviceable MCB DB, complete all as specified and as directed. MAKE : HAVELLS, Cat No. DHDPSHOSRW06 or equivalent Model in Make : LEGRAND/ L&T/ SCHNEIDER (as approved by GE)

M&L Earthing with Galvanised Earth Plate Electrode 600x600x6.0mm thick, buried directly in Ground vertically to a depth not less than 2.25 Metre below Ground Level with Top Edge of Earth Plate at depth not less than 1.50 Metre below normal Ground Level, connected to Galvanised Earth Lead Wire 4.0mm dia by means of Bolts, Nuts, Check, Nuts and Washers of Galvanised Iron or Steel and Earth Wire protected with and including GI Pipe 15mm bore (dia) Light grade, connected to Test Point upto 7.50 Metre away from Earth Electrode situated, Earth Plate surrounded by a packed thickness of Char Coal or Coke Dust mixed with Common Salt in alternate layers of not exc.150mm thick, PCC Pit in Cement Concrete 1:3:6 (20mm graded stone aggregate) and Pre-cast RCC Cover Slab of size 350x350x50mm in Cement Concrete 1:2:4 (20mm graded stone aggregate), reinforced with 10mm dia TMT Bars @ 100mm Centre to Centre in both ways, GI Wire Mesh, PGI Funnel with GI Watering Pipe 20mm bore (dia) Medium grade including necessary Excavation in Soft/ Loose Soil, Returning, Filling in and Removal of surplus Spoil upto a distance of 50.00 Metre and all as shown in Electrical Plate No. 3 of MES Schedule Part-I and Testing including Taking down/out unserviceable Earthing of any description, complete all as specified and as directed.

Excavating in Trenches, not exc. 1.50 Metre Wide and Depth not exc. 1.50 Metre for Taking out/up and/or Laying of Cables, Pipes, etc., Forming Surfaces to required Foundation, etc. and getting out as in Soft/Loose Soil, complete all as specified and as directed.

Returning, Filling in including Spreading, Levelling, Watering, Well Ramming in Layers not exc. 25 Cm, Providing Heaps along the Route of the Cable, Pipe Line with Surplus Soil in Soft/Loose Soil, complete all as specified and as directed.

Supplying, Laying & Testing LT Under Ground Cable 1100 Volt grade, XLPE insulated, PVC sheathed, Heavy duty, Armoured with multi-stranded Aluminium Conductor all as per IS:7098 (Part-I)-1998 having Cross-sectional Area 10 Sqmm, 2 Core, laid in Trenches, Ducts or through Pipes, etc. including Taking out Old Unserviceable Cables, Protection Pipes/ Bricks or Pre-cast Concrete Cable Covers, etc., complete all as specified and as directed. NOTE : Earth Works, Protection Pipes/ Bricks or Pre-cast Concrete Cable Covers, etc. will be Measured and Paid separately under relevent Items.

M&L HDPE Double Wall Corrugated (DWC) High density Polythene Pipes of Outer dia 40mm and Inner dia 32mm, cut to length/size as per Site requirement having Corrugation on the Outer Wall and Plain Surface on the Inner Wall, confirming to IS:14930 (Part I & II) for Protection of Under Ground Cable/ in PCC with and including all Fittings as required at Site including Cutting Floor and Making Good the same to match the Existing/ Adjoining Surfaces, etc., complete all as specified and as directed. MAKE : REX POLY EXTRUSIONS (ELDREX) or equivalent (ISI marked). NOTE : The Cost of All Accessories for fixing of DWC Pipe along the Wall/ Roof/ Cable Trays shall deemed to be included in Quoted UNIT RATE.

Sunwin Energy and Infra Pvt Ltd

M/S A K BROTHERS

M/S SINGH TRADERS

M/s Purbanchal Suppliers and Contractors

M/s HALDER ENTERPRISE