C/O Type-IV and Type-ll Residential Quarters for HPPWD Staff at Sangrah Distt. Sirmour H.P. (SH Water supply and Sanitary installation work, retaining wall and Breast wall, earth filling, boundary wall with Gate)

Amount

Earth work in excavation for structures in all depths as per drawing and Technical specification of Ministery of Rural Development for rural roads August 2004 (Two thousand four) C-305-1(Clause-three hundred five point one) including setting out construction of shoring and bracing, removal of stumps and other deleterious materials including dressing of sides and botttom and back filling in tranches with excavated suitable materials all work of rock cutting by blasting shall be carried out by taking all necessry precaution against soil erosion damages to hill side water pollution etc. and to protect stability of hill side rock shall be excavated with chiesling and wedging out rock (where blasting is prohibited) all earth work in cutting.excavation including rock excavation shall be carried out true to lines grades,side slopes, width, camber super elevation and level as shown on the drawings or as directed by the Engineer-in-Charge hauling and stacking of materials useful for construction at suitable sites and safe disposal of unsuitable cut materials by all modes of transportations in all leads and lifts at specified places, in specified manner systemathically with due consideration to avoiding adverse effects on environment, trimming filling of unevenness blind age and finishing of the road to specified dimension to the entire satisfaction as directedby the Engineer-in-charge. If the foundatioin of the structure is in an area with stangnat water or water is met with in the excavation due to spring seepage rain and other courses it shall be remove by suitable diversion boilingout or pumping as directed and the area of foudation or embankment shall be kept dry any loss to the public or private property during the course of excavation shall be the sole responsibility of the contractor which shall have to be duly compensated by him at his own cost in all cases.

Providing and laying concrete for plain/reinforced concrete in open foundations complete as per drawing and technical specification clauses 802, 803, 1202 and 1203 PCC.Grade-M-10 nominal mix 1:3:6 ( one cement : three sand: six graded stone aggregates including all leads,lifts and carriage of materials complete as per entire satisfaction of the Engineer in charge.

Providing and laying concrete for plain/reinforced concerete in open foundations complete as per drawing and technical specification clauses 802,803,1202 & 1203,(1:4:8 , 40 mm nominal size)as per HP.PWD specification 1990 volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts as per entire satisfaction of Engineer in charge.

Providing weep holes in brick masonry/stone masonry, plain/reinforced concrete abutmen,t wing wall return wall with 100mm dia PVC pipe extending throught the full width of the structure with slopes of 1(V):20(H) towards drawing face complete as per drawing and technical specification clause 614,709,1204.3.7 .as per HP.PWD specification 1990 volume-I, including carriage of all labour equipment and material to various location through all modes of transportation in all leads and lifts as per entire satisfaction of Engineer in charge.

Back filling behind abutment ,wing wall and return wall complete as per drawing and technical specificaition clause 1204.3.8 (One thousand two hundred four point three point eight) Granular material including all leads,lifts and carriage of materials as per HP.PWD specification including hauling of material in all leads, lifts as per the entire specification and direction of Engineer-in-charge

Demolition of brick work above G.L.upto upto floor two level including stacking of serviceable materials and disposal of un-serviceable materials within 20 metres lead.as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer-in-Charge

Extra over item No. 20090000 and 20110000 for removing mortar from and cleaning bricks including removal of rubbish within 20 metres lead brick work in cement mortar Per 1000 Nos bricks X2627 i.e 2627/1000=2.627 brick work in cement mortar.

Demolition of below G.L.upto 1.50 Metres depth and disposal of unserviceable materials within 20metres lead.as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer-in-Charge

Un-reinforced cement concrete upto 15 cm.thickness

Providing mild steel/Tor steel reinforcement for R.C.C work including bending,binding and placing in position complete upto floor two level Tor steel.as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer-in-Charge

Providing and laying cement concrete work 1:1.5:3 (1 cement : 1.5 sand : 3 graded stone aggregate 20 mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in.as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer-in-Charge

Wall (any thickness but not less than 0.1 m thickness) attached pilasters,buttresses,plinth and string courses etc.from top of foundation level upto floor two level: Lintels,beams,girders,bressumers and cantilevers upto floor two level.

Suspended floors, roofs, landing and shelves and their support, balconies, beams, girders, bressumers and cantilever upto floor two level.

Providing form work with steel plates 3.15mm(three point one five millimetre) thick welded with angle iron in frame 30x30x5mm(Thirty into thirty into five milimetre) ,so as to give a fair finish including centring ,shuttering ,strutting and propping etc. with wooden battens and ballies , height of propping and centring below supporting floor to ceiling up to all heights and removal of the same for insitu-reinforced concrete & plain concrete work ,as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment , plants and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge.

Sides and soffits of beams,beam haunchings,cantilevers, bressumers and lintels not exceeding 1mtr.in depth in all heights from floor.

Flat surfaces such as soffits of suspended floors, roofs, landings and the like :-Floors etc.upto 200mm.in thickness

Edges of slabs and breaks in floors and walls under 20cm wide

Providing and laying Second class Brick work using common burnt clay building bricks in superstructure above plinth level upto all floor levels in cement mortar 1:6 (1 cement : 6 sand) ,as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment, plants and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge.

Providing and laying Half brick work using common burnt clay Second class building bricks in superstructure upto all floor levels in cement mortar 1:4 (1 cement : 4 sand) ,as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment , plants and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge.

6mm cement plaster in ceiling in all floor level with cement mortar 1:3 (1 cement : 3 sand) as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment, plants and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge.

15mm cement plaster in single coat on the rough side of brick/concrete/stone walls for interior plastering upto all floor level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80 mm in girth and finished even and sand smooth in cement mortar 1:6 (1 cement : 6 sand) ,as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment, plants and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge.

15mm cement plaster single coat on fair side of brick/concrete/stone walls for interior and exterior plastering upto all floor level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80 mm in girth and finished even and smooth in Cement mortar 1:6 (1 cement : 6 sand) ,as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment, plants and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge.

Distempering two coats with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surfaces even and sand papered smooth.priming coat with distemper primer ,as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment,plants and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge.

Extra over item No17170000,17171000 and 17172000 for every sub sequent coat of distempering with oil bound washable distemper of approved brand manufacture.

Finishing wall with water proofing cement paint of approved brand and manufacture and of required shade on undecorated wall surfaces (Two coats) to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials.as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment,plants and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge.

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter sand papering and knotting ready mixed paint brushing wood primer pink ,as per HPPWD specification of 1990-Volume-I,including carriage of all labour, equipment, plants and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge.

Painting two coats (excluding priming coat) on new wood and wood based surfaces under coat with enamel and finishing coating with flat oil paint,brushing to give an even shade including cleaning of all dirt, dust and other foreign matters sand papering and stopping with paint other than white as per HP.PWD. Specification, including carriage of all labour equipment and material to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Painting two coats (excluding priming coat )on new steel and other metel surfaces with aluminium paint,brushing to give an even shade including cleaning the surface of the dirt, dust and other foreign matter.as per HP.PWD. Specification, including carriage of all labour equipment and material to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Steel work welded in built up sections, trusses and framed work, including cutting hoisting fixing in position and applying a priming coat of red lead paint including carriage of materials within all leads and lifts as per HPPWD specification of 1990-Volume-I,including carriage of all labour, equipment, plants and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge.

In gratings, framed, guards, bars ladders and railing, brackets and similar works :-

Providing and fixing anodised aluminium work for door,window,ventilators and partitions with extruded built up standard tubular and other sections of approved make conforming to lS 733 and lS 1285 anodised transparent or dyed to required shade according to lS 1868.(Minimum anodic coating of grade AC 15) fixed with rawlplugs and screws or with fixing clips,or with expansion hold fastners including necessary filling up of gaps at junctions,at top,bottom and sides with required PVC/neoprene felt etc.Aluminium sections shall be smooth,rustfree,straight,mitred and jointed mechanically where ever required including cleast angle,aluminium,snap beading for glazinge/panelling C.P.brass/stainless steel screws.All complete as per architectural drawings and the directions of Engineer-ln-Charges

For doors windows and ventilatiors and glazed partitions frames.

Ventilators including providing and fixing hinges/pivots and making provisions for fixing of fittings where ever required incluidng the cost of PVC/neoprene gaskets as required (fittings and glazing/panelling shall be paid for separately)

Providing and fixing glazing in a aluminium door,window,ventilator shutters and partition etc with PVC/neoprens gasket etc.complete as per the architectural drawings and the directions of engineer-in-charges (Cost of aluminium snap beading shall be paid in basic item)as per HP.PWD. Specification, including carriage of all labour equipment and material to various locations through all modes of transportation in all leads and lifts, including all incidental charges.

Glazing with glass panes of 4mm thickness(weight not less than 10.00 kg/sqm

Providing and fixing stainless steel wire mesh to existing aluminium frame complete as per arch drg and direction of Engineer-in-charge 4mm thick ,as per HPPWD specification 1990-Volume-1,including carriage of all labour,equipment and materials to various locations through all modes of transporation in all leads,lifts and other incidental charges.(AR)

Providing and fixing anodized aluminum sliding door bolt anodized colour and shade with bolts and nuts screws etc. complete,as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer in charge.

250 x16mm (Two Hundred fifty into Sixteen) millimeters size.

Providing and fixing anodized aluminium Tower bolts (barrel type) anodized transparent or dyed to required colour and shade with bolts & nuts screws etc. Complete,as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer in charge.

250x10mm(Two hundred fifty into ten) milimetres size.

150x 10 mm ( One hundred fifty into ten) milimetres size.

Providing and fixing aluminum handles anodized transparent or dyed to required colour and shade with bolts & nuts screws etc.complete,as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer in charge.

125 (One hundred Twenty Five)millimeters size

100 (One hundred) milimetres size.

Providing wood work in frames of doors,windows,clerestory,windows and other frames wrought,framed and fixed in position.2nd class deodar wood.as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer in charge.

Providing and Fixing pannelled glazed or panelled glazed shutters for doors windows and clerestory windows. Including black enammelled iron butt hinges with necessary screws, 40mm (Forty Milimetre) thick second class deodar wood as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer-in-Charge.

Providing and fixing wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm or doors, windows, clerestory windows including bright finished black enamelled iron hinges with necessary screws. 40 mm 2nd.. class deodar wood. as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer-in-Charge.

Cement concrete flooring 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) laid in one layer finished with a floating coat of neat cement including carriage of materials within all leads and lifts as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer-in-Charge.

40 mm thick

Providing and laying Duro stone vetrified tiles (300mmx300mmx10mm)in grey/coloured of approved shadein flooring,treads of steps and landing laid on a bed of 12mm thick cement mortar 1:3 (1Cement :3 Sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete.as per H.P. PWD.spesification 1990 volume - I, including carriage of all labour,equipments and materials to various location through all modes of transportation in all leads and lifts , including all incidental charges.

White glazed tiles 6 mm thick in skirting risers of steps and dado 12 mm thick cement mortar 1:3 (1 cement :3 sand) and jointed with cement slurry as per H.P. PWD.spesification 1990 volume - I, including carriage of all labour,equipments and materials to various location through all modes of transportation in all leads and lifts , including all incidental charges.

Providing and fixing 19mm thick Commercial Board water proof in shelves/box with but joint i/c fixing with nailsand screws etc.complete as per H.P. PWD.spesification 1990 volume - I, including carriage of all labour,equipments and materials to various location through all modes of transportation in all leads and lifts , including all incidental charges.

Providing and fixing 1.00 mm thick coloured or plain lamination sheet (sunmica) on board/ ply wood sheets with approved adhesive and nail etc. complete as per H.P. PWD.spesification 1990 volume - I, including carriage of all labour,equipments and materials to various location through all modes of transportation in all leads and lifts , including all incidental charges.

Providing and fixing square edges cover fillets (beading) 19 x 6 mm section i/c mitring at junctions with wood screws and nails complete. In 1st. Class indian teak wood as per H.P. PWD.spesification 1990 volume - I, including carriage of all labour,equipments and materials to various location through all modes of transportation in all leads and lifts , including all incidental charges.

Providing and fixing to wall ceiling and floor galvanised mild steel tubes(Medium grade) tube fitting and clamps including making good the wall,ceiling and floor as per H.P. PWD.spesification 1990 volume - I, including carriage of all labour,equipments and materials to various location through all modes of transportation in all leads and lifts , including all incidental charges.

15mm nominal bore

Making connection of galvanised steel distribution branch with galvanised mild steel main 20mm to 40mm nominal bore by providing and fixing tee including cutting and threading the pipes complete. ,as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment, plants and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge.

Providing and fixing Vitreous China padestal for wash basin complete recessed at the back for the receiption pipe and fittings. ,as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment, plants and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge.

Providing and fixing vitreous China wash basin with single hole for pillar tap with C.l. or M.S. brackets painted white including cutting holes and making good the same but excluding fittings :-(a) Circular 560mmx400mm(oval type under counter,as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer-in-Charge.

Providing and fixing C.P. Brass waste for wash basin or sink 32mm dia as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer-in-Charge.

Providing and fixing M.I. Union for wash basin or sink 32mm dia as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer-in-Charge.

Providing and fixing C.P. Brass waste for wash basin or sink 32mm dia as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer-in-Charge.

Providing and fixing 15mm dia (Fifteen milimetre)C.P Brass bib tap with Capstan head,as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment, plants and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge.

Providing and fixing 15mm(Fifteen milimetre) dia C.P Brass pillar tap with Capstan head,as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment, plants and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge.

Providing and fixing 15mm(Fifteen milimetre) dia C.P Brass stop cocks ,as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment, plants and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge.

Providing and fixing brass full way valve with wheel ,as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment, plants and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge.

15(Fifteen)mm nominal bore :-

Providing and fixing G.l./M.l Union of following sizes( Where not included in the items)as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment, plants and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge.

Providing and fixing stainless steel kitchen sink of approved standard lSl make with drain board and C.P.waste with C.l.or M.S brackets painted white including cutting holes and making good the same but excluding fitting.as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment, plants and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer Incharge

610x510mm with bowl depth 200mm

Providing and fixing PVC connection pipe with brass union including carriage of materials within all leads and lifts .(45cms length ):-

15mm nominal bore :-

Providing and fixing 100mm sand cast iron grating for gully,floor or Nahni trap as per HPPWD specification 1990-Volume-I,including carriage of all labour, equipment and materials to various locations through all modes of transportation in all leads,lifts and other incidental charges as per the direction of the Engineer-in-Charge.

Vikram Chauhan

JAI GOPAL SHARMA

BALBIR SINGH