Special Repair to Cat B-48 (Railway Police staff Quarter) at SRP Gr-05 Godhra Dist Panchmahal (Including Electrification) [1st Attempt]

In Figure In Words

Providing and laying cement concrete 1:4:8 (1- Cement : 4- coarse sand : 8- hand broken

stone aggregates 40 mm nominal size) and curing complete excluding cost of formwork in Rs. Two Thousand Six

1 (A) Foundation and Plinth 77.00 Cmt 2629.07 Hundred Twenty Nine

& Paise Seven Only

Providing and fixing pre-cast Rubber Dye/steel Dye interlocking concrete block

60mm thick with grade of concrete M-300 pnumatic compressed/vibrated mechanically

and as per approved design Confirming to IS15658:2006 including 35mm Sand layer for Rs. Six Hundred Eighty

2 levelling and filling the joint with sand in proper line and level as per guidlines of IRC : SP 1,017.00 Sqmt 680.10

& Paise Ten Only

63-2018 etc. Complete.

Providing and fixing pre-cast concrete kerb stone of gray cement based concrete block

30cm length,30cm height and 15cm thick of M250 grade concret as per approved design Rs. Three Hundred

3 and including excavation for fixing in proper line and level,filling the joint with C:M 1:3 178.00 Rmt 358.06 Fifty Eight & Paise Six

(1cement:3fine sand) etc complete. Only

P & F to Wall Ceilling and Floor SWR Rain Water pipe as Per IS-13592 of 90mm Dia

Complete with Special flings, Compressor type Fittings, Including G I slotted Z Patti (1.6

mm thick) with 6 mm dia U clamp with washer for vertical drain etc. including making

good the ceiling and floor on terrace rain water pipe shall be 90 mm Dia. SWR horizontal Rs. Three Hundred Two

pipe and vertical pipe and 90mm bend at the end near by Ground level rate are Inclusive & Paise Fifty Four Only

of all Necessary Fittings required.

Item Estimated Rate [Rs. Ps.]

Description of Item Quantity Unit Rs.

In Figure In Words

Providing and fixing to wall, ceiling and floor U.PVC/SWR soil waste pipe with 'O' ring

110mm dia of ISI 13592/92. Rate inclusive of all fittings like single or double "Y" with door,

reducer, coupler single T with door bend, pipe clip on wooden patti etc. complete and Rs. Four Hundred

5 making good the wall, ceiling and floor ISI make only joints shall be sealed by pipe 155.00 Rmt 471.36 Seventy One & Paise

sealant. Rate are excluding GI Slotted Z Patti ( minimum 1.6 mm thick) with minimum 6 Thirty Six Only

mm dia. etc. complete. (For 110 mm dia. Pipe.)

Providing and fixing to wall,ceiling and floor U.PVC / SWR soil waste pipe with 'O' ring

75mm dia of ISI 13592/92. Rate inclusive of all fittings like single or double "Y" with door,

reducer, coupler single T with door bend, pipe clip on wooden patti etc.complete and Rs. Two Hundred Forty

6 making good the wall, ceiling and floor. ISI make only joints shall be sealed by pipe 309.00 Rmt 245.74 Five & Paise Seventy

sealant. Rate are excluding GI Slotted Z Patti ( minimum 1.6 mm thick ) with minimum 6 Four Only

mm dia. etc. complete. (For 75 mm dia. Pipe.)

Finishing wall with weather proof exterior emulsion paint on wall surface (two coats) over

and above applying One Coat Of Primer to give an required shape even shade after

thoroughly brushing the surface to remove all dirt, and remains of loose powdered Rs. One Hundred Forty

7 materials.etc complete. Primer & Paint Shall be As per Approved brand of GSPHCL 3,341.00 Sqmt 147.68 Seven & Paise Sixty

material list for Any Height Eight Only

Cleaning manhole by removing sludge silt with the help of rope, brass etc. complete for

any depth of Man hole / I.C. Chamber Rs. Eighty One & Paise

Forty Only

Job work for cleaning of Existing Septic Tank with Vaccum Cleaning M/C. with all slug

removing from Septic Tank clean tank with water by Pressure Pump. Rs. Seven Thousand

Credit value for old G.I. Pipe of any dia meter and removed from site and clean site.

10 519.00 Rmt -12.00 Rs. Twelve Only -6228.00

Credit value for M.S. Grill and removed from site and clean site.

Rs. Sixteen & Paise

Fifty Only

Item Estimated Rate [Rs. Ps.]

Description of Item Quantity Unit Rs.

In Figure In Words

Dismentaling C I Pipe G.S.W Pipe abd A.C Rain water pipe with fitting and clamps

including stacking the material with all lead and lift(for any dia pipe) Rs. Seventy Two &

Paise Thirty Only

Providing , Fabricating and fixing M.S. GRILL/GATE of approved pattern fabricated from

M.S. flat, square bars, round bars, C-channel, Square/box pipe as per detail Drawings.

Rate is including welding with grinding and applying of mild steel putty with hardener

into groove to have smooth surface, two coats of Oil paint and one coat of yellow Zinc Rs. Seventy Five &

13 chromate primer coat of approved brand only oil paint shall be of brand & shade as per 1,618.00 Kg 75.12

Paise Twelve Only

Approved by GSPHCL & structural steel must be ISI make Only.

Providing and Fixing Granite of Telephonic Black Colour 15 to 18mm thick for jambs and

sills of doors & windows using neat cement slurry laid over 20 mm average base of

cement mortar 1:1 (1 cement:1 Coarse Sand) and jointed with grey cement slurry

including racking (Tancha Work) rubbing and polishing, scaffoldings, tools and tackles, Rs. Two Thousand Four

14 scaffolding etc. complete. (with base of neat cement) as per direction of Engineer in 26.90 Smt. 2428.00 Hundred Twenty Eight

charge including rounding the exposed edges as directed etc. Complete for ALL FLOORS. Only

Providing and fixing standared extruded of alluminium section of size 63mm x 38.10mm x

1.2mm @ Wt. 0.643 Kg/mt with colour anodized alluminium frame for ventilation with 5 Rs. One Thousand One

15 mm thick frosted glass as details etc complete for Ventilation 41.00 Smt. 1163.92 Hundred Sixty Three &

Paise Ninety Two Only

Provinding and fixing gun metal check or non return full way WHEEL HANDLE VALVE

mm dia. Rate are inclusive of all matreials, Labour Necessary Fittings etc. Complete as per Rs. Six Hundred Fifty

16 Detailed Drawings, Specification and as per the Instruction of Engineer In charge. All 4.00 Nos 656.86 Six & Paise Eighty Six

material used as per approved make list by GSPHCL Only

Provinding and fixing gun metal check or non return full way WHEEL HANDLE VALVE

mm dia. Rate are inclusive of all matreials, Labour Necessary Fittings etc. Complete as per Rs. Four Hundred

17 Detailed Drawings, Specification and as per the Instruction of Engineer In charge. All 8.00 Nos 416.47 Sixteen & Paise Forty

material used as per approved make list by GSPHCL Seven Only

Providing and fixing brass screw down stop tap.(A) 15mm dia. Rs. Two Hundred Three

18 30.00 Nos 203.79 & Paise Seventy Nine

Item Estimated Rate [Rs. Ps.]

Description of Item Quantity Unit Rs.

In Figure In Words

Providing & Fixing Floor drain jali (Glossy Finish) (on N.T.) of 6" X 6"size made of Stainless

Steel Grade 304 Floor Drain 3 Piece (Cover/Jali/Grating) With Anti Cockroach Bowl on Rs. Six Hundred

19 N.T. Rate are inclusive of all necessary fittings, material, labour etc.complete as per 96.00 Nos 613.97 Thirteen & Paise Ninety

direction of Engineer In charge. Seven Only

Provinding 10mm thick WATER PROOF cement plaster in single coat on fair side brick

work or concrete wall for interior plastering upto floor to level and finishing even smooth

in cemente mortar 1:3(1 cement:3 sand)finished with floting coat of neat cemente slurry Rs. Two Hundred Forty

20 incl. provinding and mixing water proofing materials in proportion recommended by the 123.00 Sqmt 248.54 Eight & Paise Fifty Four

manufacturers for All Floor. Only

Providing and Laying Acrylic base (Zycosil or equivalent) Water Proofing paint treatment

treatment in two coats of vertical and horizontal surface of depressed portion of Bath/W.C.

as directed by engineer in charge.This treatment shall be carried out over & above water Rs. One Hundred Ten &

proofing plaster. Paise Seventy Only

Suppllying and Filling Cinder in Sunk Portions for All Lead and Lift etc. Complete. Rs. Seven Hundred

22 16.00 Cmt 791.68 Ninety One & Paise

Sixty Eight Only

Providing CEMENT VATA( 10 cm x 10 cm ) size quarter round in cement mortar 1:1

including neat cement finishing, watering etc.complete Rs. Twenty Three &

Paise Forty Five Only

Providing and laying cement concrete 1:2:4 (1-cement:2-coarse sand:4-stone aggregates

20mm of nominal size)and curing etc.complete excluding cost of formwork in foundation Rs. Three Hundred

24 and plinth. 58.00 Sqmt 327.60 Twenty Seven & Paise

Sixty Only

Provinding & laying 24" x 24" vitrified ANTI KID 8mm thick tile flooring over 20 mm

(average) base of cement mortar 1:6 ( 1 cement: 6 coarse sand) on new surface or fixing

on existing flooring by adhesive material including dismentaling of existing flooring and Rs. One Thousand

material jointed with color cement slurry including finised with flush pointing & cleaning Three Hundred Eighty

25 the surface etc. size and shade of tiles shall be as per approved architecture drawing and 58.00 Sqmt 1383.99

Three & Paise Ninety

as per direction of engineer-in-charge for all floors Nine Only

Item Estimated Rate [Rs. Ps.]

Description of Item Quantity Unit Rs.

In Figure In Words

Providing& laying WHITE COLOURED GLAZED TILES in skirting, risers of steps and

DADO on 10mm thick cement plaster 1:3(1cement :3 coarse sand) & jointed with white

cement slurry. Tiles shall be of approved quality, size & colour.Size of Tiles Shall be 600 x Rs. One Thousand Four

26 300 mm.for size and shape of tiles shall be as per Approved Architectural Drawing & as 52.00 Sqmt 1403.33 Hundred Three & Paise

per Direction of Engineer Incharge Thirty Three Only

Applying rust convertor on exposed steel in bottom of slab and make the steel bar in

uniform shape etc. Complete s per direction of engineer-in-charge Rs. Thirty Eight & Paise

Thirty Only

Repairing of RCC Columns Lintel, chajjas etc. upto 10m height by providing & applying

Polymer Modified Plaster in Proportion 1:3 (Cement : Sand) with 10 lit. of SBR per bag of

cement in coats of 20mm thickness for the total thickness of 40mm incl. application of bond Rs. Four Hundred Fifty

28 1:1 (1 part Cement) on old concrete surface incl. scafolding curing cleaning etc complete 62.00 Sqmt 454.33 Four & Paise Thirty

Three Only

Dismentaling Existing Crack in Plaster in 'V'Shape up to brick masonary & Providing &

Finishing 'V' Groove with Cement Motor 1:1 (1 Cement: 1 Sand) with mixing Bonding Add.

Mixture & After finishing the Groove Provding & Applying Curing Compound Match with Rs. Sixty Four & Paise

Old Plaster work. Fifty Eight Only

Providing and fixing 4mm thcik bajari glass bended in putty with scrapping of existing Rs. Six Hundred

30 putty and glass in existing windows as directed by engineer in charge. 43.00 Sqmt 670.95 Seventy & Paise Ninety

Providing and fixing brass fixtures & fastening to door/window shutter[b] Tadi 10 mm x

200 mm as per sample approved BY EIC Rs. Seventy One &

Paise Ninteen Only

Drilling of 250 mm dia pilot bore hole in all strata by using mud-flush direct rotary ring by

using Bentonite powder. Rs. Eight Hundred Fifty

Seven Only

Supplying & Jointing of 200 mm dia PVC pipe 6kg per cm sq. perssure pipe of heavy duty

including slot of 5mX5mmX75mm as per IS 13452 with ISI Mark and Approved Brand of Rs. Four Hundred

33 GSPHCL. 50.00 Rmt 415.00

Fifteen Only

Meterial Charges used for the bore including labour and materials PVC bad plug having

length of 0.45 mt as ISI 200mm dia pipe Rs. One Hundred Fifty

Item Estimated Rate [Rs. Ps.]

Description of Item Quantity Unit Rs.

In Figure In Words

Reaming 200 mm dia pilot bore to 450 mm. dia hole including Assembling, Lowering

Housing, Casing strainer pipe, gravel packing etc.completed. From 200 mm dia to 450 Rs. Three Hundred

35 mm dia bore hole. 82.00 Rmt 395.00

Ninety Five Only

Geophysical survey for pin point for bore well including survey done by GSSWB

department with ralay repail of pin point location including fees to GSSWB department & Rs. Fourteen Thousand

36 Transporatation charges.. 1.00 Nos 14286.00 Two Hundred Eighty

Provinding and fixing water Closet Squatting (ORRISSA TYPE W.C. PAN ) size 580mm first

quality including necessary "P" or "S" trap, including jointing the trap with pan & soil pipe Rs. One Thousand Four

37 in viterous chine white colour, Joints shall be pipe sealent. 17.00 Nos 1004.00

Providing Supplying and fixing S4 Channel system (S4 Channel+Profilr Bracket+U Bolt

Rubber Mounted System) for multiple pipes for external vertical fixed line with wall Rs. Four Hundred

38 distance 3" including Nut, Bolt, Fastners etc complete as per details and as directed by 155.00 Nos 421.58 Twenty One & Paise

engineer in charge. Fifty Eight Only

Providing Supplying and fixing Single Pipe Bracket System with U Bolt Rubber Mounted

for Pipe Supporting Clamping system for external vertical Fixed line with wall distance 3" Rs. One Hundred

39 including nuts, Bolts, Fastner etc. Complete as per detailed specification and as directed 463.00 Nos 182.83 Eighty Two & Paise

by engineer in charge Eighty Three Only

Providing & fixing PVC SWR MULTI NANHI TRAP with Floor Drain 3 peace IS:14735 for

drain -100mm dia. With jali of following nominal dia. Of self cleansing design with C.I. Rs. One Thousand One

40 Screwed down or Hinged grating including the cost of cutting and making good the walls. 63.00 Nos 1122.26 Hundred Twenty Two &

Paise Twenty Six Only

Providing and fixing 24 mm thick THREE LAYER RIGID PVC PLAIN DOOR shutter with

Frame made from co-extruded three- layer rigid PVC foam sheet (single Extruded) with

density not less than 600 kg/cbm outer layer 1 mm thick should be of rigid PVC with Rs. Four Thousand Four

41 density of not less than 1400 kg/cbm manufactured by an ISO 9001-2015 certified 152.00 Sqmt 4476.00 Hundred Seventy Six

company. Complete as per direction of Engineer-in-charge, manufacturer’s specification Only

& drawing.

Item Estimated Rate [Rs. Ps.]

Description of Item Quantity Unit Rs.

In Figure In Words

Painting TWO coats (excluding priming coat) on previouslyprinted steel and other metal

surface with synthetic enamelpaint, brushing to give an even shade including cleaning Rs. Ninety Three &

42 thesurface of all dirt, dust and other foreignmatter 242.00 Sqmt 93.90

Paise Ninety Only

Providing and Laying 25mm thick Mirror Polished (Dimond Cut) Kota Stone Flooring over

20mm thick base of cement mortar 1 : 6 (1-Cement : 6-Coarse Sand) laid over and jointed

with grey cement slurry including Rubbing and Polishing etc. Complete as Directed By Rs. One Thousand Sixty

Engineer In Charge for all Floors. Six & Paise Ten Only

Dismentling doors, windows, ventilators etc. (wood or steel) shutters including chowkhats Rs. One Hundred

44 architraves, holdfasts and other attachment etc. complete and stacking them within all lead 96.00 Nos 181.13 Eighty One & Paise

and lift.(ii) Not Exceeding 3 Sq.M. in area. Thirteen Only

Credit Value For Door. (wood ) shutters including chowkhats architraves, holdfasts and

other attachment etc. Rs. One Hundred Fifty

Total Sch B-1 Civil cost Rs.

Electrical Item Discription

Providing and fixing Point wiring with 1.1 KV grade ISI marked approved make 2 x

sq.mm copper PVC insulated FRLS wire with 1.5 sq.mm (green) copper PVC insulated

FRLS wire for earth continuity in exiting FIA approved ISI mark white colour medium

class 20/25 mm dia. embossed rigid PVC pipe erected flushed on wall/ceiling complete

with company fabricated Metal Groove PVC fitting fixed with adhesive solution erected

On wall along with continuous G. I. fish wire to draw wires complete with approved make

5/6 Amp. tissino type switch and accessories mounted On Metal / PVC/Wooden Box

covered with 3 mm thick PC(Polycarbonate) /Acrylic/Laminated sheet. with necessary RS: Two Hundred

46A 30.00 Point 255.00

Lamp holder/ceiling rose / H.D.Connector as directed as directed for future extention , if Fifty Five only

required agency has to erect one higher size box & plate as per instruction of EIC. cost of

blank plate shall be paid as per tender itemFor Light Point-In existing medium class Rigid

PVC pipe and accessories erected flushed on wall/ceiling complete (Conductor

resistance should be as per IS:8130/1984 )

Item Estimated Rate [Rs. Ps.]

Description of Item Quantity Unit Rs.

In Figure In Words

For loop on switch board (with 6 Amp. Switch & 3/5 pin socket both having ISI Make)

RS: Sixty Six

46B 20.00 Point 66.00

Providing & Erecting Mains with FRLS PVC Insulated wire ISI marked 1.1 KV grade In

Existing FIA approved ISI mark medium class 20/25/32 mm dia. embossed rigid PVC

pipe with PVC fitting fixed with adhesive solution to be erected on/in brick wall / slab

along with continuous G. I. fish wire to draw mains laid in approved manner with

plastering by cement mortar & finishing the surface to match the wall / ceiling complete

RS: Forty Six

47A with FRLS PVC insulated wire for earth continuity. (Approved ISI make only) [a] 2 x 1.5 220.00 Mtr. 46.00

sq.mm. FRLS copper multi stranded conductor mains with 1.5 sq.mm. FRLS copper multi only

stranded conductor for earthing as per standard colour code.In Existing Pipe/casing

capping [Wire must be having box packing]

For 2 X 4.0 sq.mm. copper multi stranded conductor mains with 2.5 sq. mm copper multi

stranded conductor earthing as per standard colour code In ExistingIn Existing RS: Eighty Six

47B Pipe/casing capping [Wire must be having box packing] 110.00 Mtr. 86.00

Providing & fixing 25 mm. dia. PVC insulated G.I. corrugated Flexible pipe with necessary

socket, PVC bushes saddle, Check-nuts etc. complete of following sizes. RS: Twenty One

Item Estimated Rate [Rs. Ps.]

Description of Item Quantity Unit Rs.

In Figure In Words

Providing & Erecting 1.0 mtr long Earthing system by making minimum bore of 150 mm

dia in soft soil. Suitable for doing pipe-in-pipe technology earthing.Earthing electric rod

must be made from Corrosion free Hot dip galvanizing pipes having following

specification. Water must be poured in bore before starting earthing. Earthing value must

be measured with earth tester. Agency has to bring the earth resistance to at least 02 ohms

& voltage between neutral & Earthing upto 02 volt. Agency has to maintain earthing & its

value during defect liability. If required.

(A) Earthing Electrode Outer Pipe:- 88mm O.D, Outer Pipe wall thickness :- 2.6mm

minimum, Inner pipe:- 42mm O.D, Pipe thickness:- 2.5mm, Terminal Size:-

mmX100mm length, Zinc coating(Hot dip galvanising):- 75-100 micron, Nut bolt:- 2 no. RS: Five Thousand

49A with washer suitable for 14mm dia, total minimum Weight (approx) of earth electrode with 6.00 Each 5785.00 Seven Hundred Eighty

inside conductive material 26kg. Five only

(B) Inner chemical (CCM Compound)- Resistivity:- 0.2 ohm/ meter testing as per IEC

62561-2017, Voltage drop:- < 1 volt at no load & dry form, Sulphar content:- <2%

(C) Back fill Compound :-Earthing compound should be capable to retain moisture for

min.1year weight(appro.) of earth electrode with inside conductive material is 15 Kg.

Item Estimated Rate [Rs. Ps.]

Description of Item Quantity Unit Rs.

In Figure In Words

(D) Chamber and cover :-Earthing chamber should be size of 400mmX400mmX400mm

depth and Cover should be heavy duty cast iron with required size of

300mmX300mmX4mm thick.

Necessary test report must be submitted.

1. Short circuit test by ERDA/ CPRI for 25KA

2. Resistivity test of conducting material from NABL accredited lab.

3. Hot dip galvanised / zinc coating micro test from reputed laboratory.

4. General test report from OEM regarding specification of earthing.

{Make & Model to be approved by EIC) OEM has to submit all detail & sample for

approved before supplying

Water must be poured in bore before starting earthing. Earthing value must be measured

with earth tester. Agency has to bring the earth resistance to at least 02 ohms & voltage

between neutral &Earthingupto 02 volt. Agency has to maintain earthing& its value for one

year. If required. Earthing must be done in the presence of A.E (GSPHCL)

For Above Earthing ( 1mtr.) Additional charges for boring in semi hard soil & filling soft

soil in earth pit.(Certificate for soil have to given by DEE/AE along with Photographs).

RS: Two Hundred

49B 6.00 Each 276.00

Seventy Six only

Providing & Erecting Mains with ISI marked, 1.1 KV grade electrolyte multi stranded,

annealed copper conductor with heat resistant PVC insulated conforms to IS:694, IEC -

erected in existing pipe of following size (Specifically for control panel, relays, power

switchgears, motor starters & control wiring) with required size of copper lugs, nuts and RS: One Hundred

bolts if required. [f] One wire 16.00 sq. mm Forty One only

Item Estimated Rate [Rs. Ps.]

Description of Item Quantity Unit Rs.

In Figure In Words

Supplying and Erecting LED indoor fitting of approximately 4feet long with LED of wattage

0.2W to 0.5W assemble on single MCPCB with housing use as a heat sink shall be made

from Aluminum extrusion having enough strength (sample must be approved by EIC) with

polycarbonate diffuser with following specification:

(A) Company mark/name on the fitting.(B) Rated input voltage and frequency: 220V to

VAC ; 50Hz.(C) Rated input wattage: max. 24w(D) Rated input current : 0.2 Amp(E) Power

Factor : Min. 0.90(F) ATHD : Max. 15%(G) Rated Luminous flux: Min. 2420 lm(H) CCT:

6500K(I) CRI: Min. 80Ra(J) Driver Efficiency: Min. 80%(K) LED life span: Min. 50000 Hrs @

L70(L) Over Voltage protection: Withstand up to 440V/AC for 4 Hrs.(M) Surge protection :

Min. 2KV(N) IP rating: IP 20(O) IK rating : IK 02(P) Short circuit , Open circuit & Reverse RS: Three Hundred

Polarity Protection must be provided(Q) Fixing clamp design & strength should be Seventy only

sufficient to hold the fitting erected on wall or ceiling.(R) 3 core copper wire of

appropriate size with earthing connector

(Note:-The manufacturer/ authorized Channel partner of the manufacturer has to submit

5 yrs free replacement Guarantee for complete Fixture) [Approval will be given strictly

subject to item specification]

Supplying and Erecting 8 W LED Lamps with following wattage capacity of 220 to

voltage, minimum 15000 burning hours life, 500v in built- surge protection, Polycarbonate

diffuser , mounting suitable for E14 / E27 / B22 lamp holders, P.F >=0.5 (A) LED lamps RS: One Hundred

integral type with pc diffuser suitable LAMP holder. Eleven only

providing and erecting Polycarbonate body surface mounting LED Bulk type 9 watt

Lighting Fitting with electronic driver. And lumen output from luminaire 720lm , input

voltage range 90-300VAC , 50Hz cool white(3000 to 6500k), inbuilt driver, -20degC to RS: Seven

53 +60degC working temperature, AL frame with Beam Angle 120deg 3.00 Each 780.00 Hundred Eighty

Providing and erecting METALIC DANGER NOTICE BOARD for medium voltage

installation to be erected as per IS. RS: Sixty Nine

Item Estimated Rate [Rs. Ps.]

Description of Item Quantity Unit Rs.

In Figure In Words

Providing and erecting Medium Class FIA approved and ISI mark white colour

(embossed) RIGID PVC PIPES of following size complete erected with necessary PVC

fittings & Junction boxes fixed with adhesive solution & clamps on / in wall / ceiling along RS: Twenty Four

55 with continuous fish wire to draw mains with necessary fittings and junction boxes for 250.00 Mtr. 24.00

following dia. (a) 20 mm. dia.

Providing & erecting 240 V MCB Double pole switch for Motor and inductive load (C

curve) having 10 KA breaking capacity & confirms to IS:8828 in Existing M.S. box having

following capacity. For 40 Amp DP. Cat:-III (For Sump Room motor-if required) RS: Three Hundred

Twenty Seven only

Providing & erecting 415 V MCB Four pole switch for Motor and inductive load (C curve)

having 10 KA breaking capacity & confirms to IS:8828 in Existing M.S. box having RS: Seven

57 following capacity.(C) For 63 Amp FP. Cat:-III (For Sump Room GEB Cutout) 2.00 Each 730.00 Hundred Thirty

Supplying & fixing box for housing RCCB + MCB combination made of 18 SWG sheet steel

duly powder coated with gasket, dust & vermin proof bakelite shield two earthing RS: Two Hundred

58A terminals for following type of RCCB, RCCB + MCB [a] For 2 pole 3.00 Each 272.00

Seventy Two only

[b] For 4 pole

RS: Four Hundred

58B 2.00 Each 442.00

Forty Two only

Providing & laying HDPE Double walled corrugated pipes (DWC) of polyethylene

(conforming to IS: 14930 Part II) with minimum load required of 450N capacity with anti

rodent and ultra violet material properties with necessary connecting accessories of

same material at required depth to be laid 90 cms. under ground for laying of cable RS: One Hundred

59 below ground / road surface for enclosing cable and back filling the same to make ground 250.00 Mtr. 117.00

Seventeen only

as per original.For Outer dia. 50 mm and Inner dia. 38 mm (Test Certificate to be

Submitted)

Providing & Erecting 3 core 1.5 sq.mm. PVC insulated round copper wire ISI mark.

RS: Forty Six

Item Estimated Rate [Rs. Ps.]

Description of Item Quantity Unit Rs.

In Figure In Words

Providing and Fixing SITC of Outdoor aesthetically designed LED Street Light Luminaire

with total consumption of Max. 45 W with single piece die cast aluminium housing, high

power LED shall be mounted on high quality metal core PCB with extremely precison

designed heat sink complete with IP66 protection Class with polycarbonate / thoughened

glass cover the fixture should be suitable for pole/bracket mounting. The fixture to

comply both LM79 and LM 80 guidelines with LED module min. 130 lumen/watt with

toughen Glass L70 at 50,000 hrs, provided with high quality polycarbonate lenses for

better light distribution. The Fixture Should be able to be Pole Mounted and also bracket

mounted, provided with high quality driver for protection against high and low Voltage

cut Off, opertional for high amibient and high humid envirnoments, THD of driver should

be less than 10% and P.F > 0.95. Also the Fixture should meet the following technical

criterias Oprating range Voltage 120 to 300 V, system efficiency >= 110 lm/w, and total RS: Three Thousand

61 lumens not less then 4950, CCT > 5000K, CRI > 65, beam angle 120 deg, surge immunity 18.00 Each 3512.00 Five Hundred Twelve

level at least 10 KVThe Separate Potted driver should have over current, over voltage only

protection, short circuit protection so that the fixture recovers once the fault is removed. In

addition to the above product should be operational in the temperature range of 0 deg to

50 deg and humidity range of 10% to 90% RH. (GRE make GPH-SL-43W model, Lighting

Technology, Pyrotech make PAN-PE-11-P-43X0A model only) (Note:- The manufacturer /

authorized Channel partner of the manufacturer has to submit 5 yrs free replcement

Guarantee for complete Fixture)

For Street light Pole Bracket:Supplying and erecting street light pole bracket bracket

consisting of ISI mark "B" class G.I. Pipe 4.2 cm outside diameter complete with suitable B

class G.I. Sleeve tubing of 2 mm. thick and required size and approx. 45 Cms length

suitable for 76.5 / 80 mm. required size of pole top having nuts and bolts for fixing the

brackets and having spread of Upto 0.70 mtr. length with 110 deg. with vertical plane and

suitable welded stiffner reducer and nipple with check nut complete painted with one coat RS: Four Hundred

62 of red oxide and two coats of alluminium paint.(Zinc Coating before alluminium Paint is 12.00 Each 487.00

Eighty Seven only

mandatory) (a) Forsingle arm bracket. (Jindal / Asian / Tata / Surya Prakash make

Only) (Fabricators:- Ambica / Fab / Bajaj / Impression equipment Only) (Test

certificate to be submitted)

Item Estimated Rate [Rs. Ps.]

Description of Item Quantity Unit Rs.

In Figure In Words

Supplying and erecting Fabricating terminal box for street light pole made from 16 SWG

M.S. sheet having following size complete with fixing arrangement for terminal board,

with necessary hole for wire entry and exit from the box. The box shall be provided with

cover and hinges on one side and bolting at other end The box shall be fixed by clamps

fabricated from 25mm x 6mm flat.The box shall be painted with one coat of red oxide and

two coats of paint having following box size 330 mm x 260 mm x 140 mm (depth). And RS: Seven

Providing and fixing Terminal board of size 5.0 x 127 x 152.4 mm. bakelite sheet with 15 Hundred Two only

Amp. kitkat pattern porcelain fuse unit with suitable brass studs with nuts, washers and

clamps of size 25 mm x 3 mm suitable for pole painted with one coat of red lead paint.

Providing & fixing double compressed heavy duty flange type brass cable gland with

rubber ring for P V C insulated armoured cable complete with outgoing tails, insulating

RS: Fourty Eight

64 tape etc. For following size cables. (C) 2 to 4 core 10 Sq. mm (Sigma, MCI, Comet 25.00 Each 48.00

Make Only)

Providing And Erecting Solderless crimping type Copper lugs conforming to IS suitable

for cable of following size evenly crimped with high pressure tool & connected to

65 switchgear terminals with brass/cadmium plated nut bolts in an approved manner. For 50.00 Each 8.00 RS: Eight only

1.5/2.5 to 6 Sq.mm Cable

Solderiess crimping type Aluminium Lugs conforming to IS suitable for cable of following

size evenly crimping with high pressure tool & connected to switchgear terminals with

brass/ cadmium plate nut bolts in an approved manner.For 10.00 Sq.mm. Allumium Cable RS: Thirteen

Providing & erecting XLPE (IS : 7098) (I)-88 ISI marked armoured Aluminium conductor

cable for 1100 volt to be laid 90 cms. Under ground or to be laid on wall with suitable G.I.

RS: One Hundred

67 heavy guage cable clamp or in existing DWC pipe underground or road crossing or 324.00 Mtr. 139.00

Thirty Nine only

floor.(a) For 4 core x 10 Sq. mm

Providing & Erecting Univesal Astro interlligent Street light Control System insu with RS: Twelve

weather proof box for indoor allplication 5KVA ( as Per atteched Specification) Thousand Eight

Hundred Ninty Five

Item Estimated Rate [Rs. Ps.]

Description of Item Quantity Unit Rs.

In Figure In Words

Dismantling the existing light, fan, bell, independent plug point, wiring with mains of all

69 types along with accessories etc. complete and handed over to dept. 30.00 point 1.00 RS: One only

Dismantling the existing any type of indoor light fittings

70 20.00 Each 5.00 RS: Five only

Dismantling the existing ceiling fan / exhaust fan / cabin fan / bracket fan complete with

71 accessories, G.I. down rod, frame etc. and making the site clear. 13.00 Each 9.00 RS: Nine only

Total Electrical Amount (B)

Total Electrical Amount (A)

Total Civil + Electrical Amount (A) + (B) =

Executive Engineer

Signature of Contractor G.S.P. H. C.Ltd.