General repairs to Snow clearance machine Snow Cat 2013 and BACKHOE LOADER ESCORTS JK14G 5989 engaged for Snow Clearance Operation Patnitop Circular Road for the season 2026 27

Complete oil change of machine SNOW CAT 2013 i.e. engine oil-8 ltrs (10W30), Universal Tractor transmission Oil- ( 36 liters) , along with filter kit(Engine oil filter, fuel filter, Air filter). Complete job. The job includes cost of materials, fuel ltrs for the journey of the machine from Divisional Office Udhampur to Repair Workshop and then back after conducting the repairs and testing, etc. & labour charges. Complete Job.

Repairs to the cutting frame of the machine SNOW CAT 2013 by way of removal of old worn out cutting edges and then P/F and fabrication of cutting edges-02 no. of required length.Each cutting edge to be anchored with proper nuts and bolts (number as per requirement). Job also includes removing of minor bends of the frame by way of gas welding and other tools and tackles.Complete job

Complete Painting of machine SNOW CAT 2013 by way of scrapping its old paint and then painting of complete body, along with cutting blade with two coats of red oxide first and then two coats of décor paint and two coats on chassis and rims of four wheels with paint. The job include including letter writing, servicing greasing also. The job includes the cost of material, labour charges , tools and tackles required to execute the job.

Repairs to the electrical system of the machine SNOW CAT 2013 by way of removal of defective wiring and p/f pf new wiring complete and then replacing it with new ones, P/F of fuse box -01 no., wipe blade along with motor-01 set, head light assembly-02 no., rear light assy., -02 no. including LT wire of required length, insulation tape, cabin light switch and then testing of new circuit on load so as to ensure proper functioning of the auto-electric circuit of the vehicle. Complete job including cost of material, labour charges , tools and tackles required to execute the job.

Repairs to the clutch system of the machine SNOW CAT 2013 by way of Dismantling: the Drain steering hydraulic fluid. Disconnect high-pressure and return hydraulic hoses. Remove power steering cylinder, steering column linkage, Orbitrol control unit, tie-rod end joints, and front spindle kingpin assemblies from the front axle housing and then P/F Hydraulic Power Steering Pump Assembly, Steering Cylinder Repair Kit (Piston Seals, Rod Seals, O-Rings, Wiper Seals), Steering Control Valve / Orbitrol Unit Seal Kit,Steering Column Joint / Universal Coupling,honing/cleaning of hydraulic chambers, and fitment of new tie-rod ends and kingpin bushes and then Refitting all steering hydraulic lines, bleeding air from the hydraulic steering circuit, setting front-wheel toe-in/toe-out alignment, and pressure testing system for leaks under load.

Providing of new battery for SNOW CAT 2013of assorted rating ofstandard/reputed make 12V 88AH.Job also includes P/F of new terminals in place of old terminals and fitting of battery to the machines. Job is inclusive of transportation, cost of material, labour charges.

Repairs to the gear box of the tractor by way of extracting out old damaged parts and then P/F of new parts viz. gear sets, synchronizer cones, selector forks, bearings (needle roller and taper roller), circlips, and thrust washers, internal oil seals, O-rings, and gaskets with complete overhaul seal kits to prevent oil leakage and then Reassemble shafts, gears, and synchronizers followed by Realignment of transmission casing and ensure proper gear engagement across all ranges (high, low, reverse).Complete job

Periodic oil service of the machine BHL JKI4G 5989 by way of draining of M.oil and then P/F of M.Oil-18Ltrs. (15W40), M.oil Filter-01 no., Fuel Filter (Pry./Sec.)-01 set, Air Filter -01 no., Hydraulic oil )ISO VG 68) topping up -50 litresComplete job including labour charges , material, tools and tackles required to execute the job at site. Complete job

Repairs to cutting frame of the machine BHL JKI4G 5989 by way of removing the old damaged cutting edge and then P/F of fabrication of new cutting edge -1 no (material-MS) of length 8ft, thickness-20 mm. Each, cutting edge bolt with nuts -10 nos, removing of minor bends of frame and welding of cutting frame edge where ever found required. Complete Job

Repairs to the manual feed pump of the machine BHL JKI4G 5989 by way of Serviced and over-hauled low-pressure fuel hand priming pump assembly on machine by way of Draining low-pressure fuel line, dismantled primer barrel, cleaned non-return check valves, and replaced internal rubber O-rings, plunger seals, and banjo copper crush washers. Reassembled unit, bled air lock from fuel system via primary filter bleed screw, and torque-checked all line connections. Complete job