SPECIAL REPAIRS TO POWER HOUSE AND RADAR HEAD,BUILDING NO P-161,162 ALONGWITH PROVN OF PARKING SHED AND WASTE BIN ROOM FOR P-144 AND AIRMEN MESS AT AREA A AND AREA C AF STN WADSAR

Amount

M&L for complete removal of existing unserviceable water proofing treatment from top of roof and canopies/chajjas of building including removal of debris out side MD land all as directed.

Demolition of cement concrete (un-reinforced) of any description (including plastering,leeping etc) in any position not otherwise specifically provided for.

M&L for PCC (1:2:4) type B-1(using 20 mm graded crushed stone aggregate) as in padding of 50mm average thickness and in adequate slope on roof surface and finishing the top even & green and smooth all as specified and directed.

M&L for rendering 10mm thick in CM 1:4, mixed with WPC @3% by weight of cement on fair faces of concrete surfaces without using extra cement as in roof complete all as specified and directed. Note:- WPC shall be measured & paid separately.

M&L for 10mm thick screed bed in CM 1:3 mixed with WPT 3% by weight of cement all as specified and directed . Make:-STP/PIDILITE/TIKITAR

M&L for preparing clean and dried plastered surface and applying a coat of oil based bitumen primer conforming to IS 3384-1986 @ 0.30 litrs/sqm and then laying APP polymer modified membrane, 3mm thick with non woven polyster reinforced membrane (3.50 kg/sqm) having thermal insulation with white mineral gravel finish on upper side of membrane and laid by torch application method to the entire surface all as specified and directed by Engineer in Charge.

Supply only Integral waterproofing compound

Demolition of brick work of any description and in any position , built in cement mortar.

M&L for Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed.

M&L for Half brick work with fly ash bricks, straight or curved on plan to any radius built in half brick thick walls CM 1:4 all as specified.

M&L for PCC 1:3:6 Type C-2 (using 40mm graded stone aggregate) as in foundation filing,surface channel and drain etc complete.

M&L for PCC 1:2:4, Type B-1 (using 20mm graded stone aggregate) as in copings, cills, steps, bed plates, kerb and similar work including weathering, slightly rounded or chamfered angles and throating, as directed.

Taking down cement or cement lime plaster any description on brick or stone wall/ celling including raking out joint , hacking for key, scrubbing with water etc complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of concrete or block masonary CM 1:6 finished even and smooth (without using extra cement) in internal surface of wall complete all as specified and directed

Al as per item No 13.00 above but 10 mm tnick CM 1:6 and setting coat 5mm thick CM 1:4 mixed with WPC in external surface of wall including scaffolding complete all as specified and directed . Note:- WPC shall be measured and paid in revalent item of this schedule.

M&L for rendering 10 mm thick on fair faces of concrete or block masonary CM 1:6 finished even and smooth (without using extra cement) in internal surface of wall complete all as specified and directed

All as per item No 16.00 above but 5 mm thick in ceiling surfaces in CM 1:4 complete all as specified and directed

Taking out existing unserviceable plaster, loose unsound weaken cement concrete of any description and in any position from existing surface of RCC roof sab/RCC facia/ beams/ columns/ RCC chajja, average depth 25mm (approximate 6.5 mtrs height from natural GL) with power driven pneumatic chiesel and removal of debries upto a distence 500 mtrs out side MD land including saw cutting of all edges, making square shoulders of cavaties and roughening of smooth surface, scraping out and removing corrosion and all loose scales, rust etc from the visible reinforcement and cleaning the steel reinforecement properly providing NIT zink primer of FOSROC or equivalent. Zink primer of CHEMISTIC/WEBAC on visible reinforcement surface to form a contineous film and preparing the surface to recive concrete of epoxy grouting mortar etc all as specified including providing necessary scaffolding

M&L for applying bonding coat of modified styrene butadene emulsion (SBR bonding agent i.e nitobond SBR 45 , Fosroc, Pidilite or equivalent as approved) in proportion 1 Part (nitobond SBR 45:1 part (water) :3 part (OP cement) by volume with the brushes etc to bind new cement plaster/ polymer modified plaster/ concrete / screed concrete with oldsurface including removal of loose/ distengrated old concrete/ plaster including preparation of surface etc complete all as specified and as directed.

M&L for applying 25-35mm average thickness plaster on ceiling slab and chajja projections, facia and beams with polymer modified mortar firtified with SBR (Nitobond SBR 45 of FOSROC or equivalent of PIDILITE/ R or M International Mumbai/ 21 SHM mumbai) in proportion 1 part (cement):3 part (sand) by weight of cement with 11 to 15 ltrs water addition, finishing surface to match with existing adjoining surface complete all as specified and directed

Cleaning loose concrete if any all around reinforcement including from behind the reinforcing bars to give an average 15 mm thick (but not less than 10 mm clear air gap) and cleaning reinforcement of total rust using alkaline rust remover with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washed with water and allowing it to dry complete all as specified and as directed. (Note : - Length of reinforcement bars cleaned of rust all around shall be measured for payment.) (Note: thickness shall be measured excluding plaster)

Applying two coats of epoxy based passivating, protecting & bonding coat of zinc rich system (Nitozinc (R) primer of Fosroc and equivalent of SIKA/Dr Fixit Pidilite/ Krishna Conchem) as approved by the Engineer-in-Charge for old and new reinforcement any dia complete all as specified and as directed. (Note: Epoxy based passivating, protecting & bonding coat of zinc rich system shall be paid for separately).

S&F TMT bars 10mm dia and over in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with MS wire (annealed not less than 0.9mm dia) all as specified

M & L for mild steel TMT bars 5 mm dia and over in stirrups, spaces and binders, cut to length, bent to shape required, incl cranking, bending spirally for hooping for columns, hooking ends and binding with and incl mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed

Taking down loose material by chiselling, chipping from beam , stair, column, railing, pardi walls etc cleaning the surfaces and 30 mm thick guiniting in CM 1:3, including use and waste form work and providing welded wire mesh size 100 x 100 mm of wire 3, finishing the guiniting surfaces in cement mortar 1:3, 10mm with water proofing compound 2% by weight of cement and finishing even and smooth without using extra cement to match the existing all as specified and directed.

All as per item No. 25.00 above but for slabs / chajjas and thickness of guiniting 25mm and finished even and smooth with 5mm thick cement plaster 1:3 using water proofing compound 2% by weight of cement all as specified and directed.

M&L preparation of new surfaces of wall and applying two coats of cement base paint complete all as specified.

M&L preparation of new surface in ceiling and applying two coats of white wash complete all as specified and directed

M&L preparation of New surfaces of wall and applying Two coats of oil bound distemper over a coat of primer complete all as specified.

M&L preparation of old surfaces of wall and applying one coat of oil bound distemper complete all as specified.

M&L preparation of old decorated surfaces of ceiling and applying one coat of white wash complete all as specified and directed.

M&L for complete removal of existing treatment of wall surface and applying two coats of weather proof 100% acrylic paint over a coat of primer in old surface of wall and filling cracks with white cement etc complete all as specified and directed.

Dismantling of floor, hearth or wall tilling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc laid and bedded and pointed in any mortar.

M&L for 25mm thick PCC 1:2:4 type B-0 (12.5 mm graded aggregate) as in levelling course.

M&L for 15mm thick Screed bed or bedding layer of morter for laying floor finishes CM 1:6.

M&L for Non- skid Ceramic coloured tiles 7 to 8mm thick (square/Rectangular) area of each tiles exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed by Engineer-in- Charge.

M&L for Non- skid Ceramic coloured joint free tiles 7 to 8mm thick (square/Rectangular) area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 Sqm, (size of tile 600x600mm) in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified. Make:- Somany/ Johnson/Bells ceramic

M&L glazed ceramic coloured tiles size 450x300mm x 7mm thick in vertical surface etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including backing coat of 10mm thick in CM 1:4 etc all as specified and directed by Engineer-in Charge.

All as per item No 39.00 above but glazed ceramic tiles (size 600x100mm) in skirting including 10 mm thick backing coat of CM 1:4 all as specified and as directed.

M&L Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.

All as per item No 41.00 above but 15-18 mm thick kota stone flooring complete.

M&L for 15-18mm machine cut kota stone slab in single piece with round nosing with three numbers of serration as in treads of steps for staircase laid over and including 15mm thick screed bed in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of of the slab including rubbing and mirror polishing complete all as specified and as directed by EIC.

M & L for machine cut kota stone 15-18 mm thick (single piece in riser of steps), skirting, dado and window cills and jambs laid and jointed with grey cement slurry including cutting and mirror polishing over and including 10 mm backing coat in CM 1:3 complete all as specified and directed

Taking up or down 15mm dia steel tubing and connection including cleaning for refixing or removal to store all as directed.

All as per tem No 45.00 above but 20mm bore GI tubing complete.

All as per tem No 45.00 above but 25 mm bore GI tubing complete.

S&F 15mm dia Steel tubing medium grade Galvanised with all fittings and fixed complete to wall and ceiling or laid in floors all as directed.

All as per tem No 48.00 above but 20mm bore GI tubing complete.

S&F in repair vitreous china white wash down water closet pan(pedestal pattern) including fixing bolts,plastic seat cover with jet spray and including necessary flexible pipe connection complete all as specified and removing debris out side MD land.

S&F in repair PVC valveless, syphonic action type, flushing cistern, low level with inlet, ball valve ,float and handle including brackets.(The colour will also perfectly match with the EWC.)

S&F in repair Vitreous china white wash hand basin flat back of size 550 x400 mm including PVC waste pipe, PVC 15 mm dia 450 mm long with PTMT NUTS CONNECTION PIPE CP waste coupling including brackets cutting and pinning in ends of bracket complete.

S & F in repairs Bib taps, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed to 15mm bore pipe.

S&F in repair fancy type 15 mm dia CP stop valves (min weight 400 gm) cast copper alloy with crutch or butterfly handle both ends for iron pipe or for fixed union.

S&F in repair 15 mm bore pillar taps fancy type (min weight 400 gm) ,cast copper alloy ,with capstan head, chromium plated, screwed down, high pressure, with or without letters cold or hot with long shank and fly nuts screwed for iron pipe and fixed.

S&F Vitreous China Bowl Urinal flat back, size of 465x355x265 mm white (minimum), with grating and union for discharge pipe ( excluding flushing cistern, flush pipe and waste pipe )

S&F Health faucet (ABS) with rubit cleaning system 1.25m long PVC flexible tube & ABS wall hooh all as specified and as directed.

S&F in repair 75mm dia outlet CI nahani trap plain with S/S grating 150x150 mm including jointing with solvent cement as directed.

S&F Stainless steel grating with or without hole of size 150 mm.

S&F in repair PVC waste pipe of 32mm dia all as specifiede and as directed.

S&F SS soap dish of size 100mm all as specified and as directed by Engineer-in-Charge.

S & F in repair brass chromium plated tubular towel rail 20 mm dia 'D' type 60 cm long between flanges.

S&F in repair PVC water connection 600 mm long to wash basin of 15mm dia including CP nuts and washers all as specified and as directed by Engineer-in-Charge..

S&F in repairs rotational moulded polythene water storage tank (cylinerical vertical /square type with closed top) hoisted and fixed in position all as specified in SSR part-1 of 500 liters capacity all as specified and as directed.

All as per tem No 65.00 above but 750 Litre tank complete.

Taking down C I pipe including fittings of 100mm bore.

Taking down C I pipe including fittings of 75 mm bore.

S&F100 mm cast iron sand cast soil waist and vent pipe in any length with or without ears with cement joints fixed as directed.

All as per tem No 69.00 above but 75 mm pipe complete.

Refixing of 100 mm cast iron sand cast soil waist and vent pipe in any length with or without ears with cement joints fixed as directed.

All as per tem No 71.00 above but 75 mm pipe complete.

S&F cast iron bend 100mm bore (any radius) dimnishing pieces or tapers with oval access doors etc.

All as per tem No 73.00 above but 75 mm bend complete.

S&F 100 mm cast iron cowl

S&F 75 mm cast iron cowl

S&F 100mm bore Branch piece, single (equal or unequal ) ordinary or inverted (spigot or socket type) with parallel branches with oval access door.

All as per tem No 77.00 above but 75 mm bore branch piece complete.

Excavating in trenches, n.exc 1.5m wide and n.exc 1.5m in depth, for foundation etc or for shafts, wells etc n exc 10 Sqm on plan and nexc 1.5m in depth and getting out in soft/loose soil.

Removing excavated material n exc 50m depositing where directed at a level n exc 1.5m above the starting point.

Returning, filling in, including spreading, levelling, watering and well ramming in layers no exc 25cm in soft/loose soil.

Demolition and breaking up drain pipe SWG pipe set in cement mortar incl. Hunching and bed concrete for 150mm dia SWG pipe.

M&L for 150 mm bore SWG drain pipe, of grade 'A' laid in trenches and jointed all as specified and directed.

M&L for beding to drain pipes including packing under, and hunching in PCC 1:3:6 type C2 using 40 mm graded aggregate against the side of SWG 150mm dia pipes after they are laid and tested for following dia bore pipe all as specified and directed.

M&L for cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required for 150 mm bore pipe all as specified.

M&L for providing precast cement concrete 1:2:4 type B-1 (using 20mm graded aggregate) set in cement mortar 1:4 as in cover slab supported on wall complete all as specified and directed

S&F MS steel TMT bars 6mm to 8mm dia and over cut including 10mm dia cut to length ,bent to shaprequired including cranking bending for hooping for column ,hooking ends and bindings with and including mild steel wire (annealel)not less than 0.9mm dia.

Taking down chowkhats or frames with shutters( with out taking off shutters from the frame) n.exc 1.5 sqm each

Taking down chowkhats or frames with shutters( with out taking off shutters from the frame) exc 1.5 sqm but n.exc 4.00 sqm each

Taking down shutters of any description exc 1 sqm and n.exc 2 sqm each

S&F Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour square tube, supplying and fixing in opening as per specification and drawing.

S&F factory made solid panel PVC door shutter 30mm thick (Style)) consisting of frame made out of MS Tubes for top and bottom rail, MS frame shall covered with heat moulded PVC ‘C’ channel having a PVC sheet striped 20mm width strode inside with solvent cement rail and bottom rail on either side and as gap insert for top rail and bottom rail panting of predawn colored PVC sheets to be fitted in the MS frame welded/secured to the stiles and rails fathered at edges with suitable PVC sheet beading and jointed together with solvent cement supplying and fixing in the frame at the site as per specifications.

M&L for 30/32mm thick flush shutter , solid core construction, with block board core and plywood face panel,commercial type on both sides, kiln seasoned and chemically pressed treated and all as Specified and as directed by Engineer- in -Charge.

M & L for Aluminium doors, powder coated (of approved colour), with frame of section 100 x 44mm x 2.5mm thick and shutter with bottom rail of section 150 x 44.5 x 2.5mm thick, middle rail of section 85 x 44.5 x 2.5mm thick and top rail of section 80.4 x 44.5 x 2.5mm thick and styles of section 80.4 x 44.5 x 2.5mm thick with 5mm thick glass (plain/tinted/with laminated film) or prelaminated board fixed in position with aluminium beading including necessary rubber gaskets and 2 Nos. aluminium push plate handle of aluminium section 150mm wide and 2.5mm thick including 150mm aluminium tower bolt, brass mortice lock and hydraulic door closer complete all as per Drawing No. CEAA/TD/63 sheet No. 2.2 complete all as specified and directed.

S&F Aluminum powder coated grill fixed to walls with and including 'H' or 'F' aluminium channel of size 38 mm x 12 mm x 1.30 mm complete. Make:- Decogrille Cat No DG-107/ Jindal / Hindalco

Supply and fix Aluminium ventilator powder coated (requried colour to match window colour), louvers type, frame top & bottom of size 31x42x1.60mm (section No 20558) rectangular tub of size 40x20x2mm (section No 14019 and middle vertical of size 42x46.20x1.60mm Section (20560) and clip for fixing wire mesh and glass of size 19x17.30x0.90mm (section No 19360) thick including stainless steel wire cloth 0.36mm nomonal dia of wire and 1.40mm average width of aperture and fixed with stainless steel wire staples and supply and fixing 5mm thick glass louvers with blades of 100mm heavy duty with necessary rubber beading, gasket etc all as specified and as directed by Engineer-in-Charge. Make:-INDAL/JINDAL/ EVERLITE

M&L Aluminium partition powder coated made with aluminium section 38.80x1.80mm / 114.30x45.45x3mm section no. 4587 of jindal,national,Hindlco fixed in wall including provision for receiving glass pane etc and fixing the same with aluminium anodised beadind and rubber gasket including 5mm thick glass (black/tinted/plain) and all necessary fittings complete all as specified and as directed.

S&F aluminium alloy anodized sliding door bolt with haps and staple (bolt type) and fixing clip of sheet cast or extruted section or cast aluminium alloy and fixed length of bolt 300mm.

S & F 75 mm butt hinges, medium weight cold rolled stainless steel ISI marked.

S & F 100 mm butt hinges medium Weight, cold rolled mildsteel, and fixed

S & F aluminium anodised handle fabricated type of size 150mm.

S & F aluminium anodised barrel tower bolt of extruded section of size 150mm.

S & F aluminium anodised barrel tower bolt of extruded section of size 200 mm.

M&L for preparation of new wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified.

All as per item No 104.00 above, but one coat on old wooden surfaces except primer complete.

Taking down and refixing of 20mm steel tubing and connections in new or old position (walls, ceiling, floors etc)

All as per tem No 106.00 above but 25 mm bore GI tubing complete.

S&F in repair Fancy type CP angular cock 15mm dia cast copper alloy, chromium plated fency type screwed down high pressure with half turn type apstan/crutch heads, screwed both end for iron pipe or for unions and fixed. complete all as specified and directed.

S&F in repairs Vitreous china wash basin with pedestal flat back size 630X450 mm white, excluding taps, waste ,chain and plug and chain porcelain stopper but including brackets cutting for and pinning in ends of brackets or erecting stand.

S&F waste pipe LDPE of 32 mm dia for sink complete all as specified and directed

S&F waste coupling of 32/40mm dia brass CP for glazed ware sink basins, etyc with long screwed shanks and fly nuts fanges end bedded in red lead cement and other end fixed. complete all as specified and directed

S&F in repairs brass chromium plated shower roses 125 mm size with swivel joints, any size including fixing to 15mm bore steel pipe or union complete.

S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long all as specified and directed

S&F in repairs vitreous china wash down water closet pan semi- pedestal pattern (Anglo- Indian Type) with trap front or back inlet including seat cover of any pattern and health faucet (ABS) with rubbit cleaning system 1.25 m long, PVC flexible tube and ABS wall hook complete. Make :Cera /Hindustan/Parryware

S&F 100mm cast iron sanitary connection-short connection pipe of length upto 300-450mm socket to fit WC outlet etc.

All as per tem No 115.00 above but 75 mm sanitary connection complete.

S&F in repair stainless steel sink 1mm thick without drainage board for kitchen with plugs, washers and wastes coupling 40mm; including bedding in cement mortar to dwarf wall or including fixing into inside granite slab and including cutting of shape and size and connecting union to pipe overall size 495mm x 420 mm,bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed by Engineer-in-Charge. Make:- BELL (Imported) /Neelkanth/Neerali/Blue star

M&L for second class hardwood plain, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered put together with glue pinned at joints all as specified and directed.

S&F 18/19mm thick marine plywood (12Nos of ply) grade BWR, type BB fixed with screw to timber frame work or ply wood including Ist class HW fillets of bullnosed splayed, chamfered or rouned edge etc. exc 3 and n exc 6 sqcm. complete all as specified and directed Make:- Kitply/ Green or equivalent

M&L for decorative laminates of 0.9mm thick type 1, or matt finish, colour and pattern as approved by GE with adhesive complete all as specified and directed.

M&L for white laminates of 0.8mm thick glossy finish colour and pattern as approved by GE with adhesive complete all as specified and directed.

S&F aluminium anodised hasp and staple safty type with hinges pin including bolt to hinges plate and fixed with screws of size 100mm.

S&F CP decorative type brass handles 75mm long fixed to plywood or frame all as directed by Engineer-in- Charge.

S&F 80mm auto SS hinges of crank 0 degree to 90 or 180 degree, fixed with screws to plywood or frame work as per sample approved by EIC.

S&F stainless steel telescopic channel of size 450mm to 560mm of load per 45 kg/sqcm as per sample.

S&F Steel locking magnetic and connected plate to shutter and frame as per sample.

S&F cupboard knob brass polished 40mm dia fixed with screwed and washer of mild steel complete.

Taking down and refixing door shutter only of any description exc 1 Sqm n. exc 2 Sqm and resecuring or easing & adjusting of the shutter refixing in the same opeing etc complete.

M&L for 2nd class hard wood 35mm thick Plain framed, panelled shutter(two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both face.The size of rail and style as per IS:1003(Part-I), klin seasoned and chemically pressed treated and all as Specified and as directed by Engineer- in -Charge.

M&L for 35mm thick 2nd class hardwood glazed and skeleton shutter open rebeted and prepared to receive glass gauze etc (without shash bar ) edges of framing plain chamfered or rounded filled with cut and mitered beads for securing, glass etc size of member of shutter as per specified in SSR Part-I section 8,clause 8.24(a) supplyed and fitted to chowkats and directed by Engr-. in Charge.

S&F stainless steel wire cloth, 0.36 mm nominal dia. of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples all as specified and directed.

All as per item No 131.00 above, but fixed in repairs complete.

M&L Aluminium powder coated (powder coated of requried colour) three track sliding windows frame top & sides of size 92x31.75x1.50mm (section No 20831), bottom size 92x31.75x1.50mm (section No 20832) and shutter top & bottom of size 40x18x1.55mm (section No 20736) and sides (handle) of size 40x18x1.55mm (section No 20738) and lock side shutter frame of size 40x18x1.45mm ( section No 20737)" with rubber gasket, beading and locking arrangement and rollers etc including making good to the disturbed portion complete including stainless steel wire mesh 0.36mm nominal dia of wire with 1.40mm average aperture and fixed with stainless steel wire staples and fixing 5mm thick glass with necessary rubber beading gasket etc all as specified and as directed by Engr-in-charge. Make:-Indal/ Jindal/ Hindalco

M&L framed work such as grills, gratings, angle iron, purlin, wind tie etc. with end of bars shouldered and/or riveted or forged into spikes, framed guard bar , barred iron doors, railings, framed work/caging of water tank and similar works conforming to Fe 290, Gde -E-165 including hanging / locking arrangement as gate ,with hooks and pintle hinges, stops, hand-made sliding bolts including welding and fixing etc all as specified and directed.

S&F factory made solid PVC moulded door shutter, 28 to 30mme thick (stiles), with 2,4 or 6 raised panel designed with 4mm thick moulded PVC sheet on front face and 4mm plain colour PVC sheet on back face as per specification and drawing complete

S&F 150mm long Floor door stopper of brass body and tongue, with hard drawn steel spring, fixed to bottom of door shutter

M&L for granite work (of any type) 20 mm thick (table rubbed and polished) as in cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite etc all as specified and directed in Engineer -in -Charge.

M&L for preparation of new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide/ zinc chrome primer all as specified and directed.

All as per item No 138.00 above, but one coat on old steel surfaces complete.

M&L for preparation of new plastered surface of wall and applying two coats of distemper oil emulsion over a coat of primer over a sufficent coat of Birla wall putty.

M&L for complete removal of existing treatment of wall surface and applying two coats of distemper oil emulsion over a coat of primer over a sufficient coat of Birla wall putty in old surface of wall.

M&L for preparation of new plastered surface of ceiling and applying three coats of white wash all as specified.

M&L for preparation of old plastered surface of ceiling and applying two coats of white wash all as specified.

M&L for preparation of new plastered surface of wall and applying two coats of weather proof 100% acrylic paint over a coat of primer.

M&L for applying tack coat cold bituminous primer / industrial bitumen 85/25 @ 1.20 kg/ Sqm conforming to IS 3384 for fixing of laying APP polymer modified membrane complete all as specified and directed.

M&L for laying 3mm thick APP polymer modified membrane 3.0 to 3.5Kg/Sqm in weight with non-woven polyster reinforcement (mineral gravel finish on upper side of the membrane) and sealing all overlaps of 100mm in length side and 150mm on width side of membrane by torching the same as per manufacture instruction and all as per specified particular specification all as specified and directed . Make:-STP/PIDILITE/TIKITAR

S&F in repair harrison rails 28 mm dia aluminium anodised tubular drapery rod with and including side ball finials, matching rings made from high grade ABS plastics harrison rails bracket/holders suitable for each door and windows complete all as specified and as directed.

S&F 50mm dia bore pipe low density LDPE fixed to wall, ceiling or in floors etc

Cutting chases,in brick walls pinning in, making good to facing where required and pointing in cement mortar 1:3 to ends or edges of andings steps, cills sunshades, shelves lintels etc and cutting chases for concealed water tubing and making good cutting not exc 10 cm grith complete all as specified and as directed.

Excavating in post holes each nexc 0.5cum getting out in soft/loose soil, and removing surfaces soil to a distance nexc 50m and making good surfaces

S&F roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. Confirming to Fe 410 -W(Gde- E- 250) quality-A complete.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with shelf tapping screws as specified and directed.

Excavation over area n exc 1.5 mtr deep and getting out soft /loose soil complete all as specified.

M&L for hardcore of brocken stone or boulder gauge n exc 63mm, deposited, sprade and levelled in layers n exc 15cm thick watered and rammed to true surface.

M&L for 150 mm thick PCC 1:4:8, type D-2 (using 40mm graded crushed stone aggregate) in sub-base including necessary formwork complete all as specified and directed.

All as per item No 155.00 above, but 75 mm thick PCC complete.

M&L for laying 100mm PCC (1:2:4) B-2 using 40mm graded stone aggregate as in flooring / HS /paving inculding fixing of glass strips, complete as specified and directed. Note:- Glass strip will be measured and paid separatly.

All as per item No 157.00 above, but 75 mm thick PCC complete.

Supply only glass dividing strips 3 mm thick for 38 mm width fixed to floor over 2.5 mtrs panel etc complete all as specified and directed.

M &L for 25mm thick sand filling (sand cushioning) under path for laying interlocking paver block as specified and directed.

M&L Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade with grey cement and pigment etc complete all asspecified and directed.

M&L for PCC 1:4:8 Type D-2 (using 40mm graded stone aggregate) as in foundation filing,surface channel and drain etc complete.

M&L Reinforced cement concrete 1:2:4 type B-1 ( using 20 mm graded aggregate) as in beams, lintel band, roof band, gable band etc all as specified and directed by Enge-in-Charge.

M&L formwork to flat rough finished surfaces of concrete of foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams, and similar work vertical or to batter all as specified and directed by Engr-in-Charge

M&L 15mm thick cement plaster in cement mortar 1:4 on bricks or concrete surface and finished even and fair on external surface of wall

M&L preparation of new surface in wall and applying three coats of white wash complete all as specified and directed

M&L for cement concrete Type C-1,1:3:6 (20 mm graded aggregate) 75 mm thick as in plinth protection finishes even and fair without using extra cement finishing exposed edges fair for rounding and in phase every 2 mtr for length and joint shall be finsihed with bitumen and sand mixtures 1:3 complete all as spd and directed.

M&L for 25mm thick PCC 1:2:4 type B-1 (20 mm graded aggregate) as in levelling course.

M&L for 20 mm thick Screed bed or bedding layer of morter for laying floor finishes CM 1:4.

M & L for Plain 0.63mm thick, galvanised, mild steel sheeting, in ridges,hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275

S & F Mild steel, 1.25mm thick plain, black sheet in wall cladding,steel gates and similar work, cut to size, holes punched; includinground headed screws, clout nails or rivets E42and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required

M&L for Surface excavation n.exc 30 cm deep and averaging 15cm deep and getting out in any type of soil .

M&L for 75 mm thick PCC 1:4:8 Type D-2 (using 40mm graded stone aggregate) as in foundation filing, sub base complete.

Taking down carefully point wiring of any type, size and description (light, fan, socket outlet etc.) including removal of battens, pipes, sockets, switches, ceiling roses, light fittings etc, complete and making good the disturbed surfaces to match with existing, all as specified and as directed.

Taking down main switches, distribution boards etc of any type and capacity along with the existing boards, and removing the same from site and making good the disturbed surfaces/portion of walls etc. all as directed.

Taking down old and unserviceable sub main wiring of any size and description and removable the same from site and making good the disturbed surfaces/portion of walls etc. all as directed.

M & L for concealed point wiring complete with PVC insulated /unsheathed stranded copper conductor of wire 1.5 Sqmm , 1100 volt grade , alongwith one single core of same size stranded copper as continuous earth wire to common earth dolly in and including PVC conduit pipe fitting medium grade of 20 mm dia fixed in concealed surface of wall/ceilling/false ceilling including cutting /chasing in wall as required with powder coated sheet metal terminal boxes of required sizes and thickness (factory made) sunk in wall only with 3.0mm thick laminated sheet where as required and accessories complete suitable for the following :-

(a) One light/fan point controlled by one on way switch

(b) One socket outlet 05 Amps on the same board

(c) One socket outlet 05 Amps on independent board

(d) One bell/buzzer point controlled by on bell push

All as per item No. 177.00 above but point wiring with 2.5 Sqmm cable and 2.5 Sqmm earth continuity conductor for 3 pin 15 Amp socket and all as specified and directed.

S&F 3 pin 15 Amps switch socket combination, flush type multi purpose 2 in 1 type (3 pin 5 Amps and 15 Amps) all as specified.

S& F ceiling rose, 5 Amps surface type 240 volts bakelite three terminal as ordered and directed .

S&F 3 pin 5 Amps socket flush type multi purpose 2 in 1 type (2 pin and 3 pin) and all as specified and directed.

S&F Switch piano, single pole one way 5 Amps 240 volt capacity flush type all as specified.

S&F 3/5 pin 5 Amps Switch and socket combination flush type multi purpose 2 in 1 type (2 pin and 3 pin) and all as specified and directed.

S&F fan regulator electronic step type 230 volts suitable for any type of ceiling fan sweep all as specified and directed.

Supply & fix sheet metal enclosures for DBs when MCBs to be used SPN, flush/surface mounting double door distribution board 8 way, factory made and tested complete, suitable for mounting MCBs with 200 Amps tinned copper bus bar, cable lugs complete.

All as per Item no 185.00 above but 4 way complete.

All as per Item no 185.00 above but 12 way complete.

Supply & fix sheet metal enclosures for DBs when MCBs to be used TPN, flush/surface mounting single door distribution board 4 way, factory made and tested complete, suitable for mounting MCBs with 200 Amps tinned copper bus bar, cable lugs complete.

S & F MCB SPN of rating 06 to 32 Amp, 240 Volt, 10 KA, 'C' series.

S & F MCB SP of rating, 06 to 32 Amp,240 volt, 10 KA 'C' Series.

S & F MCB TPN of rating, 40 to 63 Amp,415 volt, 10 KA 'C' Series.

M&L for concealed sub main wiring of two run with 04 Sqmm single core PVC insulated, FR, flexible multi stranded copper conductor cable 1100 volts grade, drawn through and including PVC conduit pipe 25 mm dia medium grade and accessories of suitable size and fixed on concealed surface of wall/ceiling with cutting chases for conduit including one run of 4.0 Sqmm single core PVC insulated, FRLS , flexible copper cable as earth continuity conductor in green color all as specified and as directed. Note- (a) Two runs of single core cable with one run of earth continuity cable including PVC conduit and its accessories will be measured and paid as one unit). (b) Make disturbed surface good to wall/floors .

M & L for Earthing complete with galvanized steel earth plate electrode 600x600x6mm thick electrode, buried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 meters below normal ground level, connected to galvanized earth lead wire 4.0 mm dia by means of bolts, nuts, check-nuts and washers of galvanized iron or steel all as shown in electrical plate No 5 (duly protected with 15 mm dia light grade GI pipe upto 7.5 m from the earth plate) and connected to GI steel earth plate including charcoal, dust, common salt necessary excavation in soft/loose soil, returning filling in and removal of surplus soil to a distance not exceeding 50 m from the starting point, watering pipe 20 mm dia GI light grade treated with 1 No PGI funnel, pit of PCC 1:2:4 type B-1, RCC 1:2:4 type B-1 pit cover 75 mm thick reinforced with 6 mm dia bars @ 75 mm c/c both ways and with MS handle 12 mm dia complete connected to earth test point including testing complete all as specified and directed.

S&F 4 ft 18 watt Universal batten for T5 and T8 lamps . The tube should Ultra bright glass LED Tubelight with very high efficacy suited for installation in existing T8 fitting with G13 lamp holders. Make:- Havells/Orient/ Bajaj/Philips/CG

S&F 2 feet 09 W slim LED battern (cool day light) Basic all purpose surface and wall mounted with polycarbonate housing & integrated with electronic driver.. Make:- Havells/Orient/ Bajaj/Philips/CG

S&F copper bus bar chamber of rating 100 amp, TPN factory made , dust and vermin proof including busbar of rectangular cross section of copper strip supported on cast epoxy insulator at suitable interval heat shrinkable sleeves with powder colour code 01 set of 04 strip of complete with grounting in wall with suitable FI strip bend to shape with PCC work for holding enclosure and as directed by Engr-in-Charge .

S&F LED security light luminaire 1x25W Energy saving and enviornmental friendly long life LED Street light made up of pressure die cast aluminium housing with acrylic cover as diffuser with IP-66 protection and impact resistance of IK07 complete with all accessories and all as specified and directed by Engineer in Charge. Make:- Havells/Orient/ Bajaj/Philips/CG

S& F Fluorescent tube light fitting 1 x36W flameproof type FLP-WP made of aluminium alloy LM6, with electronic ballast, bipin holders, connector block, etc. complete with all accessories prewired and including connecting up with twin core twisted flexible copper conductor cable with suitable size.

Dismantling of water tanks upto 5000 Litres capacity complete.

S&F rotational moulded polythene water storage tank (cylinerical vertical /square type with closed top) hoisted and fixed in position all as specified in SSR part-1 of 5000 liters capacity all as specified and as directed.

Supply and Fix 25 mm Galvanised Steel water tubing (ISI Marked ) medium grade with and including all tube fittings and fixtures such as GI bends tee union etc in trenches/fixed to wall/ fixed on piller complete and connecting to water supply pipe line and testing complete all as and as directed.

S & F 25 mm dia Gun metal , globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed.

DMA PROJECTS