Construction of Waste processing Site at PO. Chikhla (S.No. 16 & 17) for the Ambaji Area Development & Pilgrimage Tourism Governance Authority

Excavation for foundation upto 1.5 m depth including

sorting out and stacking of useful materials and disposing

off the excavated stuff upto 50 Meter lead.(D) Soft rock not

requiring Blasting

Conveyance charges of earth lime, murrum, building

3 rubbish, manure, garbage, sludge, excavated rock, fly ash, Cmt 389.00 237.87

aggregate of any kind etc. comp. upto 5 km lead.

Extra For Lead Above 5 km & upto 6 km Cmt 78.00 9.35

Extra For Lead Above 6 km & upto 7 km Cmt 78.00 9.35

Extra For Lead Above 7 km & upto 8 km Cmt 78.00 9.35

Extra For Lead Above 8 km & upto 9 km Cmt 78.00 9.35

Lead Above 9 km Cmt 78.00 9.35

Filling available excavated earth (excluding rock) in

trenches. plinth, sides of foundations etc. in layers not

exceeding 20 cm. in depth consolidating each disposited

layer by ramming and watering.

Filling in plinth with sand under floors including watering

5 ramming, consolidating and dressing complete cmt 18.00 444.75

Filling in foundation and plinth with murrum or selected

6 soil in layers of 20cm. thickness including watering, cmt 18.00 282.07

ramming and consolidating etc. complete.

Carring out plinth treatment to post construction /existing

structure by spraying chemical solution for termite control

treatment including labour and material consistment with

I.S.I specification. Using Chlordene and Chiorpurfiles 20 EC.

As Per 6131_paret-II Consentration Weight one percent is

7 recommended i.e one litre 20 EC chemical emulsion with Smt 179.00 86.86

19 liter give 1% concrentration inclusive of one litre

chemical emulsion appication at the rate of 5 Litre

chemical /Sqm of sur face is recommended as per I.S

M/S JAG DESIGNERS PVT.LTD.

ARCHITECTS -URBAN PLANNER-INTERIOR DESIGNER-PMC-REG.VALUER-ENGINEER

SR. NO. ITEM DESCRIPTION UNIT Qtty SOR RATE 2024-25 AMOUNT

Providing and laying cement concrete 1:3:6 (1-Cement:3-

coarsesand:6-hand broken stone aggregates 40mm

8 nominal size)and curing complete excluding cost of Cum 821.00 2978.97

formwork in (A) Foundation and Plinth.

Providing and laying controlled cement concrete M.250

and curing complete excluding the cost of formwork and

9 reinforcement for reinforced concrete work in (A) Cum 37.00 4232.84

Foundations, footings, Base of columns and Mass concrete.

Providing and laying controlled cement concrete M.250

and curing complete excluding the cost of formwork and

reinforcement for reinforced concrete work in (A)

Foundations, footings, Base of columns and Mass concrete.

BELOW PLINTH COLUMN

Providing and laying controlled cement concrete M.250

and curing complete excluding the cost of formwork and

11 reinforcement for reinforced concrete work in (D) Cum 19.00 4621.82

Columns, Pillars posts and struts, upto floor two

level.ABOVE PLINTH COLUMN

M/S JAG DESIGNERS PVT.LTD.

ARCHITECTS -URBAN PLANNER-INTERIOR DESIGNER-PMC-REG.VALUER-ENGINEER

SR. NO. ITEM DESCRIPTION UNIT Qtty SOR RATE 2024-25 AMOUNT

Providing and laying controlled cement concrete M.250

and curing complete excluding the cost of formwork and

reinforcement for reinforced concrete work in ©

Slabs,landing,shelves,Balconies, Lintels, Beams, Girders and

Cantilever upto floor two level.PLINTH BEAM , Road

Providing and laying controlled cement concrete M.200

and curing complete excluding the cost of formwork and

reinforcement for reinforced concrete work in ©

Slabs,landing,shelves,Balconies Lintels, Beams, Girders and

Cantilever upto floor two level.

Providing and laying controlled cement concrete M.250

and curing complete excluding the cost of formwork and

14 reinforcement for reinforced concrete work in (B) Walls, Cum 47.00 4543.04

from top of foundation level upto floor two level

Providing TMT Bar FE 500D reinforcement for R.C.C. work

15 including bending, binding and placing in position complete Kg 38730.00 77.29

upto floor two level

Providing formwork of ordinary timber planking so as to

give a rough finish including centering shuttering strutting

and propping etc. Height of propping and centering below

supporting floor to ceiling not exceeding 4 M. and removal

of the same for in situ reinforced concrete and plain

concrete work in. (A) Foundations Footings Bases of

Columns etc. and Mass concrete.

Providing formwork of ordinary timber planking so as to

give a rough finish including centering shuttering strutting

and propping etc. Height of propping and centering below

supporting floor to ceiling not exceeding 4 M. and removal

17 of the same for in situ reinforced concrete and plain Smt 219.00 267.25

concrete work in. (B) Flat surfaces such as soffits of

supspened floors slabs Landings and the like. (1) Floors etc.

upto 200 mm in thickness.

Providing formwork of ordinary timber planking so as to

give a rough finish including centering shuttering strutting

and propping etc. height of propping and centering below

supporting floor to ceiling not exceeding 4 M. and removal

of the same for in situ reinforced concrete and plain

concrete work in. (G) Columns PillarsPosts and struts. (1)

Square Rectangular Polygonal in plan.

M/S JAG DESIGNERS PVT.LTD.

ARCHITECTS -URBAN PLANNER-INTERIOR DESIGNER-PMC-REG.VALUER-ENGINEER

SR. NO. ITEM DESCRIPTION UNIT Qtty SOR RATE 2024-25 AMOUNT

Providing formwork of ordinary timber planking so as to

give a rough finish including centering shuttering strutting

and propping etc. height of propping and centering below

supporting floor to ceiling not exceeding 4 M. and removal

19 of the same for in situ reinforced concrete and plain Smt 479.00 273.93

concrete work in. (H) (2) Sides and soffits of Beams Beam

Haunchings canti-levers Girders Bressumers and Lintels

exceeding 1M.in Depth.

Providing formwork of ordinary timber planking so as to

give a rough finish including centering shuttering strutting

and propping etc. height of propping and centering below

supporting floor to ceiling not exceeding 4 M. and removal

20 of the same for in situ reinforced concrete and plain Smt 423.00 243.86

concrete work in. (C) Vertical surface such as walls (any

thickness) partitions and the like including attached

buttresses & string course & the like.

Brick work using common burnt clay building bricks having

crushing strength not less than 35 kg./Sq.Cm. in foundation

and plinth in Cement Mortar 1:5. (1- Cement : 5 -fine

sand)(B) Conventional

Brick work using common burnt clay building bricks having

crushing strength not less than 35 kg./Sq.Cm. in foundation

and plinth in Cement Mortar 1:5. (1- Cement : 5 -fine

22 sand)(B) Conventional Extra for brick work in Cum 186.00 4526.81

superstructure above plinth level

upto floor two level (B) Conventional GROUND FLOOR

Brick work using common burnt clay building bricks having

crushing strength not less than 35 kg./Sq.Cm. in foundation

and plinth in Cement Mortar 1:5. (1- Cement : 5 -fine

sand)(B) Conventional Extra for brick work in

23 superstructure above plinth level Cum 11.00 4569.24

upto floor two level (B) Conventional Extra for brick work in

superstructure above floor two level FIRST FLOOR

(i) Half brick masonry in common brunt clay building bricks

having crushing strength not less than 35 Kg/Sq.Cm. in

Cement mortar 1:4 (1- Cement : 4 -coarse sand ) in

24 foundation and plinth (B) Conventional Extra for half brick Smt 44.00 684.26

masonry in superstructure above plinth level upto floor

two level. (B) Conventional

M/S JAG DESIGNERS PVT.LTD.

ARCHITECTS -URBAN PLANNER-INTERIOR DESIGNER-PMC-REG.VALUER-ENGINEER

SR. NO. ITEM DESCRIPTION UNIT Qtty SOR RATE 2024-25 AMOUNT

Providing 15mm thick cement plaster in single coat on

Rough (Similar)side of single or half brick walls for interior

plastering upto floor two level and finished even and

smooth in (ii) Cement mortar 1:4 (1-cement :4-sand)

Providing 10mm thick cement plaster in single coat on

brick/concrete walls for interior plastering upto floor two

26 level and finished even and smoothin (ii) Cement mortar Smt 130.00 125.12

1:4 (1-cement :4-sand) with Water proofing materials

silicon base Water repellent compund

20 mm thick sand faced cement plaster on walls upto

height 10 metres above ground level consisting of 12 mm

27 thick backing coat of C.M.1:3 (1-cement:3-sand) and 8mm Smt 831.00 320.70

thick finishing coat of C.M.1:1(1-cement:1-sand) etc.

Providing cement vata (10cm. x 10 cm. size) quarter round

28 in cement mortar 1:1 including neat cement finishing, Rmt 99.00 24.28

watering etc. complete.

Applying two coats of putty & two coats of primer of

approved brand and manufacture on new wall surface to

29 give an even shade including thoroughly brushing the Smt 648.00 40.59

surface free from mortar dropping and other foreign

matter and sand papered smooth.

Wall painting (two coats) with plastic emulsion paint of

approved brand and manufacture on undecorated wall

surface to give an even shade including throughly brushing

the surface free from mortar droppings and other foreign

matter and sand papered smooth.

Finishing wall with weather proof exterior emulsion paint

on wall surface (two coats) to give an required shape even

31 shade after thoroughly brushing the surface to remove all Smt 831.00 73.83

dirt, and remains of loose powdered materials.etc

Providing and laying Ceramic tiles 6mm thick in flooring

treads of steps and landing laid on a bed of 12mm thick

32 cement mortar 1:3 (1-cement : 3- coarse sand ) finishing Smt 59.00 987.14

with flush pointing in white cement.

P & L 24" x 24" vitrified 8 mm thick tile flooring over 20 mm

(average) base of cement mortar 1:6 ( 1 cement: 6 coarse

sand) on new surface or fixing on existing flooring by

adhesive material including dismentaling of existing

flooring and jointed with color cement slurry including

finised with flush pointing & cleaning the surface etc.

M/S JAG DESIGNERS PVT.LTD.

ARCHITECTS -URBAN PLANNER-INTERIOR DESIGNER-PMC-REG.VALUER-ENGINEER

SR. NO. ITEM DESCRIPTION UNIT Qtty SOR RATE 2024-25 AMOUNT

P&L 24"x24" vitrified 8mm thick tile flooring over 20mm

(average) base of cement mortar 1:6 (1cement :6 coarse

sand) on new surface or fixing one xisting flooring by

adhesive material including dismentaling of existing

flooring and jointed with color cement slurry including

finised with flush pointing & cleaning the surface

etc.complete for antiskid

Providing and laying white glazed tiles 6mm thick in skrting

risers of steps and dedo on 10 mm thick cement plaster

1:3(1-cement :3-coarse sand)and jointed with white

Providing and laying polished Kota stone slab flooring over

20mm (Average) thick base of cement mortar 1:6 (1-

cement : 6-coarse sand) or L.M. 1.1.5 laid over and jointed

with grey cement slurry including rubbing and polishing

etc. complete. (B) 30 mm thick

Providing and laying 40mm thick marble chips flooring

rubbed and polished (I.E. terrazo) to granolithic finish with

under layer 30mm thick cement concrete 1:2:4 (1-

Cement:2-coarse sand :4-graded stone aggregate 10 mm

and down gauge) and top layer 10mm thick with white,

37 black or white and blak marble cihps of required sizes from Smt 10.00 908.64

1mm to 4mm nominal size laid in cement marble powder

mix 3:1 (3-Cement : 1-Marble powder by weight) in

proportion of 4:7 (4-Cement :7-marble chips by volume) (B)

Light shade pigment with white cement (In top layer only)

Providing and laying marble stone slab flooring over 20mm

(average)base of cement mortar 1:6 (1-cement : 6 coarse

sand) or L.M. 1:1.5(1- lime putty : 1.5 - coarse sand) laid

and jointed with gray cement slurry including rubbing and

polishing complete. (A) Marble slab 25mm thick

Providing and fixing M.S. grills of required pattern to

wooden frames of windows etc. with M.S. flats at required

spacings and frame alround, square or round bars with

round headed bolts and nuts or by screws (A) Plain Grill.

Providing and fixing standared extruded of alluminium

section of size 63mmx 38.10 mm x 1.2mm @Wt.0.643Kg

40 /mt with colour anodized alluminium frame for ventilation Smt 3.00 1175.56

with 5mm thick frosted glassas details etc complete for

M/S JAG DESIGNERS PVT.LTD.

ARCHITECTS -URBAN PLANNER-INTERIOR DESIGNER-PMC-REG.VALUER-ENGINEER

SR. NO. ITEM DESCRIPTION UNIT Qtty SOR RATE 2024-25 AMOUNT

Providing and fixing window having extruded aluminum

Colour Powder Coated section frame main outer size

x 38.10 x 1.95 mm,@ Wt 1.094 Kg / Rmt, horizontal two

track member size 61.85 mm x 31.75 mm x 1.20mm @

wt.of 0.695 Kg/mt, vertical member of size 61.85 mm x

31.75mm x 1.30 mm @ wt.of 0.0.659 Kg/mt with sliding

shutters of horizontal member size 40mm x 18mm x

41 1.29mm @ wt.of 0.456Kg/mt, vertical member of size Smt 17.00 1705.67

40mm x 18mm x 1.29mm @ wt.of 0.456Kg/mt with 5 mm

thick transparent bronze colour tinted float glass with

powder coated aluminum fittings and fixtures and

transparent silicon sealant glass fixing to frame as per

complete for window

Providing and fixing 35 mm thick shutters for Doors,

windows and clerestory windows including Indian teak

wood frames 10 cm x 7 cm. size including anodized

alluminium fixtures and fastenings including primer coat of

approved quality and two coats of oil painting etc,

complete. (i) Fully Glazed.

Providing and fixing FRP frame size 125x65mm and 35 mm

thick FRP shutter with wood grain raised pannel edde sign

finish shutter having extra reinforcement on sides & edges

in Gel coat finish. The core of the shutter & frame is to be

filed up with injected polyurethene foam done in situa long

with embedded wooden pieces for stiffening & also taking

hinges & fintures. The whole FRP frame &shutter is to be

water proof weathe rproof ,termite proof & resistance to

mild acid/alkali. Rate sare to be inclusive of S.Shinges with

fastener sleeve & alluminium fixtures & fastenings.

Providing & Laying P21(water reducing concrete admixture

at 100 ml per bag of cement & recon 3 s fiber at 125 gm

per bag of cement including making C channel 75 x 75 mm

required to maintain level,slope and thickness of the

44 concrete road leveling of placed concrete with surface Smt 5000.00 90.90

vibrator and finishing with power floater & trowel light

brooming the surface & including cutting & filling of

expansion joint as directed by Engineer in charge.

Providing and filling rubbles including hand packing and

45 filling interstices with quarry spalls behind abutments and Cum 1150.00 1046.27

between returns as directed.

M/S JAG DESIGNERS PVT.LTD.

ARCHITECTS -URBAN PLANNER-INTERIOR DESIGNER-PMC-REG.VALUER-ENGINEER

SR. NO. ITEM DESCRIPTION UNIT Qtty SOR RATE 2024-25 AMOUNT

Providing, laying, spreading and compacting Wet Mix

Macadam (as per table 400 - 10 and 400 - 11) of well

graded stone aggregate to specification including premixing

the Material with water at OMC in mechanical mix plant as

per approved design mix, carriage of mixed material by

Tipper to site, laying in uniform layers with motor

46 grade/Front end Loader/paver finisher, in sub base/base Cum 500.00 1727.10

course on a well prepared under base and compacting with

vibratory roller to achieve the desired density including

lighting, guarding, barricating and maintenance of diversion

etc. (MoRTH specification : Clause 406) by mechanical

Providing and fixing pre-cast concrete kerb stone of gray

cement based concrete block 30cm length,30cm height

and 15cm thick of M250 grade concret as per approved

47 design and including excavation for fixing in proper line and Rmt 300.00 374.92

level,filling the joint with C:M 1:3 (1cement:3fine sand) etc

Providing and fixing pre-cast Rubber Dye / steel Dye inter

locking concrete block 60mm thick with grade of concrete

M300 pnumatic compressed / vibrated mechanically and as

per approved design Confirming to IS 15658 :

including 35 mm Sand layer for levelling and filling the joint

with sand in proper line and level as per guidlines of IRC :

SP 63-2018 etc. Complete.

Road marking with hot applied thermoplastic paints with

reflectorising glass beads on bitumin surface providing and

laying a hot applied thermoplastic compound 2.5 mm thick

including reflectorising glass beads @ 250gms per sqm

area, thickness of 2.5mm is excluding of surface applied

glass beds as per IRC:35-2015. The finished surface to be

level, uniform and free from streaks and holes. zebra patta

/bump patta lane/center line/ edge line/cut patta. The

white color marking should provide liminance coefficinet

on cemend road shalll be min 130 mcd/m2/lux and Asphalt

road shall be min 100 mcd/m2/lux during the service life

during the day time. The marking should meet the

performance criteria for night time reflectivity, wet

reflectivity and skid resistance as mentioned in the section-

15 of IRC 35-2015. Warranty for the Retro reflectivity

should be two years.

M/S JAG DESIGNERS PVT.LTD.

ARCHITECTS -URBAN PLANNER-INTERIOR DESIGNER-PMC-REG.VALUER-ENGINEER

SR. NO. ITEM DESCRIPTION UNIT Qtty SOR RATE 2024-25 AMOUNT

Providing and laying broken chine mosaic flooring for

terrace using 12 mm to 20 mm broken pieces of glazed tiles

to be laid over cement mortar 1:3 to plain or slope and to

be tempered to bring mortar creme out upto surface using

white cement including rounding off junctions and

extending them upto 15 cm along the wall,clearing with

water and oxalic acid etc. as directed.

Structural steel work ( Confirming to IS 4923-1997) riveted,

bolted or welded in builtup for all type sections, in framed

work, including cutting, hoisting, fixing in position and

51 applying a priming coat of approved steel primer all Kg 7300.00 131.83

complete as per the

structural designs and directions of Engineer in charge.

Painting one coats (excluding priming coat) on previously

printed steel and other metal surface with synthetic

52 enamel paint, brushing to give an even shade including Smt 1540.00 53.48

cleaning the surface of all dirt, dust and other foreign

53 Chicken wire mesh 16 x24 Smt 64.80 184.02

Providing corrugated G.I. sheet of class-3 roofing fixed with

glavanished iron J or L Hooks, Bolts and nuts 8mm diameter

with bitumen and G.I. limpet washer or G.I. limpet washer.

filled with white lead complete excluding the cost of

purlins, Rafters and Trusses.(1) 0.80 mm thick sheet.

Bamboo is a fast-growing woody grass known for its high

strength-to-weight ratio. Commercially, it is categorized by

its growth habit (clumping vs. running) and its structural

Precast concrete block masonry in partition walls 10 cm.

thick with solid block of approved size (including quion

blocks Jamb blocks closer etc.) made of C.C.1:3:6 (1-

Cement : 3- coarse sand : 6 graded stone aggregates

and down grade) (A) in C.M. 1:4.

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2

working pressure poluthene pipes of the following outside

Dia. Low densidy, complete with special falnge

compression type fittings, wall clipsetc. including making

good the wall ceiling and floor.(C) 32mm

M/S JAG DESIGNERS PVT.LTD.

ARCHITECTS -URBAN PLANNER-INTERIOR DESIGNER-PMC-REG.VALUER-ENGINEER

SR. NO. ITEM DESCRIPTION UNIT Qtty SOR RATE 2024-25 AMOUNT

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2

working pressure poluthene pipes of the following outside

Dia. Low densidy, complete with special falnge

compression type fittings, wall clipsetc. including making

good the wall ceiling and floor.(D) 40mm Wash Out Pipe

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2

working pressure poluthene pipes of the following outside

Dia. Low densidy, complete with special falnge

compression type fittings, wall clipsetc. including making

good the wall ceiling and floor.(E) 50mm Wash Out Pipe

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2

working pressure polythene pipes of the following outside

Dia. Low densidy, complete with special falnge

60 compression type fittings, wall clipsetc. including making Rmt 50.00 280.23

good the wall ceiling and floor.(F) 75mm ( Waste Pipe &

Rain & Balcony Drain)

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2

working pressure poluthene pipes of the following outside

Dia. Low densidy, complete with special falnge

compression type fittings, wall clipsetc. including making

good the wall ceiling and floor.(G)110 mm ( Rain & Balcony

Providing and fixing 600mm x 450mm bevelled edge

mirrror of superior glass mounted on 6mm thick A.C. sheet

or plywood sheet and fixing to wooden pluge with C.P.

brass screws and washers.

Providing and fixing C.P. brass towel rail comlete with C.P.

63 brass brackets fixed to wooden plugs with C.P. brass Each 5.00 616.42

scews.(B) 600mm x 20mm size.

Providing and fixing 600mm x 120mm glass shelf with C.P.

64 brass bracket and guard rail complete mixed to wooden Each 5.00 586.09

plug with C.P. brass screws.

65 Providing and fixing toilet paper holder.(A) C.P. Brass Each 5.00 375.82

Providing and fixing screw down bib taps of following

66 size.(A) Brass screw down bib tap polished bright. (i) Each 5.00 186.83

Providing and fixing screw down bib taps of following

67 size.(B) Brass chromium plated screws down Bib Tap. (i) Each 5.00 186.83

Providing and fixing screw down bib taps of following

68 size.(C) Gun metal screw down bib tap. (i) 15mm dia. Each 4.00 158.86

Providing and fixing pillar tap, capstan head, screw down

69 high pressure with screws, shanks and back nuts. (i) Each 5.00 308.73

M/S JAG DESIGNERS PVT.LTD.

ARCHITECTS -URBAN PLANNER-INTERIOR DESIGNER-PMC-REG.VALUER-ENGINEER

SR. NO. ITEM DESCRIPTION UNIT Qtty SOR RATE 2024-25 AMOUNT

Providing and fixing brass screw down stop tap.(A) 15mm

Providing and fixing brass screw down stop tap.(C) 25mm

Providing and fixing Gun metal check or non-return fullway

wheel valve.(A) 15mm dia.

Providing and fixing Gun metal check or non-return fullway

wheel valve.(B) 20mm dia.

Providing and fixing Gun metal check or non-return fullway

wheel valve.(C) 25mm dia.

Providing and fixing Gun metal check or non-return fullway

wheel valve.(D) 32mm dia.

Providing and fixing Gun metal check or non-return fullway

wheel valve.(E) 40mm dia.

Providing and fixing chromium plated brass half trun flush

77 cock of approved quality including fixing in pipe line etc. Each 5.00 263.77

complete.(ii) 25mm dia.

Providing and fixing chromium plated brass half trun flush

78 cock of approved quality including fixing in pipe line etc. Each 5.00 275.76

complete.(iii) 32mm dia.

Providing and fixing ball cock of approved. quality as

directed.(A) Copper Metal (i) 25mm dia.

Providing and fixing ball cock of approved. quality as

directed.(A) Copper Metal (ii) 50mm dia.

Providing and fixing ball cock of approved. quality as

directed.(B) Abonite (i) 25mm dia.

Providing and fixing ball cock of approved. quality as

directed.(B) Abonite (ii) 50mm dia.

Providing and fixing C.I. Manhole cover 0.60 M. x 0.45M.

size having weight not less than 35Kg.

Providing and fixing G.I. Rain water spout of 50mm dia. and

Providing and fixing concealed center point to wall ceiling

& floor CPVC (SDR 13.5) PIPE having National Sanitation

Foundation (NSF) seal for potable water of following dia.

nominal bore tube fittings and clamps including making

good the wall, ceiling and floor etc. complete.[A] 15 mm.

Providing and fixing concealed center point to wall ceiling

& floor CPVC (SDR 13.5) PIPE having National Sanitation

Foundation (NSF) seal for potable water of following dia.

nominal bore tube fittings and clamps including making

good the wall, ceiling and floor etc. complete. [B] 20 mm.

M/S JAG DESIGNERS PVT.LTD.

ARCHITECTS -URBAN PLANNER-INTERIOR DESIGNER-PMC-REG.VALUER-ENGINEER

SR. NO. ITEM DESCRIPTION UNIT Qtty SOR RATE 2024-25 AMOUNT

Providing and fixing concealed center point to wall ceiling

& floor CPVC (SDR 13.5) PIPE having National Sanitation

Foundation (NSF) seal for potable water of following dia.

nominal bore tube fittings and clamps including making

good the wall, ceiling and floor etc. complete. [C] 25 mm.

Providing and fixing concealed center point to wall ceiling

& floor CPVC (SDR 13.5) PIPE having National Sanitation

Foundation (NSF) seal for potable water of following dia.

nominal bore tube fittings and clamps including making

good the wall, ceiling and floor etc. complete. [D] 32mm.

Providing and fixing concealed center point to wall ceiling

& floor CPVC (SDR 13.5) PIPE having National Sanitation

Foundation (NSF) seal for potable water of following dia.

nominal bore tube fittings and clamps including making

good the wall, ceiling and floor etc. complete. [E] 40mm.

Providing and fixing concealed center point to wall ceiling

& floor CPVC (SDR 13.5) PIPE having National Sanitation

Foundation (NSF) seal for potable water of following dia.

nominal bore tube fittings and clamps including making

good the wall, ceiling and floor etc. complete. [F] 50mm.

Providing and fixing gun metal gate valve with C.I. wheel of

91 approved quality (screwed end) :65 mm nominal bore No. 2.00 1759.57

Providing &Laying & fixing PVC Floor Trap OR multi floor

trap of 110 x 110mm dia diameter, with necessary distance

piece of 110mm dia pipe and 150x150mm Chillay /Camry/

92 S.S. Three Pease grating, making necessary SLAB each 13.00 733.26

/WALLholes and cutting walls, etc complete. (Supreme/

DRAINAGE & SEWERAGE ITEM:- Excavation for

pipes upto1.50 MT depth including sorting out and stacking

93 of useful materials and disposing the excavated stuff up to Cmt. 200.00 122.94

50 mt lead ( A ) loose or Soft Soil

Providing and fixing S.W. gully trap with C.I. grating brick

masonry chamber and water tight C.I. cover with frame of

94 300mm x 300mm size (inside) with standard weight.(i) Each 3.00 1246.92

Square mouth traps.(B) 150mm x 100mm size P or R type

M/S JAG DESIGNERS PVT.LTD.

ARCHITECTS -URBAN PLANNER-INTERIOR DESIGNER-PMC-REG.VALUER-ENGINEER

SR. NO. ITEM DESCRIPTION UNIT Qtty SOR RATE 2024-25 AMOUNT

Providing laying (to level or slopes) and jointing reinforced

concrete Light duty non-pressure pipes I.S. class NP2 of the

95 following internal diameter with collars and butt ends Rmt 50.00 257.16

prepared for collar joints

including testing of joints complete.(B) 150mm

Providing laying (to level or slopes) and jointing reinforced

concrete Light duty non-pressure pipes I.S. class NP2 of the

96 following internal diameter with collars and butt ends Rmt 100.00 359.80

prepared for collar joints

including testing of joints complete.(C) 250mm

Providing laying (to level or slopes) and jointing reinforced

concrete Light duty non-pressure pipes I.S. class NP2 of the

97 following internal diameter with collars and butt ends Rmt 25.00 677.97

prepared for collar joints

including testing of joints complete.(D) 300mm

Constructing brick masonry chamber for underground C.I.

Inspection chamber and bends with briocks having croshing

strength not less than 35Kg. Cm2 in C.M. 1:5 C.I. cover with

frame (Light duty) 455mm x 610mm intenal dimensions

total weight of cover with frame to be not less than 38Kg.

(Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top

slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded

98 stone aggregate 20mm size) foundation concrete 1:5:10 Each 10.00 7180.44

inside plaster 15mm thick with cement mortar 1:3 finished

smooth with a floating coat of neat cement on walls and

bed concrete etc. complete.(iii) Inside dimensions 600mm

x mm and 450mm deep for pipe lines with three or more

Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1-

cement :2-coarse sand : 4-graded stone aggregate 20mm

nominal size) foundation concrete 1:3:6 mix (1-cement : 3-

coarse sand :6-Brick bats 40 + 50mm size) inside plastering

15mm thick with Cement Mortar 1:5 (1-Cement : 5-coarse

sand) finished with a floating coat of neat cement and

making channels in cement concrete 1:2:4 mix (1-Cement

:2-Coarse sand :4-stone aggregate 20mm nominal size)

finished smooth complete including curing and festing (i)

99 Inside size 900mm x 1200mm and 1.5M. deep including C.I. Each 10.00 11042.73

cover with frame size 560mm diameter total weight of

cover and frame to be not less than 128 kgs. (Wt. of cover

64 Kg. and Wt. of frame 64 Kg.)(A) With 230mm thick walls

of brick msonry using brick having crushing strength not

less than 35Kg. / Sq.cm. in Cement Mortar 1:5 (1-

Cement: 5-Coarse sand) (1) A type depth 0.90 Metre for

150mm diameter sewer.

M/S JAG DESIGNERS PVT.LTD.

ARCHITECTS -URBAN PLANNER-INTERIOR DESIGNER-PMC-REG.VALUER-ENGINEER

SR. NO. ITEM DESCRIPTION UNIT Qtty SOR RATE 2024-25 AMOUNT

Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1-

cement :2-coarse sand : 4-graded stone aggregate 20mm

nominal size) foundation concrete 1:3:6 mix (1-cement : 3-

coarse sand :6-Brick bats 40 + 50mm size) inside plastering

15mm thick with Cement Mortar 1:5 (1-Cement : 5-coarse

sand) finished with a floating coat of neat cement and

making channels in cement concrete 1:2:4 mix (1-Cement

:2-Coarse sand :4-stone aggregate 20mm nominal size)

finished smooth complete including curing and festing (i)

100 Inside size 900mm x 1200mm and 1.5M. deep including C.I. Each 5.00 19349.58

cover with frame size 560mm diameter total weight of

cover and frame to be not less than 128 kgs. (Wt. of cover

64 Kg. and Wt. of frame 64 Kg.)(A) With 230mm thick walls

of brick msonry using brick having crushing strength not

less than 35Kg. / Sq.cm. in Cement Mortar 1:5 (1-

Cement: 5-Coarse sand) (2) B type depth 1.50 Metre for

150mm diameter sewer.

Providing and fixing cast iron steps of size 500mm x

101 150mm x 22.5mm and painting with two coats of Anti- Each 71.00 207.66

corrosive paint etc. complete.

Supplying and fixing C.I. cover 300mm x 300mm without

102 frame for Gulley trap (Standard pattern) te weight of cover Each 5.00 497.14

to be not less 4.53 Kg.) .

Providing and fixing FRP frame size 100x50 mm and 28mm

thick FRP depress panel shutter having extra reinforcement

on sides & edges in Gel coat finish. The core of the shutter

& frame is to be filed up with injected fire retardant grade

polyurethene foam done in situ alongwith embedded

wooden pieces for stiffening & also taking hinges &

fintures. The whole FRP frame & shutter is to be water

proof weather proof, termite proof & resistance to mild

acid/alkali. Rates are to be inclusive of S.S hinges with

necessary screws & alluminium fixtures & fastenings &

fastener sleeve.

Providing and fixing water closet squatting Pan (Indian type

W.C. Pan) size 580mm (Earthwork, bed concrete, foot reste

and trap to be measured and paid for separately) (A)

Vitreous China.(I) Long pattern = White colour

Providing and fixing Urinal of approved quality including

connection with trap and with integral longitudinal flush

pipe.(A) Squating plate pattern white earthenware 550mm

M/S JAG DESIGNERS PVT.LTD.

ARCHITECTS -URBAN PLANNER-INTERIOR DESIGNER-PMC-REG.VALUER-ENGINEER

SR. NO. ITEM DESCRIPTION UNIT Qtty SOR RATE 2024-25 AMOUNT

Providing and fixing washbasin with single hole for pillar

tap with C.I. or M.S. brackets painted white including

sutting holes and making good the same but excluding

fittings.(A) Vitreous China:(ii) Flat Back washbasin 550 mm

x v 400mm size. (i) In white colour.

Providing and fixing screw down bib taps of following

107 size.(B) Brass chromium plated screws down Bib Tap. (ii) Each 21.00 214.81

Providing and fixing C.P. brass shower rose with 15mm or

108 20mm inlet.(A) 100mm dia. Each Each 7.00 282.16

Providing and fixing Gun metal check or non-return fullway

109 wheel valve.(A) 15mm dia. Each 15.00 186.83

Providing and fixing brass screw down stop tap.(A) 15mm

Providing and fixing Urinal or approved quality including

conecting the Urinal with waste pipe , tap etc. complete.(A)

White earthenware flat back or corner type size 430mm x

WATER COOLER ; Supply, installation, testing &

commissioning of S.S. storage type water cooler with

inbuilt with on line U.V. fultration along with built all

intercnnectio piping, supports and valve and other

electrical requirment ,along with inbuilt storage tank with

nessesarry accessories, safety valve, air valve, drain

arrangement, all insturumentation, base frame, necessary

electrification, etc. complete for Drinking Water supply. (

Voltas, Blu star, Power H2o Make) Capacity : 80 storage

capacity. Complete as directed by site eng. incharg.

PUDDLE SLEEVES:-Providing & Installing of the G.I. heavy

duty Puddle Sleeve in the UGT & OHT water tanks , durring

the construction of the RCC tanks. The pipe and flazes nut

bolt material are as per the IS recommondation must be

follow. all works must properly finishing as per site eng.

Incharge slab & Beams where ever req. 200 mm pipe dia x

M/S JAG DESIGNERS PVT.LTD.

ARCHITECTS -URBAN PLANNER-INTERIOR DESIGNER-PMC-REG.VALUER-ENGINEER

SR. NO. ITEM DESCRIPTION UNIT Qtty SOR RATE 2024-25 AMOUNT

PUDDLE SLEEVES:- Providing & Installing of the G.I. heavy

duty Puddle Sleeve in the UGT & OHT water tanks , durring

the construction of the RCC tanks. The pipe and flazes nut

bolt material are as per the IS recommondation must be

follow. all works must properly finishing as per site eng.

Incharge slab & Beams where ever req. ,80 mm pipe dia x

Providing & Installing of the G.I. heavy duty Puddle Sleeve

in the UGT & OHT water tanks , durring the construction of

the RCC tanks. The pipe and flazes nut bolt material are as

115 per the IS recommondation must be follow. all works must Nos. 10.00 2110.90

properly finishing as per site eng. Incharge slab & Beams

where ever req. ,50 mm pipe dia x 450mm length

Providing erecting and fixing double coated ISI water tank

116 of required capacity each with all necessary fittings and Ltr. 25000.00 3.95

connection etc. complete on terrace

Constructing brick masonry chamber for underground

C.I. inspection chamber and bends with bricks having

crushing strength not less than 35 kg./Sqcm. In C.M. 1:5

Perforated C.I. cover with frame (Light duty) 455 mm. x

mm. internal dimension, total weight of cover with frame

to be not less than 38 kg. (Weight of cover 23 kg. and

weight of frame 15 kg.) R.C.C. top slab of cover 23 kg. and

weight of frame 15 kg.) R.C.C. top slab with 1:2:4 mix (1

cement: 2 coarse sand : graded stone aggregate

mm. nominal size) foundation concrete 1:5:10 inside

plaster 15 mm. thick with cement mortar 1:3 finished

smooth with a floating coat of neat cement on walls and

bed concrete etc. complete. [I] Inside Dimensions 455mm x

610 mm & 900 mm deep ( Valve Chamber)

M/S JAG DESIGNERS PVT.LTD.

ARCHITECTS -URBAN PLANNER-INTERIOR DESIGNER-PMC-REG.VALUER-ENGINEER

SR. NO. ITEM DESCRIPTION UNIT Qtty SOR RATE 2024-25 AMOUNT

PERCOLATION WELL:- Drilling of Pilot bore hole in Alluvial

Strata by Direct Rotary Rig of 250 mm. 60 rmtr., Reaming

400 mm.:- 60 R.mtr,Electrologging charges with carting.:-

1 job.,Providing and installing 200 mm dia IS:12818 uPVC

Casing Pipe "CM" Class Plain Pipe. :- 30 R.mtr, Providing

and installing 200 m1 Job.m dia IS:12818 uPVC End Cap,

with Air Vent Cowl.:- 1 Job.,Supply of Pea sized Gravel.:-

Cu.mtr, Air Vent of 50 mm bend:- 1 Unt, Lowering and

removing of dropline up to depth 186 Mtr. :- 60 R.mtr., Air

compressor 600 CFM/150 PSI.:- 1 Lot., Excavating pit for

installing precast filter system 2.90 x 2.90 x 1.125 Mt. deep.

:- 10 Cu.mtr., Providing PCC of 75 mm thickness of 1:4:8

grade. :1 CMT., Providing & laying Precast RCC M

rainwater filtration system of Inner dimention 1.00 x

x 1.00 Mt. & Minimum 50 mm wall thickness. 2 numbers of

50 mm thick closing cover 0.55 x 1.10 Mt. with Hook,

mm THk. Perforated Intermediate Partition Panel to retain

Filter Media. Wall Panel 1250/1000 x 1000 x 50 mm Thk.

with 125 mm Wide Ribbed / Champhered End connected

with Epoxy coated 12 mm Dia. Pin using Chemical Grouting

of adequate strength and Mortar Joint Adhesive on Ribbed

Edge surface. 8 Set each of 50 mm dia uPVC bend with

Total Amount for Plumbing Works -

Total Amount for Plumbing Works -

ELECTRICAL ESTIMATE -

Point wiring for Light / Bell with 2-1.5 sq.mm & earth

wire of 1.5 sq.mm (Green) both are of ISI marked 1.1 kV

grade FRLS PVC insulated multi strand copper wires up to

10 mtr length , in below type of pipe erected with 6A

Modular type switch / bell push & accessories and earth

continuity of following type, erected on PVC /

119 Metallic/Wooden box, single mounting base frame -

covered with textured/metallic/white front plate modules

erected on / in wall / ceiling as per pipe erected, with

necessary Lamp holder/ceiling rose / H.D.Connector as

directed. (a) with medium class Rigid PVC pipe and

accessories erected flushed on wall/ceiling complete Cat. III

(f) with medium class Rigid PVC pipe and accessories

erected concealed in wall/ceiling complete Cat. III

M/S JAG DESIGNERS PVT.LTD.

ARCHITECTS -URBAN PLANNER-INTERIOR DESIGNER-PMC-REG.VALUER-ENGINEER

SR. NO. ITEM DESCRIPTION UNIT Qtty SOR RATE 2024-25 AMOUNT

Point wiring for FAN with 2-1.5 sq.mm & earth wire of

sq.mm (Green) both are of .ISI marked 1.1 kV Grade FRLS

PVC insulated multi strand copper wires up to 10 mtr length, in below

type of pipe erected with 6A Modular type switch and hum free EME

step type electronic fan regulator mounted and accessories with

earth continuity of following type erected on PVC / Metallic/Wooden

box, single mounting base frame covered with textured/metallic/white

front plate modules erected on / in wall / ceiling as per pipe erected.

with necessary ceiling rose / H.D.Connector as directed. (f) with

medium class Rigid PVC pipe and accessories erected concealed in

wall/ceiling complete

Point wiring for Individual Plug with & earth wire of

sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS

PVC insulated multi strand copper wires up to 10 mtr

length, in below type of pipe erected complete with

Modular type switch & 5 pin Plug erected on PVC /

Metallic/Wooden box covered with appropriate front plate

modules erected on / in wall / ceiling as per pipe erected Pt. 5.00 612.06

with following type of accessories. [I] For 6A Plug

and 6 a switch with 2-1.5 sq.mm Cu. Wire from nearby

switchboard/mcb db board (f) with

medium class Rigid PVC pipe and accessories erected concealed in

wall/ceiling complete CATIII

Point wiring for Individual Plug with & earth wire of

sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS

PVC insulated multi strand copper wires up to 10 mtr

length, in below type of pipe erected complete with

Modular type switch & 5 pin Plug erected on PVC /

123 Metallic/Wooden box covered with appropriate front plate Pt. 5.00 894.86

modules erected on / in wall / ceiling as per pipe erected

with following type of accessories. [II] For 16A Plug and

16 amp switch with 2-2.5 sq.mm Cu. Wire from mcb db board.(f)

with medium class Rigid PVC pipe and accessories erected

concealed in wall/ceiling complete Cat. III

Point wiring for on board Looped Plug with 6A Modular

type switch & 5 pin socket erected on PVC /

Metallic/Wooden box, single mounting base frame covered

with textured / metallic/white front plate modules erected

on / in wall / ceiling with following type accessories. Cat. III

M/S JAG DESIGNERS PVT.LTD.

ARCHITECTS -URBAN PLANNER-INTERIOR DESIGNER-PMC-REG.VALUER-ENGINEER

SR. NO. ITEM DESCRIPTION UNIT Qtty SOR RATE 2024-25 AMOUNT

Providing & erecting Switch board for Computer or

electric apparatus consisting of following modular type

accessories mounted with PVC / Metallic concealed/open

box with single mounting base frame covered with

textured/metallic /white front plate,modules erected with

125 necessary connections as directed no 3.00 1133.22

1 no. 6A/16A universal plug-switch combined.

3 nos. 6A Switch

3 nos. 6A 5 pin Plug

For Modular Type Accessories Cat. III

Providing and erecting ISI mark Medium class RIGID PVC

PIPES of following size complete to be erected on/in wall or

ceiling erected with necessary PVC fittings & Junction

boxes fixed with adhesive solution & Clamps with following

dia of pipes, in approved manner as directed (b) 25 mm

Providing and erecting ISI mark Medium class RIGID PVC

PIPES of following size complete to be erected on/in wall or

ceiling erected with necessary PVC fittings & Junction

boxes fixed with adhesive solution & Clamps with following

dia of pipes, in approved manner as directed (c) 32 mm

providing and erecting Mains with 1.1 KV grade FRLS PVC

insulated ISI marked stranded Copper conductor wire in

following type of pipe to be erected in / on wall / ceiling

128 with 2.5 sq. mm copper conductor FRLS PVC insulated mtr 40.00 140.39

stranded wire of green colour for earth continuity of

following size (A) with medium class Rigid PVC pipe and

accessories (a) 2 wire 4 sq. mm

Providing and erecting Mains with 1.1 KV grade FRLS PVC

insulated ISI marked stranded Copper conductor wire in

following type of pipe to be erected concealed in /flushed

on wall/ceiling, with 1.5 sq. mm copper conductor FRLS

PVC insulated stranded wire of green colour for earth

continuity of following size (A) With medium class Rigid PVC

pipe and accessories (b) 2 wire 2.5 sq. mm

Providing and erecting Sheet Steel powder coated MCB

distribution board - flush / surface mounted fitted with

busbar, neutral link, earth bar and DIN rail, Conforms to IS

8623-1 & 3, IEC 61439-1 & 3 without MCB to house

130 appropriate nos. of MCBs.(The DBs should be used of same Ea. 1.00 1492.78

company of MCB to be used) suitable for (A) single phase

incoming and horizontal single phase outgoing (b) sheet steel

double door (IP-43) (iv)12 way

M/S JAG DESIGNERS PVT.LTD.

ARCHITECTS -URBAN PLANNER-INTERIOR DESIGNER-PMC-REG.VALUER-ENGINEER

SR. NO. ITEM DESCRIPTION UNIT Qtty SOR RATE 2024-25 AMOUNT

Providing and erecting Sheet Steel powder coated MCB

distribution board - flush / surface mounted fitted with

busbar, neutral link, earth bar and DIN rail, Conforms to IS

8623-1 & 3, IEC 61439-1 & 3 without MCB to house

131 appropriate nos. of MCBs.(The DBs should be used of same Ea. 1.00 1152.41

company of MCB to be used) suitable for (A) single phase

incoming and horizontal single phase outgoing (b) sheet steel

double door (IP-43) (iii)8 way

providing and erecting Miniature circuit breaker single pole

0.5A to 2A system and having breaking capacity 10 KA to

be erected in existing box. confirming to IS 8828/1996 with

ISI Mark Cat.III

providing and erecting Miniature circuit breaker single pole

6A to 25A suitable to operate on 240 V A.C. system and

133 having breaking capacity 10 KA to be erected in existing Ea. 16.00 123.22

box. confirming to IS 8828/1996 with ISI Mark

Providing & erecting 240 V MCB double pole switch for

motor & inductive load (C Curve) having 10 KA breaking

capacity & confirms to IS : 8828 in existing box having

following capacity

(A) 6 to 32 Amp. Cat.III Ea. 4.00 329.26

(B) 40 Amp. Cat.III Ea. 4.00 362.59

providing and erecting Approved make RCCBs conforming

to IS: 12640 and having sensitivity of 30 mA and Short

Circuit withstand capacity of 10 KA and suitable for

operation on single phase 240 V,50Hz. having characteristic

of quick action & tripping with all advance feature & do not

incorporate any electronic component. for following Max.

rating erected as directed (i) 25 Amps.DP Cat. III

providing and erecting Approved make RCCBs conforming

to IS: 12640 and having sensitivity of 30 mA and Short

Circuit withstand capacity of 10 KA and suitable for

operation on single phase 240 V,50Hz. having characteristic

of quick action & tripping with all advance feature & do not

incorporate any electronic component. for following Max.

rating erected as directed (ii) 40Amps. DP Cat. III

Providing & erecting 415V MCB Four Pole Switch for

Lighting Load (B curve) having 10KA breaking capacity &

confirms to IS :8828 in existing box having following

(b)40 Amp. Cat.III Ea. 6.00 702.96

Making trench in soft soil of suitable width of 90 cm deep

for laying cable or locating the fault all over the run and

back filling the same and making the surface as normal

M/S JAG DESIGNERS PVT.LTD.

ARCHITECTS -URBAN PLANNER-INTERIOR DESIGNER-PMC-REG.VALUER-ENGINEER

SR. NO. ITEM DESCRIPTION UNIT Qtty SOR RATE 2024-25 AMOUNT

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured

cable multistrand Aluminium conductor for 1.1 KV. to be

139 laid on wall with necessary clamps or in existing trench / Mtr. 60.00 454.50

pipe of following size of cables (D) 3 1/2 core 70 Sq. mm (

Sq. mm 1/2 core)

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured

cable multistrand / Solid Aluminium conductor for 1.1 KV.

140 to be laid on wall with necessary clamps or in existing Mtr. 350.00 168.67

trench / pipe of following size of cables (C) 4 core 10 Sq. mm

Providing and erecting FRLS-XLPE(IS:7098)(I)-88 ISI

armoured cable Aluminium conductor for 1.1 kV. to be laid

141 on wall with necessary clamps or in existing trench / pipe Mtr. 100.00 151.50

of following size of cables. (C) 2 core 10 Sq. mm

Solder less crimping type Aluminium lugs conforming to IS

suitable for cable of following size evenly crimped with

142 high pressure tool & connected to switchgear terminals Ea. 6.00 25.25

with brass/cadmium plated nut bolts in an approved

manner. (E) 70 Sq.mm.(3 NOS)

Solder less crimping type Aluminium lugs conforming to IS

suitable for cable of following size evenly crimped with

143 high pressure tool & connected to switchgear terminals Ea. 2.00 20.20

with brass/cadmium plated nut bolts in an approved

manner. (D) 35/50 Sq.mm.

Providing and, fixing heavy duty flange type brass double

compression type cable gland with rubber ring for PVC

144 insulated armoured cable complete with out going tails, Ea. 2.00 89.89

insulating tape etc for following size of cables.(B) 3 core

Providing and, fixing heavy duty flange type brass cable

gland with rubber ring for PVC insulated armoured cable

145 complete with out going tails, insulating tape etc for Ea. 34.00 38.38

following size of cables. (C) 2 to 4 core 10 Sq. mm

Providing & erecting weather proof, dust & vermin proof,

floor mounted front operated indoor type cubical panel

board necessary IP-42 and above protection as per

approval from engineer incharge made from 14 SWG thick

CRC M.S. sheet for outer body & doors, 16 SWG thick CRC

146 M.S.sheet for internal partitions with necessary accesories , -

supporting angles/ flats channel including cutting,

bending, drilling, welding, riveting with internal partitions

& cable alley as per requirements & instruction of engineer-

in-charge with erection of

M/S JAG DESIGNERS PVT.LTD.

ARCHITECTS -URBAN PLANNER-INTERIOR DESIGNER-PMC-REG.VALUER-ENGINEER

SR. NO. ITEM DESCRIPTION UNIT Qtty SOR RATE 2024-25 AMOUNT

supplied switch gears, BUSBARS, suitable size of inter

connecting PVC copper wire / copper-aluminium strips,

rubber grommets, rib, bakelite control fuses/MCB for

measuring instruments, earth bus & earth bolts,

foundation flange - bolts-base Plates, sufficient nos. of

hinged doors, handles with locking arrangement and -

rubber gasket,heavy duty end terminal connection,danger

notice board,necessary ventilation,earthing strip

complete. The Panel shall be painted with epoxy powder

(The rates excludes the cost of switchgears, bus bars, inter

connecting mains & Copper Aluminium strips, meters,

Fuses etc. The dimension shall be measured excluding base

beams) The panel shall be supplied with following

approved manufacturers with following size.

(B) The standard companies switch gear shall be used and

only manufacturers at CPRI approved factory -

(i) with 350mm depth Sq.Mtr 1.50 14902.55

Providing , erecting , fabricating the M.S. structure as per

requirement on site incorporating proper size of M.S.

angles,square,round, flats, bars, channels, sections

complete with cutting, welding, grinding & finishing duly

painted with one coat of red oxide with erection on site as

per direction of engineer in charge with necessary

grouting, cementing, plastering & finishing complete.

Supplying and erecting triple pole & neutral 440V / 500V

panel mounting Copper Busbars with four equal Nos. of

electrolyte bus having current density not more than

Amp. / sq.mm (Rated current / cross section area) duly

wrapped with colour insulating tape for phase sequence of

following current carrying capacity, erected with necessary

bus bar supports /insulators, main cable socket to each bar,

erected in existing cubical panel with necessary

(B) Suitable for 200 Amp. Capacity Rn.Mtr 1.00 3202.71

Providing and erecting Approved make Four pole moulded

case circuit breaker having breaking capacity ICU of 35 KA.

at 415 V. having Normal current rating 200A.with variable

Thermal & magnetic release suitable to work on A.C.supply

50 Hz. with all internal connections, spreader tinned

copper & complete erected in existing 16 G.M.S.housing

ICS=100% of ICU only Cat III

M/S JAG DESIGNERS PVT.LTD.

ARCHITECTS -URBAN PLANNER-INTERIOR DESIGNER-PMC-REG.VALUER-ENGINEER

SR. NO. ITEM DESCRIPTION UNIT Qtty SOR RATE 2024-25 AMOUNT

Providing and erecting Approved make Four pole moulded

case circuit breaker having breaking capacity ICU of 25 KA.

at 415 V,having normal current rating up to 25 A to 100A.

with Fixed thermal & magnetic release suitable to work on

A.C. supply 50 Hz. with all internal connections, spreader

tinned copper & complete erected in existing 16 G.M.S.

housing. ICS=100% of ICU only Cat III

Supplying and erecting led lamps with following wattage

capacity of 220 to 240 voltage, minimum 15000 burning

hours life, 500 V in built-surge protection,Polycarbonate

diffuser, mounting suitable for E14 / E27 / B22 lamp

holders, pf >= 0.5Cat-III

(A) LED Lamps integral type, with PC diffuser suitable

(ii) 5 to 8 watts Ea 4.00 112.11

152 Cable Terminal ( ‘Plain" Type)Set of Four for -

Supplying & erecting power contactor ,AC3 duty for time

switch complete erected as per direction Cat III

Supplying & erecting approved make Digital time switch

having lithium cell 6 years operative and operate battery

backup 1 channel day clock with 14 memory programme,

suitable to operate on 240V + 5%, 16A with, floating

contacts Minimum switching setup time 1 minimum & LCD

154 display. Also comprised permanent ON/OFF switching. Ea. 1.00 3168.37

Programming switches & housed in fire proof

thermoplastic enclosure & transparent cover erected as

required with necessary connection erected as directed.

Providing and erecting Approved make Earth fault Relay

suitable to mount with inter connection suitable to

following size of moulded case circuit breaker having CT

155 ratio & MCCB rating as following along with shunt trip -

220V AC. with all internal connections & complete erected

in existing M.S.housing..

Providing & erecting Medium Voltage Danger Notice Board

156 sticker as per language suggested by engineer incharge of Ea. 1.00 26.26

standard size as per IS-2551

M/S JAG DESIGNERS PVT.LTD.

ARCHITECTS -URBAN PLANNER-INTERIOR DESIGNER-PMC-REG.VALUER-ENGINEER

SR. NO. ITEM DESCRIPTION UNIT Qtty SOR RATE 2024-25 AMOUNT

providing and erecting Mains with ISI marked, 1.5kV grade

electrolyte multi stranded, annealed copper conductor

with heat resistant PVC insulated conforms to IS 694, IEC -

227 erected in existing pipe of following size (Specifically

for control panel, relays, power switchgears, motor starters

& control wiring) with required size of copper lugs, nuts

and bolts if required.

(b) One wire 1.50 sq. mm Mtr. 5.00 22.22

(c) One wire 2.50 sq. mm Mtr. 5.00 34.34

(e) One wire 6.00 sq. mm Mtr. 5.00 70.70

Providing and erecting multifunctional meter suitable for

application of Power monitoring and showing

measurement of following Voltage, Frequency, Apparent

energy, Apparent power, Active and reactive energy, Active

and reactive power, Average voltage Vavg, Peak demand

power PM, QM, SM, Demand power P, Q, S, Apparent

power S, S1, S2, S3, Unbalance current, Power factor and

displacement PF (signed, four quadrant), Calculated neutral

current, Active, reactive, apparent energy (signed, four

quadrant), Active power P, P1, P2, P3, Voltage U21, U32,

U13, V1, V2, V3, Phase currents, Average current Iag, Peak

demand currents, Reactive power Q, Q1, Q2, Q3, Demand

current I1, I2, I3, [Us] rated supply voltage 40...300 V AC

45...65 Hz, 40...300 V DC, Network frequency 50 Hz, Type

of network 3P, Display type 7 segments LED, Display colour

Red, Messages display capacity 3 fields of 4 characters,

Display digits 12 digit(s) - 14.2 mm in height

Providing and fixing printed instruction chart both in

English and Gujarati and duly framed with front glasses, for

treatment of person suffering from Electric shock with

minimum 50" diagonally size.

M/S JAG DESIGNERS PVT.LTD.

ARCHITECTS -URBAN PLANNER-INTERIOR DESIGNER-PMC-REG.VALUER-ENGINEER

SR. NO. ITEM DESCRIPTION UNIT Qtty SOR RATE 2024-25 AMOUNT

Supplying and erecting LED indoor fittings with LEDs of

wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB,

with housing used as a heat sink shall be made of thick

sheet Steel conforming to IS: 513/CRCA/ aluminium die

cast powder coated and high U.V. & corrosion resistance

with diffuser with company mark/name 160V to 270V,

Power Factor more than 0.95, THD < 15%,

Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below

description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage capacity

between the ranges shown.) (A) Tube Light with integral driver

(iv) 22-24 Watts, Surge - 2KV,IP-20, conventional 4 feet Cat-lll

Supplying and erecting LED indoor fittings with LEDs of

wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB,

with housing used as a heat sink shall be made of thick

sheet Steel conforming to IS: 513/CRCA/aluminium

pressure die cast powder coated and high U.V. & corrosion

resistance with diffuser housed in aluminium casted body

with company mark/name

160V to 270V,Power Factor more than 0.95, THD < 15 %,

CCT 3000 K to 6500K,

161 Luminaire efficacy> 85 lumens/watt , no 5.00 220.18

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below

description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage capacity

between the ranges shown.) (A) Square/ Circular shaped

Surface/Recessed Mount Downlight with provision for spring loaded

mounting clips complete.IP20 (i) 5-9 watts,Surge-2 KV Cat-lll

M/S JAG DESIGNERS PVT.LTD.

ARCHITECTS -URBAN PLANNER-INTERIOR DESIGNER-PMC-REG.VALUER-ENGINEER

SR. NO. ITEM DESCRIPTION UNIT Qtty SOR RATE 2024-25 AMOUNT

Supplying and erecting LED indoor fittings with LEDs of

wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB,

with housing used as a heat sink shall be made of thick

sheet Steel conforming to IS: 513/CRCA/aluminium

pressure die cast powder coated and high U.V. & corrosion

resistance with diffuser housed in aluminium casted body

with company mark/name

160V to 270V,Power Factor more than 0.95, THD < 15 %,

CCT 3000 K to 6500K,

162 Luminaire efficacy> 85 lumens/watt , no 15.00 589.84

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below

description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage capacity

between the ranges shown.) (A) Square/ Circular shaped

Surface/Recessed Mount Downlight with provision for spring loaded

mounting clips complete.IP20 (iii) 16-20 watts, Surge-2 KV Cat-lll

Supplying and erecting LED street light / Flood light fittings

with High power White LEDs wattage of 3 Watt and above

assembled on single MCPCB, efficiency more than

lm/w and corrosion free High pressure die cast aluminum

housing with smooth finish powder coated and heat sink

extruded aluminium with diffuser and Polycarbonate

optics/ lenses, with toughened glass with company

mark/name engraved or embossed 160 to 270 V,Power

Factor more than 0.95, THD < 10 %, CCT 3000 K to

163 5700K,Uniformity ratio >0.45, Luminaire efficacy> 100 no 30.00 4248.06

lumens/watt . LED driver efficiency > 85 %.( fittings

required LM-79 & LM-80 certificates)(NOTE: Below

description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage

capacity between the ranges shown.) (A) Street Light (IP-65),

Surge protection -4KV integral and ,Light must have 440VAC line

supply with over-voltage protection. (ii) above 48 to 59 Watts Cat-

M/S JAG DESIGNERS PVT.LTD.

ARCHITECTS -URBAN PLANNER-INTERIOR DESIGNER-PMC-REG.VALUER-ENGINEER

SR. NO. ITEM DESCRIPTION UNIT Qtty SOR RATE 2024-25 AMOUNT

Supplying and erecting LED street light / Flood light fittings

with High power White LEDs wattage of 3 Watt and above

assembled on single MCPCB, efficiency more than

lm/w and corrosion free High pressure die cast aluminum

housing with smooth finish powder coated and heat sink

extruded aluminium with diffuser and Polycarbonate

optics/ lenses, with toughened glass with company

mark/name engraved or embossed 160 to 270 V,Power

Factor more than 0.95, THD < 10 %, CCT 3000 K to

164 5700K,Uniformity ratio >0.45, Luminaire efficacy> 100 no 4.00 6177.16

lumens/watt . LED driver efficiency > 85 %.( fittings

required LM-79 & LM-80 certificates)(NOTE: Below

description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage

capacity between the ranges shown.) (B) Flood Light (IP-65),

Surge protection -4KV integral and ,Light must have 440VAC line

supply with over-voltage protection. (iv) 90 - 119 watts Cat-lll

Supplying & erecting single phase approved make industrial exhaust

fan suitable for medium duty ring mounted low noise operation

suitable for medium duty having following dia size and maximum

[A] 305 mm dia 900 RPM Cat.II

Providing suitable M.S. louver shutter of the Exhaust fan.

Supply, Installation, Testing and Commissioning of suitable

sweep, BEE 5 Star rated, Ceiling fan with Brush Less Direct

Current (BLDC) permanent ferrite magnet Motor, class of

insulation: B, Rust free 3 nos.Aluminium blades, 2 nos.

canopies, shackle kit with earthing provision, copper

winding, Power factor not < 0.9, Service Value (CMM/W)

minimum 6.85, Air delivery minimum 215 CMM,

RPM,230v (tolerance as per IS : 374-2019), THD < 10%,

167 with remote unit for Speed Control and all remaining Ea. 4.00 2885.57

accessories including safety pin, nut bolts, washers,

temperature rise = 75 °C (Max.), suitable for 140 to

Voltage and rectifier circuit with surge, over current and

overload protection , 50 Hz, Single phase AC Supply,

earthing etc. Complete as required.[ Make shall be

approved by Engineer in Charge] (B) 1200 mm Sweep (48")

Supplying and erecting 19 / 20 mm. nominal bore Medium

Class M.S. Pipe down rod erected duly painted for fan

complete with proper insulation without leakage and

M/S JAG DESIGNERS PVT.LTD.

ARCHITECTS -URBAN PLANNER-INTERIOR DESIGNER-PMC-REG.VALUER-ENGINEER

SR. NO. ITEM DESCRIPTION UNIT Qtty SOR RATE 2024-25 AMOUNT

Supplying & erecting Fan Hook of 10 mm M.S. Round bar

169 grouted in RCC slab with Making the site as original. Ea. 4.00 43.43

Supplying & erecting fan hook box of 10 mm M.S. round

bar bounded to the RCC bars up to 50mm length each side

170 and pierced through a 16 Gauge M.S. box / Heavy Duty Ea. 4.00 108.07

PVC box complete erected concealed in Ceiling with

necessary finishing.

Providing Fan clamp of 30 x 5 mm flat of required length &

171 10 mm M.S. Bolt & Nuts erected with necessary hook of 10 Ea. 4.00 98.98

mm M.S. Round Bar.

Providing 2.5mm.thick laminated acrylic sheet to cover the

fan hook or Fan box.

Supplying and erecting approved make Conical Pole (Standard ) Made

from HR sheet steel. The pole should be made as per IS. and shall be

coated with hot dip galvanizing as per IS 2629/2633/4759 with

required base plate and integral Junction box consist of terminal plate

of min 6mm Hylam sheet, standard profile 35mmX7.5mm Din-Rail for

173 MCB Mounting, stud type terminal and arrangement for cable No. 15.00 8756.70

terminationas erected on suitable foundation (included) with

necessary GI nut-bolts/J-Bolts. as per details given by manufacturer

considering site requirement.The length of poles are as below.

(D) 6 Mtr. Long 65mm Top X155 mm bottom dia, 3mm thickness.

Providing FRP/GRP arm bracket of having 15˚ arm with

174 mm OD pipe *5 mm thk,1000mm long from pole centre -

(B) Double arm bracket Ea 15.00 2776.49

Supplying & erecting approved make SMC press moulded

composite FRP. loop-in, loop-out approx. 2mm thick box

complete with Bakelite connector strip 5way(3P+N+E),DIN

rail for mounting mob & hinged doors as per requirement

having locking arrangements with mounting clamp with

nuts, bolts & washers suitable for erection on pole with

cable clamps& earth bolt of following size of box.

(B) 250mm x 200mm x 100mm [deep] Ea 15.00 515.10

Providing and erecting Pipe type earthing having

cms.long and 2.5 cms. dia. galvanised iron pipe with

coupling and buch buried in specially prepared earth pit

complete with necessary 8 SWG earth wire.

For using salt and charcoal / coke as required for pipe type

M/S JAG DESIGNERS PVT.LTD.

ARCHITECTS -URBAN PLANNER-INTERIOR DESIGNER-PMC-REG.VALUER-ENGINEER

SR. NO. ITEM DESCRIPTION UNIT Qtty SOR RATE 2024-25 AMOUNT

Supplying & erecting earth pit of minimum bore

dia.150mm size approved make Earthing Electrode

consisting Pipe-in-Pipe Technology as per IS 3043-1987

made of corrosion free hot dipped G.I.Pipes having Outer

pipe dia of 50mm having 80-200 Micron galvanising, Inner

pipe dia of 25 mm having 200-250 Micron galvanising,

connection terminal dia of 12mm with constant ohmic

value surrounded by highly conductive compound with

high charge dissipation suitable for following type of

applications with chamber and heavy duty cover.

(A)(approved make OEM has to submit test certificate

including value of earth resistance of installation duly

stamped and signed by agency and officer Incharge has to

ensure the value of earthing resistane mentioned in test

Certificate) & having back filling compound of (B) Inner

chemical (CCM Compound)- Resistivity:- 0.2 ohm / meter

testing as per IEC 62561-2017, Voltage drop:- < 1 volt at no

load & dry form, Sulphar content:- <2%(C) Back fill

Compound :- Earthing compound should be capable to

retain moisture for long time Necessary test report must

be submitted by Agency.

(b)For Electrical installation up to 11 kV in normal soil.

Length of Pipe : 2.00 mtrs

Back filling Compound :1 no. Bag of 25 Kg.

Providing and erecting HOT deep Galvanised iron strip wire

Telephone Outlet Point

SITC OF PowerCat 6 DataGate Jack, 568A/B - Yellow with Dust Cover /

Blank/ One Telephone Point to be done with Cat -6 Information

outlet Socket, Back Box, Face Plate for all telephone point. Average

181 Length to be considered as 50 Meter. Cable Laying, Labling, Ferrule, no 3.00 160.59

Testing, Certification to be included in cost. 20 Years of Certification is

required. Test reports of Level-4 Scanners only. (3) Two Pin/RJ-11

Telephone Socket [A] For One Gang Cat.III

Providing following type of Modular Type Accessories

mounted with PVC / metallic/Wooden box, single mounting

base frame covered with textured / metallic/white front

182 plate , modules erected with necessary connections as per no 3.00 160.59

site situation directed by Engineer In charge. (8) Computer

RJ-45 socket Cat.III

SITC of Patch Panel Cat 6 UTP Keystone Type- 24 Port-Fully

Loaded [Approved by Competent Authority i.e. not Below

the rank of Executive Engineer ]

M/S JAG DESIGNERS PVT.LTD.

ARCHITECTS -URBAN PLANNER-INTERIOR DESIGNER-PMC-REG.VALUER-ENGINEER

SR. NO. ITEM DESCRIPTION UNIT Qtty SOR RATE 2024-25 AMOUNT

Supply, Installation, Testing & Commissioning of Network TDN IR Mini

Dome Camera, 1/2.9" CMOS, 5 MP @ 25fps, Triple stream, Min.

Illumination required 0.25 lux @ color, WDR 120dB, Min. Pixels

x 1920, Shutter Speed 1/30000 - 1/5; Adavance Video Compression

technology such as H.265 / H.264 / MJPEG, 3mm~8mm, MFZ lens,

HLC, 3DNR, Minimum Edge Intelligence Video Analytics: Motion

184 Detection, Camera Tampering, Intrusion/Object enter area; 4 nos Nos. 1.00 24711.67

Privacy Mask, Smart IR with upto 30m IR distance, AES-128/256, PCI

Data Security Standard compliance, 128GB SD card support, DC12V,

PoE (IEEE 802.3af) (Class 2), IP 66, IK10, Having Operating temp range

: –10°C to 50° C. Certifications: ONVIF Profile S, G compliant, UL,

CE/EN, FCC Part 15 & RoHS compliant along with mounting brackets

suitable for Cieling / Wall mounting & required accesories as per site

Supply, Installation, Testing & Commissioning of 5MP IP

Network TDN IR Bullet Camera, 1/2.8" CMOS, 5 MP @

25fps, Triple stream, Min. Illumination required 0.05 lux @

F1.4 (color), WDR>120dB, Min. Pixels 2560 x 1920, Shutter

Speed 1/30000 - 1/30; Adavance Video Compression

technology such as H.265 HEVC / H.264 / MJPEG, Smart

Codec, 2.7-13.5 mm 5X motorized focus & zoom lens, P-

IRIS, HLC, 3DNR, Minimum Edge Intelligence Video

Analytics: Motion Detection, Video Tampering, Intrusion,

Loiter, Line crossing, Unattended object, Missing object,

Face detection; 5 nos Privacy Mask, 4 IR LEDs Smart IR with

upto 60m IR distance, Stream encryption, AES-128/256, PCI

Data Security Standard compliance, FIPS Chipset Built-In,

256GB SD card support with SD card encryption, Dual

channel Audio G.711a / G.711 Mu / G.726, Alarm: 2 In/

1out, In-built Heater; PoE+ (802.3 at) and 12V DC/24V AV;

IP 66 / IP 67 / NEMA 4X, IK10, Having Operating temp

range : –40°C to 60° C. Certifications: ONVIF Profile S, G

compliant, UL, CE (EN 50130-4 & EN 55032) , FCC Part 15 &

RoHS compliant along with mounting Brackets suitable for

Pole / Wall mounting & required accesories.

SITC of 32 Channel NVR having features smart

H.265+/H.265/ Smart H.264/H2.64/MJPEG, Max 320 Mbps

incoming Bandingwidth, support min 2 SATA HDDs Slot -

each slot supporting min 8TB, Up to 12 MO Resolution for

Preview and Playback and with 8 TB Survellance Hard Disk

Supply, Installation, testing and commissioning of Intel

Core i5 12C Processor 25M Cache, up to 4.90 GHz / 16GB

DDR5 / 512 SSD / Win 10 Pro Operating System / No

Monitor / DVD RW / 3 Yrs NBD / PS 500W/ NVIDIA T600

GB GDDR6 Workstation Graphics Card including 4 mDP to

M/S JAG DESIGNERS PVT.LTD.

ARCHITECTS -URBAN PLANNER-INTERIOR DESIGNER-PMC-REG.VALUER-ENGINEER

SR. NO. ITEM DESCRIPTION UNIT Qtty SOR RATE 2024-25 AMOUNT

SITC of 32 Inch 500 NTS Brightness professional Display

with Direct-Type LED, Viewing Angle : 178 Degree Verti,

178 Degree Hor. Operation 27x7, Native Resolution 3840 x

2160 (16:9) - UHD, 4 x USB (2 x 2.0, 1 x 2.0 internal, 1 x

Type C), 0-40°C, ≤0.5 W, HTML 5 Browser Opera(4.9),

Yes(internal) IEEE 802.11 a/b/g/n Dual

WiFi certificated, BIS, YES CLASS A 3dB margin. (Including

Five year free maintenance with guarantee)

Networking Enclosures & Accessories Supply, Installation,

Testing & Com mission ingot 9U Wall mount closed rack

with front glass door, fan tray on top, perforated rear

189 doors, keyboard tray with shelf. Casters & 2 nos vertical No. 1.00 21487.75

power strip with std etc as required.

Supply, Installation, Testing And Commissioning of Layer

Managed Gigabit POE switch with 24 # 10/100/1000BaseT

ports and 2 # Gigabit Combo ports(RJ45/SFP), 2 # Gigabit

Supplying & erecting approved make LAN cable of

191 following size in existing pipe as per direction Mtrs. 650.00 47.47

Supplying and erecting approved make online Un-interruptible Power

Supply system comprising flat cum-boost charger with IGBT base

rectifier & Inverter & sealed maintenance free SMF batteries. The

charger having operating capacity for input 160-270V AC & inverter

having output 230V,50 Hz Ac with 0.8 load power factor with

192 battery, over/under voltage output with over load & short circuit no 1.00 130103.15

protection equipment. The system housed in CRC sheet duly powder

coated paint with following power backup.with MS painted batteries

stand, 10% Overload capacity for momentary load.

(D) 5 KVA with 1Hr Backup

Supplying & erecting carbon dioxide (CO2) fire extinguisher user of

193 following capacity with necessary clamps made from 50 x 6 mm M.S. no 2.00 6591.26

Flat with nut & bolts grouted in wall complete.

[A] For 4.5 Kg Capacity

Providing & laying approved make Double walled

corrugated pipes (DWC) of polyethylene(conforming to IS

14930 II )with necessary connecting accessories of same

material at required depth in existing trench for laying of

cable. below ground / road surface for enclosing cable

(A)50 mm outer dia

M/S JAG DESIGNERS PVT.LTD.

ARCHITECTS -URBAN PLANNER-INTERIOR DESIGNER-PMC-REG.VALUER-ENGINEER

SR. NO. ITEM DESCRIPTION UNIT Qtty SOR RATE 2024-25 AMOUNT

M/S JAG DESIGNERS PVT.LTD.

ARCHITECTS -URBAN PLANNER-INTERIOR DESIGNER-PMC-REG.VALUER-ENGINEER