CA No CE CHZ AMB T 04 2023 24 ADDITION ALTERATION UPGRADATION AND CONNECTED WKS OF OFFRS JCOS AND OR MD ACCN AT AMBALA CANTT

Amount

ITEM NO. 1 : Cutting openings, through brick walls built in cement mortar for door, window and other openings or enlarging existing openings, converting window into door openings etc. or cutting out defective brick work for under- pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc and rubbish not exc. 50 m from site complete all as specified and directed by Engineer-in-Charge.

ITEM NO. 2 : Taking down Cement plaster or cement lime plaster on brick or stone walls including raking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge.

ITEM NO.3 : Demolition of cement concrete (reinforced) (reinforcement cut as required to facilitate demolition) as in roofs, floors (other than ground floors) beams, slabs, staircases, landing, chajjas and similar suspended work complete all as specified and directed by Engineer-in-Charge.

ITEM NO.4 : Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

ITEM NO.5 : Demolition of Cement concrete unreinforced as in Ground Floor and paving n. exc. 15cm thick (above or below G.L.) complete including disposal of unservicable rubbish outside Cantt area complete all as specified and directed by Engineer-in-Charge.

ITEM NO.6 : Demolition of Cement concrete (any type) for existing sunken portion of WC/floor trap including removing of all debris from site to cleanings distance exc 250m but n. exc 500m and deposited where directed including clearing of surface with wire brushes and water complete all as specified and directed by Engineer-in-Charge.

ITEM NO.7 : Taking down chowkhats or frames n.exc 1.5 sqm each (without taking off shutter from the frame) and removing from the site including dismantling brick work for hold fasts etc complete, all as specified and directed by Engineer-in-Charge.

ITEM NO.8 : Taking down chowkhats or frames exc 1.5 sqm but n.exc 4 sqm each (without taking off shutter from the frame) and removing from the site including dismantling brick work for hold fasts etc complete all as specified and directed by Engineer-in-Charge.

ITEM NO.9 : Taking down shutters of any description n exc 1 Sqm each and removing from the site complete all as specified and directed by Engineer-in-Charge.

ITEM NO.10 : Taking down shutters of any description exc 1 Sqm and not exc 2 Sqm each and removing from the site complete, all as specified and directed by Engineer-in-Charge.

ITEM NO.11 : Dismanting of stucturel steel work including doors, gates but excluding framed truss etc complete all as specified and directed by Engineer-in-Charge.

ITEM NO.12 : Dismantling wooden boarding any description, fixed in any position with nails as in shelves of cup board and pelmets of any description complete all as specified and directed by Engineer-in-Charge.

ITEM NO.13 : Running welding in repairs to hinges of steel window/pressed steel door and making good for opening of doors/window shutters thickness of metal to be welded exc 6 mm but n.exc 9 mm complete all as specified and directed by Engineer-in-Charge.

ITEM NO.14 : Taking down of Eaves gutter/rain water pipe( AC rain water pipe /SWG pipe line of any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fitting and accessories) complete all as specified and directed by Engineer-in-Charge.

ITEM NO.15 : Demolition and breaking up 150 mm bore drain pipes (salt glazed stone ware pipes) set in cement mortar complete all as specified and directed by Engineer-in-Charge.

ITEM NO.16 : Taking up or down steel tubing and connections of 15mm bore in pipe, including cleaning for re-fixing or removal from site to store complete all as specified and directed by Engineer-in-Charge.

ITEM NO.17 : Taking up or down steel tubing and connections of 20mm bore in pipe, including cleaning for re-fixing or removal from site to store complete all as specified and directed by Engineer-in-Charge.

ITEM NO.18 : Dismantling of cast iron or RCC drain pipes 100 mm bore jointed in cement mortar from floors/walls etc. and taking out from trenches if required complete all as specified and directed by Engineer-in-Charge.

ITEM NO.19 : Dismantling of cast iron or RCC drain pipes 75 mm bore jointed in cement mortar from floors/walls etc. and taking out from trenches if required complete all as specified and directed by Engineer-in-Charge.

ITEM NO.20 : Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed Conduit(TV/Tele Socket) etc., and making good, cutting not exc 10cm girth and complete, all as specified and directed by Engineer-in-Charge.

ITEM NO.21 : Disconnecting existing tanks of capacity 500 litre setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position.(cleaning repairing etc measured separately) complete all as specified and directed by Engineer-in-Charge.

ITEM NO.22 : Demolition of brick work built in cement mortar including all quions arches, pillar or any other description etc complete all as specified and directed by Engineer-in-Charge.

ITEM NO.23 Demolition of cement concrete (reinforced) of any description and in any position including cutting of reinforcement complete all as specified and directed by Engineer in Charge.

ITEM NO.24 : Dismantling of brick or terracing tiles of single layers on roofs incl cleaning of bricks/tiles and removal of unusable bricks/tiles from site, complete all as specified and directed by Engineer-in-Charge.

ITEM NO.25 : Demolition of mud roof any thickness (whether full thickness removed or part thereof ) including plastering & leaping complete, all as specified and directed by Engineer-in-Charge.

ITEM NO.26 :Dismantlling Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings in any position complete all as specified and directed by Engineer in Charge.

ITEM NO.27 : Supplying & fixing of PVC water storage tank 500 ltr capacity HDPE triple layered ,white colour cylindrical type fixed and hoisted in position on roof at any height complete with inlet/outlet of 20 mm GI Pipe connection incl locking arrangement, including supplying & fixing of Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe 20 mm dia and (Minimum weight 200 gm - 210 gms ) including dismantling old unserviceable cement concrete/PVC water tanks of capacity exc 250 ltrs & n.exc 500 Ltrs complete all as specified and directed by Engineer-in-Charge. Note : (i) Inlet, outlet & wash out pipe will be measured and paid for separately. (ii) The quoted rate is inclusive of minimum one union each on inlet and outlet of water tank as per size of pipe shall be provided.

ITEM NO.28 : Broken stone hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n.exc. 15 cm thick, watered and rammed to a true surface complete & all as specified.

ITEM NO.29 : 25 mm thick Cement concrete (1:2:4) type B-0,using 12.5 mm graded mechanically crushed stone aggregate as in sub - floors, sub bases finished even & rough to receive the topping layer. complete all as specified and directed by Engineer-in-Charge.

ITEM NO. 30 : 100 mm thick, cement concrete 1:4:8 type D2 using 40 mm graded mechanically crushed stone aggregate, as in Sub-Base, complete and all as specified

ITEM NO. 31 : 75 mm thick, cement concrete type C-2, 1:3:6 using 40 mm graded mechanically crushed stone aggregate, finished even & smooth without using extra cement, as in plinth protection / path complete all as specified and directed by Engineer In Charge.

ITEM NO. 32 : Cement concrete 75 mm thick 1 :2 4 type B 2 using 40 mm graded mechanically crushedcrushed stone aggregate as in flooring and finishing cement concrete surface even and fair with out using extra cement, to be laid in alternate panels complete all as specified and directed by Engineer In Charge.

ITEM NO. 33 : 40 mm thick cement concrete 1:2:4 type B 1 (20 mm graded mechanically crushed stone aggregate) as in PCC flooring and finishing concrete surface even and smooth without using extra cement complete all as specified and directed.

ITEM NO.34 : Plain cement concrete (1:3:6) type C-1,using 20 mm graded mechanically crushed stone aggregate as in filling of pressed steel frame /hold fast blocks etc and similar complete all as specified and directed by Engineer-in-Charge.

ITEM NO.35 : Plain cement concrete (1:4:8) type D-2,using 40 mm graded mechnically crushed stone aggregate as in foundations, filling and mass concrete complete all as specified and directed by Engineer-in-Charge.

ITEM NO.36 : Reinforced cement concrete pipes. 150mm bore NP3 laid in trenches to any depth including jointing materials and testing complete all as specified and directed by Engineer-in-charge Note : Excavation and earth work and concrete for bed and haunching of pipe shall be measured and paid seperatively.

ITEM NO. 37 : Concrete bed to drain pipes of 100 mm bore including packing under and hauching against the sides of pipes after they are laid and tested in PCC 1:3:6 type C2 complete all as specified and directed by Engineer in charge.

ITEM NO. 38 : Concrete bed to drain pipes of 150mm bore including packing under and hauching against the sides of pipes after they are laid and tested in PCC 1:3:6 type C2 complete all as specified and directed by Engineer in charge.

ITEM NO.39 : Plain cement concrete 1:2:4 type B-0 using 12.5mm graded mechnical crushed stone aggregate as in roof kerbs or mud stops and benching, rounded or chamfered on edges , coving shall be 150 mm in radius mixed with acrylic based polymer water proofing compound complete all as specified and directed by Engineer-in-Charge. Note : WPC shall be paid separately.

ITEM NO.40 : Plain Cement concrete 1:2:4 type B-1 using 20mm mechanically graded crushed stone aggregate as in padding to roof to maintain the required slope and finished the surface even and smooth without using extra cement including weathering, slightly rounded or chamfered angles and throating with and including using necessary use and waste of formwork for fair finished surface complete all as specified and directed by Engineer-in-Charge.

ITEM NO.41 : Plain cement concrete 1:2:4 type B-1 using 20mm graded mechanically crushed stone aggregate as , copings, and, benching including using necessary use and waste of formwork for fair finished surface complete all as specified and directed by Engineer-in-Charge.

ITEM NO.42 : Plain cement concrete 1:3:6 type C-1 using 20mm graded mechanically crushed stone aggregate as in surface channel or drain including using necessary use and waste of formwork for fair finished surface complete all as specified and directed by Engineer-in-Charge.

Item No 43 : Plain cement concrete 1:2:4 type B-2 using 20mm graded mechanically crushed stone aggregate as in surface channel or drain including using necessary use and waste of formwork for fair finished surface complete all as specified and directed by Engineer-in-Charge.

ITEM NO.44 : Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped end etc. complete all as specified and directed by Engineer-in-Charge. NOTE: Inner girth only be measured and paid.

ITEM NO.45 : Reinforced Cement Concrete M-25 Design mix using 20mm graded mechanically crushed stone aggregate as in chajjas and the like complete all as specified and directed by Engineer-in-Charge.

ITEM NO.46 :Reinforced Cement Concrete M-25 Design mix using 20mm graded mechanically crushed stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed by Engineer-in-Charge.

ITEM NO.47 : Reinforced Cement Concrete M-25 Design Mix using 20mm graded mechanically crushed stone aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m complete all as specified and directed by Engineer-in-Charge..

ITEM NO.48 : Use & waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. (rough finished flat surfaces of concrete), complete all as specified and directed by Engineer-in-Charge.

ITEM NO.49 : Use & waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings , slab over manholes similar work; not exceeding 200mm thick (Horizontal or sloping) (fair finished flat surfaces of concrete), complete, all as specified and directed by Engineer-in-Charge.

ITEM NO.50 : Use & waste of Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers , shelves including supports,overhangs etc also splays between floor & beams etc for flat rough finished complete all as specified and directed by Engineer-in-Charge.

ITEM NO.51 : Use and waste of form work to Chullah hoods, chajjas, troughs and similar items including edges for rough finish surfaces complete all as specified and directed by Engineer-in-Charge.

ITEM NO.52 : Use & waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n.exc 20cm wide (fair finished surfaces of concrete), complete, all as specified and directed by Engineer-in-Charge.

ITEM NO.53 : TMT steel bars 10mm dia and over, of grade Fe-500D cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete, all as specified and directed by Engineer-in-Charge.

ITEM NO.54 : TMT steel bars 6 to 8 mm dia, of grade Fe-500D cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.

ITEM NO.55 : TMT steel bars 5mm dia and over upto and including 10mm dia , of grade Fe-500D cut to length, bent to shape required, including cranking, bending stirrups spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips as in strirrups , spacers and binders complete all as specified and directed by Engineer-in-Charge.

ITEM NO.57 : First quality, Non skid ceramic, coloured, rectified i.e. straight edge (locally known as joint free) area of each tiles exceeding 0.18 sqm but not exceeding 38 sqm and of thickness 7 to 8 mm, in verical surfaces such as skirtings, dados and risers to steps etc (by cutting the tiles to required height). over including 10 mm thick cement mortar (1:4) rendering, set and jointed with tile adhesive with notched trowel and pointed in grout of matching shade of tiles, complete all as specified and directed by Engineer-in-Charge.

ITEM NO.58 : First quality Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors etc. set and jointed in neat cement mortar over and including 15 mm thick screed in cement mortar (1:6) and pointed in white or coloured cement to match the tiles complete all as specified and directed by Engineer-in-Charge.

ITEM NO.59 : Glazed ceramic coloured tiles 450mm x 300mm & 7mm thick on vertical surface such as skirting , dado etc. over and including 10 mm thick rendering in CM 1:4 thick set and jointed in neat cement mortar and pointed in white or colour cement to match tiles complete all as specified and directed by Engineer-in-Charge.

ITEM NO.62 : Baroda Green marble, 15-18mm thick, machine cut, laid over & including 15mm bedded and jointed with adhesive suitable for granite/stone & pointed with grout of matching shade including necessary cutting over & including 15mm thick (average thickness) rendering cement morar (1:4) as in riser/skiriting of Stair case complete, all as specified and directed by Engineer-in-Charge.

ITEM NO.63 : Providing cement concrete 1:2:4 type B1 in lintel upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lancing courses, parapets and railings upto 60cm in height, coping, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete, all as specified and directed by Engineer-in-Charge.

ITEM NO.64 : Machine cut Kota stone slab flooring 16-18 mm thick, laid over & including 20 mm thick screed bed in cement mortar 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (mirror finish) complete all as specified and directed by Engineer-in-Charge.

ITEM NO.65 : Machine cut Kota stone slab 16-18 mm thick as in skirting, dado and pillars etc , laid over & including 10 mm thick rendering in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the existing surfaces including rubbing and polishing (mirror finish) complete all as specified and directed by Engineer-in-Charge.

ITEM NO.66 : Granite jet black shade, 15-18 mm thick, (table rubbed and polished) machine cut, machine polished, bedded and jointed with adhesive suitable for granite/stone & pointed with grout of matching shade including necessary cutting over & including 15 mm thick (average thickness) cement mortar (1:4) screed, as in cooking platform, shelves, RCC counters, window cills & similar situations, complete all as specified and directed by Engineer-in-Charge.

ITEM NO.67 : Baroda green marble, 15-16 mm thick, (table rubbed and polished) machine cut, laid over & including 15 mm thick (average thickness) cement mortar (1:4) screed and bedded, jointed with grey cement slurry & pointed with grout of matching shade including rubbing and polishing (Granite finish), as in cooking platform shelves , RCC counters, window cills & similar situations complete all as specified and directed by Engineer-in-Charge. NOTE: Full round nosing if ordered on exposed edges shall be paid separately under respective item.

ITEM NO.68 : Rounding to edges of stone (of any description) slabs one edge, such as in steps, cooking platform, and other similar situations including cutting, rubbing and polishing (mirror finish), complete all as specified and directed by Engineer-in-Charge.

ITEM NO. 69 : Providing and laying of 300x300 mm & 10mm thick Anti-Skid vitrified pavement tile in approved colour & Shade in anti skid finish set and jointed in neat cement slurry and pointed in white cement & pigment to match over and including 20 mm thick screed bed in cement mortar 1:4 complete all as specified and directed by Engineer- in - Charge . (Note: Design/pattern shall be as approved by GE at the time of execution)

ITEM NO. 70 : Supply only Glass dividing strips, 3mm thick and inserted in position to conform to design width of strip 38mm complete all as specified and directed by Engineer In Charge.

ITEM NO. 71 : Supply only 4mm thick plain Asbestos cement sheet 75mm wide as in dividing strips in flooring fixed in position to conform to design all as specified and directed by Engineer In Charge.

ITEM NO.72 : Brick work with sub class 'B' bricks, class designation 100, old size bricks, straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge.

ITEM NO.73 :All as per serial item No 72 here-in-before but except bricks-ditto-

ITEM NO.74 :Supply & fixing powder coated aluminium section sliding type 3/4 track (min thickness of powder coating 50 micron) for window & ventilators including providing and fixing hinges/pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285 fixing with dash fasteners of required dia and size, including necessary fitting upthe gaps at junctions, i.e at top, bottom and sides with requred EPDM rubber/neoprene gasket etc, aluminium sections shall be smooth, rust free straight mitred and jointed mechanically wherever requred including cleat angle aluminium snap beading for glazing/paneling, C.P brass/stainless screqs and including locking arrangement and stay arrangement complete all as specified and as directed bythe engineer-in-charge. Note:- (a) Glazing shall be measured and paid separately. (b) Weight of aluminium sections shall be as per IS or actual weight which ever less shall be measured. (c) The rate quoted shall be inclusive of neoprene beading, glazing clips, jointing clips, screw and locking arrangement and stay arrangement etc as required and the same shall not be measured for arriving the weight. (d) The rate shall be inclusive of locking arrangement including complete packing with silicon gel all around contacting surface of aluminium framework and including matching the existing surface area complete all specified and directed

ITEM NO.75 : Brick work using burnt clay bricks of sub class 'B' ,class designation 75,straight or curved on plan to any radius in half brick thick walls built in cement mortar (1:4) complete all as specified and directed by Engineer-in-Charge.

ITEM NO.76 : Precast PCC plain factory made tiles, ISI marked, 22 mm thick of size 300 mm x 300 mm, machine pressed and cut polished and set jointed and pointed in neat cement slurry and fabricated using grey cement & no pigments. over and including 15 mm thick cement mortar (1:3) bedding joints grouted flush in cement mortar (1:3) mixed with integral liquid water proofing compound over roof surfaces complete all as specified and directed by Engineer-in-Charge.

ITEM NO.77 : Forming jambs, etc to openings, including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work; built in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge.

ITEM NO. 78 : Rendering 15 mm thick in cement mortar 1:6, on fair faces of brick or concrete surfaces , trowelled to even and smooth surface without using extra cement, complete all as specified and directed by Engineer-in-Charge.

ITEM NO. 79 : Supply and fixing swan neck brass chromium plated sink mixer for mixing hot & cold water for 15mm bore pipes including all connecting fittings, screwed down for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge.

ITEM NO.80 : Rendering 15 mm thick in cement mortar 1:4, on brick or concrete surfaces mixed with liquid water proofing compound, trowelled to even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge. NOTE: Water proofing compound shall be measured and paid separately.

ITEM NO.81 : Rendering 15 mm thick incement mortar 1:4 on fair faces of brick work or concrete surface of wall and finfished surface even and smooth with neeru finish to plastering complete all as specified and directed by Engr-in- charge.

ITEM NO.82 : Rough cast finish plastering over and including 10 mm thick rendering in cement mortar 1:3 and while it is still in plastic state, the rough cast mixture consisting of crushed stone or fine gravel aggregate ( of size between 6 to 12 mm ) mixed with coarse sand and cement in the ratio of 1: 1: 1 shall be applied and finished even. The mix of cement and sand shall be made slightly wetter than normal for rendering to ensure that larger aggregates are thoroughly covered complete all as specified and directed by Engineer-in-Charge. Rough cast finish plaster shall be applied as specified in clause 14.22 of SSR Part-I .

ITEM NO 83 Supply only liquid water proofing compound ISI Marked complete all as specified and directed.

ITEM NO.84 : Rendering 5 mm thick in cement mortar 1:3 as in soffits of slabs/Chajja/ Sunshade finishing the plastered surface even & smooth without using extra cement etc complete all as specified and directed by Engineer-in-Charge.

ITEM NO.85 : Dubbing out average 10mm thick on irregular surfaces of soffits of slabs/Chajja/ Sunshades etc. in CM 1:4 complete all as specified and directed by Engineer-in-Charge.

ITEM NO.87 : Preparation of new plastered or unplastered surfaces of walls rough cast plaster and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and directed by Engineer-in-Charge. (Note:- For Measurment purpose only flat surface shall be measured)

ITEM NO.88 : Complete removal of existing treatment from walls and applying two coats of cement base paint over one coat of alkali resistant primer including preparation of surfaces complete all as specified and directed by Engineer-in-Charge.

ITEM NO.89 : Preparation of new plastered surfaces of wall and applying two coats of oil bound distemper over a coat ofchalk whiting primer complete all as specified and directed by Engineer-in-Charge.

ITEM NO.90 : Providing one layer of guiniting of thickness not exceeding 50 mm provided steel reinforcement and chicken wire mesh if required by means of tinned tracks or welded to existing reinforcement in CM 1:3 for top & bottom of roof slabs, beams, columns and staircase etc as directed including scaffolding at any height all as directed including mild steel chicken wire mesh of weight exceeding 0.25 kg/sqm and but not exc. 4kg/sqm complete all as specified and directed by Engineer-in-Charge.

ITEM NO.91 : Preparation of old Plastered or un-plastered surfaces of walls cornices etc by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss, efflorescence salts treating oil and greasy spots etc and applying two coat of white wash on walls/ old decorated surfaces complete all as specified and directed by Engineer-in-Charge.

ITEM NO.92 : Preparation of old Plastered or un-plastered surfaces of ceilings etc by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss, efflorescence salts treating oil and greasy spots etc and applying two coat of white wash on ceilings/ old decorated surfaces complete all as specified and directed by Engineer-in-Charge.

ITEM NO.93 : Preparation of plastered or unplastered new surfaces of ceilings and applying three coats of white wash including preparation of surface complete all as specified and directed by Engineer-in-Charge.

ITEM NO.94 : Preparation of plastered or unplastered new surfaces of walls and applying three coats of white wash including preparation of surface complete all as specified and directed by Engineer-in-Charge.

ITEM NO. 95 : Preparation of plastered or unplastered new surfaces and applying two coats of cement base paint complete all as specified and directed.

ITEM NO. 96 : Complete removal of existing treatment and applying two coats of oil bound distemper on walls over a coat primer of chalk whitening including preparation of surfacecomplete all as specified and directed.

ITEM NO.97 : Factory made Pressed steel frames, confirming to IS, having profile 125 x 60 mm , 1.25 mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, and fixing only 100 mm size hinges, lock strike plate, etc., with one shop coat of zinc chromate primer and fixing complete all as specified and directed by Engineer-in-Charge. Note: Butt hinges shall be measured and paid separately as supply only under relevant item.

ITEM NO.98 : Factory made Pressed steel frames, confirming to IS, having profile 105 x 60 mm , 1.25 mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, and fixing only 100 mm size hinges, lock strike plate, etc., with one shop coat of zinc chromate primer and fixing complete all as specified and directed by Engineer-in-Charge. Note: Butt hinges shall be measured and paid separately as supply only under relevant item.

ITEM NO.99 : Plain, solid, straight 2nd class Hard wood chowkhats and frames, wrought, framed rebated on solid, rounded or chamferred, put together with glue pinned at joints supplied and fixed complete all as specified and directed by Engineer-in-Charge.

ITEM NO. 100 : Factory made solid PVC moulded door shutters 28 to 30mm thick (stiles) with 2:4 or 6 raised panel design with 2mm thick , prelam pvc sheet front face 2mm plain colour pvc sheet on back face with particle Board core supplying & fixing in frame at site as per specification & drawing (Wood colour) complete all as specification and directed.

ITEM NO.101 : 35 mm thick factory made glazed & Skeleton shutters of 2nd class HardWood open rebated & prepared to receive glass or gauze etc (without sash bar) open rebated with edge of framing , chamfered or rounded, fitted with cut & mitred beads for securing glass or guage etc sizes of members of shutters as specified in sec 8 clause 8.24 (a) of SSR Part-I (2009) complete all as specified and directed by Engineer-in-Charge.

ITEM NO.102 : Solid PVC door frames of size 50mm x 47 mm made out of 5mm wood grain printed PVC sheet reinforced with MS square tube, and edges will be painted to match with printed sheet, supply & fixing in opening as per specification & drawing complete, all as specified and directed by Engineer-in-Charge.

ITEM NO.103 : Material & Labour for making good under cills or over arches, lintels and bressummers, including all pinning when necessary complete, all as specified and directed by Engineer-in-Charge.

ITEM No. 104 Factory made box type steel windows with pressed steel frame complete included mild steel ascessories like lugs, door stopper, holdfasts, pintol hinges, handles (minimum One for each shutter), and ISI marked tower bolt 150 mm size (minimum 2 for each shutter)etc. with or without glazing bars dovetailed or welded with one shop coat of zinc chromate primer , complete all as shown on drawing no. TD-276 (R) SH 1/4 to 2/4 , 3/4, 4 (R) /4 Note : (i) Fabrication as per TD-276 (R) SH 1/4 to 2/4, 3/4, 4 (R) /4 (ii)Mode of measurement Unit will be in Kilogram for the complete window except Glass / wire Gauge but incl fittings, ISI marked iron mongery and Grill/ Guard bar complete as per TD. The weight of windows will be finalized by the BOO to be convened by CWE before installation. The weight shall not include PCC back filling of the chowkhat. (iii) The PCC back filling in chowkhat of window, Sheet glass and wire gauge will be measured and paid separately against respective items.

ITEM NO.105 : Factory made steel window/ ventlator fixed type (fabricated from P-tube section as shown on drawings) including necessary mild steel acessories etc. with glazing bars dovetailed or welded with one shop coat of zinc chromate primer, complete all as shown on drawing No. TD-220R Sheet 3/3.

ITEM NO.106 : Supply only stainless steel butt hinges 100 mm long medium, weight complete all as specified and directed by Engineer-in-Charge.

ITEM NO.107 :Aluminium anodised of extruded fabricated type handle of size 100 mm long complete all as specified and directed by Engineer-in-Charge.

ITEM NO.108 : Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) 300 mm long and fixing clips of sheet cast or extruded sections or cast aluminium alloy and fixed complete all as specified and directed by Engineer-in-Charge.

ITEM NO.109 : 150 mm long Aluminium anodised barrel tower bolts of extruded section complete all as specified and directed by Engineer-in-Charge.

ITEM NO.110 : 200 mm long Aluminium anodised barrel tower bolts of extruded section complete all as specified and directed by Engineer-in-Charge.

ITEM NO. 111 : Aluminium anodised extuded type , handle 150 mm long complete , all as specified and directed.

ITEM NO.112 : Mild steel Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete and conforming to Fe-410-W (Gde E-250 quality B) complete all as specified and directed by Engineer-in-Charge.

ITEM NO.113 : Mild Steel Framed work as in guard bars/grills, gratings, etc.. with ends of bars shouldered/welded and/or riveted, or forged into spikes; framed guard bars barred iron doors framed balusters, walkways ,railings frame work of water tanks and similar work ladders, conforming to Fe-290 E-165 complete all as specified and directed by Engineer-in-Charge.

ITEM NO.114 : Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staples complete all as specified and directed by Engineer-in-Charge.

ITEM NO.115 : Sheet glass 4 mm thick, ordinary quality and glazing with linseed oil pane putty & spring glazing clips using Silicon for fixing of glass in addition to glazing putty, in squares not exceeding 0.5 Sqm in each pane, complete all as specified and directed by Engineer-in-Charge.

ITEM NO.116 : 4 mm thick figured glass pin head type and glazing with oil putty in square not exc 0.5 sqm each and using Silicon for fixing of glass in addition to glazing putty complete all as specified and directed by Engineer-in-Charge.

ITEM NO.117 : Preparation of new or previously untreated wooden surface of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed by Engineer-in-Charge.

ITEM NO.118 : Preparation of newly primed surfaces and applying two of synthetic enamel paint over steel and iron surfaces of any description, not otherwise described, over 10 cm in width or girth, complete all as specified and directed by Engineer-in-Charge.

ITEM NO.119 : Preparation of new or previously untreated steel and iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-Charge.

ITEM NO.120 : Supply and fixing 4.8mm thick figured glass ordinary quality with aluminum beading, rubber packing or oil puty in square/rectangular n exc 0.5 sqm in each pane complete all as specified and directed.

ITEM NO.121 : 300 mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by Engineer-in-Charge.

ITEM NO.122 : Supply only 50 mm long cold rolled mild steel butt hinges medium weight complete all as specified and directed by Engineer-in-Charge.

ITEM NO.123 : 25mm dia stainless steel fancy type drapery rod of wall thickness 1.6 mm fixed with including stain less steel decorative brackets two Nos for each rod at both ends etc as in repairs complete all as specified and directed by Engineer-in-Charge.

ITEM NO . 124 : Mild steel works as bands , straps supports or stays for rain water ventilating pipes including both if required . hook (stay), heavy for large & staples, chains hand made sliding bolts, clamps, hold fast, wall ties hooks for hanging fans plain angle cleat for securing purlins to wood truss or rafter , knee pieces inserts two way and three ways strap, plate , washers and similar articles confirming to Fe 290 Gde E-165 complete all as specified and directed by Engineer-in-Charge. .

ITEM NO.125 : Factory made mild steel door shutter with frame, fabricated from of 1 mm thick MS sheet including provision of steel handle & locking arrangement by providing 04 lever lock with duplicate keys (of make Godrej, Link or Harrison) & handle etc, all as per Godrej pattern including spray painting over a coat of red oxide primer and fixing the same on existing cupboard nitch MS fasteners with cement & sand mortar, complete all as specified 'shown on drawing no. FD-1032 Sheet 1/1 dated 25-09-1993 and directed by Engineer-in-Charge. Note : The shutter area only should be measued for payment.

ITEM NO. 126 35mm thick Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides and complete all as specified.

ITEM NO.127 : Rubber strips 3 to 4mm thick & 65mm to 75mm wide fixed on bottom rail of door for covering gaps between door & floor to aviod entry of insects,dust etc complete all as specified and directed by Engineer-in-Charge.

ITEM NO.128 : WPC 18mm thick (Minimum density 600kg/Cum) both side plain white colour, fixed with stainless steel screws, solvent cement /adhesive to make kitchen /bed rooms cabinet sides top and bottom and shelves inside the cabinets complete as per manufacturer’s specifications complete all as specified and directed by Engineer–in–Charge

ITEM NO.129 : WPC 18mm thick (Minimum density 600kg/Cum) of single side vijid lamination of approved colour and other side plain white colour, fixed with stainless steel screws, solvent cement /adhesive to make kitchen cabinet shutters and shelves complete as per manufacturer’s specifications complete all as specified and directed by Engineer-in-Charge.

ITEM NO.130 : 12mm thick WPC (Minimum density 600kg/Cum) of fixed with stainless steel screws, solvent cement /adhesive to make wall mount kitchen cabinet back and pull out drawer sides complete as per manufacturer’s specifications complete all as specified and directed by Engineer-in-Charge.

ITEM NO.131 : Stainless steel 304 grade wire basket cutlery of size 370 x 485mm premium quality fixed in position complete all as specified and directed by Engineer–in–Charge. Make : HETTICH, KAFE , GLEN, HARRISON AND GODREJ

ITEM NO.132 : Stainless steel 304 grade wire basket (average weight 2.5 to 4 Kg per Basket) of pull out type like plain /cup & saucer /bottle /multi purpose /2–3 shelf basket etc for kitchens of required size fixed in position complete all as specified and directed by Engineer–in–Charge. Make HETTICH, KAFE , GLEN, HARRISON AND GODREJ

ITEM NO.133 :Ball bearing runners 45mm telescopic (KTS–20) full extension load capacity minimum 50Kgs complete all as specified and directed by Engr–in–Charge. Make HETTICH, KAFE , GLEN, HARRISON AND GODREJ

ITEM NO.134 : ‘D’ type cabinet handles premium quality, stainless steel grade 304, gloss chrome, SN finished 150mm long matt finished complete all as specified and directed by Engineer–in–Charge. Make HETTICH, KAFE , GLEN, HARRISON AND GODREJ

ITEM NO.135 : Auto closing hinges of size 35mm of 0 crank (KH–001) of 8 crank (KH–002) openable at 110 degree for kitchen cabinet shutters complete in all respect and fixed in position complete all as specified and directed by Engineer–in–Charge. Make HETTICH, KAFE , GLEN, HARRISON AND GODREJ

ITEM NO.136 : Small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops,cleats and the like of 2nd class Hardwood, including all necessary' labours; articles n exc 200 cu. cm each complete all as specified and directed by Engineer-in-Charge.

ITEM NO.137 : Steel water tubing, galvanised, medium grade, ISI marked, 15 mm bore with and including all fittings , cutting, threading and fixed to walls or fixing in concealed walls or laid in floors and making good the surfaces to match the existing ones complete all as specified and directed by Engineer-in-Charge.

ITEM NO.138 : Steel water tubing, galvanised, medium grade, ISI marked, 20 mm bore with and including all fittings , cutting, threading and fixed to walls or fixing in concealed walls and making good the surface to match the existing ones or laid in floors complete all as specified and directed by Engineer-in-Charge.

ITEM NO.139 : Refixing old GI tubing 15mm bore galvanised with all fittings as in walls,ceilings or floors etc complete all as specified and directed by Engineer-in-Charge.

ITEM NO.140 : Refixing old GI tubing 20mm bore galvanised with all fittings as in walls,ceilings or floors etc complete all as specified and directed by Engineer-in-Charge.

ITEM NO.141 : Supplying and fixing in repairs Vitreous china wash down water closet pan (Pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe), P or S trap, complete all as specified and directed by Engineer-in-Charge.

ITEM NO.142 : PVC water closet seat cover , white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed by Engineer-in-Charge.

ITEM NO.143: Supplying and fixing in repairs Vitreous China squatting pan of “Orissa Pattern” of size 580x440mm coloured with integral footrest complete including making goods floor all as specified and directed by Engineer-in-Charge. Note : The quoted rate shall include provision of "P" Cast Iron trap.

ITEM NO.144 : 10 ltr capacity PVC valveless, syphonic action dual flush type flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, 32 mm dia flush pipe in repairs complete all as specified and directed by Engineer-in-Charge.

ITEM NO.145 : Supply & fixing in repairs health faucet ABS body including 1.00 m long easy flex tube in chrome with finishes and wall hook complete all as specified and directed by Engineer-in-Charge'.

ITEM NO.146 : Supplying and fixing in repairs JET fighter spray with flexible arm , (suitable for European seat) complete all as specified and directed by Engineer-in-Charge.

ITEM NO.147 : Supplying and fixing in repair CP toilet paper holder with flap model complete all as specified and directed by Engineer-in-Charge.

ITEM NO.148 : Supplying and fixing in repairs pillars taps fancy type chromium plated, screwed down high pressure, with or without lettered 'Hot'or cold with cast copper alloy with capston head long screwed shanks and fly-nuts, screwed for iron pipe of 15mm bore and fixed complete all as specified and directed by Engineer-in-Charge.

ITEM NO.149 : Supplying and fixing in repairs vitreous china wash hand basin white flat back of size 550x440mm including CI brackets , chromium plated waste coupling, waste pipe etc., (including all waste fittings) complete all as specified and directed by Engineer-in-Charge.

ITEM NO 150 Supplying & fixing vitreous chinawash hand basin white flat back of size 550 x 440 mm including CI brackets, chromium plated waste coupling, waste pipe etc (including all waste fittings) complete all as specificed and directed

ITEM NO.151 : Brass chromium plated WHB Mixer valve swan neck type for mixing hot and cold water screwed down for 15mm dia iron pipe complete all as specified and directed by Engineer-in-Charge.

ITEM No. 152 Supply & fixing in repairs brass chromium plated WHB Mixer valve swan neck type formixing hot and cold water screwed down for 15mm dia iron pipe compelte all specified and directed by Engr -in- charge.

ITEM NO.153 : Supplying and fixing in repairs 15 mm chromium plated fancy type bib tap brass long body with flange screwed down high pressure CP cast copper alloy with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union complete all as specified and directed by Engineer-in-Charge.

ITEM NO.154 :Supply & fixing Bib tap, cast copper alloy, chromium plated, fancy type,Long body screwed down, high pressure,with crutch or butter fly handle suitable for 15 mm bore pipe or union, complete all as specified and directed by Engineer-in-Charge.

ITEM NO.155 : Supplying and fixing in repairs stainless steel grating openable 100mm size with/without hole including fixing with white cement complete all as specified and directed by Engineer-in-Charge.

ITEM NO.156 : Supplying and fixing in repairs 15mm bore angle cock cast copper alloy chromium plated fancy type screwed down high pressure with crutch or butterfly handle complete all as specified and directed by Engineer-in-Charge.

ITEM NO.157 : Supply & fixed 15mm bore angle cock cast copper alloy chromium plated fancy plate screwed down high pressure with crutch or butterfly handle complete all as specified.

ITEM NO.158: Supplying and fixing stop valves (concealed type),cast copper alloy, fancy type chromium plated screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions,long shank and cup of 15 mm bore complete all as specified and directed by Engineer-in-Charge.

ITEM NO.159 : Supply and fixing in repairs chromium plated stop valve (Concealed type) cast copper alloy screwed down long shank and cup of 15mm bore high pressure with crutch or butterfly handle screwed both ends for iron pipe or unions complete all as specified and directed by Engr-in-Charge .

ITEM NO.160 : Supplying and fixing in repairs 20 mm Brass gated volves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed by Engineer-in-Charge.

ITEM NO.161 : Supplying and fixing fancy type shower rose 125mm dia size of Rim and 30cm long CP brass pipe with swivel joint including fixing to steel pipe or union complete all as specified and directed by Engineer-in-Charge.

ITEM NO.162 Supplying and fixing in repairs Fancy type shower rose125mm dia size of Rim and 30cm long CP brass pipe with swiwel joint in complete all as specified and directed by Engineer in Charge.

ITEM NO.163 : Supplying and fixing Chromium plated hand shower with 1.50 m long flexible tube complete all as specified and directed by Engineer-in-Charge.

ITEM NO.164 : Supply & fixing in repair CP brass wall mixer 3 in 1 system with provision for both hand shower and overhead shower complete with 115mm long bend pipe, connecting legs and wall flange with hand and overhead shower complete all as specified and directed by Engineer-in-Charge.

ITEM NO.165 : Supply & fixing CP brass wall mixer 3 in 1 system with provision for both hand shower and overhead shower complete with 115mm long bend pipe connecting legs and wall flange with hand and overhead shower complete all as specified and directed by Engineer-in-Charge.

ITEM NO.166 : Supplying and fixing 3 tier Corner glass shelf with CP stand complete all as specified and directed by Engineer-in-Charge.

ITEM NO.167 : Supplying and fixing Sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated guard and railing 60 cm long complete all as specified and directed by Engineer-in-Charge.

TEM NO.168 : Supplying and fixing in repairs Sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated guard and railing 60 cm long complete all as specified and directed by Engineer-in-Charge.

ITEM NO.169 : Supply & Fixing in repair chromium plated Soap dish, fixed to plugs with chromium plated brass screws complete all as specified and directed by Engineer-in-Charge.

ITEM NO.170 Supply and fixing chromium plated soap dish , fixed to plugs with chromium plated brass screws complete all as specified and directed by Engr-in-Charge.

ITEM NO.171 : Supply and fixed in repair brass chromium plated, tubular towel rail, 20mm dia, 60cm long between flanges complete all as specified and directed by Engineer-in-Charge.

ITEM NO.172 : Supply and fixed brass chromium plated, tubular towel rail, 20mm dia, 60cm long between flanges complete all as specified and directed by Engineer-in-Charge.

ITEM NO.173 : PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed by Engineer-in-Charge.

ITEM NO.174: PVC connections 15mm size with PTMT nuts of length 450mm fixed in repair complete all as specified and directed by Engineer-in-Charge.

ITEM NO.175 Stainless steel plate rack of standard size 900mmx750mm mm complete and fixing with rawl plug and steel screws of weight not less than 8kg each complete all as specified and directed by Engineer in Charge.

ITEM NO.176 : Supply and fixed in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste pipe incl bedding in cement mortor to dwarf wall or cantilever brackets and connecting union to pipe overall size 915x460mm, bowl size 410x 330x160mm incl all fittings ie chromium plated waste coupling, waste pipe complete all as specified and directed by Engineer-in-Charge.

ITEM NO. 177 : Sink without drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm, waste pipe complete all as specified and directed by Engineer in Charge.

ITEM NO.179 : Supply and fixing in repair PVC cabinet with looking mirror of size 350x450mm complete all as specified and directed by Engineer-in-Charge.

ITEM NO.180 : 75mm bore cast iron bends any radius with oval access door and diminishing pieces or tapers (larger bore measured) complete all as specified and directed by Engineer-in-Charge.

ITEM NO.181 : 75mm bore Cast Iron sand cast soil waste and vent pipe in any length with or without ears with cement joints laid in trenches or in floors complete

ITEM NO.182 : 75mm bore cast iron soil waste and vent pipe in any length with or without ears with cement joints fixed to wall complete all as specified and directed by Engineer-in-Charge.

ITEM NO.183 : 100 mm bore cast iron soil waste and vent pipe in any length with or without ears with cement joints laid in trenches or floor complete all as specified and directed by Engineer-in-Charge.

ITEM NO.184 : 100 mm bore cast iron soil waste and vent pipe in any length with or without ears with cement joints fixed to walls complete all as specified and directed by Engineer-in-Charge.

ITEM NO. 185 : Stack clamps made of 50mm by 5 mm flat iron and 16 mm dia round iron stays, including bolts & nuts and securing ends of stays to wall or roof for 75 mm bore CI Pipe complete all as specified and directed by Engineer in Charge.

ITEM NO. 186 : Stack clamps made of 50mm by 5 mm flat iron and 16 mm dia round iron stays, including bolts & nuts and securing ends of stays to wall or roof for 100 mm bore CI Pipe complete all as specified and directed by Engineer in Charge.

ITEM NO. 187 :Cast iron P or S trap 100 mm bore complete all as specified and directed by Engineer in Charge.

ITEM NO.188 : 100mm bore CI bends (any radius) diminishing pieces or tapers (larger bore mesured) with oval access door complete all as specified and directed by Engineer-in-Charge.

ITEM NO.189 : CI 75 mm bore branch piece single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches with oval access door complete all as specified and directed by Engineer-in-Charge.

ITEM NO.190: CI 100 mm bore branch piece single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches with oval access door complete all as specified and directed by Engineer-in-Charge.

ITEM NO.191 : CI 100mm bore branch piece double (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches with oval access door complete all as specified and directed by Engineer-in-Charge.

ITEM NO.192 : Cast Iron 100mm socket (double collars), complete all as specified and directed by Engineer-in-Charge.

ITEM NO.193 : CI floor traps complete 75 mm bore outlet including jointing to waste pipe fixed in cement concrete type 1:2:4 type B 1 complete all as specified and directed by Engineer-in-Charge. Note : The quoted rate shall include embedding the floor trap in PCC block of size 300 mm x 300 mm x 250 mm block of PCC 1:2:4 type B-1

ITEM NO.194 : Extra over cast iron pipes and fittings if lead joint is provided in lieu of cement joint for 100 mm bore pipe include for hacking out cement joints or burning out lead joints and collecting useful materials and removing them to stores/credit complete all as specified and directed by Engineer-in-Charge.

ITEM NO.195 : Extra over cast iron pipes and fittings if lead joint is provided in lieu of cement joint for 75 mm bore pipe include for hacking out cement joints or burning out lead joints and collecting useful materials and removing them to stores/credit complete all as specified and directed by Engineer-in-Charge.

ITEM NO.196 :Supply and fixing 4.8mm thick sheet glass ordinary quality with aluminum beading, rubber packing in square/rectangular n exc.0.5sqm in each pane complete all as specified and directed by Engineer-in-Charge.

ITEM NO.197 : 110 mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed by Engineer-in-Charge.

ITEM NO.198 : PVC(SWR) bends (any radius), for 110mm bore pipes, with access doors, complete all as specified and directed by Engineer-in-Charge.

ITEM NO.199 : Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc. of tank capacity n exc 500 Ltr complete including disconnecting and refixing after cleaning the tank all as specified and directed by Engineer-in-Charge.

ITEM NO.200 : Salt-glazed stoneware (SGSW) gully traps,150x150 square or round mouthed, type "P" setting and jointing to drains with cement mortar 1:1 complete all as specified and directed by Engineer-in-Charge.

ITEM NO.201 Cast Iron vent cowl 100 mm bore size, complete all as specified and directed by Engineer in Charge.

ITEM NO.202 : Wire brushing and cleaning the top surfaces of tiles, lime terracing or cement concrete, roof surfaces etc. with water including flashings and junction of parapets etc. complete all as specified and directed by Engineer-in-Charge.

ITEM NO.203 : APP polymeric water proofing membrane minimum 3 mm thick and weighting not less than 3.0 Kg/Sqm black finish reinforced with non-woven polyster matt wt not less than 150 gms/Sqm with thermo fusable finish laid over compatible bitumen primer at the rate of 0.40 Ltr/Sqm torching over laps with a propane or abutangas torch with a over lap of 75 mm at the side and 100 mm at the ends and sealing including applying a coat of cold emulsion bituminious primer all as per manufacturers instructions incl preparation of surface complete all as specified and directed. Note :- The water proofing treatment shall be got carried out by the manufactarer or their authorised applictor's duly approved by GE in writing.

ITEM NO.204 : Heat resisting painting to surfaces of any description wood, steel, iron, concrete, brick, stone, APP surface, etc., exceeding 10cm in width or girth incl preparation of APP surfaces complete all as specified and directed by Engr-in-charge

ITEM NO.205 : Rolled mild steel as in roof truss (framed) trussed purlins crane gantries, rails and fastening and heavy bracket framing (beam, tee angle channel or flat section) including distance pieces, cleat etc conforming to Fe-410 W (Gde E-250 ) quality 'A' complete all as specifed and directed by Engineer-in-Charge.

ITEM NO.206 : Rolled Mild steel work as in Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment for covering to steel doors, gates including necessary welding, confirming to Fe-410-W (Gde-E-250) quality-A complete all as specified and directed by Engineer-in-Charge.

ITEM NO.207 : Supply and fixing Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc complete all as specified and as directed by Engr-in-charge.

ITEM NO.208 : Supply and fixing Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc complete all as specified and as directed by Engr-in-charge.

ITEM NO. 209 :Cutting into existing manholes for connecting new drains, making good to pipe and rendering,cutting out existing benching for and forming branch channel(1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished, and reforming benching as required for 150 mm dia pipe complete all as specified and as directed by Engineer in Charge.

ITEM NO. 210 : Material and labour for carrying out water proofing treatment of sunken floor complete all as specified under :-- (i) The concrete / wall surface shall be cleared thoroughly of all laitance,loose particles ,dust,grease etc and any friable and unsound area which shall be chipped,cleaned and thereafter pre-wetted to a saturated surface dried condition (ii) In case of pot holes/superficial cracks,the same shall be repaired with polymer modified mortar using URP as admixture @ 10% of cement content (iii) The polymer modified mortar using URP as admixture @ 10% of cement content shall also be applied on vertical surfaces after removing of plaster upto 60 cm height (iv) The surface thus prepared shall be coated by applying 2 coats of Dr Fixit Hydrochem Super in the sunken areas and extending it upto 150 mm above the finished floor level.This includes layer of a 150 mm wide strip of an open woven glass fiber mesh over the PCC benching (Gole) on the 1st coat while it is still wet (v) Rendering 10 mm in CM 1:4 admixed with integral water proofing compound LW+ @ 200 ml per bag of cement complete all as specified and as directed by the Engineer-in-Charge.

ITEM NO. 211 : Material and labour for Precast Cement concrete Type B1, 1:2:4 using 20 mm graded crushed stone aggregates as in copings, kneelers apex stone, columns, posts, boundary pillars, bonders and cover slabs (for manholes and drains) and like, set in cement mortar 1:4 complete all as specified and directed by the Engineer-in-Charge.

ITEM NO. 212 : Material and labour for Cement concrete (1:5:10), type E-2, using 40 mm graded mechanically crushed stone aggregates as in filling in sunken floor,rounded or chamfered on edges complete all as specified and directed by the Engineer-in-Charge.

ITEM NO. 213 : supply & fixing in repairs Galvanised iron tubes, `medium grade',40 mm bore, with as in spout complete all as specified and directed by the Engineer-in-Charge.

ITEM NO.214 : Cutting holes n. exc 150 Sq. cm into or through brick walls built in cement mortar and making good in cement concrete 1:2:4 type B-1 as required complete all as specified and directed by Engr-in-Charge of depth .

ITEM NO.215 : Material & labour for applying Two or more coats of 100 % Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS-15489:2004, Alkali & fungal resistance, dirt restance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 ltre/10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 Sqm over new surfaces complete as all spfd and directed by EIC

ITEM NO.216 : Complete removal of existing treatment of wall and applying Two or more coats of 100 % Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS-15489:2004, Alkali & fungal resistance, dirt restance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 ltre/10 Sqm over and icluding priming coat of exterior primer applied @ 0.90 litre/10 Sqm over old surfaces complete as all spfd and directed by EIC

ITEM NO 217: Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete all specified and directed by Engr-in-Charge

ITEM NO. 218 :Material & Labour for preparation of new plastered surface and applying two coats or more coats Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete , as per manufacturer's specification. complete as specified and directed.

ITEM NO. 219 : Complete removal of existing treatment of old wall surface and applying Two or more coats Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete , as per manufacturer's specification. complete as specified and directed.

ITEM NO. 220 :Material & Labour for post anti termite treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and directed by the Engr-in-charge.

ITEM NO. 221 : Material & Labour for post anti termite treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed by the Engr-in-charge.

ITEM NO. 222 : Material & Labour for post anti termite treatment of voids in masonry using chemical emulsion one litre per hole, at 300mm intervals including drilling holes at 45 degree and replugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors complete all as specified and directed by the Engr-in-charge.

ITEM NO. 223 : Baroda Green marble, 15-18 mm thick, machine cut, laid over & including bedded and jointed with adhesive suitable for granite/ stone & pointed with grout of matching shade including necessary cutting over & including 15 mm thick (average thickness) cement mortar (1:4) screed, as in tread of Stair case complete , all as specified and directed by Engr- in- Charge.

ITEM NO. 224 : Supply & Fixing 150 mm overall length of cover plate Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all specified and directed by Engr-in-charge.

ITEM NO. 225 : Supply & Fixing CP Water purifier RO Connecting piece for Water Bib Tap for inlet of RO etc complete and directed by Engr-in-charge.

ITEM NO.226 : Supply & Fixing two way bib Tap chromium plated brass fancy type of 15 mm bore complete all as specified and directed by Engr-in-charge.

ITEM NO.227 : Supply & Fixing two way angle valve cock chromium plated brass fancy type 15mm bore complete all as specified and directed by Engr-in-charge.

ITEM NO.228 : Supply & Fixing in repair Towel ring square with round flange complete all as specified and directed.

ITEM NO. 229 : Supply & Fixing Towel ring square with round flange complete all as specified and directed

ITEM NO. 230 : Supply & Fixing for CI Bends (as radius) with duck 's foot or heel rest 75 mm complete all as specified and directed by Engr-in-Charge.

ITEM NO. 231 : Excavation in trenches n. exc 1.5 m wide and n.exc 1.5 m deep as in soft /loose soil for foundation etc or for shaft walls,cesspit, manhole etc n.exc 10 sqm on plan complete and directed by Engr-in-Charge.

ITEM NO. 232 : Returing, filling spreading,levelling and well ramming in layers not exceeding 25 cm in each layer as in soft /loose soil complete and directed by Engr-in-Charge.

ITEM NO. 233 : Removing excavated material and debries obtained from demolistion to a distance exc 250 m but n exc 500 m and depositing where directed at a level n exc 1.50 m above the starting point complete and directed by Engr-in-Charge.

ITEM NO. 234 : Cleaning of sludge from the manholes by taking out loose sediment sand,girt, ash, sludge water, rags,fibres or vegetation from manholes including removal of sludge/ debris to a distance exceeding 250 m but not exceeding 500m and buried under ground complete and directed by Engr-in-Charge.

ITEM NO. 235 : Demolition of cement concrete unreinforced of any description and in any position not otherwise specifically provided for complete and directed by Engr-in-Charge.

ITEM NO. 236 : Removing building materials etc (other than spoil payable under items 03028 to 03031 in section 3- Earthwork) to a distance of 5 KM or under beyond the lead included in the rates including loading, unloading and stacking at the destination complete and directed by Engr-in-Charge.

ITEM NO. 237 : Excavation in post holes each n.exc 0.5 cum getting out returning filling in and ramming earth or broken rubble mixed with earth around in layers not exc 25 cm watering and removing surplus soil to a distance n.exc 50m and making good surface complete and directed by Engr-in-Charge.

ITEM NO. 238: Material & labour for cement concrete 1:3:6 type C-2 (40 mm graded Mechanically crushed aggregate) as in post/strut foundation complete and directed by Engr-in-Charge.

ITEM NO. 239 : Surface dressing not exc 15 cm deep in soft/loose soil complete and directed by Engr-in-Charge.

ITEM NO. 240 : Surface excavation n.exc 30 cm deep and averaging 15 cm deep and getting out in soft loose soil and getting out including cleaning all grass, vegetation saplings, shrubs,bushwood under growth roots and trees complete and all as specified

ITEM NO. 241 : Removing excarated soil 15 Km but n. exc 5 Km and deposited where directed complete and directed by Engr -in-charge.

ITEM NO. 242 : Material and labour for sand filling under floor or in foundation including watering and consolidation complete and directed by Engr -in-charge.

ITEM NO. 243 : Material and labour for 60 mm thick coloured Machine pressed of concrete inter locking paver block any shape and size confirmming to IS-15658 -2006 of 60mm thickness M-35 grade with grey cement and no pigment to match complete all as specified and directed by Engr -in-charge.

ITEM NO. 244 : Material and labour for 80 mm thick coloured Machine pressed precast concrete inter locking paver block any shape and size confirmming to IS-15658 -2006 of 80mm thickness M-40 grade with grey cement and no pigment to match complete all as specified and directed by Engr -in-charge.

ITEM NO. 245 :Dismanling of RCC posts or struts (wood, steel or RCC) in any section in fencing including taking out embedded portions and making good disturbed ground complete all as specified and directed by Engr -in-charge. Note : Post embedded in natural ground.

ITEM NO.246 : All as per item No 245 above but posts embedded in concrete brick masonry etc complete all as specified and directed by Engineer-in-Charge.

ITEM NO. 247 : Taking down existing barbed wire with fencing of any description and removing the unservicable wire from site complete all as specifed and directed by Engr -in-charge.

ITEM NO. 248 : Mild steel work conforming to Fe-290 or Gde E-165 as in Fencing posts and struts including cutting bending top to shape as directed drilling holes matching forbarbed wire, including fillet on backside of fencing post and all necessary drililng work complete all as specified and directed by Engr -in-charge.

ITEM NO. 249 : supply only chain link fencing using 3.15 mm to 4mm dia GI wire 75x75/100x100mm mesh including line wires any mesh, size and type to any type of standards, rails, straining bolts etc including provision of binding wire complete all as specifed and directed by Engr-in-charge.

ITEM NO. 250 :Fixing only chain link fencing inlcluding line wires, any mesh, size and type of standards, straining bolts etc including provision binding wire complete all as specifed and directed by Engr-in-charge.

ITEM NO. 251 : Supply & fixing flat iron of size as directed as in fixing clamps or support to chain link fencing & struts etc fixed with nut and bolts making necessary hole complete all as specified and directed by Engr -in-charge.

ITEM NO. 252 : Mild steel round bars 10mm dia and over, cut to length, bent to shape required including cranking bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips Gde-I IS-432 (Part-I) complete all as specified.

ITEM NO. 253 : Mild steel screw bolts (Machine made) 5 to 10 mm dia of shank with hexagonal or square heads at one end and screwed the other each screw end to be fitted with washers and one hexagonal or Square nut exc 5 cm but n. exc 10 cm long complete and all as specified

ITEM NO. 254 : Demolition of PCC in any position not otherwise specifically provided for as surface channel,drains, manholes copings and removing debries outside MD land complete all as specified and directed by Engr-in-charge

ITEM NO. 255 : Demolition of RCC Manhole cover including RCC stab set in cement mortar complete all as specified and directed by Engr-in-charge

ITEM NO. 256 : Preparing of new steel surfaces and applying two coat of sunthetic enamel paint over a coat of primer (red oxide) surfaces of any description n.exc 10 cm in width or girth complete all as specifed and directed by Engr-in-charge

ITEM NO.257 : Taking down Copper/Aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, lights fittings etc ceiling roses , penendants regulator, sockets light fitting removing material to store for keeping in safe custody for taking credit (credit for above items should be made as per condition seperately) and making good distrubed surface of walls, floors etc complete all as specified and directed by Engineer-in-Charge. Note :-- Rate for cutting /chasing in walls and making good deemed to be included in quoted rate.

ITEM NO.258 : Taking down ceiling fan any size or any type and deposited to concered AGE E/M store yard complete all as specired and directed by Engineer-in-Charge.

ITEM NO.259 : Taking down old exhaust fan any sizeor any typeand deposited to concerned AGE E/M store yard complete all as specified and directed by Engineer-in-Charge.

ITEM NO.260 : Taking down old unserviceable /serviceable single or three phase electric meter and old Meter shall be deposited to concerned AGE E/M store yard complete all as specified and directed by Engineer-in-Charge.

ITEM NO.261 : Taking down old and unserviceable sub main wiring any size / type / core incl earth wire complete with batten/conduit etc and making good the disturbed surface to match the existing disturbed surface complete all as specified and directed by Engineer-in-Charge. Note :-- Rates for cutting/chases in walls and making good disturbed area deemed to be included in the quoted rate

ITEM NO.262 : Taking up old unserviceable earthing of any type complete all as specified and directed by Engineer-in-Charge.

ITEM NO.263 : Taking up old unserviceable cable any type/any size complete all as specified and directed by Engineer-in-Charge.

ITEM NO.264 : Taking down old and unverservicable MCB DB TPN/SPN /metal clad socket and making good the distributed surface specified and directed by Engineer-in-Charge.

ITEM NO.265: Taking down old and unverservicable MCB any size any type all as directed specified and directed.

ITEM NO. 266 Taking down of water heater any type size / capacity with all accessories after removing of old connection and deposited to concerned AGE E/M store yard for repairs complete all as specified and directed by Engr - in- Charge.

ITEM NO.267 :Point wiring using approved colour coding as per IS with stranded copper conductor 1.5 sqmm (Nominal area) , single core, flame retardant low smoke and low halogen (FRLSH) PVC insulated and unsheathed cabel 1100 volts grade ISI 694 marked multistranded copper conductor including rigid PVC concealed conduit ISI marked and its fitting ISI marked PVC junction boxes, mild steel sunken boxes (terminal boxes) with earth dolly, duly painted internally & externally with two coats of anti corrosive paint over a coat of red oxide primer including provision of new modular cover plate over sunken boxes for mountingmodular switch, socket outlet, fan regulator etc, including flameretardant low smoke and low halogen (FRLHS ) PVC insulated unsheathed stranded copper conductor 1.5 sq mm (Nominal area) single core cable as earth dolly complete all as specified for the following :- Note : (i) cutting /chasing of wall etc deemed to be included in the quoted rate of this item. (ii) Switch, socket outlet and fan regulator to be measured and paid for separately

ITEM NO. 267 :(a) one light point controlled by one switch or one (celling/wall/Exhaust) fan point controlled by one switch and regulator.

ITEM NO. 267 :(b) one 3 pin 5 Amps socket outlet on independent board

ITEM NO. 267 :(c) One 3 pin 5 Amps socket outlet on same board with other switches

ITEM NO. 267 :(d) One light point controlled by two, two way switches.

ITEM NO 268 All as per srl item no 267 above but for one socket point 15 Amp with 2.5 Sq mm PVC unsheathed. FRLSH 1100 volt grade ISI marked with multistranded copper conductor alongwith 2.5 Sqmm green colour FRLSH 1100 volt grade ISI marked copper wire as earth continuity conductor connected to common earth dolly complete all as specified and directed by Engineer -in -charge.

ITEM NO .269 All as per srl item no 267 above but for one socket point 15 Amp with 4.00 Sq mm PVC unsheathed. FRLSH 1100 volt grade ISI marked with multistranded copper conductor alongwith 4.0 Sqmm colour FRLSH 1100 volt grade ISI marked copper wire as earth continuity conductor connected to common earth dolly complete all as specified and directed by Engineer -in -charge.

ITEM NO. 270 : Modular Switch one way 16 Amps one module complete all as specified and directed.

ITEM NO. 271: Supply & fixing Modular Switch one way 16 Amps one module complete all as specified and directed.

ITEM NO. 272 : Supply & fixing Modular socket 6 Amps 5 pins one module complete all as specified and directed.

ITEM NO. 273: Supply and fixing Modular Socket 6/16 Amps 6 Pins 2 module complete all as specified and directed.

ITEM NO. 274 :Supply and fixing Modular fan regulator step type 2 module complete all as specified and directed.

ITEM NO. 275 :Supply and fixing Celling rose surface type back 65 x 20 mm size three terminal complete all as specified and directed

ITEM NO. 276 : Supply and fixing Electric AC ding dong bell type 230 volt single pole complete all as specified and directed.

ITEM NO. 277 :Supply and fixing Lamp holder suitable for batten fitting insulated body with back plate complete all as specifed and directed by Engr -in- Charge

ITEM NO. 278 :Supply and fixing Indoor decorative LED tube light fitting box type with opal diffuser , high efficient PVC housing body suiable for and including LED tube high efficient AC - 220-240 Volts 50 HZ and including 18/20 LED tuberod (luminaries) environment friendly TB with aluminum extrusion heat sink connecting with copper conductor flexible cable from rose to connector of light complete all as specified and directed.

ITEM NO. 279 :supply and fixing LED surface mounted bulk head luminaries 8-10 W with min 800 lumen industrial model IP 65, Aluminum housing, surge protection including driver & LED etc complete all accessories connecting with copper conductor flexible cable from ceiling rose to connector of the light incomplete all as specified and directed.

ITEM NO.280 : Supply and fixing Surface mounted wall mirror LED light compact & study 10 Watt LED decorative fixture with anti glare polycarbonate diffuser , multi purpose lighting solution & application. all accessories & fixture , internally prewired and connecting by providing copper flexible wire 23/0076 mm twin core upto fitting complete all as specified and directed.

ITEM NO.281 : Supply and fixing LED light fitting 9/12 watt wall mounting fixture (Sketch type) in wooden housing, including retrofit LED lamp 9 watt compact and engery efficient epoxy powder coated light luminaire including disconnecting and taking down existing unservicable light fittings of any description complete all as specifed and as directed by the Engineer in charge

ITEM NO.282 : Supply and fixing LED Bldg security Light fittings of capacity 20-25 watt made up of die cast aluminum housing with black expoxy powder coating with cover heat resistance glass safety input voltage 170 to 270 Volts with IP-66 protection and other connected accessories including service bracket of MS pipe 25/32mm bore of length 0.9 Mtr including two coat of synthetic enamel paint over a coat of red-oxide fixed with MS clamps, bolts, nuts and washers and suitable reducer for connecting to MS pipe as required at site and making electrical connection complete all as specified and directed.

ITEM NO. 283 : Supply and fixing Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of capacity 20 Amps complete all as specified and directed

ITEM NO.284 : Supply and fixing MCB DB 4 way TPN Double door powder coated complete alongwith 200 Amp , 415 Volts rated bus bar IP 43 protection , suitable for MCB 4 Pole 63 Amp as incommer. complete all as specified and directed Note : Thimble/lugs of rating of MCB TPN should be used with wire for fixing in the MCB .

ITEM NO.285 : Supply and fixing MCB TPN 63 Amps 440 volts 10 KA B Curve complete all as specified and directed.

ITEM NO.286 : Fixing only MCB DB verticle type 4 way TPN, double door . Complete all as specified and directed Note : Thimble/lugs of rating of MCB TPN should be used with wire for fixing in the MCB

ITEM NO. 287 :Supply and fixing Sheet metal MCB DBs 12 way with 200 Amps rated bus bar single pole and neutral with metalic duble door IP-54 fixed on wall grouted in solid block, including copper lugs, thimbles duly crimped for connection complete all as specified and directed.

ITEM NO. 288 :Supply and fixing Sheet metal enclosers MCB DBs 240 volts, 4 way, double door type grouting in wall in cement mortar making good of disturbed surfaces and matching with existing and electric connection complete all as specified and directed.

ITEM NO. 289 : Fixing only MCB DB SPN 8 way double door complete all as specified and directed Note :Thimble / Lugs of rating of MCBTPN should be used with wire for fixing in the MCB.

ITEM NO. 290 :MCB SP 6-40 Amps, 240 Volts 10 KA 'B' Curve including removing old unservicable MCB complete all as specified and dierected.

ITEM NO. 291 :Fixing only MCB SP 6-32 Amps complete all as specified and directed Note : Thimble /lugs of rating of MCB should be used with wire for fixing in the MCB

ITEM NO. 292 :Fixing only MCB SPN 6-40 Amps complete all as specified and directed Note : Thimble lugs of rating of MCB should be used with wire for fixing in the MCB

ITEM NO. 293 :MCB SPN 6-32 Amps, 240 Volts 10 KA 'B' curve complete all as specified and dierected.

ITEM NO. 294 :MCB SPN 40-63 Amps, 240 Volts ,10 KA B Curve complete all as specified and dierected.

ITEM NO.295 : Hanging only ceiling fan after completion of civil work rubbing withsand paper, taking off old paint with the help of chemicals & painting the ceiling fan with one coat of superior quality fan with one coat of superior quality synthetic enamel paint complete all as specified and directed by Engr-in-Charge

ITEM NO.296 : Fixing only exhaust fan after completion of civil work cleaning the exhaust fan, rubbing with sand paper, taking off old paint with the help of chemicals & painting the exhaust fan with one coat of superior quality synthetic enamel paint complete all as specified and directed.

ITEM NO.297 : Supply and fixing Exhaust fan , steel body , AC single Phase 230 V of size 300mm with blades frame and louvers complete and all as directed by Engineer-in-Charge.

ITEM NO.298 : Supply and fix ceiling fans AC , single Phase 230 volt 50 Hz copper wounded of 1200 mm sweep with BLDC technology max power input upto to 35 watt copper wire induction motor with 5 star BEE rating complete including alongwith canopy cover down road U clamp 03 core PVC flexible cable 1 sqmm for making connection of fan and hanging the fan in clamp connecting the existing electrical connection all as specified and as directed by Engr in charge. Note : MES No shall be written by the contractor with parmanent marker over ceiling fan of specified size and colour and quoted rate shall be deemed to be included of this element.

ITEM NO.299 : Refixing of water heater any type and any size/capacity with all assessories such as nut bolt washer steel wire mesh PVC connection heavy duty with brass screw etc with making all connection using three core copper conductor flexible cable drawn through in PVC flexible conduit pipe including painting with two coats of super enamelled paint of existing shade complete all as specified and directed.

ITEM NO.300 : Supply and fix water heater storage type Anti corrosion ABS body, high grade PUF insulation with enamel coated glass line stainless steel inner tank and heating element upto 2KW capicity 25 Ltr, BEE 5 Star rated complete with all accessories such as safety valve, thermostat, NRv, steel wire mesh heavy duty PVC connection etc. Complete all as specified and directed by Engr-in-Charge.

ITEM NO.301: Refixing of servicable electronic energy meter 5 to 60 Amps capacity complete all as specified and directed.

ITEM NO.302 : Supply and laying Sub main wiring with Four run single core 10sqmm PVC insulated , unsheathed cable FRLS-H 1100 volt grade ISI marked with multi stranded copper conductor with one run of 10 sqmm PVC insulated , un sheathed cable FRLS-H 1100 volt grade ISI marked multistranded copper conductor connected to common earth dolly including capping & casing or concealed on wall/ceiling in PVC conduit medium grade not less than 25 mm dia ISI marked of adequate size of housing the wires complete all as specified. Note (i) Thimble/lugs of rating of MCB should be used with wire of fixing in the MCB (ii) Five run of 10 sqmm cable will be measured as one unit.

ITEM NO.303 : Sub main wiring with two single core FRLSH PVC insulated and unsheathed cable with stranded copper conductor of 4 sqmm drawing in & including PVC concelaed conduit ISI marked with all assesoroies on walls and making good of distrubed surface including all conduit fittings clamps, gutties etc and one addition wire of 4.0 Sqmm but green in colour for earth DB and boxes with proper thimbles all as specified and directed. Note : (1) Thimble/lugs of rating of MCB should be used with wire of fixing in the MCB (ii) Three run of 4 Smm cable will be measurewd as one unit.

ITEM NO.304 : supply & fixing PVC conduit 15 mm dia with 1 run of 1.5 sqmm copper wire drawn through including cutting and chasing in wall and accessories such as bend , T socket etc for inverter circuit complete all as specifed and directed.

ITEM NO.305: Supply and fixing heavy duty wall mouting fan 400 mm sweep with corrosion resistant PVC body minimum noise, operation and maintance free design totally enclosed highly efficient heavy duty motor with pressure die cast aluminum rotor mounted on two ball bearings aerody namically contoured blades rigid frame ,1400 RPM PVC blades and testing complete all as specified and as directed by Engineer in Charge.

ITEM NO.306 : Supply and fixing GI tubing light grade with connected fittings laid in trenches/wall/Pole for protection to under ground cable complete all as specified and directed .

ITEM NO.307: Meterial and Labour Protection of cable with one layer of new bricks laid flat butting to each other in such a way that the per length of the bricks is at right angle to the central axis of the cable using old size sub class B bricks complete all as specified and directed.

ITEM NO.308 : Material & labour PCC (1:3:6) type C-1 using 20mm graded mechnically crushed stone aggregate as in coping, road cutting/hard standing width not more than 0.30 m and depth 0.15 including necessary form work etc complete all as specified and directed.

ITEM NO.309 : Supply and fixing LED lamp 9 watt suitable battern holder complete allas specified and directed.

ITEM NO.310 : Supply and fixing MCCB DB 6 Way VTPN double door powder coated complete alongwith 200 Amp & 415 volts rated bus bar IP 54 Proptection , suitable for MCCB 4 pole 125 Amp as incommer. Complete all as specified and directed. Note : Thimble/lugs of rating of MCB TPN should be used with wire for fixing in the mCB.

ITEM NO.311 : Supply and fixing MCCB 4 Pole 415 volts fixed type 125 Amps suitable for VTPN DB with breaking capacity 16 KA complete all as specified and directed.

ITEM NO.312 : Supply and fixing Modular TV socket complete all as specified and directed.

ITEM NO.313 : Supply and fixing PVC conduit 15 mm dia with 1 run of coaxial cable suitable for TV connection copper wire drawn through including cutting and chasing in wall and accessories such a bend, T, Socket etc for cable TV complete as as specified and directed.

ITEM NO.314 : Supply and fixing Submain wiring with two single core FRLSH PVC insulated and unsheathed cable with stranded copper conductor of 2.50 sqmm drawing in & including PVC conduit ISI marked with all accessories on wall and making good of disturbed surfaces including all conduit fitings, clamps gutties etc and one addiitional wire of 2.50 Sqmm but green in colour for earth DBs and boxes with proper thimble complete and all as specified and directed by Engineer-in-Charge. Note (i) Thimblelugs of rating of MCB should be used with wire for fixing in the MCB. (ii) 3 run of 2.50 Sqm cable will be measured one unit.

ITEM NO.315 : Supply and fixing Sub main wiring with two single core FRLSH PVC insulated and unsheathed cable with stranded copper conductor of 6 sqmm drawing in & including PVC concealed conduit ISI marked with all accessories on walls and making goods of disturbed surfaces including all conduit fittings , clamps gutties etc and one addtional wire of 6.00 sqmm but green in colour for earth DBs and boxes with proper thimbles all as specified and directed Note: Thimbles/lugs of rating of MCB should be used with wire for fixing in the MCB (ii) Three run of 6.00 sqmm cable, wall be measured as one unit.

ITEM NO.316 : Supply and fixing Sheet metal enclosure vertical distribution board VTPN (MCCB DB ) 4 way , double door 415 Volts with 200 Amps rated bus bar IP-54 protection with shrouted neutral bus bar and insulated bus bar & earth link, with and including adjustable thermal setting MCCB 4 pole 125 Amps, 25 KA as incomer and MCBs as outgoing complete with making suitable size of MS cabinet 2mm thick duly grouted on the wall (Flush) with opening arrangement including and making connection with suitable size of lugs and making good the disturbed surface matching with existing surface all as specified and directed.

ITEM NO.317 : supply and fixing SPN distribution board 8 way double door IP 43 as per IS 8623 including 200 Amps fully insulated copper bus bar, insulated neutral bar, earth bar, door earthing , reversible doors, PAN assembly for easy installation and also incoming and outgoing connections with suitable size of lugs/thimbles complete all as specified and directed.

ITEM NO.318 : Supply and fixing MCB SP 240 Volts, 50 HZ breaking capacity 40-63 Amps, ISI marked complete all as specified and directed.

ITEM NO.319 : Supply and fixing MCCB 160 Amps 4 Pole 36 KA 415 volts, 50 Hz complete all as specified and directed .

ITEM NO.320 : Earthing complete with and including galvanised steel earth plate electrode 600 mm x 600 mm x 6 mm surrounded by a mixture of charcoal and salt in alternate layers burried directly in ground vertically in a pit of depth not less than 2.25 m deep below ground level with top edge of earth plate at a depth of not less than 1.5 m below ground level, connected with and including galvanised iron or steel earth wire, 4mm dia (No. 8 SWG) by means bolts, nuts, check nuts and washers made out of galvanised iron, 15 mm bore (medium grade) GI pipe for protection of earthing lead, 20 mm bore (light grade) GI pipe for watering with funnel, wire mesh and including necessary excavation and earth work, PCC 1:2:4 type B-1 pit and 50 mm thick RCC M-25(Design mix) reinforced with XPM (weight not less than 3 kg/sq m) pit cover, C.I frame, charcoal and comman salt filling in alternate layers, complete specified in electrical plate No. 3 of SSR Part-I (2009) and directed by Engineer-in-Charge. Note : The unit rate includes for protecton pipe 15mm and GI earth wire 4mm dia from top of earth plate upto 7.50 metre above ground level.

ITEM NO.321 : Supply and fixing XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric cables (1100 volt) cross sectional area 50 sqmm, 3.5 core,stranded aluminium conductor including cable glands, cable lugs etc , to suit the cable size, 1100 volts grade, ISI marked, laid in trenches or fixing along the poles or passing through the pipes or laid under floors or through walls/ducts etc. complete and all asdirected by Engineer-in-charge.

ITEM NO.322: Supply and fixing XLPE insulated, screened, PVC bedded, galvanised steel strip wire armoured electric cable (1100 volts) cross sectional area 16 sqmm, 2core stranded aluminium conductor including cable glands, cable lugs etc , to suit the cable size, laid in trenches or fixing along the poles or passing through the pipes or laid under floors or through walls/ducts etc. complete and all as directed by Enginer-in-Charge.

ITEM NO.323 : Excavation/cutting the existing hard standing /PCC /WBM road at a depth not less than 45 cm and 30 cm in width for passing of cable through GI pipe, returning filling & removal spoil materials making good existing surfaces complete and directed by Engr-in-charge

ITEM NO.324 : Clean dry sand laid in frenches /duts for bedding and to cable 8 cm in depth before laying the cable and 15 cm often laying the cable including spreading levelling and consolidation complete all as specified and directed . Note : consolidated /panned sand shall be measured for payment purpose.

ITEM NO.325 : Supply and Fixing modular telephone socket RJ 11 with MS suken boxes including suitable cover plate complete all as specified and directed by the Engineer-in-Charge

ITEM NO.326 : Supply and fixing PVC conduit 15mm dia including accessories such as bend, T socket etc with 1 run of RJ 11 telephone landline cord cable suitable for landline including cuttting and chasing in wall and mariking good surfaces complete all as specified and directed by the Engineer-in-Charge

ITEM NO.327 : Supply and fixing stainless steel electric kitchen chimeny 60cm with 1000 cum/hr suction intelligent auto clean, covered glass baffle filter, re volutionary motionsensor control ss oil collector tray with in built LED light including aluminium flexible pipe of diameter 150mm 8.5 feet long (after expansion) with all accessones including making cutting hole of 150mm dia suitable for aluminium exhaust pipe and making good surfaces complete all as specified and directed.

ITEM NO.328 :Supply and fixing modular bell push 6 Amp, 1 way, 1 module, 230 volts complete all as specified and directed by the Engineer-in-Charge

ITEM NO.329 :Supply and fixing modular switch 6 Amp, 2 way, 1 module, 230 volts complete all as specified and directed by the Engineer-in-Charge

Note: For the purpose of arriving at lumpsum amount, the amount of credit schedule i.e Sch 'A' (i.e Rs 1606190.25 shall be deducted from the total amount arrived.

JYOTI ENTERPRISES

Phoenix Infra

Shree Construction Co.

Kartik Builders

Standard Const. Co.

M/S RAJINDER SINGH

SOM BUILDERS