PROVN OF 02 BATHROOMS AND GUARD ROOM AT LT AD BTY, 06 TOILETS NEAR RATION STORE FOR SIKH LI AT KAKSAR, ONE SENTRY POST CUM GUARD ROOM WITH ATT TOILET AND BATROOM AT ORD DET UNDER GE KARGIL

Amount

Excavation in trenches n.exc 1.5m wide and getting out in hard/dense soil

Surface dressing n exc 15 cm deep and getting out in Sqm hard/dense soil

M&L for cement concrete type D-2 1:4:8 (Using 40mm graded aggregate as in fdn

Returning filling in including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick

Removal of surplus soil to a distance exceeding 50 mtr and depositing where directed at a level not exceeding and depositing where directed at a level not exceeding 1.5m above the starting point

M&L precast cement concrete 1:3:6 type C-1 block masonary with solid block exc 10cm in width and setting in cement mortar 1:4

Hard core of broken stones or boulders of gauge in exc 63mm deposited spread and levelled in layers n. exc 15cm thick incl watering and rolled to true surface.

M&L cement concrete type C-1, 1:3:6 (20mm graded aggregate) 50mm thick as in plinth protection finished even ad smooth w/o using extra cement

M&L 75mm thick cement concrete (1:4:8) type D2 as sub base to floor as specified.

M & L for screed or bedding layer 15mm thick in cement mortar 1:6 finished even and fair on floors for laying floor finishes.

S & F non skid ceramic tiles coloured , 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.06Sqm but not exceeding 0.11 sqm, in floor etc, set and jointed in neat cement sturry and pointed in white cement with pigment to match all as specified.

M&L for Vitrified coloured ceramic tiles 10mm thick (squar / rectangular) area of each tile n. exceeding 0.36 sqm in floors etc set and jointed in neat cement slurry and jointed in white/coloured cement to match over and including 15 mm thick backing coat in cement mortar in (1:6), complete all as specified and as directed by Engr-in-charge.

M & L for rendering 15mm thick on verticle surfaces in CM 1:4 finished even and fair all as specified and as directed.

M & L for rendering 10mm thick on brick/concrete surfaces in CM 1:6 finished even and fair all as specified and as directed.

S & F glazed ceramic tiles colured of size 300m x 200mm x 7mm thick on vertical surfaces such as dados, skirting etc, set and jointed inn neat cement slurry and pointed in white cement with pigment to match all as specified.

S&F 9 mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with nails to timber rame work complete, all as specified and directed by Engr-in-Charge

M&L 2nd class soft Wood as in plain fillets square, clean sawn exc. 13 sqcm but n.exc 25 sqcm in section, fixed with nails complete all as specified and directed.

Moulding as in cornices picture rails and the like n exc 6sqcm complete all as specified and directed by Engr-in-Charge.

M&L second class wood designer Plain fillets square,rectangular or triangular in section, Exc 3Sqcm byt n.exc 6Sqcm, clean sawn, secured with nails or brads complete all as specified and directed by Engr-in-Charge.

M&L for Granite(of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing types including15mm thick screed bed as in 1:6 and including dismantling of stone slab complete all as specified

M&L preparation of new plastered surfces of walls and applying two coat of OBD over a coat of birla wall care putty for smoothness of surfaces.

Prepation of new steel surfaces and applying two coats of synthetic enamel paint over a coat of redoxide primer

Prepation of new plastered or unplastered surfaces of walls and applying two coats of Cement base paint , complete all as specified and directed by Engr-in-Charge.

M & L preparation of wood or wood based surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer.

S&F 35 mm thick second class soft wood Glazed and skeleton shutters, open rebated and prepared to raceive glass, gauze, etc., divided in to squares with plain, chamfered or rounded mitred and rebated sash bars any numbers, edges of framing plain, chamfered.

Second class soft wood (KAIL) plain, framed, panelled shutters (any number of panels), 35 mm thick with panels of 9mm ply BWP commercial type or 12 mm thich of veneered particle board with commercial veneering both faces as in doors, complete all as specified and directed by Engr-in-Charge.

S & F butt hinges medium weight cold rolled mild steel of 100mm long

S & F butt hinges medium weight cold rolled mild steel of 75 mm long.

S & F aluminium alloy, anodised sliding door bolt with hasp staple ( bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed 300mm long.

S&F Aluminum Anodised barrel tower bolts of extruded section, 150mm long.

S & F 100 mm long Aluminium, anodised, barrel tower bolts of extruded section

S & F anodised aluminium handle, cast type anodised section 150mm size.

S & F mild steel pressed handle oval type stove enamelled black of 100 mm long.

S&F pre-painted galvalume aluminium zink coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screw as specified

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to walls,fixed with J type hook, complete all as specified and directed by Engr-in-Charge.

Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0

Second class soft wood (KAIL), plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed by Engr-in-Charge.

Second class soft wood (KAIL), clean sawn timber scantling as in purlins ,rafters etc, complete all as specified and directed by Engr-in-Charge.

S & F in repairs Vitreous china wash basin, white, flat back, size 550X400 mm including waste pipe, bracket and cutting for and pinning in ends of brackets or errecting stand but excluding taps, chain and plug, complete all as specified and directed by Engr-in-Charge.

S & F in repairs stainless steel squatting pan of pattern “long pan”, size 580 x 440 mm standard ivory with ‘P’ or ‘S” trap, front or back inlet and foot rests, any pattern (excluding flushing cistern and flush pipe).

S&Fin repir PVC low level flushing cistern 10 Ltr capacity with & including brackets for fixing to walls complete and PVC flush pipe of LDPE pipe of pressure rating 6 kg (f)/ sq.cm , all as specified and as directed , fixed in repairs.

S & F tubes medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floors of 15mm dia

S & F tubes medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floors of 20mm dia

S & F 20mm dia gun metal gate valve with iron wheel head screwed both ends for iron pipe and fixed.

S & F rotational moulded polyethylene water storate tank 1000 ltr capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I

S&F fancy type bib taps 15mm bore, cast copper alloy with crutch or butter fly handle, screwed down, screwed for iron pipe and fixed chromium plated

S&F fancy type pillar taps, cast copper alloy, with capstan head chromium plated 15mm bore

S&F fancy type stop cock 15mm bore chromium plated

S&F towel rail 600mm long of PTMT fixed with and including chromium pated brass screws

S&F grating doom 125mm dia with or without hole

S&F PVC connection 15mm size with PTMT nuts of length 600mm

M&L for Mild Steel deformed or twisted bars or TMT bar, 8 mm dia and above, cut to length bent to required shape incl cranking, bending and binding with Mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed

Mild steel TMT 6 mm to 8 mm dia., cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips qualit

Form work to sides of conrete foundation footings bases of columns, raft and raft beams sides and soffits of foundation and plinth beams and similar work etc. complete all as specified and directed by Engr-in-Charge.

Form work to sides of pillers posts struts piers coloums and stanchions etc.complete all as specified and directed by Engr-in-Charge.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc

M&L for reinforcement cement concrete (nominal mix) type B1 (1:2:4) (using 20mm graded crushed stone aggregate) in foundation , including rafts, footing,foundation beams, plinth beams, bases for coloums etc.complete all as specified and directed by Engr-in-Charge.

M&L for reinforcement cement concrete (nominal mix) type B1 (1:2:4) (using 20mm graded crushed stone aggregate) in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed by Engr-in-Charge.

M&L for reinforcement cement concrete (nominal mix) type B1, (1:2:4) (using 20mm graded crushed stone aggregate) as in columns, pillars, piers, posts and struts, complete all as specified and directed by Engr-in-Charge.

S&F sheet glass 3.00 mm thick ordinary quality, and glazing with oil putty in square nexc. 0.50 Sqm each pane all as specified & directed.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire & average width of aperture 1.40mm with stainless steel wire staples

S&F 110mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floor

S&F 75mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floor

S&F 75 mm Bore PVC (SWR) floor trap, plain with grating including jointing with solvent cement

S&F PVC (SWR) vent cowl 75mm bore

S&F PVC (SWR) bend 110mm bore

S&F PVC waste pipe 32mm dia

M&L for sockage well exc in hard dence soil, foundation in PCC 1:3:6 well of honey combed and each solid in M-25 concrete, including, intercepting chaber, creen chamber stone work in CM 1:4 RCC cover slab in M-25 filling with stone boulder complet of 3.00 dia and 3.00 m deep, complete all as specified and directed by Engr-in-Charge. (Drg No CESZ/TD/-1078/2011 Sheet 1/1)

Point wiring with multi-stranded copper conductor PVC insulated and unsheathed cable in PVC casing and capping, 1.5 Sqmm with all fittings/accessories and including 1.5 Sqmm PVC insulated copper earth wire connected to common earth including closed recessed wooden terminal Boxes of suitable size made of 2nd class hard wood for mounting switches, sockets etc with 3mm thick laminated sheet cover for one light point or bell/buzzer point controlled by one switch, complete.

All as per Srl item No 71 here in before but for one 3 pin 5 Amps switch socket on same board.

All as per Srl item No 71 here in before but for one 3 pin socket outlet 5 Amps on independent board.

Description all as per item No 72 here-in-before but using 4 Sq mm single core copper conductor cable of multistranded PVC insulated unsheathed 1100 Volts grade for industrial plug socket. point including running of 2.5 Sq mm copper conductor PVC wire as earth continuity conductor along with wiring and connecting to the common earth dolly.

Switch piano flush type 5 Amps, single pole one way.

Switch socket combination 2 in 1, and 3 and 2 pin, 5 Amps flush type.

Switch socket combination 2 in 1, 5 and 15 Amps flush type.

Lamp holder, insulated body with back plate suitable for batten fittings

Ceiling rose surface bakelite 65x50mm, two to three terminals.

Sheet metal enclosure for DB's Single door, single pole and neutral, 240V, 8 way with 200 Amp rated bus bar including blanking plates where required. Complete all as specified and directed.

MCB, single pole and neutral, 63 Amp, 240V, 10KA.

MCB, single pole, 5 to 32 Amp, 240V, 10KA.

Rectangular block of PVC of size 30 x 25 x 5 cm depth, closed recessed.

Earthing complete with galvanised steel earth plate electrode 600mm x 600mm and 6mm thick buried directly in ground not less than 2.25 mtr deep below normal ground level with top edge of plate not less than 1.5 metres below normal ground level, connected to the Galvanized iron earth wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanized iron protected by provision of G I light grade pipe 40mm bore including provision of concrete pit in PCC 1:2:4 type B1 using 20mm grade stone aggregate with 40mm thick cover of RCC 1:2:4 reinforced with XPM (weight not less than 4Kg/Sqm) and frame of angle iron 25x25x6mm with lugs two number and with 6mm dia MS bar handle made to shape and GI medium grade 20mm bore pipe for watering perforated at bottom 1.75m long placed on top edge of earth plate, common salt and charcoal filling, test point made out of 40mmx8mm flat iron with fixing arrangement funnel wire mesh and earth work in hard/dense soil, returing filling in and removal of surplus soil to a distance not exceeding 50M all as per electric plate No 5 of SSR Part-I conected to earth test point as specified or indicated including testing on completion.

Sub main wiring with two single core 6 sqmm multistranded copper conductor cable, PVC insulated cable 1100 volts grade and 4 Sqmm as continous earthing drawing and including PVC casing and caping of suitable size with all acessories, complete all as specified.

1100 volts grade heavy duty 6 sqmm 2 core flat cable PVC insulated aluminium stranded conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 01 metre apart including 4 mm suspension complete all as specified.

Supply and fixing LED 18 Watt Tubelight fitting decorative ultra slim square profile linear with extruded polycarbonate environment friendly Make Havells Cat part LUMILINEPLUSBS18WLED865SPCSS OR equivalent in WIPRO/PHILIPS

S&F 1100 volts grade heavy duty 35 sqmm 2 core flat cable PVC insulated aluminium stranded conductor, complete all as specified.

S&F 1100 volts grade heavy duty 35 sqmm 3.5 core flat cable PVC insulated aluminium stranded conductor, complete all as specified.

Supply and fixing LED 18 Watt Tubelight fitting decorative ultra slim square profile linear with extruded polycarbonate environment friendly Make Havells Cat part LUMILINEPLUSBS18WLED865SPCSS OR equivalent in WIPRO/PHILIPS

Supply & fix LED building security light 60 watt energy efficient with bracket,suitable dia pipe for fixing the street light in wall all as directed.Make Havells Cat part No.ENDURAPERLINEOSL60WLED75PASYTOPC or equivalent in PHILIPS/WIPRO

Supply and fix Exhaust fan with grills metallic without regulator of sweep 300 mm single phase 250 volts AC supply heavy duty including all fixing material and arrangements, provision of 2 way PVC connector, copper bunched flexible cable 23/0.0076 twin twisted PVC insulated cable from ceiling rose/connector to fan all as specified and directed.

Supply and fix Wall fan with grills metallic without regulator of sweep 450 mm single phase 250 volts AC supply heavy duty including all fixing material and arrangements, provision of 2 way PVC connector, copper bunched flexible cable 23/0.0076 twin twisted PVC insulated cable from ceiling rose/connector to fan all as specified and directed.

Note : Deduction for amount of Rs 0.00 as listed in Schedule A Part - II ( Schedule of Credit) shall be made while awarding of contract.

M/S M A ENTERPRISE

M/S UNIVERSAL ENGINEERS

M/S MOHD HUSSAIN