SPL REPAIR TO ROOF TREATMENT AND KITCHEN OF BLDG NO P-4 (OFFR MESS) AND PROVN OF TOILET AND BATHROOM BLOCK IN FRONT OF WET CANTEEN OF CERTAIN UNIT AT MIL STN KOTA

Amount

Demolition/Dismantling of existing roof treatment, any type from RCC roof slab including lime concrete/PCC padding over roof, removing layer of bitumen under lime concrete/PCC padding, cement mortar, felt etc and cleaning the surface by hacking to receive plaster and removing demolished materials outside MD land, complete all as specified and directed.

Taking down cement plaster of any description and thickness on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

Taking down chowkhat or frames not exc 1.50 Sqm each with shutters (with out taking off shutters from the frame), complete all as specified and directed.

Taking down chowkhat or frames exc 1.50 Sqm and not exc 4.00 Sqm each with shutters (with out taking off shutters from the frame), complete all as specified and directed.

Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically provided for and removing rubbish from premises, complete all as specified and directed.

Demolition of cement concrete (reinforced) as in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work for and removing rubbish from premises, complete all as specified and directed.

Dismantling floor, hearth or wall tiling/ terrazzo including cement mortar bedding (but not backing), removing tiles and rubbish off the premises, complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry built in cement mortar including all quoins, arches, pillars etc. but excluding ashlars facing, dressed stone work & precast concrete articles, complete all as specified and directed.

M&L brick work with old size pulverized fuel Ash-lime bricks (Fly ash bricks - non modular size), straight or curved on plan exc 6 m mean radius, built in CM 1:6, complete all as specified and directed.

M&L for brick work with pulverised fuel Ash-lime bricks (Fly ash bricks - non modular size), straight or curved on plan to any radius in half brick walls built in cement mortar 1:4, complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 (using 40mm graded stone aggreate), 75 mm thick as in plinth protection/Path/PCC paving etc including finishing the surface even & smooth without using extra cement, with and including all necessary form work to divide the area in panels, finishing exposed edges fair or rounding or chamfering where dirtected and providing 6 mm wide joints throughout the thickness of plinth protection duly filled with mastic filling (one part of hot bitumen 85/25 and three parts of fine sand by weight), complete all as specified & directed.

M&L for providing cement concrete 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.

M&L for PCC 1:5:10 type E-2, using 40 mm graded crushed stone aggregate, as in foundation, filling, mass concreting etc, complete all as specified and directed.

M&L for RCC design mix grade M-25 (using 20 mm graded crushed stone aggregate) as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns etc, under-reamed piles and mass concrete, complete all as specified and directed. Note for RCC items :- Reinforcement and formwork shall be measured and paid for separately under respective items of the BOQ.

M&L for RCC design mix grade M-25 (using 20 mm graded crushed stone aggregate) as in columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for RCC design mix grade M-25 (using 20 mm graded crushed stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M&L for RCC design mix grade M-25 (using 20 mm graded crushed stone aggregate) as in chajjas & the like etc complete all as specified and directed.

M&L for RCC design mix grade M-25 (using 20 mm graded crushed stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Form work (rough finished surfaces) to sides of concrete foundations, column footings, bases of columns, raft and raft beams, sides and soffits of plinth beams or other similar works, vertical or to batter for rough finished surfaces, complete all as specified and directed.

Form work (rough finished surfaces) to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc., complete all as specified and directed.

Form work (fair finished surfaces) to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed.

Form work (fair finished surfaces) to chullah hoods, chajjas, troughs and similar items including edge complete all as specified and directed.

Form work (fair finished surfaces) to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

Formwork (rough finished surfaces) to edges of concrete flats, treads, breaks in floors, window cills, concrete rail ings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizon tal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed.

M&L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, slabs, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality confirming to TMT bars complete all as specified and directed.

M&L TMT bars, 6 to 8 mm dia, cut to length, bent to shape required including cranking, bending spirally for hooping for column, hooking ends and binding with and incl MS wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L for PCC 1:2:4 mix type B-0 (using 12.5 mm graded crushed stone agg) for roof padding, leveling course to receive floor finishes etc, complete all as specified and directed.

M&L brushing neat cement slurry with 3.00 kg cement per Sqm, complete all as specified and directed.

M&L for applying 20 mm thick screed in CM 1:3 on roof slabs with using liquid water proofing compound as per manufacturer's instructions, complete all as specified and directed. (Liquid WPC shall be measured and paid separately).

M&L for cleaning of roof slab including picking, sweeping clean and washing down with water to remove dust, dirt etc and Supply and fix APP polymeric water proofing membrane, minimum 3mm thick and weighing not less than 3.0 Kg/Sqm, black finish reinforced with non-woven polyester matt, with a thermo fusable finish laid over cold applied bituminous primer conforming to IS 3384 @ of 0.40 Kg/Sqm torching overlaps with a propane or a butane gas torch, with a overlap of 75mm at the sides and 100mm at the ends and sealing including applying a coat of cold emulsion bituminous primer all as per manufacturer’s instructions, complete all as specified and directed. Note: (i) Coved fillets in PCC(1:2:4) type B-0 using 12.5mm graded stone aggregate, of radius 75mm shall be provided at the junction of roof and parapet wall/mumty/chimney/other vertical surfaces and thereafter surface painted with hot paving bitumen of Grade 30/40 confirming to IS-73, [email protected] Kg/Sqm over a coat of cold applied bituminous primer conforming to IS:3384 @ 0.40 Kg/Sqm.

Item 30.00 Contd........ (ii) Polymeric membrane shall be taken to a height of 45cm (minimum) and then inserted inside the groove of parapet wall of brick masonry and shall be finished by a membrane flushing. (iii) The waterproofing treatment shall be got carried out by the manufacturer or their authorized applicators. (iv) In case of stone masonry parapet wall etc a groove of size 25mmx25mm (minimum) shall be made in coved fillet at the junction of roof and parapet wall/mumty Chimney/other vertical surfaces and polymeric membrane inserted in groove and sealed with paving bitumen. (v) Cost of above aspects is deemed to be included in quoted rates.

Supply only approved liquid water proofing compound, complete all as specified and directed.

S&F 35mm thick factory made IInd Class Hard wood (Hollock) paneled door shutters single panel with lock rail and panel of 9mm B.W.P. marine grade plywood bonded with high quality liquid phenol formaldehyde synthetic resin adhesive conforming to IS-710 or 12mm thick particle board veneered with commercial veneering on both faces. The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed.

S&F 35mm thick factory made IInd Class Hard wood (Hollock) glazed and skeleton, open rebated, prepared to receive glass, gauge etc, without sash bars, edges of framing plain, chamfered and rounded, fitted with cut and mitered beads for securing glass/gauge etc. The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed. Note :- S & F glass/gauge shall be measured and paid for separately.

S&F in renewal of 17/19 mm thick modular membrane kitchen cabinet door shutters (made out of HDHMR boards) in wood grain colour and half round edges, complete all as specified and directed.

S&F 16-18 mm wide & 1mm thick PVC edge banding pasted to edges of PVC furniture with suitable adhesive, complete all as directed.

S & F in renewal of kitchen basket stainless steel of size 435mmx510mm & including SS guide channel of suitable size etc, complete all as specified and directed.

S & F in renewal of perforated cutlary of size 475x485x350mm stainless steel of grade 304, complete all as specified and directed.

S & F in renewal of soft close telescopic drawer channel for fixing of baskets complete all as directed.

S & F in renewal of three tier trolley bottle pull out, bottle size 485 x 530 x 150mm of stainless steel of grade 304 complete all as directed.

S & F in renewal of plate basket of size 475x535x200mm of stainless steel of grade 304, complete all as specified and directed.

S & F in renewal of MP basket of size 475x485x350mm of stainless steel of grade 304, complete all as specified and directed.

S & F in renewal of C & S basket of size 475 x 485 x 350mm of stainless steel of grade 304 complete all as directed.

S & F in renewal of VEG basket of size 475 x 485 x 350mm of stainless steel of grade 304 complete all as directed.

S & F in renewal of Thal basket of size 475 x 485 x 350mm of stainless steel of grade 304 complete all as directed.

S & F in renewal of Grain basket of size 475 x 485 x 350mm of stainless steel of grade 304 complete all as directed.

S & F auto closing hinges, three dimentional adjustment with suitable mounting plate made of stainless steel with nickel plated for corrosion resistance for cupboard and cabinet shutters of kitchen, complete all as specified and directed.

S & F continuous piano hinges, mild steel, bright finish or electro galvanised, 30 mm width of flaps when open, complete all as specified and directed.

S&F magnetic ball catches with 8mm dia steel ball and brass body and striking plate of 50mm size including letting in and fixed, complete all as specified and directed.

S&F of floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in floor, overall length of cover plate 150 mm, complete all as specified and directed.

S&F aluminium anodised barrel tower bolt of extruded section 150 mm long and fixed, complete all as specified and directed.

S&F aluminium handles, cast type, anodised 150 mm size, complete all as specified and directed.

S&F extruded brass handles, fabricated type polished 100 mm size, complete all as specified and directed.

S&F 100 mm size mild steel butt hinges, ISI marked, medium weight, cold rolled and fixed with screws, complete all as specified and directed.

S&F 75 mm size stainless steel butt hinges, ISI marked, B-11 type and fixed with screws, complete all as specified and directed.

S&F 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and directed.

S&F 300 mm long mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete all as specified and directed.

S&F 300 mm long mild steel ordinary rat tail rod pattern springs including roller and roller plate, welded to mild steel frame complete all as specified and directed.

S&F in renewal of towel ring, chromium plated, 200 mm dia, fixed to PVC rawl plugs with CP MS screws, complete all as specified and directed.

S&F 'D' type tubular towel rail 60 cm long, brass chromium plated, 20 mm dia, complete fixed with stainless steel screws, complete all as specified and directed.

S&F Powder coated (thickness of powder coating minimum 50 micron) anodised aluminium frame for doors, windows, ventilators & partition etc., with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F Powder coated (thickness of powder coating minimum 50 micron) anodised aluminium window and ventilator shutters, side hung without sash bars, aluminium sections weighing not less than 0.55 kg/m & including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No), hinges type B-21 100mm long (2 No.), suitable handle (1 No), complete all as specified and directed. Note :- Wire cloth & Glass pane shall be measured and paid for separately.

Supply, fabricated & fixing Powder coated (thickness of powder coating minimum 60 micron) anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer in-charge.

Supply only 5.5mm thick sheet glass ordinary quality, cut to size as required at site, complete all as specified and directed. (Cost of fixing of glass shall be deemed included in the unit rates under respective items.)

Supply only stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm fixed with aluminium wire staples, complete all as specified and directed. (Note: cost of fixing of wire cloth shall be deemed included in the unit rates under respective items.)

S & F for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing as applicable to item 08095 given in SSR Part – II (2020).

S & F for Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails mild steel frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppy and fixing in the frame at site complete all as per specifications and drawings as applicable to item 08080 given in SSR Part–II.

S&F steel windows or ventilators, fixed type with glazing bars including one shop coat of zinc chromate primer complete all as specified and directed.

M&L for figured glass, 4 mm thick, pin head type and glazing with oil putty in squares not exc. 0.50 Sqm in each pane complete all as specified and directed.

S & F of framed work as in doors or gates of angles or other section with gusset plates, rails, braces etc complete drilled for fixing of steel sheeting or other covering doors etc to be prepared for hanging or sliding with including either hooks and hinges or steel hanging door fittings (excluding of steel sheeting or other covering running rails and guides) and hanging also fastening and fixing, conforming to Fe-290 Grade-E-165, complete all as specified and directed.

M&L 100 mm thick PCC 1:2:4 type B-2, using 40 mm graded crushed stone aggregate, as in sub base of floors, etc., finished surface even & fair to receive floor finishes/ screed complete all as specified and directed.

M&L 75 mm thick PCC 1:3:6 type C-2, using 40 mm graded crushed stone aggregate, as in sub base of floors, etc., finished surface even & fair to receive floor finishes/ screed complete all as specified and directed.

M&L for 25mm thick plain cement concrete 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in flooring /sub base finished surface even & fair to receive floor finishes/ screed complete all as specified and directed.

M&L for joint free non skid ceramic coloured tiles, 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for joint free non skid ceramic coloured tiles, 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for joint free non skid ceramic coloured tiles, 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm fixed on vertical surfaces, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 10 mm thick rendering in CM 1:4 backing, complete all as specified and directed.

M&L Glazed ceramic coloured tiles on vertical surfaces 350x 250x7 mm/450X350X7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match, laid over and including 10 mm thick rendering in CM 1:4 backing, complete all as specified and directed.

M&L black granite (of any type) slab 18-20 mm thick, table rubbed and mirror polished by applying wax polish as in cooking platform, jambs, cills, pillars, tread, risers, platform for WHB etc including bull nosing to exposed outer edges, set in CM 1:4 bedding and pointing with white cement mixed with pigment and provn of hole for gas pipe, laid over and including 20 mm thick screed bed in CM 1:6, complete all as specified and directed. Note :- Granite stone slab shall be laid in single piece with rounding of edges and a grove shall be provided beneath the projection portions of slab.

M&L for rendering 15 mm thick on stone masonry surfaces or other than fair faces of brick work in cement mortar 1:4 with using liquid water proofing compound, surface finished even and smooth without using extra cement, complete all as specified and directed. (Liquid WPC shall be measured and paid separately).

M&L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6, surface finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6, surface finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 15 mm thick on stone masonry surfaces or other than fair faces of brick work in cement mortar 1:6, surface finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 15 mm thick on stone masonry surfaces or other than fair faces of brick work in cement mortar 1:4, surface finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 5 mm thick on fair faces of ceiling in cement mortar 1:4 including finishing the surface even and smooth, complete all as specified and directed.

M&L for rendering 10 mm thick on fair faces of ceiling in cement mortar 1:4 including finishing the surface even and smooth, complete all as specified and directed.

M&L for preparing new steel surfaces exceeding 10cm width or girth and applying two coats of synthetic enamel paint over & including one coat of red oxide zinc chrome primer, complete all as specified and directed.

M&L applying 2 coats of synthetic enamel paint over and including a coat of pink primer on wooden surfaces, exceeding 10 cm in width or girth, incl preparation of the new surfaces complete all as specified and directed.

M&L preparation of newly plastered surfaces of walls and applying 1 mm thick wall care putty as per manufacturer's instructions and over it applying two coats of distemper oil emulsion over a coat of suitable primer, complete all as specified and directed.

M&L for complete removal of existing treatment from previously treated plastered/unplastered surfaces of walls and applying 2 mm thick wall care putty as per manufacturer's instructions and over it applying two coats of distemper oil emulsion over a coat of suitable primer, complete all as specified and directed.

M&L preparation of newly plastered surfaces of walls and applying 2 mm thick wall care putty as per manufacturer's instructions and over it applying two coats Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) over new surfaces on walls complete all as specified and directed.

M&L complete removal of existing treatment from previously treated plastered surfaces of walls and applying 1 mm thick wall care putty as per manufacturer's instructions and over it applying two coats Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) over surfaces on walls complete all as specified and directed.

M&L for applying three coats of white wash on ceiling including preparation of new or previously untreated surfaces, complete all as specified and directed.

M&L for applying three coats of white wash on walls including preparation of new or previously untreated surfaces, complete all as specified and directed.

M&L for applying one coat of white wash after preparation of old previously treated plastered surfaces of ceiling, complete all as specified and directed.

S&F HDPE PVC connection 450 mm long suitable for 15 mm GI pipe with two PTMT nuts and rubber washers complete all as specified and directed.

S&F in renewal of HDPE PVC connection 450 mm long suitable for 15 mm GI pipe with two PTMT nuts and rubber washers complete all as specified and directed.

S & F in renewal of superior quality PVC waste pipe, 32/40 mm bore with union, complete all as specified and directed.

S&F in renewal of vitreous china counter wash hand basin white on granite slab, with flat back of size 550x400 mm, fitted with granite stone slab excluding chain and plug, taps and porcelain stopper but incl PVC waste pipe of 32 mm bore, suitable size of waste fittings, one pair of 600 mm long cast iron brackets, complete all as specified and directed.

S&F vitreous china wash hand basin white with flat back of size 550x400 mm, excluding chain and plug, taps and porcelain stopper but incl PVC waste pipe of 32 mm bore, suitable size of waste fittings, one pair of 600 mm long cast iron brackets, complete all as specified and directed.

Taking up or down existing GI tubing and connections, including making good the disturbed surface for 15 mm bore pipes complete all as specified and directed.

Taking up or down existing GI tubing and connections, including making good the disturbed surface for 20 mm bore pipes complete all as specified and directed.

Supply, fixing, laying & testing 15 mm bore galvanised iron water tubing 'medium grade' with and including all GI fittings such as flanges, unions, reducer sockets, socket, reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed to walls, ceilings or floors, complete all as specified and directed.

Supply, fixing, laying & testing 20 mm bore galvanised iron water tubing 'medium grade' with and including all GI fittings such as flanges, unions, reducer sockets, socket, reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed to walls, ceilings or floors, complete all as specified and directed.

Refixing old steel tubing and connections in new or old position (walls, ceiling, floors, etc.) for 15 mm dia pipes with and including all new fittings complete all as specified and directed.

Refixing old steel tubing and connections in new or old position (walls, ceiling, floors, etc.) for 20 mm dia pipes with and including all new fittings complete all as specified and directed.

Dismantling existing water storage tank of any description of capacity exc. 500 ltr but n.exc. 1000 ltr, complete all as specified and directed.

S&F in position rotational moulded polyethylene water storage tanks 1000 lts capacity, white colour (cylinderical vertical with closed top) hoisted and fixed in position, complete all as specified in SSR Part I and as directed. Note:- PVC tank shall be ISI marked and having three layers.

S&F in position rotational moulded polyethylene water storage tanks 500 lts capacity, white colour (cylinderical vertical with closed top) hoisted and fixed in position, complete all as specified in SSR Part I and as directed. Note:- PVC tank shall be ISI marked and having two layers.

S&F of 20 mm dia ball brass valve, high pressure with polythene float and fly nut, screwed down for iron pipe, complete all as specified and directed.

S&F in renewal of bib taps, cast copper alloy, with crutch or butterfly handles, screwed down, screwed for 15 mm bore GI pipe or for brass ferrule or to GI socket complete all as specified and directed.

S&F bib taps, cast copper alloy, with crutch or butterfly handles, screwed down, screwed for 15 mm bore GI pipe or for brass ferrule or to GI socket complete all as specified and directed.

S&F in renewal of pillar taps 15mm dia, cast copper alloy, with capston heads, chromium plated, fancy type, screwed down high pressure with or without lettered 'Hot' or 'cold' with long screwed shanks and flynuts screwed for 15mm bore iron pipe and fixed complete all as specified and directed.

S&F of pillar taps 15mm dia, cast copper alloy, with capston heads, chromium plated, fancy type, screwed down high pressure with or without lettered 'Hot' or 'cold' with long screwed shanks and flynuts screwed for 15mm bore iron pipe and fixed complete all as specified and directed.

S&F in renewal of angle valve 15 mm bore cast copper alloy, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for unions and fixed, complete all as specified and directed.

S&F angle valve 15 mm bore cast copper alloy, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for unions and fixed, complete all as specified and directed.

S&F vitreous china half stall type urinal, white with grating and union for discharge pipe, including providing and fixing plugs, bedding urinal against wall in CM 1:2, securing urinal to plugs with and including 60 mm long brass screws, including one PVC waste pipe of 32 mm dia, one CP waste coupling of 32 mm dia, pointing around urinal back with white cement, complete all as specified and directed.

S&F of vitreous china squatting pan Orissa pattern size 580 x 440 mm white with front or back inlet, integral foot rest incl providing lime concrete bedding and connecting to flusing cistern, complete all as specified and directed.

S&F vitreous china wash down water closet pan (pedestal pattern) white with 'P' or 'S' trap front or back inlet & including connection to drain or out going pipe and to flushing pipe, antisyphonage pipe etc., & including plastic seat cover white with flat bottom and mild steel chromium plated or aluminised hinging device, complete all as specified and directed.

S&F 10 Ltr capacity PVC low level flushing cistern, top push type with inlet ball valve, PVC float, brackets & including superior quality PVC flush pipe of 32 mm dia, complete all as specified and directed.

S&F toilet jet spray made of stainless steel with minimum 1 m long PVC pipe and CP brass connector suitable for 15 mm dia stop cock, including all accessories, fixed to EWC, complete all as specified and directed.

S&F in renewal of sink made of stainless steel double bowl 1mm thick kitchen or laboratory with plugs, washers and waste coupling, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets of suitable angle iron, 32 mm dia superior quality PVC waste pipe and connecting union to pipe overall size 1100 mm x 460 mm x 230mm, bowl size 510 mm x 405 mm x 230 mm, fixed in granite stone slab and top of granite stone match with top of kitchen sink complete all as specified and directed. Note :- Granite shall be measured and paid in appropriate item of BOQ.

S&F in renewal of stainless steel utensil plate rack of size 900 x 1200 x 200 mm, made of 0.60 mm thick stainless steel sheet and fixed in position, design and pattern as approved by the GE, complete all as specified and directed.

S&F in renewal of soap dish stainless steel, approx size 160x160x90mm, embedded in wall, complete all as specified and directed.

S&F soap dish vitreous china white, approx size 160x160x90mm, fixed to plugs with CP brass screws and pointing around edges with white cement, complete all as specified and directed.

S&F in renewal of grating doom of 140 mm dia, made of PTMT with or without waste hole (Minimum weight 50 gm), complete all as specified and directed.

S&F 75 mm dia PVC (SWR) floor trap, with CP grating including jointing to waste pipe with solvent cement and fixed in cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) complete all as specified and directed.

S&F in renewal of 75 mm dia PVC (SWR) floor trap, with CP grating including jointing to waste pipe with solvent cement and fixed in cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) complete all as specified and directed.

Dismantling cast iron or reinforced concrete drain pipes 100 mm bore alongwith fittings and accessories, jointed in CM and taking out from walls, floors or from trenches, if required, complete all as specified and directed.

Dismantling cast iron or reinforced concrete drain pipes 75 mm bore alongwith fittings and accessories, jointed in CM and taking out from walls, floors or from trenches, if required, complete all as specified and directed.

S&F cast iron (sand cast) soil, waste and vent pipe 100 mm bore in any length with or with out ears with cement joints laid in trenches or in floors, complete all as specified and directed.

S&F cast iron (sand cast) soil, waste and vent pipe 75 mm bore in any length with or with out ears with cement joints laid in trenches or in floors, complete all as specified and directed.

S&F 100 mm bore CI bend (any radius), diminishing pieces or tapers (larger bore measured), complete all as specified and directed.

S&F 75 mm bore CI bend (any radius), diminishing pieces or tapers (larger bore measured), complete all as specified and directed.

S&F cast iron (sand cast) soil, waste and vent pipe 100 mm bore in any length with or with out ears with cement joints fixed to walls, complete all as specified and directed.

S&F cast iron (sand cast) soil, waste and vent pipe 75 mm bore in any length with or with out ears with cement joints fixed to walls, complete all as specified and directed.

S&F PVC (SWR) pipe 110 mm bore, single socketed, in any length with rubber ring joints and fixed to wall, ceiling or floors with & including all accessories complete all as specified and directed.

S&F PVC (SWR) pipe 75 mm bore, single socketed, in any length with rubber ring joints and laid in trenches, ceiling or floors with & including all accessories complete all as specified and directed.

S&F PVC (SWR) bend 75 mm bore, any radius, incl jointing to waste pipe with solvent cement, complete all as required and as directed.

S&F PVC (SWR) bend 110 mm bore, any radius, incl jointing to waste pipe with solvent cement, complete all as required and as directed.

S&F PVC (SWR) 110 mm bore single Junction 'T', equal or unequal, incl jointing to waste pipe with solvent cement, complete all as specified and directed.

S&F PVC (SWR) 75 mm bore single Junction 'T', equal or unequal, incl jointing to waste pipe with solvent cement, complete all as specified and directed.

S&F PVC (SWR) vent cowl 75 mm dia, incl jointing to waste pipe with solvent cement, complete all as specified and directed.

M&L for cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested, for 150mm bore of pipe complete all as specified and directed.

M&L 150 mm bore Reinforced concrete pipes, class NP2, laid and jointed complete with collars, complete all as specified and directed.

Surface excavation not exc 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil, complete all as specified and directed.

Excavation over areas not exc 1.5 m deep and getting out in soft/loose soil, complete all as specified and directed.

Excavation in trenches not exc 1.5 m wide and not exc 1.5 m deep for foundation etc or for shafts, column footings or for laying cables etc not exc 10 Sqm on plan and getting out in soft/loose soil, complete all as specified and directed.

Returning filling in excavated soil including spreading, levelling, watering and well ramming in layers not exc 25 Cm, complete all as specified and directed.

Removing excavated materials (soil) not exc 50 m distance and depositing where directed at a level not exc 1.5 m above the starting point, complete all as specified and directed.

M&L hardcore (broken stone) of gauge not exc 63 mm, deposited spread and leveled in layers not exc 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendents, regulators, sockets, light fittings etc removing materials to store for reuse or for taking credit and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

Dismantling unserviceable main switch/DBs incl wooden board and deposit to MES store yard including making good disturbed surface of wall complete all as specified and directed.

Taking down sub main wiring /XLPE cable of any size/capacity complete all as specified and making good disturbed sufaces to match with the existing surface, complete all as specified and directed.

M&L for Point wiring with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable of size 1.5 Sqmm with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable of size 1.5 Sqmm as earth continuity wire to be drawn in and including PVC casing capping not less than 20 mm width with all accessories and fittings, fixed on surface including providing wooden rectangular block for mounting switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet cover and making good disturbed surfaces, complete all as specified and directed for the following: - One light/ceiling fan/exhaust fan/bell buzzer point controlled by one, one way switch of 5/6 Amps. Note :- Cutting chases (if required) and making good to match with the adjoining surface shall be included in the unit quoted rate.

All as per item No 154.00 (here-in-before) but one 5 Pin, 5/6 amps socket outlet point on independent board, controlled by one, one way 5/6 Amp switch.

All as per item No 154.00 (here-in-before) but one 5 Pin, 5/6 amps socket outlet point on same board, controlled by one, one way 5/6 Amp switch.

M&L Point wiring with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable of size 2.5 Sqmm, with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable FRLS of size 2.5 Sqmm as earth continuity wire to be drawn in and including PVC casing capping not less than 20 mm width with all accessories and fittings, fixed on surface for one socket outlet 15 amp on independent board including providing wooden/PVC rectangular block for mounting switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet cover and making good disturbed surface, complete all as specified and directed.

S&F switch piano flush type 5/6 Amps, 230 volts, single pole, one way, ISI marked, complete all as specified & directed.

Supply and fixing switch socket combination, 5/6 and 15/16 Amps, 230 volt, multi pin, flush type universal, complete all as specified and directed.

Supply and fixing socket outlet, 5/6 Amps, 230 volt, five pin, flush type universal, complete all as specified and directed.

S&F PVC/polycarbonate lamp holder, angular/batten type with back plate, ISI marked complete all as specified & directed.

S&F in renewal of stepped type electronic fan regulator, flush type, 230 volts AC, single pole, humming free, fixed on the existing phenolic laminated sheet, complete all as specified and directed.

S&F ceiling rose surface type PVC/Polycarbonate isolated body, 65x 50mm, 3 terminals, complete all as specified & directed.

S&F in renewal of wall mounted 18 watt LED Tube light fittings, batten type with bipin holders, powder coated steel with internally prewired, complete all as specified and directed.

S&F of wall mounted 18 watt LED Tube light fittings, batten type with bipin holders, powder coated steel with internally prewired, complete all as specified and directed.

S&F of 9 Watt LED bulb, B-22 type complete all as specified and directed.

S&F of LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection, complete all as specified and directed.

S&F in renewal of LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection, complete all as specified and directed.

M & L in renewal of street/road light GI mounting bracket made out of steel tube, medium grade, 40 mm dia (or higher size to suit the opening of the fitting) 1.50 mtr long by hydraulic pressed mechine bend to require arc shape and fixed to pole with 02 Nos MS flat iron clamps of suitable size fixed with bolts, nuts and washers including drilling holes and grouting with the same for fixing bolts as required & incl duly painted with two coat of aluminum paint over a coat of aluminum red oxide primer and fixing with lights fittings on the existing old street light poles complete all as specified and directed. Note :- Cost of Necessary tools and plants such as ladders, hydra for renewal of mounting brackets, light fittings, nuts, bolts etc shall be deemed to be included in the unit rate quoted.

M & L of street/road light GI mounting bracket made out of steel tube, medium grade, 40 mm dia (or higher size to suit the opening of the fitting) 1.50 mtr long by hydraulic pressed mechine bend to require arc shape and fixed to pole with 02 Nos MS flat iron clamps of suitable size fixed with bolts, nuts and washers including drilling holes and grouting with the same for fixing bolts as required & incl duly painted with two coat of aluminum paint over a coat of aluminum red oxide primer and fixing with lights fittings on the existing old street light poles complete all as specified and directed. Note :- Cost of Necessary tools and plants such as ladders, hydra for renewal of mounting brackets, light fittings, nuts, bolts etc shall be deemed to be included in the unit rate quoted.

S&F MCB, 6 to 32 Amps, Single Pole, 240 Volt, 10 KA 'B' curve including all accessories, complete all as specified and directed.

S&F MCB, 6 to 32 Amps, Single Pole & Neutral, 240 Volt, 10 KA 'B' curve including all accessories, complete all as specified and directed.

M&L for MCB DB made of sheet steel phosphatised, powder painted with bus bar 200 A, neutral link, earth bar and Din rail, 240 Volts SPN with 8 ways, Double door, complete all as specified and directed. Note for items of MCB DB - (1) The unit rate includes for cutting the brick/stone walls to accommodate DB to make flush to wall. (2) The unit rate includes for making good the disturbed surfaces including finishes to match with the adjoining surface.

S&F of sub main wiring with two runs of single core PVC insulated and unsheathed FRLS multistranded copper conductor cable of size 6 Sqmm LT, 1100 volts grade, drawn through and including 20 mm dia PVC non metallic surface conduit with accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. and fittings and one run of 6 sqmm single core multistranded FRLS copper conductor cable green colour as earth continuity conductor, complete all as specified & as directed. NOTE for items of submain wiring:- Two runs of cable one run of earth wire and one run of PVC non metallic conduit of 20mm dia shall be measured as one run length. Cable required for connection to DBs shall deemed to be included and shall not be measured separately. Earth wire shall run inside the PVC conduit.

M&L for Earthing with galvanized steel earth plate electrode of size 600 mm x 600mm x 6.0 mm, buried directly in ground (earth plate not less than 2.25 Mtr below normal ground level) connected to galvanized iron earth wire of 4 dia by means of bolts, nuts, check nuts and washers of galvanized iron including 15 mm bore light grade GI tubing for protection of earth wire, MS sheet metal funnel with wire mesh, watering pipe medium grade 20 mm bore, charcoal or coke and common salt in alternative layer of 15 Cm compacted thickness all around the electrode with concrete earth pit of PCC 1:3:6 type 75 mm thick precast RCC (1:2:4) type B1 pit cover reinfored with 8 mm dia deformed bar and suitable handle made of 10 mm dia round bar and necessary excavation, earth work, in soft/loose soil and disposal of spolis to a distance not exc 50 Mtr and necessary connection and testing complete all as shown in electrical plate No. 3 and including dismantling and taking out old earthing complete all as specified and directed. Notes: - (a) Irrespective of whatever is shown in plate No 5 of SSR, earth pit shall be casted in PCC (1:3:6) type C-1 and precast cover of RCC (1:2:4) type B-1 with suitable handle. (b) Item includes the cost of GI pipe for protection of earth wire and earth wire upto 7.5 m. Any variation below or above shall be measured and paid for separately under relevant item of this Sch ‘A’.

M&L for Earthing with galvanized steel earth plate electrode of size 600 mm x 600mm x 6.0 mm, buried directly in ground (earth plate not less than 2.25 Mtr below normal ground level) connected to galvanized iron earth wire of 4 dia by means of bolts, nuts, check nuts and washers of galvanized iron including 15 mm bore light grade GI tubing for protection of earth wire, MS sheet metal funnel with wire mesh, watering pipe medium grade 20 mm bore, charcoal or coke and common salt in alternative layer of 15 Cm compacted thickness all around the electrode with concrete earth pit of PCC 1:3:6 type 75 mm thick precast RCC (1:2:4) type B1 pit cover reinfored with 8 mm dia deformed bar and suitable handle made of 10 mm dia round bar and necessary excavation, earth work, in soft/loose soil and disposal of spolis to a distance not exc 50 Mtr and necessary connection and testing complete all as shown in electrical plate No. 3 complete all as specified and directed. Notes: - (a) Irrespective of whatever is shown in plate No 5 of SSR, earth pit shall be casted in PCC (1:3:6) type C-1 and precast cover of RCC (1:2:4) type B-1 with suitable handle. (b) Item includes the cost of GI pipe for protection of earth wire and earth wire upto 7.5 m. Any variation below or above shall be measured and paid for separately under relevant item of this Sch ‘A’.

S&F in renewal of electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc. & including connecting with and including PVC insulated three core 23/.0076 copper conductor cable, rubber insulated from ceiling rose to exhaust fan motor and writing MES No with black synthetic enamel paint 2.0 cm high complete all as specified and directed.

S&F in renewal of exhaust fan, steel body AC single Phase. 230V of size 300mm, sweep with, blades, and frame and louvers & including connecting with and including PVC insulated three core 23/.0076 copper conductor cable, rubber insulated from ceiling rose to exhaust fan motor and writing MES No with black synthetic enamel paint 2.0 cm high and including making appropriate hole in the wall/ window complete all as specified and directed.

S&F of exhaust fan, steel body AC single Phase. 230V of size 300mm, sweep with, blades, and frame and louvers & including connecting with and including PVC insulated three core 23/.0076 copper conductor cable, rubber insulated from ceiling rose to exhaust fan motor and writing MES No with black synthetic enamel paint 2.0 cm high and including making appropriate hole in the wall/ window complete all as specified and directed.

Supplying, laying, jointing testing and commisioning XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (heavy duty) with multistranded aluminum conductors, 1100 Volt grade of cross-sectional area 16 Sqmm, 2 core, laid in trenches / ducts / encased in GI pipe / fixed to pole/wall, complete all as specified and directed.

Supplying, laying, jointing testing and commisioning XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (heavy duty) with multistranded aluminum conductors, 1100 Volt grade of cross-sectional area 10 Sqmm, 2 core, laid in trenches / ducts / encased in GI pipe / fixed to pole/wall, complete all as specified and directed.

M&L dry clean Sand filling in trenches around underground cables for earth cushion, complete all as specified and directed. Note: - Depth of sand shall be measured after punning.

Supplying and laying pulverized fuel Ash-lime bricks (Fly ash bricks - non modular size), laid flat adjoining each other as in protection to UG cables, complete all as specified and directed.

M&L in renewal of 40 mm bore Steel water tubing, light grade, galvanised, with all fitting, laid in trenches/fixed to walls/poles etc as protection to cables, with and including necessary MS clamps, nuts botls, washers etc required for fixing, complete all as specified and directed.

K B Enterprises

ANNAPURNA ENTERPRISES

SARDAR PATEL ENTERPRISES

L P Singh and Co.

Ganesh Contruction

Aditya Enterprises