REPAIR MAINT REPLACEMENT OF SUBMAIN WIRING EARTHING INTERNAL FITTINGS AND FIXTURES INCLUDING CEILING FAN EXHAUST FANS ETC AT ICGS KAKINADA AND REPAIR MAINTENANCE OF COOLING APPLIANCES AND OTHER MISCELLANEOUS E M WORKS AT ICGS KAKINADA UNDER AGE

Amount

Taking down old unserviceable/deteriorated batten/PVC conduit point wiring from existing place i.e. light, fan, socket or power points complete with all unserviceable fittings such as switches, sockets, ceiling rose, pendants, Holders, etc and making good all disturbed surface to wall, floor etc by means of cement mortar (1 : 3) or plaster of Paris and to match and finish new surface as the existing surface either by using same colour distemper, Putti or white / colour wash complete all as specified and as directed.

M & L for concealed point wiring on wall and surface on ceiling/roof with necessary fixing arrangements with PVC-FRLS insulated and unsheathed copper multi-stranded conductor of size 1.5 Sq mm, 1100 volts grade drawn in and including rigid non metallic white / ivory PVC conduit medium grade ISI marked not less than 19 mm dia with all conduit accessories/ fittings such as junction boxes, bends, tee, elbow etc including anodized MS sunken boxes made out of MS sheet of thickness not less than 1.6 mm with earth dolly and Bakelite laminated sheet 3 mm thick ISI marked for fixing of switches / sockets, fan regulators, wall mounting fittings, door bell & bulkhead etc. with MS screw and cup washers including PVC-FRLS insulated and unsheathed copper multi-stranded conductor of size 1.5 Sqmm, 1100 volts grade for continuous earthing including cutting the chases and making good the surface by cement mortar (1:3) and for matching / finishing of new surfaces either by means of plaster of peris/ Putti or distemper / colour wash with same existing colour surfaces complete all as specified and as directed for the following:-For one light, fan, call bell, 5Amp independent socket point controlled by one switch

All as per item No 2 here-in-before but For one socket point controlled by one switch on same board complete all as specified and as directed.

All as per item No 2 here-in-before but for one light point controlled by two, two way switch.

All as per item No 2 here-in-before but for power point wiring with 4 Sqmm PVC-FRLS insulated, unsheathed, copper conductor, stranded 1100 volt grade cable and 2.5 Sqmm PVC-FRLS insulated, unsheathed, copper conductor, stranded 1100 volt grade cable as continuous earth lead.

All as per item No 2 here-in-before but in surface Casing/caping and surface mounted PVC/Poly carbonate sunken boxes of appropriate sizes mounted on surface for the following :- For one light, fan, call bell, 5Amp independent socket point controlled by one switch.

All as per item No 2 here-in-before but For one socket point controlled by one switch on same board.

All as per item No 2 here-in-before but for One light point controlled by two, two way switch.

All as per item No 2 here-in-before but in casing /caping for power point wiring with 4 Sqmm PVC-FRLS insulated, unsheathed, copper conductor, stranded 1100 volt grade cable and 2.5 Sqmm PVC-FR insulated, unsheathed, copper conductor, stranded 1100 volt grade cable as continuous earth lead. Note for item No 2 to 9: Make of Wire:- Havells / Finolex/ KEI / Polycab or equivalent Make specified in PS. Make of conduit:- Plaza/kalinga/AKG/Presto Plast/Finolex or equivalent Make specified in PS.

S & F in repairs, for switch flush type single pole one way 5 Amps, 240 volts, white finish complete all as specified. Make: Havells / Anchor / Legrand / Schneider

S & F in repairs for switch flush type single pole two way 5 Amps, 240 volts, white finish complete all as specified. Make: Havells / Anchor / Legrand / Schneider

S & F in repairs , for switch flush type 15 Amps, 240 Volts single pole white finish complete all as specified. Make: Havells / Anchor / Legrand / Schneider

S & F in repairs, for socket outlet 5 pin, 5 Amps flush type white finish complete all as specified. Make: Havells / Anchor / Legrand / Schneider

S & F in repairs, socket outlet 2 in 1, 3 pin, 5/15 A, flush type universal, 240 V white finish complete all as specified. Make: Havells / Anchor / Legrand / Schneider

S & F in repairs, electronic socket size, rotary, 5 speed step type regulator, 120-230 V white finish complete all as specified.

S & F in repairs, ceiling rose, surface backlite, 65 x 20 mm three terminal .

S & F in repairs, lamp holder insulated body with back plate suitable for angle / batten fitting.

S & F in repairs, double door metallic sheet metal enclosure for DB when MCBs to be used SPN 8 ways, 240 V with 200Amps rated bus bar complete fixed properly on in concealed position and to provide required sizes of flexible conduit at any open surfaces near DBs of cables/wires all as directed. Make: Legrand/Schiender/L&T or equivalent Make specified in PS.

S&F double door metallic sheet metal enclosure for DB when MCBs to be used TPNL, 4 ways, 415Volts (horizontal type) with 200 Amps rated bus bar suitable for TPN MCB/ 4 pole Isolator fixed properly on in concealed position and to provide required sizes of flexible conduit at any open surfaces near DBs for cables/wires complete all as directed. Make: Legrand/Schiender/L&T or equivalent Make specified in PS.

S&F in repairs testing and commissioning of MCB SP 240 volt 6 Amp to 32 amp 10 KA capacity having B-curve characteristics connected with suitable lugs. Make: Legrand/Schiender/L&T or equivalent Make specified in PS.

S&F in repairs testing and commissioning of MCB SPN 240 volt 6 Amp to 32 amp 10 KA capacity having B-curve characteristics connected with suitable lugs complete all as specified and as directed. Make: Legrand/Schiender/L&T or equivalent Make specified in PS.

S&F in repairs testing and commissioning of MCB TPN 240 volt 40 Amp to 63 amp 10 KA capacity having B-curve characteristics connected with suitable lugs complete all as specified and as directed. Make: Legrand/Schiender/L&T or equivalent Make specified in PS.

S&F in repairs testing and commissioning of MCCB 125 Amps, 4 Pole, 415V, 25KA capacity having B-curve characteristics connected with suitable lugs complete all as specified and as directed. Make: Legrand/Schiender/L&T or equivalent Make specified in PS.

S&F in repairs testing and commissioning of MCCB 100 Amps, 4 Pole, 415V, 25KA capacity having B-curve characteristics connected with suitable lugs complete all as specified and as directed. Make: Legrand/Schiender/L&T or equivalent Make specified in PS.

S&F in repairs testing and commissioning of MCCB 63 Amps, 4 Pole, 415V, 25KA capacity having B-curve characteristics connected with suitable lugs complete all as specified and as directed. Make: Legrand/Schiender/L&T or equivalent Make specified in PS.

S&F in repairs sheet metal enclosure , 25A single pole and neutral with a two pin and earth plug and socket complete in metal clad board (Industrial type) with one single pole MCB 25 Amp fixed properly on in concealed position complete all as specified and as directed. Make: Legrand/Schiender/L&T or equivalent Make specified in PS.

S&F in repairs metal clad socket industrial 2 pin & earth plug top 20A, 230V complete suitable for AC Box complete all as specified and as directed. Make : Legrand/Schiender/L&T or equivalent Make specified in PS.

M&L sub main wiring with two runs of single core PVC-FRLS insulated unsheathed multistranded copper conductor cable of size 6 sqmm drawn in new/existing conduit with 4.0 Sqmm PVC-FRLS insulated unsheathed multistranded copper conductor as a continuous earth wire complete all as specified including taking down old unserviceable sub main wiring complete all as specified and as directed. Note: (i) Two single core cable and one run of earth copper conductor will be measured and paid as one unit length (ii) Conduit pipe and fitting will be measured and paid separately.

M&L sub main wiring with two single core PVC-FRLS insulated unsheathed multistranded copper conductor cable of size 4 sqmm drawn in new / existing conduit with 2.5 Sqmm PVC-FRLS insulated unsheathed multistranded copper conductor as a continuous earth wire complete all as specified including taking down old unserviceable sub main wiring complete. Note : (i) Two single core cable and one run of earth copper conductor will be measured and paid as one unit length (ii)Conduit pipe and fitting will be measured and paid separately

S&F Energy efficient LED Batten light fitting 1x10 watt complete with all accessories & Provn of three core cable of copper conductor of size 0.75 sqmm, making necessary electric connetion from ceiling rose to fitting terminal , fixing the fitting on wall including all necessary fixing accessories complete all as specified and as directed. Make : Philips Cat No. BN 021 LED10S- 6500 PSU GR S1 or quivalent Make specified in PS.

S & F Energy saver LED Bright batten light fitting 22/20 watt, 230 Volts, Box type. etc and accessories,including required fixing arrangements and electrical connection three core copper cable from ceiling rose to light fitting old unserviceable bracket with sketch fitting complete all as specified and as directed. Make :Philips or quivalent Make specified in PS.

S & F in repairs 9 W LED Lamp 220-240V AC 50Hz ( 85% more energy saving as compared to incandescent lamp complete all as specified and as directed. Make Phillips /Havells/CG/Bajaj or equivalent Make specified in PS.

S&F Rigid non metallic medium white ivory PVC conduit medium grade (ISI marked) of size not less than 25 mm dia concealed position inclusive all fitting such as tee, bends, reducer, elbow, bell mouth, tube ends and all fixing accessories such as couplers lock, nuts, saddlers, pipe hooks etc fixed properly on as in concealed position incl cutting chasing & making good to disturbed surfaces & matching with the existing colour of wall/floor etc all as directed by Engineer-in-Charge.

M&L for Earthing complete with M.S. galvanized earth plate electrode 600 x 600 x 6 mm thick buried directly in ground (earth pit not less than 2.25 M deep below normal GL) with top edge of the plate not less than 1.5M below normal GL, connected to galvanized earth lead wire 4 mm dia by means of bolts, nuts, check nuts & washers of GI or steel incl excavation, PCC (1:3:6) type C-1 chamber with RCC cover (1:2:4) type B0, 40 mm thick reinforced with 6 mm dia bar, 3 Nos. both way, 15 mm dia light grade GI protection pipe, funnel with wire mesh,watering pipe of size 20 mm dia med. grade, lugs, main Earthing lead upto 7.5 mtr incl. Charcoal dust, salt etc. all as shown in electrical plate No. 3 of SSR Pt-I 2009 specification.

S & F in repairs Condensor 2.5 mfd complete all as specified and as directed .

M&L for periodical Servicing of Air conditioner Split type (High wall / Tower AC) of capcities 1.5 to 2.0 TR complete on site or civil workshop with disconnecting electrically from Main supply , Applying high speed air blower on evaporating unit and condensing unit, fan motor, blower, housing, filters etc.Checking up all electrical parts like Blower Motor, condensor Motor, swing motor, capacitor, PCB,drain pipes and interconection between evaporative unit and condensing Unit and testing of wiring of connections,cleaning and identifification of defects and its rectification/replacement with same specification and same capacity, Checking of Insulation of copper tubing of refrigerant lines,connecting valve and gas pressure of unit,replacement of Insulation leakage detection if any and leakage rectification, cleaning entire units internally and externally and replacement of necessary parts,Oiling of Moving parts,Motors,Tighteing of Nut bolts,Screw,Thimles, reassembling, connecting with supply both unit and testing complete to make the unit in fully affactive cooling and airflow. Note : Spare parts, gas charging shall be measured and paid separatelty under respective item of BOQ.

Supply only for incorporation in Item No. 36 during the Maintenance /repairs to Air conditioners Split type :

Running Capacitor 20-25 MFD

Running Capacitor 30-45 MFD

S & F Starting Capacitor 60-80 MFD

S & F Starting Capacitor 90-120 MFD

Capacitor 2.5 Mfd for Evaporating Fan Motor

Capacitor 6 Mfd for Condensing Fan Motor

Evaporator blower as per sample

Condensor Fan blade as per sample

Printed Circuit board/Electrinic Control kit of split AC as per sample

Nylon Filter

Condenser Fan Motor for split AC 1.5 TR as per sample

Condenser Fan Motor for split AC 2 .0 TR as per sample

Evaporating Blower Motor of 1.5 ton AC as per sample

Evaporating Blower Motor of 2 ton AC as per sample

Compressor Sealed Unit for AC of capacity 2.0 TR

Compressor Sealed Unit for AC of capacity 1.5 TR

Outer grill of Condensor unit as per sample

Swing motor for Split AC as per sample

Thermostat Switch

Over Load Protection Coil

Wiring Kit of Split AC 1.5/2 Ton

Cooling Coil as per existing make and model /type

Condensing Coil as per existing make and model /type

Drain pipe of best quality as per existing dia and lenth

Connecting Cable of 40/.0076 three core copper PVC insulated round

Connecting block of Condensor Unit

Connecting block of Evaporating Unit

M & L for Copper tubing of appropriate size made of copper for discharge line including jointing with existing system with help of flare tool etc. and connecting up with discharge valve both side with entire satisfaction of Engr-in-Charge.

M & L for Copper tubing of appropriate size made of copper for suction line including jointing with existing system with help of flare tool etc. and connecting up with suction valve both side with entire satisfaction of Engr-in-Charge

M & L for Recharging of refrigerants Gas in Split type AC complete all as specified and as directed.

M&L for periodical repairs and maintenance of water cooler of cooling capacity upto 60 Ltrs / Hr and storage capacity upto 120 Ltrs complete with disconnecting the water connection, inserting dead plug, dismantling the fan motor, taps, fan blades, condenser etc.Checking up and rectification to wiring and connections, replacement of necessary parts and accessories, cleaning of the cold water tank, piping, refrigerant lines, reallignment of the fan coil unit and replacement of drain pipe , connecting to water mains and testing to make the unit in fully functional condition. Note: 1. Equipment Shall be serviced once for every quarter and reptated maintenance shall not be measured( i.e. duplication of mainetnance shall not be easured). Labor Charge for On site repairs is deemed to be included in the quoted rate of the job. 2. Spares replaced during the process of repair shall be measured and paid separately under relevant item herein after. 3. Rates shall include the cost of dismantling and transporting the Water Cooler to workshop.

Supply only spares incorporated during the repairs to Water Cooler vide Sl Item No. 41 herein before :-

Thermostatswitch with knob

Push tap inner / outer thread chromimum plated of size 1/2 ".

Rubber gasket with PVC sheet for Top Lid

Condenser fan motor for water cooler.

Capacitor for water cooler

Starting Relay as per Sample

PVC Hose Pipe size 3/4 " to 1 "

Waste water tray as per sample

Compressor Sealed unit for water cooler of capacity upto 120Ltrs

Condenser unit for water cooler

Overload protection for Water cooler

Capillary tube of water cooler

S & F in repairs 115 mm dia ball brass valves, high pressure with Polyethylene float and flynut complete screwed for Iron pipe on or brass ferrule and fixed complete all as specified and as directed.

S & F in repairs Sheet Metal enclosure with 2 pin and earth plug and socket complete with one single pole MCB SP of Capacity upto 32 Amps 240 Volts complete all as specified and as directed.

M & L for Recharging of refrigerants Gas in water cooler of any capacity and any type complete all as specified and as directed.

Note for item Nos. 36 to 45 : The makes of the items/spare parts shall be as per existing make at site or as decided , recommened by Engineer-in-Charge and approved by AGE(I).

Taking down ceiling fan / exhaust fan of any sweep and any make, dismantling for replacing defective parts, overhauling, cleaning, greasing, rewinding, etc and hanging up / fixing back in the original position including provision of 3 core 0.5 sq mm copper flexible cable from ceiling rose to connecter, connecting up and testing complete all as directed. Notes : 1. Replacing of defective parts such as capacitors, nuts and bolts with split pin, rubber reel, bearings etc. will be measured and paid for separately 2. Rewinding and painting of fan will be measured and paid for separately under relevant item of BOQ.

Rewinding ceiling fan single phase, 230 volt of 1200 /1400 mm sweep with super enameled copper wire of exisiting gauge including insulation material varnishing and drying complete all as specified and as directed.

All as per Item No. 48 herein before but for exhaust Fan, Pedestal fan, wall fan, table fan 225 /300 /400 mm Sweep complete all as specified and as directed.

M & L for Painting of ceiling fan, exhaust fan, wall fan, pedestal fan for any size and type, scraping out of old paint filling of cavities with filler preparation of body and clearing of dust etc. one coat of painting with synthetic enamel paint by Spraying with first Quality Paint and writing of MES number complete all as specified and as directed

Supply only following items for repairing fans in respective item No.47 of this schedule:

Capacitor up to 2.5 Mfd MAKE KELTRON, APCOS

Capacitor 3.15/ 4 MFD MAKE KELTRON, APCOS

Capacitor Clamp with Connector

Rubber Insulator suitable for any type of Ceiling Fan.

Mild steel Down Rod with Clamp nut bolts & split pin for 600 mm Long

Mild steel Down Rod with Clamp nut bolts& split pin for 900 mm Long

Exhaust Fan bracket with frame Nut, Bolt, Rubber reel etc mplete 300 mm sweep

Exhaust Fan bracket with frame Nut, Bolt, Rubber reel etc complete 450 mm sweep

Ball bearing suitable for any type of fans Make : SKF,TATA,NBC

Gun Metal bush suitable for any type of fan

Mild steel shaft for fan

Ceiling Fan Blade suitable for 1200/1400 mm sweep

Exhaust Fan Blade suitable for 300 mm sweep

Exhaust Fan Blade suitable for 450 mm sweep

Ceiling fan Canopy Set of two

Exhaust fan louvers of size 450mm sweep

Exhaust fan louvers of size 300 mm sweep

Note for item Nos. 51.01 to 51.17 : The makes of the items/spare parts shall be as per existing make at site or as decided , recommened by Engineer-in-Charge and approved by AGE(I).

ANJALI ENTERPRISES