Addition alteration and renovation of KH T II Set No 2 at Kumar house Shimla 4 HP

Amount

15.23 Dismantling tile work in floors and roofs laid in cement mortar including stacking material within all lead & lift.15.23.1 For thickness of tiles 10 mm to 25 mm

15.12 Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within all lead & lift : 15.12.1 Of area 3 sq. metres and below

6.13 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. 6.13.1 Cement mortar 1:3 (1 cement :3 coarse sand)

13.8 15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix :13.8.2 1:4 (1 cement: 4 fine sand)

Providing and fixing 2mm thick PVC antistatic venyl Flooring plain or coloured, carbed or mosaic/metalled finish laid with approved adhesive on sub-floor (damp proofing treatment to be paid

8.2 Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.8.2.2 Granite of any colour and shade 8.2.2.2 Area of slab over 0.50 sqm

11.38 Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete. (Nitco, Orient bell, Kajaria, Johnson make)

8.31 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. (Nitco, Orient bell, Kajaria, Johnson make)

9.1 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately )9.1.2 Sal wood

9.5 Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-incharge.(Note:- Butt hinges and necessary screws shall be paid separately) 9.5.2 Kiln seasoned and chemically treated hollock/Marandi wood 9.5.2.1 35 mm thick shutters

9.7 Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick : 9.7.4 Ply wood 7 ply, 9 mm thick 9.7.4.1 Decorative plywood one side decorative veneer and commercial veneer on other face (Type 1) conforming to IS 1328 BWR Type

9.7.7 Float glass panes 9.7.7.1 4 mm thick glass pane (weight not less than 10 kg per sqm)

9.7.8 Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia. wire and 1.4mm wide aperture with matching wood beading

9.96 Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc.complete :9.96.2 250x16 mm

9.97 Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 9.97.4 150x10 mm

9.100 Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete. 9.100.1 125 mm

14.35 Providing and fixing bright finished brass hard drawn hooks and eyes : 14.35.2 250 mm

1218000000 Providing and fixing / Repair & replacement of 19mm thick water proof commercial board in shelves/box for cupboard with butt joints & fixing with nails & screws etc complete).

1217900000 Providing and fixing / Repair & Replacement of 19mm thick Commercial Board water proof shutters for cup boards i/c fixing with nickel plated piano hinges with screws etc complete)

1218200000 Providing and fixing / Repair & Replacement of 1.00mm thick coloured or plain lamination sheet (sunmica) on boards/ply wood sheets with approved adhesive and nails etc complete.

9.112 Providing and fixing 2nd class teak wood lipping/ moulded beading or taj beading of size 18X5 mm fixed with wooden adhesive of approved quality and screws/nails on the edges of the Pre-laminated particle board as per direction of Engineer-in-charge.

9.81 Providing and fixing bright finished brass handles with screws etc. complete: 9.81.2 100 mm

9.114 Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete. 9.114.2 Double strip (horizontal type)

14.56 Taking out existing wooden door/Window shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge.

Providing and fixing PVC panel sheet ceiling 6.5 -9mm thick of approved quality with butt jointing and screws (frame work and cover fillets to be measured and paid for separately) (LG or equivalent make).

9.46 Providing and fixing chromium plated brass curtain rod having wall thickness of 1.25mm with two chromium plated brass brackets fixed with C.P. brass screws and PVC sleeves etc., wherever necessary complete :9.46.2 20 mm dia

9.47 Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets :9.47.1 20 mm dia (heavy type)

9.12 Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured).

17.31 Providing and fixing 600 X 450mm beveled edge mirror of superior glass of required size (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

17.32.4 Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :17.32.4 Rectangular shape 1500x450 mm

21.1 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in charge. (Glazing, paneling and dash fasteners to be paid for separately). 21.1.1.2 Powder coated aluminium (minimum thickness of powder coating 50 micron)

21.1.2 For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) 21.1.2.2 Powder coated aluminium (minimum thickness of powder coating 50 micron)

21.3 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):21.3.2 With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm)

21.2 Providing and fixing 12mm thick pre laminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer- in-charge 21.2.2 Pre-laminated particle board with decorative lamination on both sides

10.25 Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. 10.25.2 In gratings, frames, guard bar, ladder,railings, brackets, gates and similar works (Jindal TATA or equivalent Make).

Providing and fixing 0.35mm thick prepainted liner sheet in eaves board /facia/soffits /ceiling including cutting, fixing with prepainted iron J or L hooks, bolts & nuts 6mm dia & prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer in Charges i/c scaffolding and Shuttering (Tata/ JSW).

Providing and fixing wooden plank ceiling with tongued and grooved jointing and wood screws (frame work and cover fillets to be measured and paid for separately). Second class deodar wood in planks. 20 mm thick

15.52 Dismantling of flushing cistern i/c WC of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead.

17.2 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :17.2.1 W.C. pan with ISI marked white solid plastic seat and lid (Cera/ Hindware/ Bathsense)

18.8 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc.18.8.1 15 mm nominal outer dia Pipes

18.12Providing and fixing G.I. pipes complete with G.I. Fittings including trenching and refilling etc.18.12.1 15 mm dia nominal bore.

17.10 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :17.10.2 17.10.2 Kitchen sink without drain board17.10.2.2 17.10.2.2 610x460 mm bowl depth 200mm

17.7A Providing and fixing wash basin with C.I. brackets, 15mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer (Cera/ Hindware/ Jaquar make)

17.8 Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

17.28 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete17.28.2 17.28.2 Flexible pipe 17.28.2.1 17.28.2.1 32 mm dia

18.21 Providing and fixing uplasticised PVC connection pipe with brass unions :18.21.2 45 cm length 18.21.2.1 15 mm nominal bore

17.73 Providing and fixing CP towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

17.74 Providing and fixing CP shelf 440 mm long, 124 mm width and 36 mm height of approved quality and colour, weighing not less than 300 gms.

18.65 Providing and fixing CP soap Dish/Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

18.53 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 18.53.1 15mm nominal bore (Jaguar Make or equivalent Make)

17.16A Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :17.60.2 100 mm inlet and 75 mm outlet 17.60.2.3 Hubless centrifugally cast iron/PVC epoxy coated inside & outside as per IS:15905

12.46 Providing and fixing to the inlet mouth of rain water pipe CP grating square (Slit) 150 mm square with a height of 8 mm and weighing not less than 100 gms.

18.15 Providing and fixing brass bib cock of approved quality: 18.15.1 15 mm nominal bore(Jaquar/Cera/Bathsense or equivalent make)

Providing and fixing Mixer for kitchen sink with casted swinging spout at top (Jaquar/Cera/Bathsense or equivalent make)

17.22B Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge.(a) 15 mm nominal dia (Jaquar/Cera/Bathsense or equivalent make)

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 12.41.1 75 mm diameter

12.41.2 110 mm diameter

12.42 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 12.42.5 Bend 87.5°. 12.42.5.2 110 mm bend

12.42.1 Coupler 12.42.1.2 110 mm

12.42.5.1 75 mm bend

12.42.1 Coupler 12.42.1.1 75 mm

DALIP SINGH VERMA (BID ID -526976)

C AND E CONSULTANCY (BID ID -527300)