MISC REPAIRS INCLUDING ROOF TRATMENT, CEILING CHAJJA REPAIR, SENITARY FITTING, ROLLING SHUTTER BLOCK MASONARY AND ALLIED B/R REPAIRS UNDER AGE B/R-II AREA AT MIL STN KOTA

Amount

Taking down cement plaster of any description and thickness on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

Dismantling floor, hearth or wall tiling/ terrazzo including cement mortar bedding (but not backing), removing tiles and rubbish off the premises, complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floor and pavings n.exc 15 cm thickness (below or above GL) and removing rubbish from premises, complete all as specified and directed.

Demolition/Dismantling of existing normal roof treatment, any type from RCC roof slab including lime concrete/PCC padding over roof, removing layer of bitumen under lime concrete/PCC padding, cement mortar, felt etc and cleaning the surface by hacking to receive plaster and removing demolished materials outside MD land, complete all as specified and directed.

Demolition of brick work/stone boulder masonry, built in CM incl all quoins, arches, pillars etc but excluding ashlar facing, dressed stone work and precast concrete articles, complete all as specified and directed.

Dismantling of existing water storage tank of any description of capacity exc. 250 ltr but n.exc. 500 ltr, complete all as specified and directed.

Dismantling of existing water storage tank of any description of capacity exc. 500 ltr but n.exc. 1000 ltr, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge, any thickness incl hooks and ridge as retrieved from site complete all as specified and directed.

M&L for PCC 1:2:4 mix type B-0 (Using 12.5 mm graded stone agg) for roof padding, leveling course to receive floor finishes etc, complete all as specified and directed.

M&L brushing neat cement slurry with 3.00 kg cement per Sqm, complete all as specified and directed.

M&L for applying 20 mm thick screed in CM 1:3 on roof slabs with using liquid water proofing compound as per manufacturer's instructions, complete all as specified and directed. (Liquid WPC shall be measured and paid separately).

Supply only approved liquid water proofing compound, complete all as specified and directed.

M&L for cleaning of roof slab including picking, sweeping clean and washing down with water to remove dust, dirt etc and Supply and fix APP polymeric water proofing membrane, minimum 3mm thick and weighing not less than 3.0 Kg/Sqm, black finish reinforced with non-woven polyester matt, with a thermo fusable finish laid over cold applied bituminous primer conforming to IS 3384 @ of 0.40 Kg/Sqm torching overlaps with a propane or a butane gas torch, with a overlap of 75mm at the sides and 100mm at the ends and sealing including applying a coat of cold emulsion bituminous primer all as per manufacturer’s instructions, complete all as specified and directed. Note: (i) Coved fillets in PCC(1:2:4) type B-0 using 12.5mm graded stone aggregate, of radius 75mm shall be provided at the junction of roof and parapet wall/mumty/chimney/other vertical surfaces and thereafter surface painted with hot paving bitumen of Grade 30/40 confirming to IS-73, [email protected] Kg/Sqm over a coat of cold applied bituminous primer conforming to IS:3384 @ 0.40 Kg/Sqm.

Item 14.00 Contd........ (ii) Polymeric membrane shall be taken to a height of 45cm (minimum) and then inserted inside the groove of parapet wall of brick masonry and shall be finished by a membrane flushing. (iii) The waterproofing treatment shall be got carried out by the manufacturer or their authorized applicators. (iv) In case of stone masonry parapet wall etc a groove of size 25mmx25mm (minimum) shall be made in coved fillet at the junction of roof and parapet wall/mumty Chimney/other vertical surfaces and polymeric membrane inserted in groove and sealed with paving bitumen. (v) Cost of above aspects is deemed to be included in quoted rates.

M&L for cleaning of walls and floor of sunken portions including picking, sweeping clean and washing down with water to remove dust, dirt etc and Supply and fix APP polymeric water proofing membrane, minimum 3mm thick and weighing not less than 3.0 Kg/Sqm, black finish reinforced with non-woven polyester matt, with a thermo fusable finish laid over cold applied bituminous primer conforming to IS: 3384 @ 0.40 Kg/Sqm, torching overlaps with a propane or a butane gas torch with an overlap of 75mm at the sides and 100mm at the ends and sealing including applying a coat of cold applied bituminous primer all as per manufacturer’s instructions, complete all as directed. Note :- (i) Polymeric membrane shall be laid in sunken floor and on sides up to finished floor level. (ii) The waterproofing treatment shall be got carried out by the manufacturer or their authorised applicators. (iii) Supply only water proofing liquid shall be measured and paid seperately. (iv) HDPE spout pipe 32mm bore of required length shall be provided and rates for same shall be included in above quoted rate. (v) Cost of above aspects are deemed to be included in quoted rate.

M & L for PCC 1:5:10 type E-2 (using 40mm graded crushed stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

Dismantling loose concrete cover of RCC columns, beams, slabs, Chajjas and the like as directed ,roughening and cleaning concrete surfaces with steel wire brushes,washed with water and allowed to dry,including dusting of steel reinforcement,providing fabric mild steel wire mesh 75 mm x 75 mm of 2 mm dia as reinforcement to concrete surfaces,applying adhesive/admixyure over steel mesh and providing ordinary portland cement 53 grade and 2 parts of banas sand mixed with adhesive/admixture at the rate as per manufactures instruction or 2% by wt of cement all as directed with apressure of 2 to 2.5 kgs per sqm by guniting machine including necessary padding,steel scaffolding and shuttering for working platform/formwork etc complete all as specified and directed

Supply, febrication and fixing mild steel work with hollow section square or rectangular section as in framed Trusses, purlins and rafter including necessary welding bolting complete with using ERW or ERW or induction butt welded tubes confirming to IS. 1161-1979 grade St-240 complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet, 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering, wall cladding etc, fixed to iron/wooden members with self drilling zincoulium coated metal screws having cap with rubber and metal washers, complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet, 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering, wall cladding etc, fixed to iron/wooden members with self drilling zincoulium coated metal screws having cap with rubber and metal washers, complete all as specified and directed.

Dismantalling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed.

M&L for Anodised Aluminium snap grid (minimum 15 microns anodisation) of size 605 x 605 mm with anodized aluminum angle of size 40mm x 25mm x 2mm thick weighing 0.36 Kg per running meter and anodized aluminum main and cross T of size 36.50 x 23.50 x 1.50 mm thick weighing 0.254 Kg per running meter and 23.50 x 23.50 x 1.50 mm thick weighing 0.202 Kg per running meter respectively for false ceiling all as specified and directed

S&F hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long suitable for size of snap grid 605 x 605 mm complete all as specified and directed

M&L for Gypsum board 12mm thick in ceiling fixed with screws on snap grid all as per manufacturer instructions complete all as specified and directed

M&L for perforated particle board/ tiles for insulation and accoustic purposes of size 60x60cms, 12mm thick fixed with staples on snap grid in ceiling complete all as specified and directed.

Excavating in post holes (or similar holes) in soft/loose soil, each not exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm around foundation concrete as ordered, watering and removing surplus soil to a distance not exceeding 50 m and making good surface, complete all as specified and directed.

M & L for PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

M & L for PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

Taking down existing rolling shutter complete any type width and height n.exc 3.0m in any position keeping a side for repair and refixing in the same position after repairing old hood covers of any thickness and replacement of defective parts/components with new parts to make the shutters serviceable including necessary reveting, bolting, punching, oiling and greasing properly as required complete all as specified and directed. Note :- Defective parts/components as required for rollinf shutter shall be paid on supplied only under appropriate items of BOQ.

Supplying only guide channel of depth 50mm to 150mm as required at site and width of guide channel 25mm including fixing of cleats or supports on both faces, the thickness of channel shall not be less than 2.00mm and the spacing of cleats shall not exceed 0.75m complete all as specified and directed.

Supply only fabricated lock plate made of the MS flat iron 35x6 mm and 400mm long sliding plate complete with arrangement for locking with pad locks and handles of mild steel fixed on both the interior and exterior side of lock plate complete all as specified and directed.

Supply only bevel gear box with gear rod and crank handles for gear operated type rolling shutter (Mechanical type) fixed with and including ball gear bearing complete all as specified and directed. Make :- Arun/Kumar/Gandhi.

Supply and fabricating 1.25mm thick MS sheet rolling shutter strip size 75 to 100mm wide and shape as required at site for rolling shutter including cutting punching of required shape and size each alternative lath sections shall be fitted with MS clips secured with rivets at either complete all as specified and directed.

Supply only springs for rolling shutter upto height 3.00m complete all as specified and directed.

Supply only MS pipe medium grade 50mm dia complete all as specified and directed.

S&F in renewal of 0.80mm thick MS plain black sheet as in hood cover of rolling shutters cut to size, edges beaded if directed holes punched, including round headed, screw fixed to steel member etc, with plain 40mm tap joint, including bending, turning up, mitred angles, stopped ends as required complete all as specified and directed.

Taking down existing rolling shutter complete any type width and height not exceeding 3M in any position complete all as specified and directed.

M & L for 1.25mm thick steel rolling shutter upto height 3M, without ball bearing as specified including guide channel, top covers anchoring rod, hasp and staple and other necessary, accessories required to function the shutter and applying two coats of synthetic enamel paints over one coat of primer erected-in passion as indicted complete all as specified and directed.

M&L Glazed ceramic coloured tiles on vertical surfaces 350x 250x7 mm/450X350X7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match, laid over and including 10 mm thick rendering in CM 1:4 backing, complete all as specified and directed.

M&L for joint free non skid ceramic coloured tiles, 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for joint free non skid ceramic coloured tiles, 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for joint free non skid ceramic coloured tiles, 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, fixed on vertical surfaces, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 10 mm thick rendering in CM 1:4, complete all as specified and directed.

M&L for light coloured vitrified tiles, 10mm thick (square/ rectangular) area of each tile not exceeding 0.36 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for light coloured vitrified tiles, 10mm thick (square/ rectangular) area of each tile not exceeding 0.36 Sqm & fixed on vertical surfaces, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 10 mm thick rendering in CM 1:4 backing, complete all as specified and directed.

M&L for rendering 15 mm thick on stone masonry surfaces or other than fair faces of brick work in cement mortar 1:6, surface finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 15 mm thick on stone masonry surfaces or other than fair faces of brick work in cement mortar 1:4, surface finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 10 mm thick on fair faces of ceiling in cement mortar 1:3 including finishing the surface even and smooth, complete all as specified and directed.

M&L brick work with pulverized fuel Ash-lime bricks (Fly ash bricks - non modular size), straight or curved on plan exc 6 m mean radius, built in CM 1:6, complete all as specified and directed.

M&L for brick work with pulverised fuel Ash-lime bricks (Fly ash bricks - non modular size), straight or curved on plan to any radius in half brick walls built in cement mortar 1:4, complete all as specified and directed.

S&F in position rotational moulded polyethylene water storage tanks 500 ltrs capacity, white colour (cylinderical vertical with closed top) hoisted and fixed in position, complete all as specified in SSR Part I and as directed. Note:- PVC tank shall be ISI marked and having three layers.

S&F in position rotational moulded polyethylene water storage tanks 1000 ltrs capacity, white colour (cylinderical vertical with closed top) hoisted and fixed in position, complete all as specified in SSR Part I and as directed. Note:- PVC tank shall be ISI marked and having three layers.

S&F 20 mm dia ball brass valve, high pressure with polythene float and fly nut, screwed down for iron pipe, complete all as specified and directed.

S&F in renewal of PVC connection 450 mm long suitable for 15 mm GI pipe with two PTMT nuts and rubber washers complete all as specified and directed.

S&F in renewal of 15mm bore angle valve cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as specified and directed. Make :- Hindware cat part No F 740039/cera cat part No G1017201/Johnson cat part No T 2610 C 4 or techno commercially equivalent makes specified in PS.

S&F in renewal of pillar taps, 15 mm dia, cast copper alloy, fancy type, swan neck type with capstan heads, with chromium plated, screwed down high pressure with or without lettered 'hot' or cold with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed. Make :- CERA Cat No. F1003103 /JAQUAR cat No. COP-021PM /Hindware Cat No. F 74002 or techno commercially equivalent makes specified in PS.

S&F in renewal of 32 mm bore waste fittings brass CP for wash hand basin etc with long screwed and fly nuts, flange end embedded in red lead cement and other end fixed, complete all as specified and directed.

S&F in renewal of PVC waste pipe 32/40 mm dia and 1150 mm long, suitable for wash hand basin etc, complete all as specified and directed.

S & F in renewal of vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests including PVC(SWR) 'P' or 'S' trap connecting to flush pipe and to anti syphonage pipe, complete including making good to floor complete all as specified and as directed. Make :- CERA Cat No COVYNA S 3010109 /Johnson cat part no P0461PW0400/hindware cat part no J8365 or techno commercially equivalent makes as specified in PS.

S&F in renewal of vitreons china wash down water closet pan, padestal type, white, with 'p' or 's' trap & including recessed bottom PVC seat cover of white colour and mild steel chromium plated hinging device but excluding flushing cistern, flush pipe and fixing bolt and making connections to drain or outgoing pipe and to flushing pipe, anti-syphonage pipe etc, fixed in repairs, complete all as specified and directed. Make :- CERA Cat No Conventional Pro 520*360*390, S1059101/ JAQUAR Cat No. CWS WHT-551PNPP1841Z/ JOHNSON Cat No. J 8312 or techno commercially equivalent makes specified in PS.

Supply and fix in renewal of PVC valveless, syphonic action type, flushing cistern, 10ltr capacity, low level, white, with inlet, ball valve, float and handle including brackets, connections to pipes and fixing of chain and pull, or lever, complete all as specified and as directed. Make :- Cera Cat No. B1010102L/Johnson cat part No J 85821C or techno commercially equivalent makes specified in PS.

Supply and fix in renewal of vitreous china wash basin white counter sunk type, size 580x430 mm & including 32 mm dia CP waste fitting and PVC waste pipe 610 mm long and brackets complete all as specified and directed. Make :- CERA Cat No S 2040109/ JAQUAR cat No. OPs WHT-1580I/JOHNSON Cat No J8396 CH or techno commercially equivalent makes specified in PS.

S&F in renewal of vitreous china urinal half stall type flat back size of white with grating and union for discharge pipe including chromium plated water spreader , connection pipe and discharge down pipecomplete all as specified and directed.

S&F in renewal of vitreous China urinals size of 465x355x265 mm, white, bowl type (back to corner wall type), complete including providing and fixing plus, bedding urinal against wall in cement mortar 1:2 securing urinal to plus with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. , including waste coupling, PVC waste pipe, Urinal spreader, 15mm dia &300mm long PVC connection complete all as specified and directed.

M&L for preparing new steel surfaces exceeding 10cm width or girth and applying two coats of synthetic enamel paint over and including one coat of red oxide zinc chrome primer, complete all as specified and directed.

M&L preparation of newly plastered surfaces of walls and applying 1 mm thick wall care putty as per manufacturer's instructions and over it applying by roller two coats of distemper oil emulsion over & including one coat of suitable primer, complete all as specified and directed.

M&L applying three coats of white wash after preparation of new plastered surfaces of walls, complete all as specified and directed.

M&L applying three coats of white wash after preparation of new plastered surfaces of ceiling, complete all as specified and directed.

M&L for applying two coats of cement based paint on newly plastered surfaces of walls over & including a coat of white wash including preparation of surfaces, complete all as specified and directed.

M & L for Chisel the crack to a 'V' groove of 5mm x 5mm clean the groove to remove all loose laitance and wash with water apply crack filler, Dr Fixit crack-X Paste/Dr Fixite crack X powder with a putty blade or techno commercially equivalent makes specified in PS complete all as specified and directed.

Draining out water, cleaning and removing accumulated slufge/dirt scales from tank bottom, side and from moiths of circulating pipes of service tank of capacity not exceeding 500 ltrs, located on roof of the building and disinfecting the tank using bleaching powder to make the tank bacteria free, writing by stencil date of cleaning of tank with white synthetic enamel paint on black ground " CLEANED ON ( DATE)" height of the words 100mm, complete all as specified and directed.

Draining out water, cleaning and removing accumulated sludge/dirt scales from tank bottom, side and from mouths of circulating pipes of service tank of capacity exceeding 500 ltrs but not exceeding 1000 ltrs, located on roof of the building and disinfecting the tank using bleaching powder to make the tank bacteria free, writing by stencil date of cleaning of tank with white synthetic enamel paint on black ground " CLEANED ON ( DATE)" height of the words 100mm, complete all as specified and directed.

Supply and fixing in renewal of plastic water closet seat cover, coloured, for pedestal pan closed pattern with flat bottom, and cover with mild steel chromimium plated or aluminised hinging device complete all as specified and as directed.

ANNAPURNA ENTERPRISES (BID ID -3057463)

M/S MOHINI ENTERPRISES (BID ID -3057763)

M/S R.K. Builders & Developer (BID ID -3058231)

SINGH ENTERPRISES (BID ID -3057808)

L P Singh and Co. (BID ID -3057288)