CERTAIN PROVN WORKS AS A PROVISION OF 01 X GUARD ROOM (01 PLUS 3) WITH ATT TOILET BATHROOM AT MAIN GATE OF 164 MH , PROVISION OF SAA STORES PRISIONERS CELL WITH ATT TOILET NEAR QTR GD OF 1821 MED REGT AT TELEPARA-2 , CONSTRUCTION OF CEMENT GARBAGE CO

Amount

Schedule 'A'

Surface excavation n.exc (not exceeding) 7.50 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and as directed.

Excavation in trenches, n exc 1.5 mtr wide and n exc 1.5 mtr in depth for foundation etc. or for shafts, wells, cesspits, manholes, pier holes etc. n exc 10 Sqm on plan and n exc 1.5 mtr in depth and getting out in soft/loose soil complete all as specified and as directed by Engr-in-Charge.

M&L PCC (1:4:8) type D2 (using 40 mm graded stone aggregate) for fdn/ mass concrete complete all as specified and as directed by Engr-in-Charge.

M&L for RCC M-25 (Nominal Mix ) (1:1.5:3), Type B1 20 mm graded aggregate in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified.

M&L for RCC M-25 (Nominal Mix ) (1:1.5:3), Type B1 20 mm graded aggregate in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified.

M&L for RCC M-25 (Nominal Mix ) (1:1.5:3), Type B1 20 mm graded aggregate in cover slab/Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

M&L for RCC M-25 (Nominal Mix ) (1:1.5:3), Type B1 20 mm graded aggregate in Columns, pillars, piers, posts and struts

M&L TMT bars10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

Ditto as above but 6 to 8mm dia

M&F Formwork flat fair finished to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified.

M&L Formwork flat fair finished surfaces to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and as directed.

M&L Formwork square, rectangular or plougonal fair finished surfaces to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified.

M&L for Formwork to flat fair finished to soffits of suspended slabs such as roof slabs, floor slabs, landings , shelf and similar work; not exceeding 200mm thick (Horizontal or sloping)

M&L for Flyash Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in cement mortor 1:6 complete all as specified and as directed by Engr-in-Charge.

M& L for Fly ash Brickwork with sub-class `B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM (1:4) complete all as specified and as directed by Engr-in-Charge.

M&L for rendering 15 mm thick on brick work or concrete surfaces in cement mortar (1:4) finished surfaces even and smooth complete all as specified and as directed.

M&L for rendering 15 mm thick on brick work or concrete surfaces in cement mortar (1:6), finished surfaces even and smooth complete all as specified and as directed.

Rendering 10mm thick with CM (1:3) on or concrete surfaces finished even and smooth as in ceiling complete all as specified and as directed by Engr-in-Charge.

M&L for preparing new plastered surfaces of wall with wall care putty and applying two coat of distemper oil emulsion over a coat of primer complete all as specified.

M&L for preparation new plaster surfaces of wall and applying two coats of cement base paint complete all as specified and as directed by Engr-in-Charge.

M&L preparation of new plaster surface of ceiling and applying two coats of white wash complete all as specified and as directed by Engr-in-Charge.

Hardcore of gauge n exc. 63 mm, except material retreived from item 1 deposited, spread and levelled in layers n exc.15 cm thick, watered and rammed to a true surface

M&L silver sand filling under floors/cable protection or in foundations including watering and consolidation complete all as specified and as directed by the Engr-in-Charge.

M&L for cement concrete type B-1 1:2:4 (20 mm graded stone aggregate) as in floor finished complete all as specified and as directed by Engr-in-Charge.

M&L for Damp proof course to horizontal or vertical surfaces in cement mortar 1:2:4 type B0 including necessary formwork

M&L for Ceramic tiles (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed in cement mortar 1:6 complete all as specified.

Ditto as in skirting

Supply & fixing of 4.80 mm thick Sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane

Supply & fixing of Galvanised steel wire cloth. 0.63 mm nominal dia of wire and average width of aperture 1.40mm complete all specified.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

S&F Factory Made Solid PVC Moulded Door Shutter with wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face, supplying & fixing in frame at site as per specification & drawing

S&F Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc. complete all as specified and as directed.

M & L for in Pressed steel framesOF 125X60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified

S&F of 35mm thick 2nd class hard wood, plain, framed, panelled shutter (two panel) with panel of timber flat on both sides (feather edged), or of veneered particle board with comercial face veneers, supplied and fitted to chowkats all as specified and as directed.

S&F 35mm thick glazed skelton shutter open rebated and prepaid to receive glass gauze extra (without sash bar), edges of plain, chamfered or rounded fitted with cut and mitred beads for secuering glass excecter size of members of shutter including bidding to frame as specified in SSR part-I, sec 8 clause 8.20(a) all as specified and directed.

M & L PCC (1:3:6) type C1 as in holdfast block, coping, bedblock etc.

S&F Stainless steel butt hinges medium weight 100mm long for PVC door.

S&F Aluminium anodized barrel tower bolts, extruded section 200mm long.

S&F Aluminium anodized handles, D type, 150mm long

Supply & fix as for steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay complete with glazing bars, dovetailed or welded all as directed by the Engr-in-Charge.

All as per item No 50 here-in-before but without glazing bars.

M&L for Framed work such as grills, framed guard bars,for window by welding it to existing window frame and similar work con- forming to Fe.290.Gde-E-165

M&L for PCC 1:3:6 type C-1 using 20 mm graded stone agg as in plinth protection complete all as specified and as directed.

S&F Steel ventilators with centre hung shutter including two pairs of brass cup pivots, catch spring and pulley wheel, complete all as specifed.

S&F of 4 mm thick Sheet glass frosted , ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane

M&L for two coat of synthetic enamel paint over a coat of yellow primer including preparation on steel surfaces of any description over 10 cm width or girth complete all as specified and as dircted.

S&F vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) water closet, white complete all as specified and as directed by Engr-in-Charge.

S/F in 10 litres cap PVC low level valve less symphonic action type flushing cistern white with inlet, ball valve, float and handle including brackets and flushing pipe, complete all as specified and as directed by Engr-in-Charge.

S&F Vitreous China wash basin Pedestal pattern, white, flat back size 580x450 mm including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipeincluding brackets, complete all as specified and as directed by Engr-in-Charge.

S&F 15mm bore Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed by Engr-in-Charge.

S&F 15 mm dial PVC connection 450 mm long, complete all as specified and as directed by Engr-in-Charge.

S&F waste coupling of PTMT (half of full threaded) complete all as specified and as directed by Engr-in-Charge.

S&F Grating doom 100mm dia of PTMT (Minimum weight 25gms) complete all as specified.

S&F 15mm bore Bib taps, cast copper alloy fancy type chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed

S&F swivel shower of brass CP with shower arm 125 mm size for fixing with 15 mm bore GI pipe complete all as specified and as directed (Make -Prayag/Marc/Essco/Jaquar).

S&F 15 mm bore Stop valves, cast copper alloy, fancy type chromium plated screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed

S&F Towel Rail 450mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 170gms)

M&L for coloured Glazed ceramic tiles in vertical surface 450x 300x 5-6mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick rendering in CM (1:3) complete all as specified.

M&L for coloured joint free non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors, skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with tile including 15mm thick screed bed in cement mortor 1:6 complete all as specified

M&L for PVC Floot trap 75 mm outlet, plain with grating including joning with solvent cement complete all as specified and as directed by Engr-in-Charge.

M&L PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement

M&L for 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors

Ditto as above but in wall complete all as specified.

M&L for 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors

M&L for 110 mm bore PVC (SWR) vent cowl

M&L PVC (SWR) bends with access door of 110mm bore any radius complete all as specified.

S&F 1000 ltr Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified.

M & L screed bed or bedding layer 15 mm thick screed bed or bedding layer in CM (1:4) mixed with WPC as per manufacturer instruction for laying of APP membrane complete all as directed by the Engr-in-Charge.

Supply only intergral water proofing compound (WPC) of best quality

M& L for bituminous primer @ 0.50 KG/Sqm over the cement plaster incl preparation of surfaces as per manufacturers instruction complete all as specified and as directed by the Engr-in-Charge.

M & L APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified and as directed by Engr in Charge.

M & L for finishing the Bituminous surface with aluminium paint @0.15 Ltr/sqm as per manufactures specifications and under strict supervision of manufactuer's technical representative complete in all respects as directed by Engr-in-Charge

S&F 15 mm dia medium grade galvanized steel tubing with all fittings fixed to walls, ceilings or laid under floors all as specified and directed.

All as peritem above but 20 mm bore pipe.

S&F of viterous china urina, half stall type, white including spreader ( excluding flushing cistern, flush pipe and west pipe)

Returning filling including spreading levelling watering and well ramming in layers n. exc 25 cm in soft /loose soil complete all as specified and directed.

Removing excavated material ( soil) n. exc 50 m depositing where directed at a level n. exc 1.50 m above the starting point all as specified and directed.

M&L for PCC for concrete bed to drain pipe , 200 mm bore pipe including packing and under hunching against the sides of pipe after they are laid and tested in PCC (1:3:6) type C-2 using 40 mm graded stone aggreagate complete all as specified and directed.

Surface dressing n.exc (not exceeding) 15cm deep and getting out in Soft/loose soil complete all as specified and directed.

M&L for for preparation of newly wall plastered surfaces and applying three coats of colour wash on wall as specified as diracted.

M& L Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete

M& L for Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required covering to door shut ters; covering to door chowkats (frames); chullah hoods; water tanks; water troughs; ducts; urinal troughs and funnels, etc. cut to size edges beaded if directed, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel members, etc., with plain 40 mm lap joints or welded/ riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. as required

M&L for 100 mm thick cement concrete type B1, 1:2:4 (20mm graded aggregate) as in base for interlocking etc for vehicle to move complete all as specified and as directed.

M & L for forming 12mm thick Expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘A’

M&L Brick work with Locally available best quality bricks , laid on edges on top surfaces of drains,bedded and jointed in CM (1:6) and Pointed in CM (1:3) complete all as specified and as directed.

M&L Brick work with Locally available best quality bricks , laid flat on verticle inclined sides of drains,bedded and jointed in CM (1:6) and Pointed in CM (1:3) complete all as specified and as directed.

M&L for plain cement concrete 1:2:4 Type Bo (using 12.5mm graded stone aggregate as in coping etc including necessary form work complete all as specified and directed.

M&L for preparation new plaster surfaces of wall and applying 1 mm wall care putty and two coats of weather coat paint complete all as specified and as directed by Engr-in-Charge.

M&L for 100 mm thick cement concrete type C1 (1:3:6 ) Norminal mix as in subbase of floor etc and finished the complete all as specified and as directed.

S&F steel work in i.e. Truss bottom, top bend, sides, side supports, holding plates, posts and base plate for stud co;umn in rcc etc including special shaped washers etc complete using ERW or induction butt welded tubes conforming grade St-240 complete all as specified and as directed by the Engr-in-Charge.

S&F angle iron, MS flat iron in wind ties and similar work confirming to Fe 410-0 or Fe 310-0.complete all as specified and as directed by the Engr-in-charge

S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and as directed by the Engr-in-Charge.

S& F OF Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

M&L point wiring complete with FRLS PVC insulated unsheathed multistranded copper conductor of size 1.50 sqmm nominal cross sectional area single core drawn in and including 20mm dia 'medium grade' PVC concealed conduits and fittings, including cutting chasingin brick wall n.exc 10cm width or girth(excluding ceiling surface), pressed steel concealed terminal switch boxes not less than 1.2mm thick of reqd size factory made duly painted inside and outside with two coats of black bituminous paint over one coat red oxide primer, 3mm thick plastic laminated sheet top cover (ISI Marked) fitted with chromium plated brass screws & washers complete including 1.50 sqmm nominal cross sectional area PVC insulated unsheathed multistranded copper conductor green as earth wire connected to earth dolly with all accessories including making good disturbed surfaces with CM(1:4) with treating the surfaces as per existing finishes complete all as specified and directed. (a) One light point controlled by one way switch 5/6 amps.

(b) One ceiling fan/Exhaut fan point controlled by one way switch 5/6 amps.

(c) 3 pin socket outlet, 5 amp on same board controlled by one way switch 5/6 amp complete all as specified and directed.

(d) 3 pin socket outlet, 5 amp on independent board controlled by one way switch 5/6 amp complete all as specified and directed.

All as per item 95 above but wiring with 2.5 sq mm single core copper conductor for one socket out let 15/16 amps point on the independent board complete all as specified and directed.

S&F switch piano flush type 5/6 amps single pole one way all as specified.

S&F socket 2 in 1, 3 Pin, 5/6 amps, complete all as specified and directed.

S&F of Switch socket combination 2 in 1,3 Pin 5/15 Amp multipurpose 230 volt flush type complete all as specified and directed by Engr-in-Charge.

S & F deluxe fan Electronic regulator AC 50 Hzs rotary step white/ivory finish complete all as specified and directed.

S&F ceiling rose, bakelite, surface type, 220/240 volts, three terminals complete all as specified and directed.

S&F IP-20, LED light 20 W 94 (feet), 5700K, wall/ surface mounted, integrated type with aluminume housing and decorative caps with integrated high efficiency electronic driver and surge supprssor of 2 KV or more luminency> lumens/watt, power factor> 0.90, operating range 140-270V, 50Hz fixed with 02 Nos of PVC round/ square blocks, screws etc complete with all accessories internally prewired and connecting up complete all as specified and directed.

S&F High Power LED street light fitting ,system wattage-35 Watt, made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having IP65 protection and impact resistance of IK07 with 10KV built in surge protection device using 2.5 Sqmm PVC insulated three core copper cable including taking down all as specified and directed.

Supply and Fixing MCB DB double door, powder coated sheet metal enclosure, 8 way 240 volts grade single pole and neutral with 200 amps rated bus bar,IP 43 protection fixed to wall using nuts & bolts and washer of suitable dia and grouted to wall using suitable gutties complete all as specified and as directed.

S&F street light bracket, made out of GI pipe medium grade) 25mm bore, 1.2 m long bend to shape and fixing/grouting with wall using 2 Nos 25 x 5 mm size MS FI clamps with bolts, nuts & washers complete including drilling as necessary and two coats of Aluminium paint over a coat of Red oxide primer all as specified & directed.

S&F MCB single pole & neutral 32 amp, 415 volts, 'C' series, 10 KA breaking capacity & making connection complete all as specified and directed.

S&F MCB single pole, 6 to 32 amps rating, 240 volts, 'C' series, 10 KA breaking capacity & making connection complete all as specified and directed.

M&L for Earthing complete with galvanised steel plate electrode of size 600x600x6.30mm thick burried directly in ground with earth pit not less than 2.25 meter deep below normal ground level with top edge of plate not less than 1.5 meter below normal ground level connected to galvanised 4 mm dia earth lead by means of nuts bolts check nuts GI washers earth wire protected by galvanised iron pipe 15mm bore (Light grade) for building LT wall panel all as directed including concrete pit in PCC (1:3:6) type CI, precast RCC cover slab of size 30x30x10 cm with one handle for lifting made out of 8 mm diameter MS bar finnel wire mesh 20 mm bore galvanised iron pipe (medium grade) for watering charcoal or coke and salt in alternate layers necessary earth work in soft/loose soilwith and including taking down the old one complete all as shown in electrical plate No 3 of SSR Part I 2009 including testing on completion all as specified and directed.

S&F ceiling fan complete with blades, down rods and accessaries incl provn of hook for hanging ceiling fan, 230V, 1200mm sweep, BEE star rated with brushiess directed current (BLDC) motor complete all as specified and directed.

Supply and lay pipe galvanised Mediun class including fittings 25mm dirrected by Engr-in -Charge

Supply and fix Gun metal gate Valves with iron wheel head of 25 mm dia bore complete with all accessories all as specified and directed by Engineer-in-charge.

M&L for cutting existing GI pipe alteration or addition of 40/50mm dia bore for insertion of reducer tee complete all as specified and as directed.

Supply, laying, jointing & testing trenches or passing through pipe, 1100 volts grade XLPE insulated PVC bedded galvanised steel strip wire armoured LT electric power UG cabele hevy duty with standered alu conductor of cross section area 16sqmm 2 core withh and including all fixing and connecting accessories such as alu cable lugs cable gland nut bolt waser ect complete as directed

M&L for GI tubing 40 mm bore ,light grade with all necessary fittings laid in trenches/under road crossing/fixed on pole/wall/under floor including suitable mild steel FI clamps of required size complete all as specified and directed.

Supply and laying sub class 'B' bricks of size 25cm x 12.5cmx 7.5cm (+/-10% tolerance) for protection of UG cable with width equal to length of bricks as mechanical protection laid dry and flat across the length of cable for protection of cable complete all as specified and directed

Supply and Fixing MCB DB double door, powder coated sheet metal enclosure, 4way 240 volts grade single pole and neutral with 200 amps rated bus bar,IP 20 protection fixed to wall using nuts & bolts and washer of suitable dia and grouted to wall using suitable gutties complete all as specified and as directed.

S&F exhaust fan of 300mm sweep A/C single phase 230/240 volts heavy duty complete with fan motor, blade, bracket and ring including grouting anchor bolts and making good to disturbed surfaces to match the existing complete including provision of PVC insulated & PVC sheathed round flexible cable of copper conductor,Three core of size 0.5 sqmm from ceiling rose to connector of fan, surface of the wall shall be made good by cement work/plastering and matching by existing colour ,all the metal part shall be painted two coats of synthetic enamel paint over a coat of primer, writting the MES no. with white colour paint complete all as specified and directed.

SINGH & CO

M/s. MD IRSHAD

R.K AND COMPANY

SS SHARMA

Biswanath Sharma