Construction work for Community Hall For Vadivasahat At Harij Nagarpalika Second Attempt

Name of Work :- Construction work for Community Hall For Vadivasahat At Harij

Memorandum showing items works to be carried out :

QuantitiesE Item Of Work Tendered Rate Total Amount

QuantitiesE Item Of Work Tendered Rate Total Amount

stimated Unit according to

બાબ કામ ની બાબત In Figure Rs. Ps

Excavation for foundation upto 1.5 m depth

including sorting out and stacking of useful

materials and disposing off the excavated stuff upto

50 Meter lead.(A) Loose or soft soil

Providing and laying cement concrete 1:4:8 (1-

Cement : 4- coarse sand : 8- Crushed stone

2 7 aggregates 40 mmnominal size) and curing 2780.37 Cu.Mt

complete excluding cost of formwork in (A)

Foundation and Plinth

Providing and laying cement concrete work 1:1.5:3

(1- Cement : 1.5- Coarse sand : 3- graded stone

aggregates 20 mm nominal size) and curing

complete excluding cost of formwork and

reinforcement for reinforced concrete work in (A)

Foundations, footings, Base or columns and

Mass concrete (Rate = {3888.70 +(5.234*70) } =

Providing and laying ordinary cement concrete

1:1.5:3 (1- Cement 1.5- coarse sand : 3- graded stone

aggregates 20 mm nominal size) and finishing

smooth with,curing etc. complete including the cost

4 4 of formwork but excluding the cost of reinforcement 9062.91 Cu.Mt

for R.C.C work in (B) COLUMNS: (iii) Having cross-

sectional area more than 0.12Sq.M and upto

Filling available excavated earth (excluding rock) in

trenches. plinth, sides of foundations etc. in layers

5 16 not exceeding 20 cm. in depth consolidating each 137.47 Cu.Mt

disposited layer by ramming and watering.

Filling in foundation and plinth with murrum or

selected soil in layers of 20cm. thickness including

watering, ramming and consolidating etc. complete.

Filling in plinth with sand under floors including

7 6 watering ramming, consolidating and dressing 429.24 Cu.Mt

Carring out plinth treatment to post construction /

existing structure by spraying chemical solution for

termite control treatment including labour and

material consistment with I.S.I specification. Using

Chlordene and Chiorpurfiles 20 EC. As Per

6131_paret-II Consentration Weight one percent is

recommended i.e one litre 20 EC chemical emulsion

with 19 liter give 1 % concrentration inclusive of

one litre chemical emulsion appication at the rate of

5 Litre chemical / Sqm of surface is recommended

Providing and laying ordinary cement concrete

1:1.5:3 (1- Cement 1.5- coarse sand : 3- graded stone

aggregates 20 mm nominal size) for R.C.C lintel

9 1 including finishing smooth with,curing etc. complete 10589.44 Cu.Mt

including the cost of formwork but excluding the

cost of reinforcement .(Rate = {10118.21

Providing and laying cement concrete 1:1.5:3 (1-

Cement : 1.5- Coarse sand : 3-graded stone

aggregates 20 mm nominal size) for reinforced

concrete Chhajjas not exceeding 10cm. thickness

upto floor two level including finishing the exposed

surfaces with cement mortar 1:3 (1- cement, 3 Fine

sand) to give a smooth and even surface centering

and formwork and curing complete excluding cost of

reinforcement. (Rate = {6462.17 +(5.23*70) } =

Providing and Laying ordinary cement concrete

1:1.5:3 (1- Cement 1.5- coarse sand : 3- graded stone

aggregates 20 mm nominal size) and finishing

smooth with curing etc. complete including the cost

11 8 of formwork but excluding the cost of reinforsement 6674.24 Cu.Mt

for R.C.C work in (iv) Slabs having more than 13 cm

and upto 15 cm.thickness.(Rate = {6241.78

Providing and laying ordinary cement concrete

1:1.5:3 (1- Cement 1.5- coarse sand: 3- graded stone

aggregates 20 mm nominal size) and finishing

smooth with,curing etc. complete including the cost

12 7 of formwork but excluding the cost of reinforcement 6948.11 Cu.Mt

for R.C.C work in (A) BEAMS :(iii) Having cross-

sectional area more than 0.12Sq.M and upto

Providing TMT Bar FE 500D reinforcement for R.C.C.

13 2880 work including bending, binding and placing in 77.29 K.g

position complete upto floor two level.

Brick work using common burnt clay building bricks

having crushing strength not less than 35 kg./Sq.Cm.

in foundation and plinth in Cement Mortar 1:6 (1-

Cement : 6 -fine sand) a for brick work in

superstructure above plinth level upto floor two

level (B) Conventional

Providing 15mm thick cement plaster in single coat

on Rough (Similar)side of single or half brick walls

15 178 for interior plastering upto floor two level and 168.87 Sq.Mt

finished even and smooth in (ii) Cement mortar 1:4

(1-cement :4-sand)

20mm thick sand faced cement plaster on walls upto

height 10 metres above ground level consisting of

16 132 12mm thick backing coat of C.M. 1:3 (1-cement : 3- 330.72 Sq.Mt

sand) and 8mm thick finishing coat of C.M. 1:1 (1-

cement : 1-sand) etc. complete.

Wall painting (two coats) with plastic emulsion

paint of approved brand and manufacture on

undecorated wall surface to give an even shade

including throughly brushing the surface free from

mortar droppings and other foreign matter and sand

papered smooth.

P & L 24" x 24" vitrified 8 mm thick tile flooring over

20 mm (average) base of cement mortar 1:6 (

cement: 6 coarse sand) on new surface or fixing on

existing flooring by adhesive material including

dismentaling of existing flooring and jointed with

color cement slurry including finised with flush

pointing & cleaning the surface etc. complete for

DARK shade and light shade

Providing and fixing M.S. door and window

prepared with ms equal angle for frame and shuter

with 18 BSG. Sheet Including Fixture and fastening

Including Red lead paint with two coat oil paint etc.

Including fixing in position .(As per R.A.)

Providing and fixing M.S. window with Ms Grill

prepared with ms equal angle for frame and shuter

with 18 BSG. Sheet Including Fixture and fastening

Including Red lead paont with two coat oil paint etc.

Including fixing in position .(As per R.A.)

Point wiring for Light / Bell with 2-1.5 sq.mm & earthwire

of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade

FRLS PVC insulated multistrand copper wires, in below type

of pipe erected with 6A Modular type switch / bell push &

accessories and earth continuity of following type, erected

on PVC / Metallic/Wooden box, single mounting base frame

21 15 covered with textured/metallic front plate modules erected on 419.15 Pt.

/ in wall / ceiling as per pipe erected, with necessary Lamp

holder/ceiling rose / H.D.Connector as directed. (f) with

medium class Rigid PVC pipe and accessories erected

concealed in wall/ceiling complete Cat. III

Point wiring for FAN with 2-1.5 sq.mm & earthwire of

sq.mm (Green) both are of .ISI marked 1.1 KV Grade FRLS

PVC insulated multistrand copper wires, in below type of

pipe erected with 6A Modular type switch and hum free

EME four or more step type electronic fan regulator with

separately mounted and accessories with earth continuity of

following type erected on PVC / Metallic/Wooden box,

22 2 single mounting base frame covered with textured/metallic 598.93 Pt.

front plate modules erected on / in wall / ceiling as per pipe

erected. with necessary ceiling rose / H.D.Connector as

directed. (f) with medium class Rigid PVC pipe and

accessories erected concealed in wall/ceiling complete Cat.

Point wiring for Looped Plug with 6A Modular type switch

& 5 pin socket erected on PVC / Metallic/Wooden box,

single mounting base frame covered with textured / metallic

23 4 front plate modules erected on / in wall / ceiling with 241.39 Pt.

following type accessories Cat. III

Supplying and erecting LED indoor fittings with LEDs of

wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB,

with housing used as a heat sink shall be made of thick sheet

Steel conforming to IS: 513/CRCA/ aluminium die cast

powder coated and high U.V. & corrosion resistance with

diffuser with company mark/name 160V to 270V, Power

Factor more than 0.9, THD < 15%,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE:

Below description have shown ranges of Wattage capacity of

LED fittings.The Engineer incharge may select any wattage

capacity between the ranges shown.) (i) 5-10 Watts, Surge-2

KV, IP-20, conventional 1 to 2 feet Cat-lll

Supplying and erecting LED indoor fittings with LEDs of

wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB,

with housing used as a heat sink shall be made of thick sheet

Steel conforming to IS: 513/CRCA/ aluminium die cast

powder coated and high U.V. & corrosion resistance with

diffuser with company mark/name 160V to 270V, Power

Factor more than 0.9, THD < 15%,

Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE:

Below description have shown ranges of Wattage capacity of

LED fittings.The Engineer incharge may select any wattage

capacity between the ranges shown.) (iv) 22-24 Watts, Surge

- 2KV,IP-20, conventional 4 feet Cat-lll

Approved make Earth fault Relay suitable to mount with

inter connection to moulded case circuit breaker having CT

ratio & MCCB rating as following along with shunt trip

26 1 220V AC. with all internal connections & complete erected 4983.34 Ea.

in existing M.S.housing..

Providing and erecting Sheet Steel powder coated MCB

distribution board - flush / surface mounted fitted with

busbar, neutral link, earth bar and DIN rail, confirming to IS

27 1 13032 and BS 5486-1986 without MCB to house appropriate 248.46 Ea.

nos. of MCBs.(The DBs should be used of same company of

MCB to be used)

(A) Single phase 4 way single door

Supplying & erecting earth pit of minimum bore dia.150mm

size approved make Earthing Electrode consisting Pipe-in-

Pipe Technology as per IS 3043-1987 made of corrosion free

hot dipped G.I.Pipes having Outer pipe dia of 50mm having

80-200 Micron galvanising, Inner pipe dia of 25 mm having

200-250 Micron galvanising, connection terminal dia of

12mm with constant ohmic value surrounded by highly

conductive compound with high charge dissipation suitable

for following type of applications with chamber and heavy

duty cover.(approved make OEM has to submit test

certificate) & having back filling compound of (B) Inner

chemical (CCM Compound)- Resistivity:- 0.2 / meter

testing as per IEC 62561-2017, Voltage drop:- < 1 volt at no

load & dry form, Sulphar content:- <2%(C) Back fill

Compound :- Earthing compound should be capable to

retain moisture for long time Necessary test report must be

(a) For Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

Providing & erecting Approved make Ceiling Fan with

double ball bearing ISI mark with Condenser 230 volt

A.C.50 Hz. 1200 mm sweep complete having 4 blades

29 4 Aluminium body and blade sets having ornamental design 2358.35 Ea.

shanks, canopy erected with earthing [ Make shall be

approved by Engineer in Charge]

Supplying and erecting 19 / 20 mm. nominal bore Medium

Class M.S. Pipe down rod erected duly painted for fan

30 4 complete with proper insulation without leakage and earthing.

Supplying & erecting Fan Hook of 10 mm M.S. Round

3`1 4 bar grouted in RCC slab with Making the site as 43.43 Ea.

Supplying & erecting fan hook box of 10 mm M.S.

round bar bounded to the RCC bars up to 50mm

length each side and pierced through a 16 Gauge

M.S. box / Heavy Duty PVC box complete erected

concealed in Ceiling with necessary finishing.

Providing Fan clamp of 30 x 5 mm flat of required

33 4 length & 10 mm M.S. Bolt & Nuts erected with 98.98 Ea.

necessary hook of 10 mm M.S. Round Bar.

Providing 2.5mm.thick laminated acrylic sheet to

cover the fan hook or Fan box.

Survaying,Planinig, Estimation, and Supervision Charge @3 %

I/We am/are willing to carry out the work at .............................................% above/below percent

(should be written in figures and words) of the estimated rates mentioned above. Amount of my/our

tender works out as under.

Estimated amount Estimated amount

Put to tender Rs……………………… Put to tender Rs………………………

Deduct .............% below Rs………… Add............% above Rs……………

Total Rs………… Total Rs……………

(*Please strike out whichever is not applicable).

Note PMC & TPI Charges will be deducted from Contractor's Bill